Project of National Institute of Fashion Technology at Kangra

Amount

Excavation in hilly area in all heights and depths and in all kind of soil by manual/mechanical means including saturated soil comprising of ordinary soil, soft rock, hard rock, chiseling, wedging out of rock (where blasting is prohibited) and their intermediate classification of soil, setting out true to the required lines, grades, width cutting and trimming of side slopes and level as shown in the drawing and as directed by engineer-in-charge at site according to the MORD technical specification clause 302, 304 and 1603 and sorting out useful materials and stacking the same in all leads and lifts in acquired width of road and transportation of unuseful material for filling in road ways, camber, embankments for grade improvements and disposal of all useful material in acquired width of the road or on approved dumping sites through all modes of transportation including head load or animal transport or mechanical means along with its leveling, fine dressing and carriage of machineries, materials, tools, equipments and safety measures and incidentals necessary to complete the work by mechanical means and/labour if required. Recovery of stone at the rate of 300/- (Rupees Three hundred) only per cubic metre shall be effected from the contractor running bills on pro-rata basis as per actual quantity executed. Any loss to the public, private property during the course of execution shall be the absolute responsibility of the contractor which shall have to be compensated by him in all cases.

Providing and laying mechanically mixed and vibrated plain cement concrete in open foundation for all type of structure using plain cement concrete nominal mix 1: 4: 8 (one cement isto four sand isto eight graded crushed stone aggregate 40mm (forty millimeters) nominal size including curing complete including the cost of form work in or under water including pumping or bailing out water, dewatering, removal of slush as required at site which may arise at the time of laying under water complete for all heights/depths as per drawing and MORD technical specification section 800, 900 and 1200 and as per the direction of the Engineer-in-Charge and carriage of material within all leads, lifts and other incidental . The rate including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Half brick masonry with common burnt clay FPS (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:3 (One cement isto Three Sand) and as per direction of the Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals. The rate includes sale tax, octroi, royality, malkana, toll tax, GST, labour cess or other taxes imposed by the Government.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in cement mortar 1:6 (One cement isto Six sand) and as per direction of the Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals. The rate includes sale tax, octroi, royality, malkana, toll tax, GST, labour cess or other taxes imposed by the Government.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement and as per direction of the Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals. The rate includes sale tax, octroi, royality, malkana, toll tax, GST, labour cess or other taxes imposed by the Government.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size). and as per direction of the Engineer-in-Charge including carriage of material within all leads and lifts and other incidentals. The rate includes sale tax, octroi, royality, malkana, toll tax, GST, labour cess or other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters)thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering, strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm.(Three decimal fifteen milimetre) thick welded with angle iron in frame 30x30x5mm.,(Thirty into thirty into five milimetre)so as to give a fair finish including centring,shuttering, strutting and propping etc. with wooden battens and ballies complete upto all heights/ depth of propping and centering below supporting floor to ceiling upto all height and removal of the same for insitu- reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like including carriage of material within all leads, lifts and other incidentals. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters)thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimeters),so as to give a fair finish including centring, shuttering, strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers, girders lintels, sides, and soffits of beams, beam, hunchings, cantilevers, bressumers and lintels upto all depths within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing form work with steel plates 3.15mm. (Three decimal one five milimetre) thick welded with angle iron frame 30x30x5mm (Thirty milimetre into thirty milimetre into five milimetre ).,so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all heights/depths of propping and centering below supporting floor to ceiling upto all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Edges of slab and breaks in floors and walls under any thickness, the rate is inclusive of all leads and lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing Tor steel reinforcement for Reinforced cement concrete work including bending, binding and placing in position and including cost of binding wire complete for all floor level including carriage of materials within all leads and lifts and other incidentals as per the direction of Engineer-in-Charge. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

15 mm (Fifteen milimetre) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and /or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1:6 (One cement isto Six sand), as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana and toll tax, GST or any other taxes imposed by the Government.

Probviding 200mm (Two hundred milimetre) wide cast iron Rungs with chequred or ribbed iron dip surface including fixing in manholes with 200mmx200mmx100mm (Two hundred into Two hundred into Onehundred milimetre) cement concrete 1:3:6 (One cement isto Three Sand isto Six graded crushed stone aggregate 20mm (Twenty milimetre) nominal size) and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Supplying and fixing C.I. cover with frame for manholes 455x610mm (Four hundred fifty five into Six hundred ten milimetre) rectangular C.I. cover (light duty) the weight of the cover to be not le4ss than 23 kg (Twenty three kilogram) and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixing soil waste and vent pipes centrifugully cast (spun) iron socket and spigot (S&S) pipe as per IS: 3989 and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixing bend of required degree with access door insertion rubber washer 3mm (Three milimetre) thick bolts and nuts complete sand cast iron S&S as per IS-3989 and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixing cast iron Cowl 100mm (One hundred milimetre) nominal diameter and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying coat of approved steel primer using structural steel et. As required in grating, frames, guard bar, ladder, railing, brackets, gates and similar works and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

15 mm (Fifteen milimetre) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor level including arises, internal angles, chamfers and /or rounded angles not exceeding 80mm (Eighty milimetre) in girth and finished even and smooth with cement mortar 1:4 (One cement isto Four sand) within all leads, lifts, and other incidentals as per the direction of Engineer-in-Charge. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixing soil waste and vent pipes of 100mm (One hundred milimetre) dia sand cast iron S@S pipe as per IS: 1729 and as per the direction of Engineer-in-Charge including carriage of material within all leads and lifts and other incidental. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced cement concrete of Grade M-25 (M-Twenty five) designed mix with cement contents not less than of 400 (Four hundred) Kilogramme per Cubic metre with 20mm (Twenty milimetre) nominal size graded crushed stone aggregate in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing including hauling of materials in all kinds of leads, lifts and other incidental, as per the entire satisfaction and directions of Engineer-in-Charge. The rate including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimeters)thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimeters), so as to give a fair finish including centring, shuttering, strutting and propping etc, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate including of octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Back filling with granular material behind abutments, return walls, wing walls and retaining walls complete as per drawing and M.O.R.D. technical specification Clause 1604.7 and section 300, including carriage of materials within all leads, lifts of materials and other incidentals. The rates including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing weep holes in brick masonry/stone masonry/plain reinforced concrete abutment, wing walls, return wall with 100mm (One hundred milimetre) dia PVC pipe extending through the full width of the structures with slope of 1(V): 20(H) towards draining face complete as per drawing and MORD Technical specification clauses 1206.6 including carriage of material within all leads, lifts and other incidentals. The rate including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

SURUCHI GFUPTA