IMPROVEMENT / UPGRADATION OF CERTAIN CAFETERIAS

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving n.exc 15cm thickness (below or above GL) as in floor etc. complete removal of debris outside MD land complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of brick work/PCC block masonry built in cement mortar or cement lime mortor including all quoins, arches, pillars etc., complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons laid bedded and pointed in any mortar etc, complete all as specified and as directed.

Taking down cement plaster on brick or concrete or stone walls of any description etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and as directed.

Taking down chowkats or frames not exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Taking down chowkats or frames exc 1.5 sqm but n.exc 4sqm each with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Taking down shutters of any description n. exc 1.00 sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1.00 but n. exc 2.00 sqm each complete all as specified and as directed.

Precast Cement concrete block masonry with solid blocks, type C1, 1:3:6 using 20 mm graded stone aggregate, exc 10 cm in width and setting in cement mortar 1:6, complete all as specified and as directed.

Precast Cement concrete block masonry with solid blocks, type C1, 1:3:6 using 20 mm graded stone aggregate, not exc 10 cm in width and setting in cement mortar 1:4, complete all as specified and as directed.

Precast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate, as in cover slab set and jointed in CM 1:6 including necessary form work complete all as specified and as directed. Note: Reinforcrment steel will be measured and paid seperately.

TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips,complete all as specified and as directed.

Rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and as directed.

M & L for 25mm thick PCC 1:2:4 type B-0 (using12.5 mm graded stone aggregate) as in sub base for floor finishes complete all as specifed and as directed.e.

Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles including 15mm thick screed bed CM 1:6 complete all as specified and as directed.

Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tiles including 15mm thick screed bed CM 1:6 complete all as specified and as directed.

Coloured glazed ceramic tiles in vertical surfaces such as skirting, dados and risers to steps etc., of size 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10mm thick backing coat CM 1:4 complete all as specified and as directed.

Granite (of any type) 18-20 mm thick, work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like including in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixtures of pigment to match with shade of granite complete all as specified and as directed.

S&F in repairs 15mm bore chromium plated cast copper alloy bib taps fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F 15mm bore chromium plated cast copper alloy bib taps fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F 15mm dia Pillar tap swan neck of brass, glossy finish complete all as specified and as directed.

S&F 15mm bore angle stop cock of chromium plated / brass, glossy finish complete all as specified and as directed

S&F tubular towel rail 20mm dia D type 60cm long between flanges chromium plated complete all as specified and as directed.

S&F Soap dish, brass chromium plated of suitable size, first quality, and fixed to plugs with chromium plated brass screws complete all as specified and as directed.

Taking up or down 15mm dia steel tubing and connections complete all as specified and as directed.

Taking up or down 20mm dia steel tubing and connections complete all as specified and as directed.

CPVC pipes SDR 11 of 20mm outer dia with plain CPVC SDR 11 fittings fixed on walls / ceilings or laying on floors complete all as specified and as directed.

CPVC pipes SDR 11 of 25mm outer dia with plain CPVC SDR 11 fittings fixed on walls / ceilings or laying on floors complete all as specified and as directed.

Taking down rain water pipes ( any size or pattern) including fittings complete all as specified and as directed.

S&F in repair PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc complete all as specified and as directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls / floor etc complete all as specified and as directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls / floor etc complete all as specified and as directed.

S&F PVC (SWR) bends 110mm dia any radius with access door complete all as specified and as directed.

S&F PVC (SWR) bends 75 mm dia any radius with access door complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single 'T') 110mm dia equal or unequal with access door complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single 'T') 75mm dia equal or unequal with access door complete all as specified and as directed.

S&F Stainless steel sink made out of 1.00mm thick sheet for kitchen with plug, washers, waste pipe, connecting union overall size 495mmx420mm with bowl size 410mmx330mmx160mm including 32mm bore PTMT Waste coupling, fixing in cement mortar on to dwarf wall or fixing cantilever brackets complete all as specified and as directed.

S&F in repairs Stainless steel sink made out of 1.00mm thick sheet for kitchen with plug, washers, waste pipe, connecting union overall size 495mmx420mm with bowl size 410mmx330mmx160mm including 32mm bore PTMT Waste coupling, fixing in cement mortar on to dwarf wall or fixing cantilever brackets complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin, size 550 X 400 mm (Flat Back or Angle Back type) including 32mm bore PTMT Waste coupling and PVC connection pipe of 15mm x 450mm long, a pair of angle iron brackets duly painted/ erecting stand including cutting and pinning in ends, making good disturbed surfaces in cement mortar 1:3, complete all as specified and as directed

Second class hardwood plain solid straight chowkats and frames wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

Factory made Second class hardwood glazed and skelton door shutters 35mm thick, open rebated and prepared to receive glass, gauze etc. with sash bar any number fitted with cut and mitred beads for securing glass gauze etc , sizes of members of shutters as specified in SSR Part I section 8, clause 8.24 (a) and fitted to chowkats, complete all as specified and as directed.

