Laying of underground cable network with terminations in the area of DGVCL under Olpad Sub Division under Rander Division on ARC basis under S.I. & D.I.S.S. Scheme.

Schedule-B for ARC for Erection and labour work of supply, laying, testing & commissioning of 11/22 KV

Underground XLPE cable (XLPE cable will be supplied by DGVCL) with cable end termination & straight

through jointing kit (To be supplied by contractor) on ARC basis under S.I & D.I.S.S Scheme for Olpad sub

division under Rander division and if required work to be carried out at other sub division under Rander

Item Code Description Unit FY 2024-25

Labour charge for excavation of cable trench of

400mm width x 1200mm depth, in any type of

soil for laying of cable of size up to 240 mm2

(For additional cable 200 mm additional width

shall be considered i.e. half trench length is to be

Labour charge for excavation of cable trench of

600mm width x 1200mm depth, in any type of

soil for laying of cable of size up to 240 mm2

(For additional cable 200 mm additional width

shall be considered i.e. half trench length is to be

Labour charge for excavation of cable trench of

400mm width x 1500mm depth, in any type of

soil for laying of cable of size up to 240 mm2

(For additional cable 200 mm additional width

shall be considered i.e. half trench length is to be

Labour charge for laying of 11kV / 22 kV XLPE

Cable of size up to 240 mm2 & preparation of

sand layer 100mm thick, in the cable trench &

covering the cable with 150 mm dia (Inner),

thickness 25 mm, 1.0 meter long RCC half

round muffs and providing and fixing of 4inch

width yellow colour polyethylene tape with

printing "CAUTION ELECTRIC CABLE BELOW"

at 0.75 m depth from ground surface after laying

cable in trench. This will provide indication that

electric cable is passing underground so as to

protect cable from mechnical injuries, refilling the

same, as per Instruction of Engineer in Charge

Labour charge for horizontal drilling using

Auger machine without damage to surface road

at max 2.0 mtrs depth & putting of 6.11 kg/cm2

class-4,Green color, 110mm O.D. , 8.5mm

thickness H.D.P.E. pipe confirms to IS 4984-

1987(3rd revision) and BIS certification and

laying of 11KV/22KV XLPE cable of size up to

240 mm2 in HDPE pipe, as per Site Condition

(excluding cost of pipe). The detail map obtained

from HDD machine and excell sheet(hard and

soft copy) indicating the respective depth and

distance from adjacent landmark for each

segment for HDD is must required to be

submitted. HDD to be carried out at depth

mtrs to 2.0 mtrs as per site conditions and as per

instruction of EIC.

Labour charge for horizontal drilling manually

without damage to surface road at max 2.0 mtrs

depth & putting of 6.11 kg/cm2 , class-4,Green

color, 110mm O.D. , 8.5mm thickness H.D.P.E.

pipe confirms to IS 4984-1987(3rd revision) and

BIS certification and laying of 11KV/22KV XLPE

cable of size up to 240 mm2 size, as per Site

Condition (excluding cost of pipe). The detail map

and excell sheet(hard and soft copy) indicating

the respective depth and distance from adjacent

landmark for each segment of cable to be

submitted. Drilling to be carried out at depth

Minimum 1.2 mtrs to 2.0 mtrs as per site

conditions as per instruction of EIC.

Supply of 6.11kg/cm2 , class-4,Green color,

110mm O.D. , 8.5 mm thickness H.D.P.E. pipe

7 9925000007 confirms to IS 4984 and BIS certification for Meter

laying of underground 11KV / 22KV XLPE cable

up to 240 mm2 size.

Labour work for RCC concreting on disputed

location and repairing of damage portion of road

8 9925000008 crossing for the work carried out for roads CMT

crossing as well as concreting & muffing of

ploes including all materials (1:2:4)

Providing & fixing concrete stone route marker of

300 mm width x 150 mm thick x 650 mm

height embedded in earth at least 300 mm below

& 350 mm above ground level respectively at

distance approx 50 meters along the length of

cable. The RCC concreting (1:2:4)(all necessary

maeterials will be in bidder's scope) of route

marker is to be carried out 300 mm width x

9 9925000009 mm thick x 300 mm below ground level as per No.

instruction of EIC. The route marker should be

with name of company with approved yellow

colour-DGVCL. The distance from marker to

cable and cable depth with feeder name etc.,

marked with arrow sign is to be painted on it.The

route marker is to be fixed at location near to any

fixed permanent location (not necessary to fix

exact on top of cable) as per instruction of EIC.

Erection of D.P. (double pole) structure using

9 / 11 Mtr. RSJ pole with cable connection

arrangement along with fitting of necessary

fabrication for 11KV cable including excavation of

pit & refilling of earth as per instruction of EIC.

(Exclusive of concreting & muffing of poles)

Erection of Single pole structure using 9 /

Mtr RSJ pole with cable connection arrangement

along with fitting ofnecessary fabrication for

11KV/22 KV cable including excavation of pit &

refilling of earth as per instruction of EIC.

