Remaining work of Providing, Supplying & Installation of SEWAGE Treatment Plant, Drilling of Borewell, Providing & Laying External Drainage and Construction of Wire Fencing for STP at PHQ Khutaliya, Chhotaudepur Dist Chhotaudepur (Including Concealed Electrification) [1st Attempt]

No. InFigure In Words Rs.

1 Designing (hydraulic, process. structural & aesthetic), providing, construction, hydraulic 1.00 Package 12302649.21 Rs.One Crore Twenty Eight

testing,commissioning of Sewage Treatment Plant of Capacity 155000 ltr per day (155 KLD) Lacs Forty Four Thousand

and giving satisfactorily trial run for 3 months of STP consisting of inlet Chamber, Screen Only

chamber, Grit Separator, MBBR (Based on technologies providing attached growth on plastic

media kept suspended in the sewage due to low density of plastic & provided with diffused

air for aeration with tank, Secondary Clarifier, Sludge collection sump, Gravity Sludge

Thickener, Chlorine Contact Tank, Chlorinator room, Sludge Dewatering

Equipment,associated piping work with required valves, gates, drains. Administration Block

cum Laboratory, associated buldings, Laboratory Equipments, inclusive of mandatory spare

parts and instrumentation, etc complete as turnkey jobs with all involved civil, electrical,

instrumentation and mechanical works inclusive of following items, units as per detailed

specifications for civil, electrical, instrumentation and mechanical components with all duties

and taxes etc. commplete to achieve BOD<10ppm,TSS< 10ppm, Biological TN < 10ppm &

PO4 < 2ppm to get recyclable quality of water for industrial/agricultural purposes. The

Coagulant Desing System is mandatory for chemical phosphorus removal. All units shall be

interconnected with administration building by Suitable or RCC overhead walkways.If so

required for the complete working of the STP and have it approved by GSPHCL.All the

materials & componant of STP Shell be of approved brand & make by GSPHCL Only.

Min. freeboard of 0.3m shall be maintained unless otherwise asked for 0.5m stipulated for

specific units.

A PRIMARY TREATMENT

1.1 Bar screen Chamber : Supply, installation, testing & commissioning of 2 Nos. SS-

304 Perforated, Screens with suitable lifting arrangement to be fitted with in Bar Screen

Chamber as per STP Manufacturer's design.

1.2 Oil & grease Chamber : Supply, installation, testing & commissioning of Manual

overflow type Oil Removal trap for removal of Oil & Grease from Chamber.

1.3 Collection cum Equilization tank: Tank will be in RCC _ Civil Contractor Scope and the

tank shall have Retention time of Minimum 8 Hours. Course Bubble aeration will be provided

in the tanks.Design included and to be approved by department GSPHC.

1.4 Raw Sewage Transfer Pump :Supply, installation, testing & commissioning of non-

clogging submersible pumps complete with all accessories, motor of required capacity.

Delivery header with check valve, level controller (with wiring) to control the level of

sump automatically.

No. of pumps: 02 Nos. (1 Working + 1 Standby).

B SECONDARY TREATMENT

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

2.1 Process Tanks : Material of construction shall be in MS + FRP : MS sheet thickness 6.0 mm

and Internal FRP lining shall be 2.0 mm. Outside Epoxy Painted.

2.1.1. Anoxic Tank : As per STP Manufacturer's design

2.1.2. Aeration Tank : Aeration Tank shall have suitatble MBBR Media As per STP

Manufacturer's design. Fine Bubble aeration shall be provided with Air Blower (No of

Blowers : 1 Working + 1 Standby)

2.1.3 Tube Settler \ Lamella Settler : Tank with Tube Deck media \ Lamella Plates and

Recirculation Pumps (No. of pumps: 02 Nos. (1 Working + 1 Standby)) As per STP

Manufacturer's design.

2.1.4 Chlorine Contact tank: As per STP Manufacturer's design. Chlorine dosing shall be

provided with tanks and dosing Pumps (No of Pump : 01 No and No of Tank : 01) for

disinfection Purpose.

2.1.5 Sludge Holding Tank: Tank As per STP Manufacturer's Design. Filter press of suitable

capacity along with Feed Pump ((No. of pumps: 02 Nos. (1 Working + 1 Standby)) as per STP

Manufacturer's design.

C TERTIARY TREATMENT

3.1 Filter Feed Pump : Supply, installation, testing & commissioning of pumps complete with

all accessories, motor of required capacity. Delivery header with check valve, level controller

(with wiring) to control the level of sump automatically. No. of pumps: 02 Nos. (1 Working +

1 Standby).

3.2 Multigrade Filter: Supply, installation, testing & commissioning of Filter complete

with all accessories, Isolation Valves, Vessel media and Piping

3.3 Activated Carbon Filter: Supply, installation, testing & commissioning of Filter

complete with all accessories, Isolation Valves, Vessel media and Piping

3.4 Treated Water tank: Tank will be in RCC _ Civil Contractor Scope and the tank shall have

Retention time of Minimum 8 Hours. Design of tank is included which to be approved from

GSPHC Structure department.

D 4.0 Control Panel for Sewage Treatment Plant & Cabling Work :

4.1Supply ,Installation ,Installation & Commissioning of Common control panel

(compartmental type) and Cabling for all electrical items like sewage transfer pumps,

air blowers, filter feed pumps, sludge removal pump as well as dosing system.(Details

Attached Below)

4.2 SLD & A Drawing of panel shall be approved by Executive Engineer (Ele.)Panel

Manufacture Shall be approved by EIC as per Tender specification and make list

5.0 Inter Connecting Pipe Work within Battery Limit : 01 Set. Sewage Pipe line Shall be UPVC.

Air line shall be MSEP. Submerged air lines shall be in UPVC. Clear Water shall be in UPVC.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

(1) All Civil works finished with water proofing, plaster, Outside & Inside colour as per

GSPHC list, structure duly tested for leak-proofing, plant room flooring, pumps foundations

etc. and related S.S/MS/CI works such as supply and fixing of handrails, manholes, gratings,

grills, doors, vents, footrests etc. shall be in the scope of the Main Civil Contractor.

(2) All Civil Tanks shall be constructed in RCC as per STP manufactures drawing &

STRUCTURAL Design.Design to be approved by structure department of GSPHC

(**All PCC work Should be in M-150 & RCC Work should be M-300. Mix design to be done by

(3) If anything required to achieve the mentioned parameters and completing treatment

process shall be in STP Manufacturer's scope.

B. Chemical & Consumable Charges for Comprehensive (all inclusive) annual maintenance

service contract of the above STP system as per the terms and conditions of the tender, This

shall be applicable after Defect Liability Period of One year. Total -3Yrs.

C. Operation of Sewage Treatment Plant Charges for providing manpower for operation of

STP at site as per the terms and conditions of the tender . The charges shall be

applicable after handing over of the system.Including cost of operater, Periodical

checking of the plant, periodical testing of treated water with submission of reports,

oiling, greasing, routine and preventive maintenance of electrical Items, consumables,

chemicals, disposal of dried sludge as per direction of engineer in charge.

Total Time Period -3 Yrs.

Manpower : 3 Operator (8 Hour shift) and 1 Helper

F Rate include all cost of material,Labour and require machineries involved in the item.In all

operation describe above for complete above item.

G Estimate offer should be including Collection tank,Treated water tank and all civil work

finished with water proofing ,treatment as require,plastering ,colour work as per

GSPHC,Structure duly tested for leakproofing

,Plant room flooring ,Pump foundation etc.and related S.S/M.S/CI work such All items

engineer incharge.

H Electrical Supply panel,Power and control cabling.

Electric Control Panel & Cables with automation, audio Visual alarm. (As per Venders design

A) Power and control cabling between panel and electrical motors, instruments.

All power cables up to 4 mm2 will be of Copper Armoured conductor, whereas above

4 mm2 will be of Aluminium conductor. Perforated metallic Cable tray with supports will

be provided to lay the cables.

B) All instrument cables will be of Copper conductor.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

I (C)SITC of CPRI approved makeI IP 66 with Double door Compartment type Electric control

panel mounted on the Stand for Semi automatic operation of pumps comprising incoming

MCBB, digital VAF meter switches, over load and under voltage protection devices, single

phase preventers, Reverse phase sequence, MCB and DOL /Stat Delta starter for each

motor, indicating Lamp etc, dry suction cut off, all complete. 1 No. Panel

comprising:

• Compartment type, with 2mm sheet metal for Outer body & door & 1.5 MM sheet metal for

partition.

• Cubical type

• Floor mounted with 1.5 feet height supporting legs with necessary foundation as per site

requirment

• Cable bottom/Top entry(As per Site Situation)

• All cables inside the panel will be of Copper conductor.

• Incoming power control switch.

