PROVN OF BUS STOP AND WAITING AREA WITH ASSOCIATED DISPLAY SIGN BOARDS IN SOLMARA UNDER GE (N) TEZPUR

Note 1: (Applicable for all parts/items) : The bidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Excavating in trenches, n. exc 1.5 m wide and n. exc 1.5 m in depth; for foundation, etc. and getting out in soft/loose soil complete in all respect as specified and directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete in all respect as specified and directed.

Removing excavated material n. exc. 50m and depositing where directed at a level n. exc. 1.5 m above the starting point complete in all respect as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep geeting out in soft/loose soil complete in all respect as specifified and directed.

S&F steel work in tubular/square/rectangular hollow section/angle iron, tee etc. for structural trusses including special shaped washer etc. complete using ERW or induction butt welded tubes using Fe as per IS 4923, Grade YST 310 including necessary machinery for upto 10m height structure complete in all respect as specified and directed.

M&L for PCC (1:2:4) Type B-2 (40mm graded aggregate) as foundation filling and mass concrete for post complete in all respect as specifified and directed.

M&L for Broken stone or boulders hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete in all respect as specified and directed

Providing and laying for reinforced cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) in columns, posts, struts etc. complete in all respect as specifified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter in rough finished flat surface of concrete complete in all respect as specifified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished flat surface of concrete complete in all respect as specifified and directed.

S&F coloured 0.50mm thick pre- painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws with bitumen washer to truss members of any material complete in all respect as specifified and directed.

S&F for pre-coated galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L preparation of untreated new steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L 75 mm thick PCC (1:3:6) type C-2 using 40 mm nominal size crushed and graded stone aggregate laid in floor, path etc. or of similar type finished the surface even and fair without using extra cement complete in all respect as specified and directed.

M&L for roof top cover 6 to 8 mm thick colour multiwall polycarbonate roof sheet of approved colour as in roof covering/ cladding to wall, fixed with self tapping screws as specified .

S&F stainless steel (Grade 304) composite section of hollow pipe/tube, flat, plates, angle section, fancy pipe top caps etc. of for sign board welded with stainless steel rod, of any size, shape, description including welding, grinding, buffing, polishing and making curvature (wherever required) complete all as specified and directed.

M&L for ss 304 letter with acrylic letters including modular electric light attaiched of 30cm hight each letter and necessary scafolding arrangement complete in all respect as specified and directed.

S&F 3mm thick aluminium composite exterior grade plane panel sheet of approved colour size, shape, description for base of sign board including necessary stainless steel nut bolts fixed on stainless steel section complete all as specified and directed.

M&L for deformed TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete in all respect as specifified and directed.

M&L for deformed TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete in all respect as specifified and directed.

Providing & laying heavy duty non skid coloured digital printed floor tiles of size 300mmX300mm ,8 to 10mm thick set and jointed in neat cement slurry and pointed with white cement with pigment to match the tiles colour over and including 15mm thick screed bedding in cm 1:6 and dismentling of existing tiles/blocks of any discription complete in all respect as specified and directed.

M&L brick work with sub-class "B" old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:6) complete in all respect as specified and directed

M&L 15mm thick rendering on brick or concrete wall surfaces in cement mortar 1:4, finished even & smooth without using extra cement complete in all respect as specified and directed.

M&L for 20x20 inch LED Logo back ground 2 mm ACP sheet and letter 2mm acrylic including back side 4 mm sunboard and LED light and necessary fixing arrangement and design as approved by Engr in charge complete in all respect as specified and directed.

M&L for 75 mm thick PCC, type C-2, 1:3:6 (using 40 mm crushed and graded stone aggregate) as in plinth protection and finished surface even and smooth without using extra cement complete in all respect as specified and directed.