(Exclusive of concreting & muffing of poles)

Erection of D.P. (double pole) structure using

8.0 Mtr. PSC pole with cable connection

arrangement along with fitting of necessary

fabrication for 11KV cable including excavation of

pit & refilling of earth as per instruction of EIC.

(Exclusive of concreting & muffing of poles)

Erection of Single pole structure using 8.0 Mtr

PSC pole with cable connection arrangement

along with fitting ofnecessary fabrication for

11KV/22 KV cable including excavation of pit &

refilling of earth as per instruction of EIC.

(Exclusive of concreting & muffing of poles)

Labour charge for erecting of 11kV / 22 kV XLPE

cable of size up to 240 mm2 on DP Structure

14 9925000014 with fixing of 02 Nos polymer cleats on top Per Job

and middle part.Polymer cleats, nut bolts etc.

fixing material to be provided by contractor.

Providing & fixing of 6.11kg/cm2 , class-4,Green

color, 110mm O.D. , 8.5mm thickness H.D.P.E.

pipe confirms to IS 4984 and BIS certification

on the erected DP structure for the mechanical

protection of cable by inserting the cable inside

15 9925000015 HDPE pipe. The HDPE pipe shall be erected in Per Job

such a way that 300mm shall be below the

ground level and the rest 2700 mm shall be

supported on the DP Structure with 01 No

Polymer cleat.All materials including polymer

cleat and Nut bolt to be provided by contractor.

Providing and fixing of pipe type earthing from

80 mm dia class-B GI pipe with pit to be filled

with salt & coke and construction of chamber as

per DGVCL Drg. No. dg /100 for DP and cable.

The earthing pit should be joined with cable by

G.I. strip of size 1” width & 2 mm thick. All

material GI pipe, Coke, Salt etc will be supplied

Supply & fixing of heat shrink type end

terminations (outdoor) for upto 11kV 3C x

mm2 size XLPE cable as per DGVCL technical

Supply & fixing of heat & shrinkable end

terminations (outdoor) for upto 22 kV 3C x

mm2 size XLPE cable as per DGVCL technical

Supply & fixing of heat shrink type end

terminations (indoor) for upto 11kV 3C x

mm2 size XLPE cable as per DGVCL technical

Supply & fixing of heat & shrinkable end

terminations (indoor) for upto 22 kV 3C x

mm2 size XLPE cable as per DGVCL technical

Supply & fixing of heat shrinkable straight

21 9925000021 through joint for upto 11kV 3C x 185 mm2 size No.

XLPE cableas per DGVCL technical

Supply & fixing of heat shrinkable straight

22 9925000022 through joint type for upto 22kV 3C x 185 mm2 No.

size XLPE cable as per DGVCL technical

Labour charge for excavation of 2100mm long x

1200mm wide x 1200 mm deep joint pits for

installation of 11kV / 22kV Straight through

joints as per instruction of engineer-in-charge &

covering the cable with 150 mm dia (Outer),

thickness 25 mm, 1.0 meter long RCC half

round muffs & refilling same as per instruction

Providing and fixing of insulating bus bar, made

from 11KV/22KV XLPE cable after removal of

semi conducting layer and applying of PVC heat

shrinkable anti-tracking core insulating tubing

(1.1KV), on both end terminal using Aluminium

long barrel heavy duty up to 240 sq mm lugs,

24 9925000024 Aluminium bus connector. Taping with PG- clamp No.

for bus conductor as per drawing and as per

instruction of EIC. The Alluminium lugs and PG

clamp shall be covered with 11KV/22KV HT

insulating tapes.(11KV/22KV XLPE cable will be

in scope of DGVCL while all other materials will

be in bidder's scope)

Testing of cable at various points and

commissioning the feeder as per instruction of

engineer-in-charge.Test result shall be submitted

by contractor with bill.

Preparation and submission of 6 (six) copies, of

complete layout drawings with GIS mapping as

26 9925000026 per actual cable routing showing road crossing, Set

HDPE pipe sleeving, jointing locations, markers

Providing and fixing of Sign Board at junction

point Made out of 2 mm aluminium sheet size

750x300 mm (2.5 x 1ft) rectangle, as per design,

pre treated with phosphate process and acid

etching coated with one coat of epoxy primer and

two coats of best quality paints, refloctrorised

with Hi-Intensity retro – reflective sheeting as per

the latest and frame fabricated from suitable size

iron angle. The Sign Board is to be fixed on the

base prepared from channel and bracing angles

which is grouted by means of cement concreting

of 1:2:4 for size of 300 mm dia x 800 mm height

(500 mm to be grouted in ground). The details to

be displayed on sign board will be given by In-

charge Engineer.

(a) Hi intensity Micro prismatic Grade

Providing and fixing of Sign Board (Danger

Board) on Distribution Transformer Centers

Made out of 2mm aluminium sheet size

300x300mm (1x1ft) as per design, pre treated

with phosphate process and acid etching coated

with one coat of epoxy primer and two coats of

28 9925000028 best quality paints, refloctrorised with Hi-Intensity No.

retro-reflective sheeting as per the latest and

frame fabricated from suitable size iron angle.

