PROVN OF SENTRY POST ALONGWITH GUARD ROOM AND TOILET NEAR ENTRY GATE AT NAGTALAO UNDER GE BANAR

Surface dressing n exc. 15 cm deep complete all as specified.

M&L for earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m in hard rock complete all as specified.

M&L for earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift exc. 1.5m in hard rock complete all as specified.

M&L for earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m in any type of soil, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. complete all as specified.

M&L for cement Concrete in foundation, filling and mass concrete Type D2, 1:4:8 ( 40 mm graded aggregate) complete all as specified.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions. Square,Rectangle or Polygon (Substructure) complete all as specified.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions. Square,Rectangle or Polygon (Superstructure) complete all as specified.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified.

Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified.

M&L for RCC, M-25 (20mm graded Aggregates) in foundation, including rafts, footings, foundation beams, plinthbeams, bases for columns, etc, basement slab, under reamed piles and mass concrete.

M&L for RCC, M-25 (20mm graded Aggregates) column, pillars, piers, posts and struts. (Substructure) complete all as specified.

M&L for RCC, M-25 (20mm graded Aggregates) column, pillars, piers, posts and struts. (Superstructure) complete all as specified.

M&L for RCC, M-25 (20mm graded Aggregates) slabs supported on walls, beams and column in floors, roof, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L for RCC, M-25 (20mm graded Aggregates) chajjas complete all as specified.

M&L for RCC, M-25 (20mm graded Aggregates) beams, cantilevers, bressumers, lintel over 1.5 mt span complete all as specified.

M&L for Hard core, of stone broken to gauge n exc 63 m complete all as specified.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified.

M&L Reinforcement Bars Mild steel bars 10 mm dia and over, cut to length, bent to shape requied, including cracking, bending soirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securing with clips quality conforming to TMT bars complete all as specified.

M&L Reinforcement Bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified.

M&L for squared rubble walling, Jodhpur type brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified.

M&L Brickwork with subclass B bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified.

M&L Brickwork with bricks straught or curved on plan to any radius in half brick thick walls, built in cement mortar 1:6 complete all as specified.

M&L 10 mm thick cement plaster in CM 1:6 on brick walls finishing fair and even internally complete all as specified.

M&L 5 mm thick cement plaster with water proofing compoundover a backup coat of 10 mm thick in CM 1:4 on brick walls finishing fair and even externally complete all as specified.

M&L Integral Water Proofing compound complete all as specified.

M&L for Rendering 5 mm thick cement plasterbon fair face of brick surfaceor concrete surfaces in CM 1:3 in soffits of slab complete all as specified.

M&L Machine cut kota stone slab 20-25 mm thick having size 550 x 550 mm laid over and including 20 mm thick screed bed in CM 1:4 and 100 mm thick PCC Type C2(1:3:6) (40 mm graded aggregate) over rammed earth complete all as specified.

M&L Non skid coloured ceramic tiles 7-8 mm thick minimum size if tiles shall be 300 x 300 mm laid over and including 20 mm thick CM 1:4 screed and 40 mm thick PCC type B1 1:2:4(20 mm graded aggregate) laid over and 100 mm thick PCC type C2 1:3:6 (40 mm graded aggregate) over rammed earth complete all as specified.

M&L Machine cut polished kota stone slab 20 mm thick laid over and including 10 mm thick CM 1:3 screed for fixing vertical finishes complete all as specified.

M&L for Glazed ceramic tiles 6-7 mm thick over and including 10 mm thick CM 1:3 screed upto lintel height complete all as specified.

M&L for Preparing surfaces plastered or unplastered and applying Three coats of white washing on walls complete all as specified.

M&L for Preparing surface plastered or unplastered and applying Two coats of cement base paint over one coat of primer as welll complete all as specified.

M&L for Preparing surfaces plastered or unplastered and applying Three coats of white washing on ceiling complete all as specified.

M&L for preparation of new surfaces of any description , not otherwise described over 10 cm width or girth and applying Two coats of synthetic enamel paint over one coat of pink primer on wooden surface complete all as specified.