Factory made 30 mm thick flush shutters, solid core construction, with particle board core and ply wood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed.

Anodised aluminium frame powder coated (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc. complete all as specified as directed.

Anodized aluminium door shutters powder coated (minimum thickness of powder coating 50 micron), aluminium section weighing not less than 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos. in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified as directed.

Anodised aluminium window and ventilator shutters powder coated (minimum thickness of powder coating 50 micron), side hung / sliding type without sash bars, aluminium sections weighing not less than 0.55Kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws anodised aluminium fittings such as peg stays 150mm long (1 no.) hinges type B-21 100mm long (2 nos.) suitable handle (1 no.) complete all as specified and as directed.

Sheet glass 4mm thick ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and as directed.

Sheet glass 5.5mm thick, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete all as specified and as directed.

Sheet glass 5.5mm thick, ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and as directed.

12mm thick prelaminated particle board interior grade, one side laminated with decorative choice & other side balancing white lamination, fixed to Aluminium frame work for shutters of doors,cabinets etc., complete all as specified and as directed.

12mm thick prelaminated particle board interior grade, both side pre laminated with decorative choice fixed to Aluminium frame work for shutters of doors,cabinets etc., complete all as specified and as directed.

18 thick prelaminated particle board interior grade, one side laminated with decorative choice & other side balancing white lamination for shutters of cupboards,cabinets etc., including 1mm thick PVC edging all around of shutters and exposed surfaces complete all as specified and as directed.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to Aluminium or Steel frame complete all as specified and as directed.

S&F Butt hinges 100mm extruded aluminium alloy with mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed.

S&F aluminum anodised barrel tower bolts, bearing ISI mark, of extruded section 150mm long complete all as specified and as directed.

S&F aluminum anodised barrel tower bolts, bearing ISI mark, of extruded section 100mm long complete all as specified and as directed.

Aluminum anodised bow handle fabricated type extruded section of 100mm long complete all as specified and as directed.

Aluminum anodised bow handle fabricated type extruded section of 150mm long complete all as specified and as directed.

S&F 40mm dia cup boards knobs, brass bright finished fixed with nut, screws and washers complete all as specified and as directed.

300mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed..

150 mm over all length of cover plate of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, complete all as specified and as directed.

Aluminum anodised sliding door bolts of 300mm long with hasp and staple(bolt type) and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F continuous (Piano) hinges, width of flap in 30mm, mild steel bright finish or electro galvanized as specified and as directed.

Hasp and staple 100mm long, aluminium anodized including bolt to hinge plate and fixed with screws complete all as specified and as directed.

Magnet catches PVC body of 40mm size complete all as specified and as directed.

S&F mortice lock brass 4 levers vertical type, size 100mm complete all as specified and as directed.

S & F aluminium (die cast) body door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed.

S & F in repair anodised aluminium alloy curtain rods 25mm dia with suitable size of bracket complete all as specified and as directed.

Dismantling of wall and ceiling boards with frame work (fibre, pulp, insulation, etc) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

S & F False ceiling with anodized aluminium frame work with 605mm x 605mm size snap gird fixed with screws / staples using 36.5mm x 23.5mm x 1.5mm thick main tee, 23.5 x 23.5 x 1.28mm cross tee and 25x25x1.5mm angles fixed to perimeter of wall for false ceiling including necessary supporting hanger with 3.0mm dia GI wire and ‘J’ bolts washer nuts for securing frame work to ceiling suspended @ 120 cm C/C both ways, complete all as specified and as directed.

S & F 12mm thick, mineral fibre board/ tiles, fixed in ceiling, flat or sloping complete all as specified and as directed.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/ or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Complete removal of existing treatment of wall surfaces and applying 1mm thick wall care putty and applying two coats of oil bound distemper over one coat of primer including and preparation of surfaces complete all as specified and as directed .

Preparation of newly plastered wall surfaces and applying 1mm thick wall care putty and applying two coats of oil bound distemper over one coat of primer complete all as specified and as directed .

Complete removal of existing treatment of ceilings and applying two coats of oil bound distemper over one coat of primer complete all as specified and as directed .

Preparation of new wooden surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Preparation of new Steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old painted surfaces of wood and wood based materials of any description over 10cm girth or width not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of old painted surfaces of steel of any description over 10cm girth or width not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of new steel and iron surfaces of any description, n exc 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified and as directed .

Excavating in post holes (or similar holes) each n exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, removing excavated soil to a distance n.exc 50m and making good surface in Hard/dense soil complete all as specified and as directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Mild steel work in tubular post, trusses, including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 complete all as specified and as directed.

