Repair to plinth protection flooring tiling at SMQ under AGE BR-I GE AF No 2 Jodhpur and repair to internal water supply cleaning of water tanks Inner pockets in AGE BR-I GE AF No .2 Jodhpur

Amount

Taking down cement or cement lime plaster on brick or stone walls etc. including racking out joints hacking for key scrubbing down with water etc. complete all as specified and directed.

M&L for Rendering 15mm thick on fair faces of brick/concrete/stone work in CM 1:4 finished even and smooth without using exctra cement, in any possition complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of any type of work in CM 1:6 finished even and smooth without using exctra cement complete all as specified and directed.

M&L for 5mm thick rendering in CM(1:3) on ceiling/soffit/chajja etc stone/concrete surface in any possition, finish even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound ISI marked as directed by Engineer-in-Charge

M&L for preparation of new plastered or unplastered surface of walls, applying two coat of cement base paint over a coat of cement primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali-resiatant primer and 1 mm thick Birla wall care putty on plastered surrfaces complete all as specified.

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

Demolition of cement concrete of any description and in any position (unreinforced) in ground floors and paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors as directed by Engineer-in-Charge.

M & L 40 mm thick plain cement concrete type B1 1:2:4 ( with 20mm graded aggregate) as in floors finishing cement concrete surface even and smooth with out using extra cement.

M & L 40 mm thick plain cement concrete type B1 1:2:4 ( with 20mm graded aggregate) as in sub base of floor all as specified and directed.

M&L 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection finished surface even and fair without using extra cement all as specified and as directed by Engineer-in-Charge.

M&L 75 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate in sub base of floor all as specified and directed.

M&L 100 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate in sub base of floor all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site and rubbish off the premises as directed by Engineer-in-Charge

M&L for non skid coloured ceramic tiles, 7 to 8 mm thick in floors etc. area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 as directed by Engineer-in-Charge

M&L for non skid coloured ceramic tiles, 7 to 8 mm thick in floors and skirting etc. (square/rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.36 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 as directed by Engineer-in-Charge

M&L for glazed ceramic tiles, coloured, 450x300x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone or brick masonry surfaces as directed by Engineer-in-Charge.

M&L for machine cut kota stone slab flooring 20 -25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigmenst to match the shade of the slab including rubbing and polishing complete including 15 mm screed bed or bedding layer in cement mortar 1:6 as directed by Engineer-in-Charge

M&L for kota-stone slab 15 mm thick in riser of steps skirting dado skirting and risers to step set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick renedering in CM 1:4 on stone masonary surfaces as directed by Engineer-in-Charge

M&L chequered cement concrete tiles 25cm x 25cm x 25mm thick with grey cement and pigment, machine pressed, set, jointed and pointed in neat cement slurry in floors including 15 mm thick screed bedding layer in C:M 1:6 complete all as specified and directed

M&L 50 mm thick sand filling under floor or in foundation including watering and condolodation complete all as specified and directed.

M&L for providing and laying 60 mm thick factory made chamefered edge cement concret paver block of M-35 grade with approved colour design & pattern as in footpath parks lawns drive ways or lighttraffic parking etc of required strength thickness & size shape made by table vibratory method using PU mould laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand comapcting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator filling the joints with sand and cutting of paver blocks as per required size and pattern finishing and sweeping extra sand as directed by Engineer-in-Charge

M&L Granite (of any type) work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, win?dow-cills, cooking plat?forms and like in cement mortar (1:4) including point?ing in white cement (1:2) using marble dust with admix?ture of pigment to match with shade of granite over 15 mm thick Screed bed or bedding layer for laying floor finishes in CM 1:4 complete all as specified and directed.

Demolition of brick work or stone masonary built in cement mortar complete all as directed.

M&L brick work with fly ash old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 all as specified.

Taking up or down steel tubing 15 mm bore and connections including cleaning for refixing or removing from site.

Taking up or down steel tubing 20 mm bore and connections including cleaning for refixing or removing from site complete all as specified and directed.

Supply and laying 15 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Supply and laying 20 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Cutting chases stone concrete blocks pinning in making good to facing where required and pointing in CM 1:3 to ends or edge of landing steps cills sunshades shelves lintels eytc and cutting chases for conealed water tuibing making good not exceeding 10 cm girth for stone walls all as specified and directed.