• Ammeters voltmeters Frequency (VAF) phase indicating lamps,

• MCB and starters.

• 2 Nos. automatic level controllers for actuating raw effluent and Filter Feed pumps.

J (D) Automation for Pump operation :

System to start manually/automatically at every start, the other pump shall cut in

There shall be audio visual alarm in case any pump/blower fails to starts// trip.

Proper name plates & marking will be provided on the panel doors.

Programmable Control System for the following logic:

i) System to start manually/automatically

ii) At every start, the other pump shall cut in

iii) Audio visual alarm in case any pump/Blower fails to starts.

iv) Both the pumps & Blowers will be in operational but with one remaining standby at any

particular moment.

K E) Local Push bottom.

F) Armored cabling from our panel to motor starters and earth pits (in civil).

G) Necessary earthing chamber(Civil Job)

H) Earthing to panel connectivity to 25 x 6 mm GI patti & Panel to motor/ Machine

connectivity 10 mmcopper wire.

Control panel to be designed for semi-auto operation of STP. (i.e. LLC based operation

for raw and filter). Pressure gauges will be provided on delivery main for pumps, blowers

and vessels. Agency shall complete the STP system and put in working order.No Extra

payment shall be done for electrical item mention in above description.

Mode of measurements & payments The rate shall be for a unit of one set.

Excavation for foundation in Dense and Hard Soil from upto 1.5 mt depth including sorting 673.00 Cum . 159.30 Rs. One Hundred Fifty Nine &

2 out and stacking of useful materials and disposing of the excavated stuff upto any Lead and Paise Thirty Only

Excavation for foundation in Hard Murrum Soil upto 1.5 mt. depth including sorting out and 1043.00 Cum . 272.60 Rs. Two Hundred Seventy Two

3 stacking of useful materials and disposing of the excavated stuff upto Any Lead & Paise Sixty Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

Excavation for foundation in Hard murrum from 1.50m to 3.0m depth including sorting out 747.00 Cum . 291.14 Rs. Two Hundred Ninety One

4 and stacking of useful materials and disposing of the excavated stuff upto Any Lead & Paise Fourteen Only

Filling in Foundation and Plinth with Available soil or murrum in layers of 20cms. thickness 1223.00 Cum . 136.11 Rs. One Hundred Thirty Six &

5 including watering, ramming, consolidating and dressing etc.complete Paise Eleven Only

Providing & laying Cement Concrete 1:4:8 ( 1 cement : 4 coarse sand : 8 graded stone 68.00 Cum . 2753.58 Rs. Two Thousand Seven

6 aggrigates of 40 mm nominal size) curing complete including cost of formwork in Foundation Hundred Fifty Three & Paise

and plinth. Fifty Eight Only

Provinding and laying Controlled cement concrete M-250 and finishing smooth with curing 7.00 Cum . 6060.00 Rs. Six Thousand Sixty Only

etc. complete including the cost form work but excluding the cost of reinforcement for RCC

work in COPING for any cross sectional area of column. Providing and Mixing Plasticiser in

cement concrete as per mix design including rate of labour,material etc.as per direction of

Engineer in charge.

Providing TMT Bars Fe -500 D Reinforcement for RCC work including cutting, bending, 650.00 Kg 76.52 Rs. Seventy Six & Paise Fifty

binding and placing in position etc.complete for all floors.Steel must be used Approved Two Only

Material list of GSPHCL.

BRICK WORK using common burnt clay building bricks having crushing strength not less 62.00 Cum 4237.60 Rs. Four Thousand Two

than 35 Kg./Sq. cm. In Foundation & Plinth in cement mortar 1 : 6 ( 1 cement : 6 coarse sand ( Hundred Thirty Seven & Paise

Conventional Bricks) for Foundation & Plinth. Sixty Only

Provinding 15 mm thick cement PLASTER in single coat on brick or concrete wall for interior 60.00 Smt. 229.09 Rs. Two Hundred Twenty Nine

plastering and finished even and smooth in C.M. 1:4 ( 1 cement : 4 sand ) including finishing & Paise Nine Only

with floating coat of neat cement slurry at GROUND FLOOR.

Providing 20mm thick SAND FACED cement plaster on walls above ground level consisting 170.00 Smt. 350.48 Rs. Three Hundred Fifty &

12mm thick backing coat of C:M 1:3 (1 cement; 3 sand) and 8mm thick finishing coat of C:M Paise Forty Eight Only

1:1 (1 cement; 1 sand) etc. complete for any height.

Providing & fixing Concealed Center Point to wall celing & floor CPVC (SDR-13.5) PIPE 100.00 Rmt. 251.31 Rs. Two Hundred Fifty One &

having National Sanitation Foundation (NSF) seal For Portable Water of 25 mm. dia. nominal Paise Thirty One Only

12 bor tube fitting and clamps including making good the wall, ceiling and floor etc. Complete

Providing & fixing Concealed Center Point to wall celing & floor CPVC (SDR-13.5) PIPE 540.00 Rmt. 443.29 Rs. Four Hundred Forty Three

having National Sanitation Foundation (NSF) seal For Portable Water of 40 mm. dia. nominal & Paise Twenty Nine Only

13 bor tube fitting and clamps including making good the wall, ceiling and floor etc. Complete

Providing & fixing Concealed Center Point to wall celing & floor CPVC (SDR-13.5) PIPE 200.00 Rmt. 654.04 Rs. Six Hundred Fifty Four &

having National Sanitation Foundation (NSF) seal For Portable Water of 50 mm. dia. nominal Paise Four Only

14 bor tube fitting and clamps including making good the wall, ceiling and floor etc. Complete

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

Providing & fixing Concealed Center Point to wall celing & floor CPVC (SDR-13.5) PIPE 150.00 Rmt. 1312.94 Rs. One Thousand Three

having National Sanitation Foundation (NSF) seal For Portable Water of 65 mm. dia. nominal Hundred Twelve & Paise

15 bor tube fitting and clamps including making good the wall, ceiling and floor etc. Complete Ninety Four Only

Providing, supplying and fixing Corrugated DWC HDPE Pipes of Class SN8 Structured Wall 200.00 Rmt. 396.00 Rs. Three Hundred Ninety Six

polyethelene Piping systems (Pipe with online/offline coupler and elastomeric sealing ring) Only

with non-smooth External Annular Corrugated and Smooth Internal Surfaces (Double Wall)

for non-pressure underground Sewerage & Drainage application as per EN:13476-3 including

all local and central taxes, transportation, freight charges, octroi, inspection charges, loading,

unloading, conveyance to the departmental stores etc. complete. (150 mm ID Dia) Including

Lowering, laying and jointing of class SN 8 structured wall ( External Annular Corrugated &

Smooth Internal surface) Polyethylene Piping and fittings with the help of coupler ( on line /

off line ) attached with one end of pipes, sliding over the elastomeric sealing rubber ring

placed on the specified valley of the corrugation at the spigot end, lowering the same into the

16 trench, laying on the lower bedding (constructed at bottom of trenches) at prescribed

gradient,depth & alignment ,testing the water tightness of the joints, ensuring the continuity

tests of specified pipe segments etc. complete as per drawing,specifications & detailed

engineering, including carriage of pipes & fittings from site stacks to the place of laying etc. as

per direction of Engineer-in-charge.

Providing & Laying ( to level or slopes ) and jointing reinforce concrete non pressure pipes I.S. 100.00 Rmt. 671.32 Rs. Six Hundred Seventy One

class NP 2 of the following internal diameter with collars & butt ends prepaid for collar joints & Paise Thirty Two Only

including testin of joints. 300 mm dia pipe

Providing and fixing Pre-cast Rubber Dye/ Steel Dye inter locking concrete Block 60mm thick 450.00 Sqm. 700.54 Rs. Seven Hundred & Paise

grade of concrete M300 pnumatic compressed/vibrated mechanically and as per approved Fifty Four Only

design Conforming to IS 15658:2006 including 35mm sand layer for levelling and filling the

joint with sand in proper line and level as per guidelines of IRC: SP 63-2018 etc. complete.

Providing , Fabricating and fixing M.S. GRILL/GATE of approved pattern fabricated from 1030.00 Kgs 75.20 Rs. Seventy Five & Paise

M.S. flat,square bars, round bars,c-channel, box pipe as per detail Drawings. Rate is including Twenty Only

welding with grinding. Rate is also including two coats of Oil paint and one coat of yellow

19 Zinc cromet primer coat of approved brand only oil paint shall be used as per approved

material list of GSPHCL , steel must be of ISI mark only.