The Sign Board (Danger Board is to be fixed at

the location as per instruction of In-charge

(a) Hi intensity Micro prismatic Grade

Providing & fixing of aluminium tag of size

mm (L) x 75 mm (W) from 3 mm aluminium sheet

along with 1.0 mm dia aluminium binding wire for

fixing of aluminium tag near end termination joint

29 9925000029 at DP structure for identifyng the cable. The No.

details of feeder i.e. 11 / 22 KV with feeder name

shound be punched on the tag by letter punch of

size 16 mm as per instruction of In-charge

Supply & fixing of heat shrink type end

terminations (outdoor) for 11kV 3C x 240 mm2

size XLPE cable as per DGVCL technical

Supply & fixing of heat & shrinkable end

terminations (outdoor) for 22 kV 3C x

mm2 size XLPE cable as per DGVCL technical

Supply & fixing of heat shrink type end

terminations (indoor) for 11kV 3C x 240 mm2

size XLPE cable as per DGVCL technical

Supply & fixing of heat & shrinkable end

terminations (indoor) for 22 kV 3C x 240 mm2

size XLPE cable as per DGVCL technical

Supply & fixing of heat shrinkable straight

through joint for 11kV 3C x 240 mm2 size

XLPE cableas per DGVCL technical

Supply & fixing of heat shrinkable straight

through joint type for 22kV 3C x 240 mm2 size

XLPE cable as per DGVCL technical

Installation, Testing and commissioning of

KV,630 A SCADA Compatible, RRL type- 3 Way

36 9925000038 RMU including Two numbers of earthings as per No.

Drawing (material is in bidder's scope) and as per

DGVCL Technical specification.

Installation, Testing and commissioning of

KV,630 A SCADA Compatible, RRLL type-

37 9925000039 Way RMU including Two numbers of earthings No.

as per Drawing (material is in bidder's scope) and

as per DGVCL Technical specification.

Installation, Testing and commissioning of

22KV,630 A SCADA Compatible, RRL type-3

38 9925000040 Way, RMU including Two numbers of earthings No.

as per Drawing (material is in bidder's scope) and

as per DGVCL Technical specification.

Installation, Testing and commissioning of

22KV,630 A SCADA Compatible, RRLL type-4

39 9925000041 Way, RMU including Two numbers of earthings No.

as per Drawing (material is in bidder's scope) and

as per DGVCL Technical specification.

Construction of plinth for 11KV, RRL type-

Way (i.e Two numbers of Isolator & One number

of Breaker) Ring Main Unit as per DGVCL's

technical specification mentioned in drawing no:

Drg. 11kv-01. All required material will be

supplied by contractor.

Construction of plinth for 11KV, RRLL type-

Way (i.e Two numbers of Isolator & Two number

of Breaker)Ring Main Unit as per DGVCL's

technical specification mentioned in drawing

no:Drg. 11kv-02.All required material will be

supplied by contractor.

Construction of plinth for 22KV, RRL type-

Way (i.e Two numbers of Isolator & One number

of Breaker) Ring Main Unit as per DGVCL's

technical specification mentioned in drawing no:

Drg. 22kv-01. All required material will be

supplied by contractor.

Construction of plinth for 22KV, RRLL type-

Way (i.e Two numbers of Isolator & Two number

of Breaker)Ring Main Unit as per DGVCL's

technical specification mentioned in drawing

no:Drg. 22kv-02.All required material will be

supplied by contractor.

Modifications e.g.Providing and fixing of Terminal

protectors i.e. Re-use able boot (HT Side

11/22KV, LT Side 1.1KV) including 11/22 KV

insulating taps and L.T.(1.1 KV) insulating taps

,Busbar, Tapping from Bus Bar (11/22 KV XLPE

cable) through P.G. Clamp for H.T. Jumper to

D.O. Fuse to bushings of Transformer Center,

providing & Fixing of jumper and providing &

fixing of Heat Shrinkable Anti Tracking Core

Insulating Tubing (Insulation Level 11/22 KV) in

H.T. jumper , Clamping arrangement of cable

44 9925000046 support frame on both side of existing Over Head No.

type Distribution Transformer to utilize in Under

Ground cable network as per drawing & as per

instruction of Engineer incharge. All live parts

i.e. PG-Clamp, connections of D.O.fuses, HT

bushings etc . shall be covered with fixinng of

11/22 KV HT insulating tapes. ( 11/22 KV XLPE

cable will be in scope of DGVCL while all other

materials will be in bidder's scope ) .

Laying of any size of 11/ 22 KV XLPE /PILC

45 9925000047 Per Cable Per Mtr

Cable in redaymade trench or in open space

Labour charges for Lying of O/H XLPE cable pole

Supply of 150 mm dia (Inner), thickness 25 mm,

1.0 meter long RCC half round pipe

In Words :-- Thirty Lakh Rupees Only

% Above / Below of Estimate Amount

Stamp & Sign of Contractor

Executive Engineer (O&M)

DGVCL,Rander Division