S&F in repair 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete(minimum weight 450 gms) complete all as specified and directed.

S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.Minimum weight 450 gms. complete all as specified and directed.

S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cup (concealed type), /(angle type)screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions.

S&F in repairs PVC valveless, syphonic action type, high or low level flushing cistern, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets and connections to pies an fixing of chain and pull, or lever all as specified and directed.

S&F in repairs PVC connection 15 mm size with PTMT nuts of length 450 mm all as specified and directed.

S&F in repairs grating doom 125 mm dia with or without waste hole of PTMT (minimum weight 40 gms) and fixing with gray or white cement all as specified and directed.

S&F in repair for PVC (SWR), 75mm dia of floor trap, with grating including jointing with solvent cement and complete and as directed by Engineer-in-Charge.

S&F in repairs 15 mm bore fancy type bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed Make:- Marc MCT-1020 or equivalent in Jaguar & Co, Parryware & Somany Minimum weight 450 gms.complete all as specified and directed.

S&F in repairs 15 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 142 gms.) complete all as specified and directed.

S&F in repairs 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms.) complete all as specified and directed.

Taking up or down steel tubing 25 mm bore and connections including cleaning for refixing or removing from site complete all as specified and directed.

Supply and laying 25 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Refixing old steel tubing, 15 mm bore, and connections with new or old position (Walls, ceiling, floors, etc.) Note :- Steel tubes obtained from item No. 28.00 above shall be used under this item all as specified and directed.

Refixing old steel tubing, 20 mm bore, and connections with new or old position (Walls, ceiling, floors, etc.) Note :- Steel tubes obtained from item No. 29.00 above shall be used under this item all as specified and directed.

Refixing old steel tubing, 25 mm bore, and connections with new or old position (Walls, ceiling, floors, etc.) Note :- Steel tubes obtained from item No. 5 above shall be used under this item all as specified and directed.

S&F in repairs plastic water closet seat cover white or any colour closed padestrial pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and fixed complete all as specified.

S&F in repairs internal flushing cistern kit, washer, flushing handles etc.

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, complete all as specified.

S&F in repairs grating doom 100 mm dia of PTMT (minimum weight 25 gms) and fixing with gray or white cement all as specified and directed.

S&F in repairs brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union.

S&F in Repairs shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms) ccomplete all as specified and directed.

Disconnecting existing tanks of any description exc. 250 ltrs and n.exc. 500 ltrs capacity and removing from site to store.

Disconnecting existing tanks of any description exc. 500 ltrs and n.exc. 1000 ltrs capacity and removing from site to store all as specified and directed.

Cleaning and removing all scale dirt etc. from water storage tanks by using brush and bleaching powder and from mouth of circulating pipes etc. and writing the date of cleaning and next due date for cleaning of tank using stencil, capacity of tanks exc. 250 liters and not exc. 500 liters complete all as specified and as directed.

S&F 500 litres (ISI marked) capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore plastic ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms) all as specified and directed.

S&F 1000 litres (ISI marked) capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore plastic ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms) as directed by Engineer-in-Charge

S&F in repairs, 15 mm bore bib tap, standard of PTMT, any colour screwed for iron pipe and fixed (minimum weight 15mm – 90 gms) all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks, etc, including cleaning or refixing or removal from site all as specified and directed. (measured overall as fixed along the centre line over fittings and accessories) all as specified and directed.

S&F 75 mm bore UPVC (SWR) pipes type ‘B’, single socketed, in any length with rubber ring joints fixed to walls all as specified and directed.

S&F 110 mm bore UPVC (SWR) pipes type ‘B’, single socketed, in any length with rubber ring joints fixed to wall all as specified and directed.

S&F in repairs PVC (SWR) door bends 110 mm dia with acess door all as specified and directed.

All as per item No. 65.00 here-in-before but 75 mm dia with acess door all as specified and directed.

S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 mtr long flexble tube ABS wall hook including making connections and fixed complete in all respect as specified

S&F in repairs PVC waste pipe of 32 mm/40mm bore of suitable length for WHB/urinal/sink, complete all as specified.