Providing and Fixing 1.20Meter high fencing with 2.0meter long M.S.Angle posts 170.00 Rmt 388.05 Rs. Three Hundred Eighty

40mmx40mmx6mm and oil painting 3 coats fixed at 2.5meter c/c.with five horizontal lines Eight & Paise Five Only

and two diagonals of galvanised steel barbed wire weighting 9.38 kg.per 100 meter,strained

20 and fixed to posts with G.I, staples including fixing the position ground with 0.5MX

0.5MX0.5M.block in C:C 1:5:10 etc complete.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

Finishing wall with Weather proof exterior emulsion paint on wall surface (two coats) over 230.00 Sqm. 155.21 Rs. One Hundred Fifty Five &

and above applying One Coat Of Primer to give an required shape even shade after Paise Twenty One Only

thoroughly brushing the surface to remove all dirt, and remains of loose powdered

21 materials.etc complete.Primer, Exterior emulsion paint shall be used as per approved material

list by GSPHCL ( For any height ).

Constructing brick masonry chamber for under ground C.I. inspection chamber and bends 21.00 No. 3793.18 Rs. Three Thousand Seven

with brick having crushing strength not less than 35 kg./cm2 in C.M. 1.5 precast R.C.C. cover Hundred Ninety Three & Paise

1:1.5:3 of Size 455 x 610 mm internal dimenslons. R.C.C. top slab with C.C. 1:1.5:3 mix (1 Eighteen Only

Cement : 1.5 coarse sand :3 graded stone aggregate 20mm size) foundation concrete 1:5:10

inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat

22 cment walls & bed connect etc. complete rate inclusive of outside plaster of 15mm thick in cm

1:3 form top of chamber and all side up to 15 cm deep below ground level. rate also inclusive

of providing and fixing precast cover of size 0.7 m x 0.5 x .07 m with 2 no of m.s. flat handle in

cement concrete 1:1.5:3.

Drilling of 200/300mm dia pilot bore hole in all strata by suing mudflush direct rotary ring by 60.00 Rmt 414.00 Rs. Four Hundred Fourteen

using Bentonite powder. Only

Reaming of 250/300 mm dia. pilot bore hole 60.00 Rmt 443.00 Rs. Four Hundred Forty Three

24 including assembling, lowering housing casing Only

,strainer pipes, gravel packing, clay packing etc. (450mm Rmt)

1.00 Job 18000.00 Rs. Eighteen Thousand Only

25 Conducation electologing test of 300mm dia.Bore hole incl.carting & idle-hour

Lowering and removing of 100mm dia dropline and 32mm dia air line for development of 1.00 Job 22205.00 Rs. Twenty Two Thousand

each water bearing zone come across upto full depth of tube well of size200 / 250 / Two Hundred Five Only

300mmdia. for tubewell having depth186meter and above through suitable air compressor.

The job is for complete period of development of tubewell. (Without charges for air

compressor)

Development of above mentioned bore by air compressor 900 cfm/200psi capacity upto 6 hrs 6.00 Hrs. 8415.00 Rs. Eight Thousand Four

27 minimum until sand free discharge of the above which ever is latter Hundred Fifteen Only

Supply of Gravel having size 4 mm to 6mm size 4.00 Cum 2029.00 Rs. Two Thousand Twenty

Bore plug having 100 mm height made from M.S.Plate with 3 holes at equal distance on 1.00 Nos. 774.82 Rs. Seven Hundred Seventy

29 circumference for nut-bolts lock nuts of std. make complete from 5 thick m.s. plate (for top Four & Paise Eighty Two Only

also) suitable for 200mm dia pipe.

Geophysical Survey for pin point for bore well including survey done by GWSSB department 1.00 Job 3571.00 Rs. Three Thousand Five

with ralay repail of pin point location including fees to GWSSB department & Transportation Hundred Seventy One Only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

Providing and supplying, specials D. I. K-7 grade pipes for following nominal bore 180.00 Rmt. 1477.00 Rs. One Thousand Four

diameter with internal cement mortar lining including all taxes, insurance, Hundred Seventy Seven Only

transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to departmental stores, stacking etc. complete. (IS 8329-2000). [150mm Dia DI K-

Lowering, laying and jointing C. I. S & S Spun pipes suitable for Tyton joints / Mortarlined 180.00 Rmt. 76.00 Rs. Seventy Six Only

D. I. K-7 Pipes of various classes with CI / MS specials of following diameters in proper

32 position, grade and alignment as directed by Engineer-in-charge including hydraulic

testing etc. comp.[150mm Dia]

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or

any other special as per BS-EN- 545/1995 Class- A series K12 suitable for use with DI pipes

manufactured as per IS: 8329/1994 delivery of specials is to be made to GWSSB store or site of

wroks any where in Gujarat including all taxes, loading, unloading, carting, stacking,

33 insurance, inspcetion charges, octroi etc. complete. D.I. / CI Specials upto 300 mm

Diaincluding all necessary tools, tackle, machine & skill mistry.

A) Socket & Spigot Type

80 to 300 mm Dia 660.00 Kg 148.00 Rs. One Hundred Forty Eight

B) Flanged Ended

80 to 300 mm Dia 660.00 Kg 155.00 Rs. One Hundred Fifty Five

Providing, Supplying, Lowering, laying and jointing in position following C. I. / D/F 2.00 No 3831.00 Rs. Three Thousand Eight

Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of all Hundred Thirty One Only

34 labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc.

complete.(Reflux Valve 65 MM Dia)

4.00 No 2302.33 Rs. Two Thousand Three

35 Providing and fixing gun metal check or non return full way wheel valve (A) 50mm diameter Hundred Two & Paise Thirty

Three Only

8.00 No. 656.86 Rs. Six Hundred Fifty Six &

36 Providing and fixing gun metal check or non return full way wheel valve (B) 40mm diameter

Paise Eighty Six Only

10.00 No. 416.47 Rs. Four Hundred Sixteen &

37 Providing and fixing gun metal check or non return full way wheel valve (C) 25mm diameter

Paise Forty Seven Only

Providing and supplying ISI mark CI D/F Sluice Valves , Butterfly Valves & Reflux Valves of

following class and diameter including all taxes, insurance, transportation,freight charges,

octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking

etc. complete. A1) PN-1 With hand wheel /cap operated (PD type short body)-50mm dia.

1.00 No 5848.00 Rs. Five Thousand Eight

(A) PN-1 With hand wheel/cap operated(PD type short body)150mm Dia.

Hundred Forty Eight Only

1.00 No 8027.00 Rs. Eight Thousand Twenty

(B) Reflax Valve PN 1 IS 5312 WITH ISIS mark 3 (150mm dia.)

Seven Only

TOTAL CIVIL WORK Rs.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

Electrical item

8.00 Point 605.00 RS: Six Hundred Five

Providing & erecting Point wiring with 1.1 KV grade ISI marked 2 X 1.5 sq. mm copper PVC

insulted FRLSH wire with 1.5 sq. mm (green) copper PVC insulated FRLSH wire for earth

continuity in FIA approved ISI mark medium class white colour 20/25 mm dia. embossed

rigid PVC pipe with PVC fitting fixed with adhesive solution erected on/in Brick Wall /

slab along with continuous G.I. fish wire to draw wires and laid in approved manner zari

for PVC pipe and boxes shall be filled with cement mortar and finishing the surface to

match the wall / ceiling complete with approved make 5/6 Amp. ISI make modular type

switch and accessories mounted in 20 G. G.I. company fabricated metallic box covered with

appropriate front plate modules erected flushed with wall / ceiling with necessary modular

lamp holder / modular ceiling rose / HD Connector as directed..(Deep Junction box 75mm

depth if required)(Make & Model approved by EIC and matching colour with switch and

accessories) for concealed wiring. Light point. Cat.-III.

Necessary sheet / tape / polythene / sand must be erected or filled in all box to prevent

mortar going into the box. Length of point wiring must not increase than 10 mtr. For that

necessary switch boards and their locations must be finalised before execution by agency

otherwise payment will not be done for extra long point. (For future extention, if required,

agency has to erect one higher size metal box and modular plate as per instruction of EIC.

Cost of blank plate shall be paid as per tender item) [This item include cleaning

(inside/outside) of all G.I. switch boards, electric point box, fan box, MCBDB & box cutting

plaster finishing for modular plate without any gap] (Conductor resistance should be as per

39b For Fan Point (with 6 A. Modular type switch and two module hum free EME Five step type

RS: Eight Hundred Forty

Electronic fan regulator both having ISI mark) Cat.-III 2.00 Point 842.00

39c For separate Point (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) Cat.-III RS: Six Hundred Thirty

2.00 Point 636.00

39d For Looped on switch board (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) RS: Three Hundred Six

4.00 Point 306.00

Cat.-III. only

40a Providing and erecting 1.5 mm thick FIA approved and ISI mark (embossed) RIGID white

Colour PVC PIPES of following size complete erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution concealed in wall / slab along with contineous

fish wire to draw mains, laid in approved manner with plastering by cement mortar &

100.00 Mtr. 24.00 RS: Twenty Four only

finishing the surface to match the wall / ceiling. 20 mm dia.