M&L for preparation of new plastered or undecorated surfaces of wall using wall care putty to fill the voids and applying two coats of weather coat over a coat of alkali resistant priming paint complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm multi stranded copper conductor 1100 V grade, ISI marked , PVC insulated unsheathed cable (with approved colour code) FRLSH cable drawn in & including PVC casing caping of 25/32 mm wide, with double locking type, including all accessories casing caping as approved by EIC, with PVC 1.5 mm multi stranded insulated unsheathed copper wire, ISI marked of green colour for continous earth, PVC terminal box and PVC board making good disturbed surface to match with the existing surface for one light /fan/bell point controlled by one switch complete all as directed by Engineer-In-charge.

All as per item 27 above but for One 3 pin socket outlet 5 Amps on same board.

All as per item 27 above but for One 3 pin switch socket combination 5 Amps on indpendent board

S&F switch piano (flush button type) single pole, one way, 5 Amps complete all as specified and directed.

S&F switch socket combination 2 in one, 5 pin , 5/6 Amps, 240 Volts flush type,complete all as specified and directed.

S&F of socket out let, 5 pin 5 Amps flush type complete all as specified and directed.

S&F of ceiling rose polycarbonate type three terminals complete all as specified and directed.

S&F LED Tube light luminaires, 20-22 watts, lumen output not lessthan 2000 (4 feet), made of anodised extruded aluminium housng, with high transmissivity diffuser, high lumen output, with suitable integrated electronic driver, and operated in single phase, 230 volts, 50HZ, all accessories internally pre-wired and including connecting up with three core twisted flexible copper conductor cable of from connector and ceiling rose, complete all as specified and directed.

M&L for Display sign boards at Bus stop incl LED backlit with driver and all accessories with suitable size as directed by Engr-in-Charge.

M&L for river sand, washed and screened dry for cushioning to under ground cable in tenches below and around under ground cable including spreading and levelling complete as specified and directed.

M&L laying well burnt old size bricks, sub calss "B" bricks, straight or curved on plan, laid flat with width equal to length of brick, laid dry over electric cablefor protection all complete all as specified and directed.

M&L for XLPE aluminium armoured cable of 25sqmm3.5core all complete as specified and directed.

S&F sheet metal enclosure double door for MCB DBs SPN 4 way 240 V, complete flush mounted all as specified and as directed.

S&F MCB single pole and neutral (SPN) 32 Amps, 240 volts , C curve , AC , 50 Hz ,10 kA complete all as specified and directed.

S&F MCB single pole (SP) 5 to 40 Amps, 240 volts , C curve , AC , 50 Hz ,10 kA complete all as specified and directed.

Supply & fixing Erecting Steel Hexagonal Pole Type 410-SP-31 (9.0 mtrs long) including Cast Iron Base Plate, Finial Taper Plug, Cap, Mild Steel Bolts, Nuts, Screws including applying two coats of Black Bituminous paint from bottom End of Pole upto PCC Coping and applying with two coats of Aluminium Paint over a coat of Primer (Externally from Top of Coping), including necessary earth work, excavation, PCC 1:3:6 using 40mm graded stone aggregate for foundation and coping with PCC 1:2:4 using 20mm stone aggregate and smooth finish complete all as specified and as directed.

Material and labour for junction boxes with new Thermoplastic Cable Junction Boxes IP66/67 "weather proof" , for outdoor installation with knockouts for cable entry with terminals suitable for 10-16sqmm cable off Size 155 X 210 X 92 mm incl busbar fixed in repairs and including Necessary civil works and connecting all incoming and outgoing wires with AL lugs of appropiate sizes and complete all as specified and directed by Engr-in-Charge.

M&L for PVC insulated weather proof sheated alluminium cable 2.5 Sqmm 2 core with 2.5 Sqmm single core for earthing complete all as specified and directed.

Supply and Fixing New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs as light source with secondary optics & exclusively designed polycarbonate cover alongwith electronic driver suitable for 32/40 mm dia bracket size of rating 65 W LED of make Philips/wipro/havells or of equivalent make complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Metre below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 15 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as shown on electrical plate No. 3 of SSR part - I including taking out old U/s complete alll as specified and directed .