S&F in repairs 15 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe all as specified and directed.

S&F in repairs 20 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe all as specified and directed.

S&F in repairs 25 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe all as specified and directed.

S&F in repairs waste coupling of PTMT for wash basin (half or full threaded) 32 mm bore of discharge pipe,(Minimum weight– 45 gms.) all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long.

S&F in repairs shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minium weight 300 gms) all as specified and directed.

S&F in repairs for toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S&F in repairs 15 mm bore brass chromium plated bib cock two in one with angle cock including fixing to steel pipe or union all as specified.

S&F in repairs brass aluminium anodised towel rail, 20mm dia, D type, 60cm long between flanges all as specified and directed.

S&F in repairs stainless steel soap dish made of stainless steel 1.00mm thick, approximate 150x150 mm fixed to plugs with chromium plated brass screws.

S&F PVC lid of PVC water tank suitable for 500/1000 litres capacity fixing to existing water tank with necessary fixing arrangment at any position all as specified and directed.

M&L for repairs to leakage in existing 15 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mm all as directed by Engineer-in-Charge.

M&L for repairs to leakage in existing 20 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mm all as specified and directed.

M&L for repairs to leakage in existing 25 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mm all as directed by Engineer-in-Charge.

M&L for repairs to leakage in floors of WC/Bath Room/Kitchen by breaking of existing floor and providing new PVC (SWR) floor trap, suitable for type ‘B’ pipes, 75 mm dia of outlet, plain with grating including jointing with solvent cement and making good floor to match with existing floor all as directed by Engineer-in-Charge.

S&F in repairs PVC flush bend pipe 32mm dia for PVC 10 litre flushing cistern suitable for EWC/IWC all as directed by Engineer-in-Charge.

M&L for repairs to leakage of any type by providing M-Seal all as directed by Engineer-in-Charge.

M&L for filling of joints of tiles/WC & WHB corner with white cement area n. exc. 1 sqm each all as directed by Engineer-in-Charge.

S & F in repairs stack clamps out of 50 mm x 5 mm flat iron and 16mm dia round iron stays including bolts and nuts & securing ends of stays to wall or roof for 110 mm bore of pipe complete all as specified and directed.

M&L for Cement patch work on wall/floor etc area n. exc. 1 sqm and depth n exc 15cm each all as directed by Engineer-in-Charge.

M&L for Clear air lock from tank to kitchen,bath,wc and WHB by opening GI pipe/nipple,elbow,socket,union and other possible way etc each all as directed by Engineer-in-Charge.

M&L Renewing Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm in patches, area n exc 5 sq.m. including removing and cleaning old tiles, match with existing surface and set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and incl 15mm thick cement screed 1:6 all as specified and directed.

M&L Renewing Glazed ceramic tiles coloured in vertical surface 300x200x7mm thick in patches, area n exc 5 sq.m. including removing and cleaning old tiles, match with existing surface and set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and incl 10mm thick rendering in CM 1:4 on stone or brick masonry surfaces as directed by Engineer-in-Charge.

M&L in repairs to sink made of stainless steel by providing waste coupling brass, chromium plated of 32 mm with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed 32 mm complete all as specified.

M&L in repairs to sink made of stainless steel by providing waste coupling brass, chromium plated of 40 mm with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed 40 mm complete all as specified.

S&F in repair sink with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410mm x 330 mm x 160 mm and PVC waste pipe of 40 mm bore and of suitable length, complete all as specified.

S&F in repairs sink made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm and PVC waste pipe of 40 mm bore and of suitable length, complete all as specified.

S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, size 580mm x 440mm, white with integral foot rests, including PVC 'P' trap, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish all as specified and directed.

S&F in repairs, EWC vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device fixed complete all as specified and as directed by Engineer-in-Charge

S&F in repairs stainless steel plate rack 0.56mm thick of standard pattern of size 750x600x250 mm complete as directed by Engineer-in-Charge

Amresh Traders

M/S SUA DEVI

psj build solutions and company

GANGADHAN ENTERPRISES

CHOUDHARY CONSTRUCTION CO

M/S IK CONSTRUCTION

M/S JAGDAMBA ENTERPRISES