40b For 25 mm dia.

50.00 Mtr. 33.00 RS: Thirty Three only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

41a Providing and laying Mains with FRLSH PVC Insulated wire ISI marked 1.1 KV grade

with FIA approved ISI mark medium class 20/25/32 mm dia. embossed rigid PVC pipe

with PVC fitting fixed with adhesive solution to be erected on/in brick wall / slab along

with continuous G. I. fish wire to draw mains laid in approved manner with plastering by

cement mortar & finishing the surface to match the wall / ceiling complete with FRLSH

PVC insulated wire for earth continuity. (Approved ISI make only) [a] 2 x 1.5 sq.mm.

FRLSH copper multi stranded conductor mains with 1.5 sq.mm. FRLS copper multi 40.00 Mtr. 81.00 RS: Eighty One only

stranded conductor for earthing as per standard colour code. [conductor resistance should

be as per IS:8130/1984]

41b For 2 x 6.0 sq.mm. FRLSH copper multi stranded conductor mains with 2.5 sq.mm. FRLSH

copper multi stranded conductor for earthing as per standard colour code. (with 25 mm dia.

RS: One Hundred Ninty

PVC pipe) [Wire must be having box packing] (Conductor resistance should be as per 25.00 Mtr. 192.00

42 Providing & fixing 20mm. dia. PVC insulated G.I. corrugated Flexible pipe with necessary 30.00 Mtr.

socket, PVC bushes saddle, Check-nuts etc. complete of following sizes. RS: Thirty One only

43 Providing and fixing Plug Point wiring with 1.1 KV grade ISI marked approved make 2 x 2.00 Point

2.5 sq.mm copper PVC insulated FRLSH wire with 1.5 sq.mm (green) copper PVC insulated

FRLSH wire for earth continuity in FIA approved ISI mark white colour medium class

20/25 mm dia. embossed rigid PVC pipe with PVC fitting fixed with adhesive solution

erected on brick wall/slab along with continuous G. I. fish wire to draw wires and laid in

approved manner complete with approved make 16 Amp Modular type Swich and

accessories mounted in 20 G. GI company fabricated metallic/PVC/Acrylic box covered

with appropriate front plate modules erected flushed with wall. (a) 16 Amp. Indicator RS: Nine Hundred Thirty

switch & 1 No. 6/16 A universal socket white colour suitable for 3 pin top duly both having only

ISI mark. (Necessary sheet / tape / polythene / sand must be erected or filled in all box To

Prevent Mortor Going In To The Box) Cat.-III

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

44 Providing & Erecting 2.0 mtr long Earthing system by making minimum bore of 225 mm

dia in soft soil. Suitable for doing pipe-in-pipe technology earthing.Earthing electric rod

must be made from Corrosion free Hot dip galvanizing pipes having following

specification.

(A) Earthing Electrode: outerpipe:- 88 mm minimum O.D., ISI 'B ' Class ISI mark of

Reputed Brand, Inner pipe:- 42 mm minimum O.D., Pipe B Class ISI mark reputed Brand

Terminal Size: 70mm X 100mm length, Terminal Should be made from inner pipe for that

pipe must be pressed and gave rectangular shape so its work as a terminal.The hot deep

galvanising must be done after above process.Galvanised thickness must be minimum

micron any where. SS Nut bolt:- 2 no.with washer suitable for 14mm dia. hole must be

provided at terminal. total minimum Weight(approx.) of earth electrodewith inside RS: Seven Thousand

conductive material minimum should be 26 kg. 4.00 Each 7025.00

Twenty Five only

(B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm/meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%

(C) Back fill Compound:- Earthing compound should be capable to retain moisture for long

time Back Filling Compound weight is 25 Kg.

(D) Chamber and cover:- Earthing chamber should be size of 400 mm X 400 mm X 400 mm

Necessary test report must be submitted.

1. Short circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL accredited lab.

3. Hot dip galvanised / zinc coating micro test from reputed laboratory.

4. General test report from OEM regarding specification of earthing.

[Make and model approved by EIC Strictly subject to item specification only] [OEM has to

submit all detail & sample for approved before supplying]

[Water must be poured in bore before starting earthing. Earthing value must be measured

between neutral & Earthing upto 02 volt. Agency has to maintain earthing & its value for

one year. Earthing must be done in the presence of A.E. (GSPHCL)]

45 For Above Earthing Additional charges for boring in hard rock soil (By Breaker) & filling

soft soil in earth pit. (Certificate for soil have to given by DEE/AE along with Photographs). RS: Three Hundred

Twenty Five only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

46 Supplying & erecting Sintex or approved make SMC press moulded composite FRP. loop-

in, loop-out approx. 2mm thick box complete with bakelite connector strip 4way & hinged

doors having locking arrangements with mounting clamp with nuts, bolts & washers

RS: Five Hundred Ten

suitable for erection on pole with cable clamps& earth bolt of following size of box. (b) 250 2.00 Each 510.00

mm x 200 mm x 100 mm [deep]

47 Supplying and Erecting LED indoor fitting of approximately 4feet long with LED of

wattage 0.2W to 0.5W assemble on single MCPCB with housing use as a heat sink shall be

made from Aluminum extrusion having enough strength (sample must be approved by

EIC)with polycarbonate diffuser with following specification:

(A) Company mark/name on the fitting.(B) Rated input voltage and frequency: 220V to

VAC ; 50Hz.(C) Rated input wattage: max. 24w(D) Rated input current : 0.2 Amp(E) Power

Factor : Min. 0.90(F) ATHD :Max. 15%(G) Rated Luminous flux: Min. 2420 lm(H) CCT:

6500K(I) CRI: Min. 80Ra(J) Driver Efficiency: Min. 80%(K) LED life span: Min. 50000 Hrs @

L70(L) Over Voltage protection: Withstand up to 440V/AC for 4 Hrs.(M) Surge protection :

Min. 2KV(N) IP rating: IP 20(O) IK rating : IK

(P) Short circuit , Open circuit & Reverse Polarity Protection must be provided(Q) Fixing

clamp design & strength should be sufficient to hold the fitting erected on wall or RS: Three Hundred

ceiling.(R) 3 core copper wire of appropriate size with earthing connector Seventy only

(Note:-The manufacturer/ authorized Channel partner of the manufacturer has to submit

4 yrs free replacement Guarantee for complete Fixture) [Approval will be given strictly

subject to item specification]

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

48 Providing, erecting, testing Ceiling Fan confirming to IS: 374/1979 AMDT No. 1 to 6 Class-I,

50 Hz. Specification of Ceiling Fan must be as per below. (1) Sweep: 1200 mm, (2)

Operating Voltage: 180 to 230 V, (3) Power Factor: > 0.9, (4) Power Consumption: maximum

53W, (5) RPM: minimum 330, (6) Service value:min 4.3 m3/min. (7) Class of insulation: 'B',

(8) No. of heavy duty premium quality Ball bearing: Two, (9) Total Body: Top & Bottom

should be alluminium, (10) Blade: Aluminium approx 1.1 mm thick, (11) Colour: White

high grade powder coating, (12) Canopy: Two Nos. Heavy duty, (13) Condenser: 1.5 MFD

Aluminium body premium quality, Branded make, (14) Down road: up to 1.0 mtr as per site

requirment, (15) Required fixing accessories, (16) 3 core 0.50 sq.mm ISI wire as per site

requirment, (17) No vibration and noise due to mechanical parts. (Agency has to erect safey RS: One Thousand Nine

wire with ceiling fan and checked with EIC) (OEM has to approved model as per tender 2.00 Each 1929.00 Hundred Twenty Nine

specification and tested at ERDA) (Necessary test reports should be submitted strictly at only

the time of approval. Sample approved by EIC subject to above specification only)

49 Supplying and erecting 8 W LED lamps with following wattage capacity of 220 to

voltage, minimum 15000 burning hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED Lamps RS: One Hundred Eleven

integral type, with PC diffuser suitable LAMP holder only

50 Providing and erecting PVC body surface mounting LED Bulk head type 9 watt Lighting

Fitting with electronic driver having THD < 15%, CRI>80, P.F.0.95 And lumen output from

luminaire 720 lm, input voltage range 160-270 V AC, 50 Hz cool white (3000 to 6500 k),

RS: Seven Hundred

inbuilt driver having efficiency >=80lm/w, -20 deg C to + 60 deg C working temperature, 2.00 Each 780.00

Eighty only

AL frame with Beam Angle 120 deg.