M&L for preparation of new surfaces of any description , not otherwise described over 10 cm width or girth and applying Two coats of synthetic enamel paint over one priming coat of red oxide/zinc chrome on steel surface complete all as specified.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

S&F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and both face covered with decorative face veneer with lipping/frame to match complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified.

S&F 35 mm 2nd class hard Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.18 mm complete all as specified.

S &F butt hinges, medium weight cold rolled mild steel of size 100 mm size complete all as specified.

S&F 150 mm long aluminium anodised tower bolt complete all as specified.

S&F in 150mm long aluminium anodised handle extruded section complete all as specified.

S&F in 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified.

S&F 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified.

M&L for roof treatement comprising the following stages :-(a) Applying evenly a coat of bituminous primer conforming to IS-3384 @ 0.40 ltr per sqm over and including 10 mm thick cement mortoar (1:4) and surfaces finished even and smooth without using extra cement all as specified . (b) Second coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg/Sqm . (c) Third layer of APP modified polmeric membrane centre core of 20 micron HMHDPE outer film 20 micron both sides, thickness 3 mm having weight 2.25 Kg/Sqm. (d) Fourth layer coat of blown type bitumen confirming to IS 702-1988 grade 85/25 @ 1.2 Kg per Sqm. (e) 40mm thick PCC padding in cement concrete 1:2:4 (12.5 mm graded aggregate) finishing even and smooth including cutting V-groove bothway @ 120 cm and filling with mastic bitumen complete all as specified.

S&F bib cock chromium plated, fancy type cast copper alloy,screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or union of 15 mm bore complete all as specified.

S&F 20 mm dia CPVC pipe with SDR 11 concealed fitting on wall/ceiling or laying in floors complete all as specified.

S&F 25 mm dia CPVC pipe with SDR 11 concealed fitting on wall/ceiling or laying in floors complete all as specified.

S&F 25 mm outer dia PP-R Gate Valve (brass inserted as per requirement of the site screwed both ends of pipe and fixed complete all as specified.

S&F PVC connections 15 mm size of length 450 mm with PTMT nuts complete all as specified.

S&F PVC connections 15 mm size of length 600 mm with PTMT nuts complete all as specified.

S&F Chromium plated shower roses 100 mm dia with or without swivel joints , including shower arm 195 mm long with bend of 45 degree with flange for iron pipe 15 mm bore fixing complete all as specified and as directed.

S&F angular stop valves, chromium plated , fancy type , screwed down ,high pressure, with crutch or butterfly handle , screwed both ends for iron pipe of union of 15 mm bore complete all as specified.

S&F stop valves, fancy type,chromium plated with long shank and cup ( concealed type) , screwed down, high pressure,with crutch or butterfly handle, screwed bth ends for iron pipe or for unions and fixed complete all as specified.

S & F 15 mm size chromium plated fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

S & F Vitreous China wash basin, white, flat back, size 550x450mm but including brackets and PTMT waste coupling 32 mm size complete all as specified.

S&F Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including provision of lime concrete bedding(excluding flushing cistern and flush pipe)

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 cm soil complete all as specified.

Removing excavated soil to a distance exc. 50 metre and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified.

M&L for PCC (1:4:8), type D-2 using 40 mm graded crushed stone aggregate in concrete bedding to drain pipes and forming cradles after they are laid and tested for 150 mm bore pipe complete all as specified.

S&F Reinforced concrete pipes class NP2 laid in trenches and jointed as specified of internal dia of pipe 150 mm complete all as specified.

M&L for PCC (1:5:10) type E-2 using 40 mm graded crushed stone aggregate in foundation, filling mass concrete complete all as specified.

M&L for Precast cement conrete solid block masonry (solid block casted in cement concrete 1:2:4 type B1 with using 20 mm graded stone aggregate) exc. 10cm in width and setting in mortar 1:4 complete all as specified.

M&L Rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces and finished surface even & smooth without using extra cement and mixed with water proofing compound complete all as specified & directed. Note:- Water proofing compound shall be measured and paid separately complete all as specified.

