VELLORE DISTRICT Construction of Two Class Room School Buliding PUPS, Allivaram at Pennathur Town Panchayat For Kaniyambadi Block CFSIDS 2025-26 PACKAGE NO 01

Amount

VELLORE DISTRICT Construction of Two Class Room School Buliding PUPS, Allivaram at Pennathur Town Panchayat For Kaniyambadi Block CFSIDS 2025-26 PACKAGE NO 01

Earth work excavation for foundation in all classes of soils and sub soil to full depth except in hard rock requiring blasting but inclusive of shoring strutting if required for the sides of foundation.

Filling with M sand including cost and coveyance of all materials to work site and all labour charges etc.

Collection and supply of gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc.complete,

CC 1:4:8 mix using 40mm HBG metal including cost and conveyance and all labour charges and materials charges etc,..

CC 1:2:4 mix using 20mm HBG metal including cost and conveyance and all labour charges and materials charges etc,..

Supply and fabrication of steel including cost and conveyance and all labour charges etc. complete.

Reinforced cement concrete 1:1.5:3 mix using 20mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete

Above Base

Supplying and errecting for sides & soffits including supports and strutting upto 3.29m height for plane surface in all floors including cost and conveyance and all labour charges etc.

column

Varandah L & R Bottom

Brick work in CM 1:5 mix using country bricks including cost and conveyance and all labour charge etc.,

Above Basement

Providing and constructing 110mm thick (Plus or minus 5mm) brick masonry in cement mortar 1:3 for partition walls using well burnt best quality bricks including supplying and laying 1 No 6mm dia MS bars at every fourth layer including scaffolding curing cost of reinforcement etc. all complete as per specifications and drawings as directed by the Engineer in-charge.

Manufacturing, supplying and fixing of Steel doors with following specification.MS angle of size 40x40x6mm at 3.5 kg/m used for outer frame and MS Angle of size 35x35x5mm at 2.6 Kg/m for the shutter frame. Stiffeners with 32x6mm at 1.5 Kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18 G CR Sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50kg/m MS Flat on the rear side of the door, sandwiching the CR Sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter. 300mm length of hinges 2Nos, for shutter is provided.6 Nos. of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door.Tower bolt 2 Nos. at the top provided

Steel door

Fabricating, Supplying and fixng in position of steel sheeted windows ( Three Leaves) with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm

Fabricating, Supplying and fixng in position of steel sheeted windows ( Three Leaves) with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS Flat at 0.70kg/m at 3 Nos. for each shutter and additional diagonal stiffners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly.2 numbers of sturdy hinges and one number of handle-cum-latch of special type made with 18x5mm MS flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adustable stay made out of 18 x 5mm at 0.70 kg/ m MS flat of lenght 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 120mm length spliced at the ends are welded to the outer frame of the window by using MS flat of 18x5mm at 0.70kg/m, welded to the shutter at two place equivalent from each from top and bottom of the shutter.An MS square bar of 12mm size is welded to the inner face of the window at an equal interval not exceeding 100mm edge between them. All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers.All sections should be in confirmed with IS 7452/1990.The cost includes cost of all materials, labour charges and other incidental charges, etc., complete

Steel window

Finishing the top of roof with one course of Solar Reflective ceramic tiles (Required design) of size 305x305x25 mm thick of approved quality and colour laid in CM 1:3, 12mm thick and pointed with tile grout(Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint,curing etc., complete complying with satandard apecification and as directed by the department officers.(The make and brand of the tiles should be got approved by the Executive Engineer before use on works) PWD Data (observed)

Plastering with cement mortar 1:3, 10mm thick including cost and conveyance and all labour charges etc.

Plastering with cement mortar 1:5, 12mm thick including cost and conveyance and all labour charges etc.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification

Floor finishing with granolithic CC 1:2:4 thickness of 25 mm including cost and conveyance of all labour charges

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete). The Putty shoule be got approved by the Executive Engineer before use on work

Colour washing two coats with approved plastic emulsion paint inlcuding cost and conveyance and all labour charges etc,..completed..

Colour washing two coats with approved Distember paint inlcuding cost and conveyance and all labour charges etc,..completed..

Painting with two coats over new iron work using synthetic enamel paint including all

Supply and fixing of cuddapah slab to cubboards including all labour charges etc complete

Supplying and fixing PVC Rain water down fall pipes of following dia meter etc., complete.

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fitt

Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on wor

Electrification

Provision for Light point SD.18

Provision for Fan point SD.18

Supply and fixing of 48" ceiling fan SD.112

Provision for Plug point SD.36

Supply and fixing of Tube light Fitting SD 88

Supply and fixing of Bulk head fitting SD.83

TNEB METER BOARD 3 phase

16Amp DP Switch SD.142

25mm GI Service Pipe SD.70

7/20 Copper Wire SD.64

Rainwater harwesting

Provision for Shoe Rack

Magnetic green board

Provision For Nameboard Charges

GST Amount for providing service to Government contract works for the above construction works. { GST amount is the Total GST amount for total overall quoted amount above this row in column "BB" for all works in this package}

GOPI ENTERPRISES (BID ID -1399541)