51 Supplying & Erecting Fan Hook Of 10 mm M.S Round bar bounded to the RCC bars up to

50 mm Length each side & piereced through 18 Gauge G.I Box having 125 mm dia depth of

RS: One Hundred Twenty

75 mm complete erected concealed in ceiling with necessary round modular plate 2.00 Each 125.00

Five only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

52 Desiging,fabricating,testing electrical panel (switch board) at manufacuturer's workshop 1.50 Sq. Mtr.

and Providing & erecting at site. Panel should be weather proof, dust & vermin proof, floor

mounted front operated cubical panel board having IP-54 made from 2 mm. thick CRCA

M.S. sheet for outer body,gland plate & doors, 1.6 mm. thick CRCA M.S. sheet for internal

partitions with necessary supporting angles, flats including skirting, bending, drilling,

welding, riveting with internal partitions & cable alley,rubber gromets, rib, control wires,

backelite control fuses as per requirements,sufficient nos. of hinges for doors, door locking

arrangement, rubber gasket complete with Required Nos. heavy Duty Connector with

Cadmium plated nut and bolt for Anti rusting and Al.busbar for earth, nuts/bolts,washer

etc as per instruction of engineer-In-Charge. Cost of supplied item like switchgears, LED RS: Twenty One Thousand

indicator ,CTs , busbars and PVC FRLS copper wire with suitable size for power

Five Hundred only

interconnection,measuring instruments, foundation flange-bolts-base plates, cost of C

channel/angle iron stand (1ft to 2ft height as per cable size)shall be excluded of panel

fabrication.Specification of suppiled items is attached seperatly.

The panel shall be supplied with Seven Tank chemical process. which shall be carried out before

applying painting, painted with powder coating. (The rates excludes the cost of switchgears,

busbars, interconnecting mains & Copper / Aluminium strip, fuse, meters etc. The dimension shall

be measured excluding base beams.switchgear of approved brand and specification shall be used

and erected at CPRI approved panel manufacturers only. Busbar compartment must be separate for

easy termination of tails/cables and to avoid least distance of punching holes in busbar. Panel

depth shall be 350 mm. Panel manufacturer have to give 4 years service support if in case of

breakdown or fault. Panel manufacturer have to submit electrical meter calibration report. Agency

should design the panel in such a way that there should not be any excess in panel area (sq.mtr) &

length of bus-bar (mtr), if any excess is need to be done agnecy has to draw attention to GSPHCL at

the time of approval of G.A. drawing.

Loading and unloading of above item shall be done by hydra and skill work force under

supervision of electrical engineer and guidelines given by manufacturer to avoid damage to the

Size of door and Ele. room / Pump room shall be measure and provide to panel manufacturer to

prepare GA drawing considering the size of electrical room/pump room door and also inside size of

it. Agnecy has to co-ordinate with civil agency for giving proper dimenssion of electrical

room/pump room to accomodeted panel easily.[Including Necessary numbering / marking on

PANEL done with red colour radium sticker as per site requirement and instructions given by EIC

on site. Font / number size given by EIC on site as per requirement] (See attached details

specification of panel & manufacture also while quoting rate. [Manufacturer must be of Gujarat

state so three stage inspection can be done if required and service support]

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

53 Providing and erecting Approved make Three pole moulded case circuit breaker having 1.00 Each

breaking capacity ICU of 35 K.A. at 415 V having normal current rating of 125 A. with

variable/Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all

Rs. Seven Thousand One

internal connections, spreader tinned copper & complete erected in existing 16 G.M.S.

hundred Sixty-One Only

housing. ICS=100% of ICU only. Cat.-III

54 Providing and erecting Approved make Four pole moulded case circuit breaker having 1.00 Each

breaking capacity ICU of 35 K.A. at 415 V having normal current rating of 125 A. with

variable/Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all RS: Eight Thousand Seven

internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. Hundred Seventy Four

housing. ICS=100% of ICU only. Cat.-III only

55 Providing and erecting Approved make Four pole moulded case circuit breaker having 4.00 Each

breaking capacity ICU of 25 K.A. at 415 V, having normal current rating up to 25 A to 100 A.

with variable/Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. RS: Six Thousand Seven

with all internal connections, spreader tinned copper & complete erected in existing 16 Hundred Twenty Three

G.M.S. housing. ICS=100% of ICU only Cat III only

56 Supplying & Erecting Approved Make Neutral link for (i) 32 / 63 / 125 Amps as per site 2.00 Each 136.00 RS: One Hundred Thirty

requirement and instruction of EIC. Six only

57 Supplying & Erecting Approved Make Extended operating rotary handle with pad lock 5.00 Each

with three position Trip, Off, On suitable for 25 Amp. to 250 Amp. panel RS: Nine Hundred Fifty

mounting.(Company Must be same company of switchgear) cat-III Two only

58 Supplying and erecting tripple pole & neutral 440V / 500 V Panel mounting Copper 2.00 Rn.Mtr

Busbars with four equal Nos. of electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly wraped with colour insulating tape

for phase sequence of following current carrying capacity, erected with necessary bus bar RS: Three Thousand One

supports / insulators, main cable socket to each bar, erected in existing cubical panel with Hundred Seventy One

necessary connections.For electrolyte copper busbars suitable for 200 Amp. capacity only

59 Supplying and erecting Approved make Earth fault Relay suitable to mount with inter 1.00 Each

connection to moulded case circuit breaker having CT ratio & MCCB rating as following

along with shunt trip 220 V AC with all internal connections & complete erected in existing RS: Five Thousand Four

M.S.housing.(2) 125 A - 200 A, CT Ratio 1/200 [make and model approved by EIC strictly as Hundred Twenty Seven

per tender specification] only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

60 Providing and erecting multifunctional meter suitable for application of Power monitoring 1.00 Each

and showing measurement of following Voltage, Frequency, Apparent energy, Apparent

power, Active and reactive energy, Active and reactive power, Average voltage Vavg, Peak

demand power PM, QM, SM, Demand power P, Q, S, Apparent power S, S1, S2, S3,

Unbalance current, Power factor and displacement PF (signed, four quadrant), Calculated

neutral current, Active, reactive, apparent energy (signed, four quadrant), Active power P,

P1, P2, P3, Voltage U21, U32, U13, V1, V2, V3, Phase currents, Average current Iag, Peak

demand currents, Reactive power Q, Q1, Q2, Q3, Demand current I1, I2, I3, [Us] rated RS: Thirteen Thousand

supply voltage 40...300 V AC 45...65 Hz, 40...300 V DC, Network frequency 50 Hz, Type of Nine Hundred Eighty Four

network 3P, Display type 7 segments LED, Display colour Red, Messages display capacity 3 only

fields of 4 characters, Display digits 12 digit(s) - 14.2 mm in height

61 Providing and Erecting of Miniature circuit breaker single pole 6 Amp. to 25 Amp. suitable 3.00 Each

to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in RS: One Hundred Twenty

existing box. confirming to IS 8828/1996 with ISI Mark. Cat-III. Two only

62 Providing & erecting 240 V MCB Double pole switch for Motor & Inductive load (C curve) 4.00 Each

having 10 KA breaking capacity & confirms to IS:8828 in Existing M.S. box having RS: Three Hundred Sixty

following capacity. For 40 Amp. Cat III only

63 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 2.00 Each

10KA breaking capacity & confirms to IS :8828 in existing box having following capacity [c] RS: Eight Hundred Three

63 Amp. Cat III only

64 Supply, Installation, Testing & Commissioning of Three Phase, 440 V Surge Suppressor 1.00 Each

protection Device (SPD) & 40 Amp TPN MCB (or As per SPD OEM guide line for the

protection of SPD which is erected such a way that it can be operated easily) SPD must be

capable to protect all electrical and electronics equipments if SPD blast or fuse then the

panel builder must have replace it soon during defect liability period.The Detail RS: Six Thousand Three

Specification of SPD are As per Attached sheet with Annexture -A(E). (Hakel,ikra,OBBO

Hundred Ninteen only

make) (With Three year Gaurantee/warranty)

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

65 Providing, erecting, Fabricating the M.S. structure as per requirement of site as per 60.00 Kg.

structure design Including proper size approved by EIC of M.S. angles, flats, bars, square

pipe, channels, sections (Tata, Jindal, Asian, JSI Make) complete with cutting, welding,

grinding and finishing duly painted with Asian/Nerolac make premium quality oil paint

and true care red oxide metal primer,asian paint make with erection on site as per direction

of engineer in charge with necessary grouting cementing, plastering and finishing RS: Seventy Seven

complete. All hole opening of square pipe end must be closed with M.S plate welding. only

Payment will be done on KG as per Actual weight.