M&L for PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in surface channels/ drains, and benching including finishing top of benching even and smooth using extra cement complete all as specified & directed. Note:- Forming fair finished channel shall be measured and paid separately complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified.

Add to or deduct from above item for forming fair finished channels or drains for each 25mm girth or part thereof over or under 30mm complete all as specified. Note:- This item is only for adjustment of rate if applicable .

M&L for PCC 1:3:6 type C-1 using 20mm graded aggregate copings, levelling course water throughs and like including weathering, slighty rounded or chamfered angles and throating including necessary form work complete all as specified.

S & F 10 Ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and low level flush bend 32 mm complete all as specified.

S&F 1000 ltr Rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I , including 20 mm bore Ball brass valves,high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified.

S & F 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

S & F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.

S & F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with suitable arrangement complete all as specified.

S & F 75 mm PVC (SWR) bends any radius complete all as specified.

S & F 75 mm PVC (SWR) bends any radius with access door complete all as specified.

S & F 110 mm PVC (SWR) bends any radius complete all as specified.

S & F 110 mm PVC (SWR) (single T) any equal or unequal complete all as specified.

S & F 110 mm PVC (SWR) vent cowl complete all as specified.

S&F in 32mm bore low or high density polyethylene waste pipes (LDPE) of pressure rating 6Kg/Sqm fixed complete to walls, ceiling or floors etc complete all as specified.

M&L for 75mm outlet diameter UPVC nahani trap, with CP Mild steel grating (with or without hole) including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) using 20mm graded stone aggregate complete all as specified.

Excavating over areas, n exc 1.5 m deep and getting out in soft /loose soil complete all as specified.

M&L for 100mm thick Cement concrete type D- 2,1:4:8 (40mm graded aggregate) complete all as specified.

Supply and laying 80mm thick factory made chamfered edge cement concrete rubberised paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified.

M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified.

M&L for point wiring for one light point controlled by one switch with two single core 1.5 Sq.mm size multistranded FRLS copper conductor PVC insulated cables and one single core 1.5 Sq.mm size green colour PVC insulated,multistranded copper conductor PVC cable as earth continuity conductor,1100 volts grade, complete drawn in and including rigid PVC CONDUIT and conduit accessories,confirming to IS specifications,concealed in wall fixing on ceiling /trusses with suitable clamps , screws etc, including 1.22 mm thick MS terminal boxes with 3 mm thick plastic laminated sheet top cover fixed with cadmium plated iron screws for mounting switches, sockets, fan regulators etc.,including connecting up and testing complete all as specified.

All item as per Ser No 92.00 above but one fan/ exhaust fan point controlled by one switch.

All item as per Ser No 92.00 above but One switch socket out let point 5 Amps on same board

All item as per Ser No 92.00 above but One switch socket out let point 5 Amps on independent board

Ditto all as per item No 92.00 herein before but with 4 sqmm cable for one 3 pin 15 Amp switch socket outlet and using 4 sqmm PVC single core copper conductor cable multistranded as earth wire complete all as specified.

Supply and fixing switch piano flush type 5 Amp single pole, one way complete all as specified.

Supply and fixing for ceiling rose surface bakelite 65 x 50 mm three terminal complete all as specified.

Supply and fixing switch socket combination multipurpose 5 pin 5/15 Amp flush type, universal complete all as specified.

Supply and fixing switch socket outlet combination 2 in 1 3 pin 6 flush type universal complete all as specified.

Supply and fixing lamp holder insulated body with back plate for batten fitting including necessary connection complete all as specified.

Supply and fixing stepped type electronic fan regulator, resistance type complete all as specified.

Supply and fixing powder coated sheet metal enclosures MCB DB, double door, Tripple pole and neutral 6 way 415 Volt fitted with bus bar, DIN channel, neutral link and incoming contact and making good disturbed surfaces of walls including plaster cutting of wall etc complete all as specified.