66 Supplying & erecting 12 mm thick backelite sheet of approved make and grade on existing 1.00 Sq. Mtr.

min. 25 x 25 x 3 mm red oxide painted angle iron frame suitable for fixing ICDP / MCB

SWITCH and energy meter (contractor shall make approved drawing of Bakelite sheet To

RS: Two Thousand Two

arrange required No. of Energy meter & ICDP / MCB switch -busbar etc. as per Actual

Hundred Eighty Nine only

space available in electrical room at site)

67 Providing and erecting metalic danger notice board for MEDIUM VOLTAGE installation to 2.00 No.

RS: Sixty Nine only

be erected as per I.S.

68 Providing ad erecting approved make single phase Double Door metal clad D.B. as per 1.00 Each

relevant indian standards ammended upto date.

Supplying and fixing following way single phase MCB distrubution board of company

fabricated IK 09 certificate with sheet box with powder coated inside and outside after

apply seven tank chemical process of MS sheet cover complete with suitable integral single

piece construction tinned copper busbar and link with all necessary interconnection and

with necessary size MS frame for mounting MCBDB. Manufacturer must be provided (1)

IP 30 and as per IS:8623-1 & 3, IEC 61439-1 & 3 having D type PU gasket. (2) Seven tank

Powder coating Certificate (3) Tinned Copper/Brass make neutral & Earthing link with

isolation & Protecting Cover for 240 Volts on surface / recess complete with loose wire box, RS: Four Thousand Six

terminal connectors for all incoming and outgoing circuits, with suitable size FRLS PVC

Hundred Fifty One only

insulated copper conductor up to terminal blocks and internal connection, tinned coppper

bus bar, 1 no. tinned copper neutral link, tinned copper earth bar, din bar, detachable gland

plate, interconnections, powder painted including earthing etc.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

Single phase incoming and horizontal single phase outgoing. For 8 Way MCBDB:

Including 40 Amp. 30 mA double pole ELCB (ELCB confirming to IS:12640/1988 having

sensitivity of 30 mA and breaking capacity of 10 KA), MCB 40 Amp. double pole switch (C

curve confirms to IS:8828 having breaking capacity of 10 KA) and S.P. MCB of rating 6 to

Amp. with NL suitable to operate on 240 Volt A.C. power. (6 Amp:- 2 Nos., 16 Amp:- 2Nos.

& 25 Amp: 2 Nos.)

(The DBs should be used of same company of MCB / ELCB to be used) (MCBDB must be

erected in line & level with spirit level and finish the external edge with box cutting

Necessary numbering / marking on box done with red colour radium sticker as per site

requirement and instructions given by EIC on site. Font / number size given by EIC on site

as per requirement]

69 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 1.00 Each

10KA breaking capacity & confirms to IS:8828 with same company metal box with earthing

RS: One Thousand Two

terminal having following capacity with necessary Numbering / marking with oil Paint by

Hundred Eighty Nine only

painter. [c] 63 Amp. Cat.-III

70 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 1.00 Each

10KA breaking capacity & confirms to IS :8828 with same company metal box with earthing

terminal having following capacity with necessary numbering/marking with oil paint by RS: One Thousand One

painter. For 40 Amp. Cat.-III Hundred Eighty One only

71a Providing and laying Mains with ISI marked, 1.1 KV grade electrolyte multi stranded, 60.00 Each

annealed copper conductor with heat resistant PVC insulated conforms to IS:694, IEC -

erected in existing pipe of following size (Specifically for control panel, relays, power

RS: One Hundred

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and

Seventy Six only

bolts if required. [g] One wire 16.00 sq. mm [For Earthing]

71b One wire 10.00 sq. mm 60.00 Mtr. 114.00 RS: One Hundred

Fourteen only

71c One Wire 25 sq.mm wire 15.00 Mtr. 293.00 RS: Two Hundred Ninty

Three only

72 Supplying and erecting approved make single phase servo controlled voltage stabilizer 1.00 Each

suitable for input voltage range 180/250 V And output voltage range 225/235V. A.C. RS: Six Thousand Three

complete erected. (a) 1.0 KVA Single Phase. Hundred Ninty One only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

73 Providing and erecting XLPE (IS:7098) (I)-88 ISI armoured cable multistrand Aluminium 50.00 Mtr.

conductor for 1.1 KV. to be laid 90 cms. Under ground or to be laid on wall with suitable

G.I. heavy guage 1.0 mm thick cable clamp or in existing DWC pipe underground or road RS: Three Hundred

crossing or floor of following size of cables.(C) 3 1/2 core 50 Sq. mm (25 Sq. mm 1/2 core) Thirty Eight only

74a Providing & erecting XLPE (IS : 7098) (I)-88 ISI marked armoured Copper cable for 1100 30.00 Mtr.

volt to be laid 90 cms. Under ground or to be laid 90 cms. Under ground or to be laid on

wall with suitable G.I. heavy guage 1.6 mm thick cable clamp or in existing DWC pipe RS: Three Hundred

underground or road crossing or floor of following size of cables.For 4 core x 2.50 sq.mm. Thirty Six only

74b For 4 core x 4 sq.mm. 30.00 Mtr. 451.00 RS: Four Hundred Fifty

74c For 4 core x 10 sq.mm 20.00 Mtr. 838.00 RS: Eight Hundred Thirty

Eight only

75a Providing & laying HDPE Double walled corrugated pipes (DWC) (conforming to IS: 16205 80.00 Mtr.

(part 24) 2018)) with minimum load required of 450N capacity with anti rodent and ultra

violet material properties with necessary connecting accessories of same material at

required depth to be laid 90 cms. under ground for laying of cable below ground / road

surface for enclosing cable and back filling the same to make ground as per original. (A) RS: One Hundred

For Outer dia. 50 mm and Inner dia. 38 mm.) (Test Certificate to be Submitted) Seventeen only

75b (C) For Outer dia. 90 mm (Test Certificate to be Submitted) 30.00 Mtr. 150.00 RS: One Hundred Fifty

76 Providing & erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked 20.00 Mtr.

copper wires of following size to be erected as directed. 3 core x 1.5 sq.mm. PVC insulated

RS: Fifty Eight only

round copper wire ISI mark.

77 Supplying & Erecting following size of Light duty “A” Class G.I. Pipe & erecting as 10.00 Mtr.

RS: One Hundred

directed by Engineer-in-charge. For 25 mm dia.

Seventy One only

78a Providing & fixing double compressed heavy duty flange type brass cable gland with 8.00 Each

rubber ring for P V C insulated armoured cable complete with outgoing tails, insulating

tape etc. For following size cables. For 2 to 4 core x 4.0/ 6.0 Sq. mm (Sigma, MCI, Comet RS: Forty Three only

Make Only)

78b For 2 to 4 core x 10.0 Sq. mm (Sigma, MCI, Comet, Make Only) 4.00 Each

RS: Forty Seven only

78c For 3*1/2core*50 Sq. mm (Sigma, MCI, Comet Make Only) 4.00 Each 75.00 RS: Seventy Five

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

79 Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole

should be made as per IS. and shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with integral Junction box with Hot

Deep Galvanised door having 2 nos. 180° operated hinges & 2 nos. Ln key locking with

silicon rubber gasket. Consist of terminal plate of min 6mm Hylam sheet, standard profile

35 mm X 7.5 mm Din-Rail & MCB, Brass stud type terminal and arrangement for cable RS: Twelve Thousand Five

termination to be erected on RCC foundation as per details given by manufacturer and EIC 2.00 Each 12551.00

Hundred Fifty One only

considering site requirement.

For 7 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm thickness with 225 mm X 225 mm

X 16 mm base plate, 4-M20 Bolts and 600 mm long hot deep galvanized J-Bolt, nuts,

washers with. Approx Pole weight 67 kg.(Make:- Bajaj, Valmont, Transrail, Ambica Only)

(Test certificate to be submitted)

80 Providing & erecting bracket consisting of ISI mark "B" class G.I. Pipe 4.2 cm outside 2.00 Each

diameter complete with suitable G.I. Sleeve tubing of 2 mm. thick and required size and

length suitable for 76.5 / 80 mm. required size of pole top or pipe in pipe surface for terrace

as per instruction of EIC or wall bracket as per instruction of EIC having nuts and bolts for

fixing the brackets and having spread of Upto 0.70 mtr. length with suitable rise as per site

condition and suitable welded stiffner reducer and nipple with check nut complete painted

with one coat of yellow zinc and two coats of alluminium paint for Single arm bracket RS: Four Hundred Eighty

suitable for pole or terrace as per design given by EIC (a) For single arm bracket. (Jindal /

Seven only

Asian / Tata / Surya Prakash make Only) (Fabricators:- Bajaj, valmont, Transrail, Ambica

Only) (Test certificate to be submitted)

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

81 SITC of Outdoor aesthetically designed LED Street Light Luminaire with total 2.00 Each

consumption of max. 55 Watts with single piece heavy duty & sufficient size of die cast

aluminium housing to accommodate driver, both SPD and necessary wiring and terminal

easily inside the housing. High power LEDs wattage of 5 Watt (Driving current of LED

should be max. 80% of Rated current) shall be mounted on high quality metal core PCB

with extremely precison designed heat sink complete with IP66 protection. LED lense are

covered with thoughened glass / premium cluster Lens for better light distribution. The

fixture should be suitable for pole/bracket mounting. The fixture should be complied with

both LM79 and LM 80 certified. LED module should be tested L70 at 50,000 hrs ( All Test

Certificate must be submitted with RA bill). LED fitting provided with high quality potted

driver with Metal housing and protection against high and low Voltage cut Off, Protection

against 440V. Driver should have protection like over current, over voltage, short circuit

and operational in the temperature range of 0 deg to 50 deg and humidity range of 10% to RS: Four Thousand Four

90% RH. THD of driver should be less than 10% and P.F > 0.95. The Fixture should meet Hundred Six only

the technical criterias like Operating Voltage range 180 to 270 V, total lumens of fitting not

less than 7500, CCT> 4K/6K as per site requirement & decided by EIC, CRI > 65, beam

angle 120 deg, surge immunity level at least 4 KV integral and 10 KV non integral. (Note:-

The manufacturer / authorized Channel partner of the manufacturer has to submit 5 yrs

free replacement Guarantee for complete Fixture)

82 SITC of Outdoor aesthetically designed LED Flood Light Luminaire with total 4.00 Each

consumption of Max.105 watts with single piece heavy duty & sufficient size of die cast

aluminium housing to accommodate driver, both SPD and necessary wiring and terminal

easily inside the housing. High power LEDs of 5 Watt (Driving current of LED should be

max. 80% of Rated current ) shall be mounted on high quality metal core based PCB with

extremely precised designed heat sink, complete with IP66 protection. LED lense are

covered with toughened glass / premium cluster Lens for better light distribution. The

fixture should be suitable for pole/bracket mounting. The fixture should be complied both

LM79 and LM 80 certified. LED module should be tested L70 at 50,000 hrs( All Test

Certificate must be submitted with RA bill). LED fitting provided with high quality potted RS: Six Thousand Three

driver with Metal housing and protection against high and low Voltage cut Off, Protection

Hundred Sixteen only

against 440V. Driver should have protection like over current, over voltage, short circuit

and operational in the temperature range of 0 deg to 50 deg and humidity range of 10% to

90% RH. THD of driver should be less than 10% and P.F > 0.95.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

83a Providing & fixing Solderless crimping type Copper lugs conforming to IS suitable for 50.00 Each

cable of following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. [a] 1.5/2.5 to 6 RS: Eight only

83b (B) 10 Sq.mm 16.00 Each 10.00 RS: Ten only

84a Providing & fixing Solderless crimping type Aluminium lugs conforming to IS suitable for 12.00 Each

cable of following size evenly crimped with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an approved manner. [d] 50 Sq.mm. RS: Twenty only

84b (C) 16/25 Sq.mm. 4.00 Each 15.00 RS: Fifteen only

85 Providing , erecting Universal Astro Intelligent streetlight control system Insu with

RS: Eighteen Thousand

weather Proof box for Indoor application 5 KVA (As Per Atteched Technical Specification) 1.00 Each 18406.00

Four Hundred Six only

86 Supplying and erecting Servo Controlled Voltage Stabilizer (SCVS) as per following 1.00 Each

requirement: (1) Input Voltage Range - Three Phase 340 To 480 Volt AC. (2) Out put

Volatge - Three Phase 415 Volt AC (Line - Line) with Voltage Regulation of +/- 1%. (3)

Frequency range - 47 Hz To 63 Hz. (4) Efficiency - More or equal to 98%. (5) Type of

Stabilizer - Suitable for Balance & Unbalance Load and Voltage including SPD (6)

Controlled Type - Digital Micro Controller Based Disply. (7) Rate Of Correction - Upto

Volt / Sec (Line - Line) (8) Servo Motor Drive - AC Syncronous Stepper Motor - As per KVA

Capacityy, Out put volatge and Voltage regulation requirement. (9) Nil Wave form

Distortion and Effect of Load POwer. (10) Responce Time - 10 milli second. (11) Protection

requirements - Input low Cut off protection / Input High Cut Off Protection / Output Low

Cut Off protection / IOutput High (12) Fault Annuciation Panel LED shows Input present, RS: Seventy Thousand

Input high Input low, Output Normal, Output High, Outpur low, Overload. (13) Output On Four Hundred Thirty Eight

time delay - 10 seconds (14) Ambient Tempeature capacity - 0 - 45 RH upto 90 %. (15) only

Enclosure Type - IP20 (16) Type of Cooling - Air,Output:Bypass switch with changeover

switch, & 4 year free replacement guarantee on Stamp paper.

Loading and unloading of above item shall be done by hydra and skill work force under

supervision of electrical engineer and guidelines given by manufacturer to avoid damage

to the item. Picture of it to be submitted in running bill / final bill.Size of door and Ele.

room / Pump room shall be checked by agency's engineer before giving order. If found any

problem in size discuss with GSPHCL engineer for rectification before giving order.

KVA (Air Cooled) (make - Fuji-Electric,Servomax,Krykard)

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

87 SITC of Vertical Air Termination Solid aluminium with Base - 10 mm dia. and 1000 mm 3.00 Nos.

long. Air Termination Base tested for conditioning, Ageing Test & Lightning impulse

current withstand test: 100 kA of 10/350 µs waveform in an accredited. Third party RS: Nine Thousand Three

laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol with MAST 34 mm dia. as per EIC Hundred Twenty Three

(OBBO, JEF, CAPE, DHEN) only

88 Supplying, installation, testing & commissioning of Die cast aluminium housing with red 1.00 Each

polycarbonate dome for better illumination & integral driver IP-65 protection LED

Aviation light luminaries including required driver/ control box, protections, above the

highest point of terrace level and making good the same. It should switch ON

automatically as required in night time & OFF in day time including FRLS copper control

wiring etc. complete in all respect as required & as approved by the Engineer Incharge. RS: Four Thousand Eight

(fixing height may please be considerd as per the site requirement) [make and model Hundred Twelve only

approved by EIC strictly as per tender specification]

89a Supplying and erecting approved make GRP/FRP Perforated type Cable Tray Material – 30.00 Rn.Mtr

Corrosion Resistant Polyester Flame Retardant U.V. Stabilized Resin System -

Manufactured from Pultruded Sections- Polyester Resin System, Glass Content : 55 – 60 % -

- Standard Length : 3000 mm- Support Span – 1500 mm, Deflection L/200 - Specification

NEMA FG1 1993- UV Resistant - Flame Retardant – IS 6746 - Appendix K/UL 94, Very Low

Flammability - Specification Followed NEMA FG1 1993 Oxygen Index – Minimum 30% as

per ASTM D 2863 - Flame Spread (Extent of Burning) – 20 mm as per Standard ASTM D

635 - Tensile Strength – 4000 – 8000 Kg/Cm2 as per Standard ASTM D 638 - Flexural

Strength – 2500 – 10000 Kg/Cm2 as per Standard ASTM D 790- Izod Impact Strength – 130 RS: Five Hundred Twenty

Kg/Cm2 as per Standard ASTM D 256- Compressive Strength – 2500 – 5000 Kg/Cm2 as per

Standard ASTM D 695- Barcol Hardness – 50 – 65. Width 300 mm, Side Member “C”

Section : 100 x 35 x 35mm with 4mm Thickness, Loading 60Kg./Mtr. With Concentrated

Load 70Kg. at center of the span

89b For Width 150 mm, Side Member “C” Section : 75 x 25 x 25mm with 4mm Thickness, 30.00 Rn.Mtr

RS: Two Hundred Thirty

Loading 30Kg./Mtr. With Concentrated Load 70Kg. at center of the span.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

90 Providing open well type horizontal submersible mono block pump set with cast iron body 2.00 Each

having following specification [b] For 3 phase open well horizontal mono block pump set

suitable for [c] For 3.00 HP Three phase open well horizontal mono block pump set suitable

for 85 LPM to 270 LPM @ 11 mtr to 33 mtr head suitable for 50/65 mm dia delivery pipe

with 10 mtr. necessary Size 3 Core Flat copper flexible cable. (Body: Cast iron / Winding :

Copper / stator : Copper / rotor : Copper / shaft : SS 304 material test certificate from

manufacture shall be submitted).

For 3 HP 3 phase open well pump single/multi stage as per actual head requirement as per

site situation.

The model of the pump with respect to head and discharge will be approved by EIC.

Pump should have following specifications: RS: Seventeen Thousand

(1) Minimum 10 mtr. Cu. flat cable of suitable size must be provided with pump. One Hundred Seven only

(2) Pump shall be installed as per manufacturer foundation/erection drawing or as per IS

specification.