Supply and fixing powder coated sheet metal enclosures MCB DB, double door, single pole and neutral 4 way 240 Volt fitted with bus bar, DIN channel, neutral link and incoming contact and making good disturbed surfaces of walls including plaster cutting of wall etc complete all as specified.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of Tripple pole and Neutral and current carrying capacity 40 A to 100 A in the DB complete with connection testing and commissioning complete all as specified.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) of Single pole and Neutral and current carrying capacity 32 A to 40 A in the DB complete with connection testing and commissioning complete all as specified.

Supply and fixing MCB SP 6 Amps to 32 Amps 230 Volt complete all as specified.

S&F surface mounting batten tube light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including lamp LED 1x20 Watt,(4 feet) fixed properly on wall surface and connecting complete from ceilling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified.

S&F surface mounting batten tube light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including lamp LED 1x10 Watt,(2 feet) fixed properly on wall surface and connecting complete from ceilling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified.

S&F building security light LED fitting 35 watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant , epoxy powder coated dark graphite grey colour finish and prismatic polycarbonate cover with individual LED lences suitable for including lamp LED 35 watt, fixed / connect properly at directed location on building with IP 65/66 protection complete all as specified.

Supply and fixing bracket for security light fittings of any size made out of GI pipe medium grade 32 mm dia 1.25 mtr length bend to required size and shape including provision of clamps and fittings in position and two coat of aluminum paint over a coat of red oxide primer all as specified and directed including taking down old bracket complete all as specified.

S&F for steel body Exhaust Fan 300 mm sweep, single phase 230 volts AC, 900 RPM four blade with louver shutters complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 2.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr complete all as specified.

S&F Ceiling fan 1200mm sweep 230V with bushless direct current motor (BLDC) with three blade min air delivery 200CPM with service value 6.00 BEE 5star rating ,down rod , canpoy,nut bolt washer etc with all accessories to connect by using cable PVC insulated copper stranded conductor of size 2.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr complete all as specified.

M & L for building earthing complete with galvanised steel earth plate electrode 60 x 60x 6mm burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edged of the plate not less than 1.5 mtr below normal ground level, connected to galavanised iron earth lead by means of bolt, nut, check nut and washer of galavanised iron wire 4mm as earthing lead as shown in Electrical Plate No 3 of SSR Part I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in any type of soil, earth pit in PCC 1:3:6 type C1 using 20mm stone aggreate, funnel, 20mm dia GI medium grade water pipe, 15mm dia GI light grade earth lead protection pipe, CI frame and cover, wire, copper lugs, wire mesh, charcoal or coke and common salt in alterative layer all around the earth electrode compacted thickness 15 cm including excavation and earth work pit cover including disposal of surplus soil to a distance not excessding 50m, complete testing on completion all complete as shown in electrical plate No 3 of SSR Part I 2009 complete all as specified.

Supply and spreding /bedding sand cushoning for cable protection /cover in trenches 08 cm before laying of cable and 15 cm deep over the cable complete all as specified.

Supply and laying un reinforced precast concrete cable cove class LV type 1 flat size 250mmx150mmx40mm complete all as specified.

M & L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 4 core complete all as specified.

M & L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm 2 core complete all as specified.

Material and labour for 40 mm dia galvanized iron tube light grade for cable protection, supporting to poles, plinth protections, road crossing, trenches, footpath etc, complete all as specified including clamps, nut bolt and washers complete all as specified.

M&L for Cutting of road, hard standing,PCC not exc 45 cm in depth and 30 cm in width for laying of cable and making good surface as per site requirement complete all as specified.

M & L for 20mm bore `Medium grade` galvanised tubes with all fitting,fixed complete to walls and ceilings or laid in floors complete all as specified.

M & L for 25m bore `Medium grade` galvanised tubes with all fitting, laid in trenches complete all as specified.

Supply and fixing gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both ends internally IS-778 marked, Class-2 for iron pipe of size 20 mm bore complete all as specified.

S & F of gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both ends internally IS-778 marked, Class-2 for iron pipe of size 25mm bore complete all as specified.

M&L for drilling/tapping of existing pipe line and fixing of suitble size MS clamp having 25 mm dia pipe for jointing of GI tubing complete all as specified.