(Body full C.I., stator winding- copper, rotor- copper, shaft- SS 304, motor-Energy

efficiency) (For Gardening Water)

91 Supplying and erecting approved make 3 HP DOL type motor control cubical panel made 1.00 Each

from 16 G. CRCA sheet duly epoxy powder painted inside and outside with hinged doors

and locking arrangement Floor Mounting On 300 mm Height with MS Stand Angle & CC

Foundation. Size 35 mm (H) x 35 mm (W) x 05 mm (D). The detail specification & quantity

of material used are as under. RS: Forty Six Thousand

Panel must be with minilec relay for auotmatic change over for pump 1 & 2 logically One Hundred Fifty Seven

without using manually change over switch (Minimum Panel Size: 1.10 meter (H) x 1.10 only

meter (W) x 0.25 meter (D).

INCOMMER SECTION: (1) MCCB-30 KA-FP (DU-100H), Rating: 63 Amp., Make: L&T,

Qty: 01 No. (2) Digital Ammeter (SR-65), Rating: 0-60 Amp., Make: Meco, Qty: 01 No. (3)

Rating: 6 Amp., Rotary, Make: Salzer, Qty: 01 No. (6) C.T.- Current Transformer, Rating:

60/5 Amp., Make: Virat, Qty: 03 Nos. (7) Indicating Lamps (R,Y,B), Rating: 22.5 mm LED,

Make: Airon, Qty:03 Nos. (8) SP MCB , Rating: 20 Amp., Make: L&T , Qty: 03 Nos. (9)

Control Wiring, Rating: 1.0 Sq.mm, Make: Any ISI, Qty: Lot (10) Copper Busbar, Rating:

63A/100 Amp., Qty: Lot (11) Numeric logical relay, Qty: 1 No.

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

Outgoing Feeder (3 HP DOL Feeder): Qty: 02 Nos. (1) MCB-FP-10 KA, Rating: 20 Amp.,

Make: L&T, Qty: 02 Nos. (2) Power Contactor (415 V) Main, Rating: 12 Amp., Make: L&T,

Qty: 02 Nos. (3) Over Load Relay, Rating: 6-10 Amp., Make: L&T, Qty: 02 Nos. (4) Digital

Ameter (SR-65), Rating: 0-20 Amp., Make: Meco, Qty: 02 Nos., (5) Digital Voltmeter (SR-65),

Rating: 0-500 V, Make: Meco, Qty: 02 Nos. (6) Indicating Lamps (Start,Run,Trip), Rating:

22.5 mm LED, Make: Airon, Qty: 04 Nos. (7) Push Button (Start,Stop), Rating: 22.5 mm,

Make: Airon, Qty: 04 Nos. (8) SPP, Rating: 415 V, Make: Space, Qty: 02 Nos. (9) Terminal,

Rating: As per Amp., Make: Airon, Qty: 04 Nos. (10) Control Wiring, Rating: 1.0 Sq.mm.,

Make: Any ISI, Qty: Lot (11) Power Wiring, Rating: As Per Amp., Make: Any ISI, Qty: Lot

Outgoing Feeder (6 Amp. - 01 No.) For Capacitor (1) MCB-FP-10 KA, Rating: 6 Amp., Make:

L&T, Qty: 01 No. (2) Capacitor- MPP Type, Rating: 2 KVAr, Make: Concap, Qty: 01 No., (3)

Power wiring, Rating: As Per Amp., Make: Any ISI, Qty:Lot

Outgoing Feeder (32 Amp. - 01 No.) For Lighting (1) MCB-FP-10 KA, Rating: 32 Amp.,

Make: L&T, Qty: 01 No. (2) Power wiring, Rating: As Per Amp. (3) Earthing Strip: 25 x 3;

G.I. Strip, Qty: 01 No. (4) MCB-DP-10KA , Rating: 20A, Make: L&T, Qty.:01 Nos.

92 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible 20.00 Mtr.

RS: One Hundred Three

copper cable approved make of following Size. [c] 3 Core x 2.5 Sq. mm

93 Providing & erecting ISI make medium duty (B class) galvanized MS pipe with coupling, 20.00 Mtr.

bend, union, reducer, tee, MS flange etc. with plumbing charges. 50 mm dia. [make and RS: Two Hundred Sixty

model approved by EIC strictly as per tender specification] only

94 Supplying and erecting C.I. Swing check type non-return (reflux) valve ISI marked with 3.00 No.

packing, flange, nuts and bolts etc.suitable for following pipe size. [a] For 50 mm dia. RS: One Thousand Ten

(Make and model approved by EIC as per specification only) Hundred Ten only

95 Lowering of existing submercible motor pump set complete with required No. and size of 2.00 Each

pipes by means of proper chain pulley block and pipe wrenches. Job includes stacking of

pipes cronologically after the checking of threads. [d] For open well horizontal submercible RS: Eight Hundred Forty

pump set for sump well. (ii) 1.0 HP to 5 HP Eight only

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

96 Providing and fixing of ABC Type Store Pressure Fire Extinguisher Having capacity 6 kg 2.00 Each

Filled with Mono Ammonium Phosphate Powder 50% confirms to IS 4308, Stored Pressure

Type, UGTS Pressure Gauge, Can Height 530 mm, Diameter 150 ± 10mm, Discharge Time

24 Sec, Controllable discharge mechanism, Jet Range 5 Meters, Average Discharge is 92%,

applicable on Class A,B & C and electrically started Fire, Fire Rating 4A:144B, Can

Construction : Deep drawn & CO2 Mig welded, EPDM(Ethylene Propylene Diene

Monomer) Rubber Hose with both end Aluminum clamped, Internal Coating - Epoxy

Powder coating, External Coating - Pure Polyester Powder coating (UV Resistant),Brass

forged CE Marked valves with NRV & Auto Safety Release with safety Pin is of SS

material, Made up from 1.6mm thick sheet, Extinguishers confirmed to IS 15683:2018 and

ISI marked. Referance Weight:-Gross Weight 8.9 Kg, Empty Weight 2.9 Kg, 1. Necessary

certificate & and guarantee must be attached, 2. OEM has to provide wall mounting heavy

duty bracket/clamp, screw, hardware for installation. 3.Following printed marking RS: One Thousand Nine

Manufacturing Date and Expiry Date must be mention on Extinguisher 4. Refilling period Hundred Ninty One only

must be of 3 Years. Following Printed marking on equipment must be required:- Model No,

Capacity, Gross Weight, Content, Fire Rating, Batch No, Serial no, Mfg Month, Refilling

Due. [with necessary numbering / marking with oil paint by painter as instructions given

by G.S.P.H.C.L engineer] (Make: KANEX, MINIMAX, CEASEFIRE)

Item Estimated Rate [Rs. Ps.] Amount

Description of Item Qty. Unit

No. InFigure In Words Rs.

97 Providing and fixing of CO2 type High Pressure Portable 4.5 kg Fire Extinguisher, filled 2.00 Each

with Co2 Gas as per IS 15222, Control discharge mechanism fitted with 1 Meter Wire

Braided Hose & Electrical non-conductor Polyethylene Flat Horn with Diffuser Nozzle for

dispersed discharge of CO2, Discharge Time 12 Sec, Average Discharge is 95%, Applicable

on Class B, C and electrically started Fire, Fire Rating 55B, Internal coating is not

applicable & External coating is of enamel spray painting, Powder Coated Handle, Valve

Confirm to IS 3224 ISI Marked, CO2 Cylinder construction: hot spinning by seamless pipes

& bearing ISI mark, Body confirms to IS 7285 and PESO ( Petroleum and Explosives Safety

Organization) APPROVED, Minimum Wall Thickness 4 to 4.2 mm, Extinguishers

confirmed to IS 15683:2018 and ISI marked. Referance Weight:-Gross Weight 16.4, empty

weight 11.9 Kg, 1. Necessary certificate & and guarantee must be attached, 2. OEM has to

provide wall mounting heavy duty bracket/clamp, screw, hardware for installation.

3.Following printed marking Manufacturing Date and Expiry Date must be mention on RS: Six Thousand Five

Extinguisher 4. Refilling period must be of 5 Years. Following Printed marking on Hundred Twenty Six only

equipment must be required:- Model No, Capacity, Gross Weight, Content, Fire Rating,

Batch No, Serial no, Mfg Month, Refilling Due. [with necessary numbering / marking with

oil paint by painter as instructions given by G.S.P.H.C.L engineer] (Make: KANEX,

MINIMAX, CEASEFIRE)

TOTAL ELE WORK Rs.

TOTAL CIVIL+ ELE WORK Rs.

Signature of Contractor Executive Engineer

Gujarat state police hous. corp. ltd, vadodara