Mild steel flat iron for wind ties for roof including securing bolts, including all necessary drilling, bolting or riveting etc and similar work conforming to Fe 290 Gde E-165. complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour, having 550 Mpa tensile strength as in roof covering / cladding and fixed with self tapping screws, complete all as specified and as directed.

Taking down carefully existing copper/aluminium point wiring (light/fan/sockets/bell/power point) complete with all accessories such as switch with sheet, ceiling rose including rusted/broken concealed conduit, junction and sunken boxes etc and removing dismantled material and making good disturbed surface of walls/floors etc matching with existing surface complete all as specified and as directed.

Concealed point wiring for one light point/fan point /bell point controlled by one switch (using red, black and green colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through and including PVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes, 2mm thick galvanised steel pressed sunken box suitable for modular switch socket (Min 60mm deep, suitable length) concealed in wall, including inner and outer plates (cover plate) suitable for fixing the modular switches/ socket / regulator etc, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM 1:3 complete all as specified and as directed.

All as per above Srl item No. 88.00 but for one socket out let 5 Amps point controlled by one switch on same board complete all as specified and as directed.

All as per above Srl item No. 88.00 but for one socket out let 5 Amps point controlled by one switch on indipendent board and not below the any other switch board complete all as specified and as directed .

All as per above Srl item No. 88.00 here in before but for 15 amps socket outlet with 2.5 Sqmm Copper including 2.5 Sqmm FRLSH PVC insulated copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and as directed .

All as per above Srl item No. 88.00 here in before but for 15 Amps socket outlet with 4 Sqmm Copper including 4.0 Sqmm FRLSH PVC insulated copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and directed.

Taking down carefully existing copper/aluminium point wiring (light/fan/sockets points ) complete with all accessories such as switch with sheet, ceiling rose including rusted/broken concealed sunken boxes etc but except concealed conduit and junction boxes and removing dismantled material and making good disturbed surface of walls/floors etc matching with existing surface complete all as specified and as directed .

Concealed point wiring for one light point/fan point /bell point controlled by one switch (using red, black and green colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area) single core FRLSH PVC insulated unsheathed and multi strand copper conductor cable 1100 volt (ISI marked) drawn through existing PVC conduit but including 2mm thick galvanised steel pressed sunken box suitable modular switch socket (Min 60mm deep, suitable length) concealed in wall, including inner and outer plates (cover plate) suitable for fixing the modular switches / socket / regulator etc, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. complete all as specified and as directed. Note :- Where ever it is not feasible to cable drawn through existing PVC conduit (for ceiling fan point only) due to blocked, casing caping shall be provided by contractor without any extra cost and cost for the same shall is deemed to be included in the quoted unit rate.

Modular switch 1 way 6 amps, 1 module complete all as specified and as directed.

Modular switch 1 way 16 amps, 1 module complete all as specified and as directed.

Modular sockets 6 amps, 2/3 pin combined 2 module complete all as specified and as directed.

Modular sockets 6/16 amps, 2/3 pin combined 2 module complete all as specified and as directed.

lamp holder batten modular type PVC/Polycarbonate type with back plate including provision of 12 Watt LED bulb suitable for batten fittings complete all as specified and as directed.

Ceiling rose 3 terminals/phase type, fabricated of PVC/Polycarbonate, isolated body complete all as specified and as directed.

Point wiring with Television co-axial cable in and including concealed PVC conduit (25 mm dia) and conduit accessories and metal flush box of one module with cover fixed with screw and cap washers for Television point and making good all disturbed work to match the existing complete all as specified and as directed.

Modular type TV socket complete all as specified and as directed.

Submain wiring comprising single core two runs of 6 sqmm nominal cross sectional area multimultistranded copper conductor cable, FRLSH PVC insulated unsheathed 1100 Volts grade drawing through existing rigid non metallic PVC conduit pipe and accessories including provision of one run of 6.0 sqmm nominal cross sectional area multimultistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire and using color code as per IS and specified and making good all disturbed work to match the existing including taking down old sub main wiring complete all as specified and as directed.

Submain wiring comprising single core two runs of 4 sqmm nominal cross sectional area multimultistranded copper conductor cable, FRLSH PVC insulated unsheathed 1100 Volts grade drawing throgh in and including suitable size of rigid non metallic PVC conduit pipe and accessories including provision of one run of 4.0 sqmm nominal cross sectional area multimultistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire and using color code as per IS and specified and making good all disturbed work to match the existing including taking down old sub main wiring complete all as specified and as directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc ; and cutting chases for concealed water tubing or concealed wiring etc, and making good, cutting not exc 10 cm girth in brick walls complete all as specified and as directed.

LED tube light fitting of LED T5 tube lights (6500K) environmental friendly energy efficient of 20 Watt LED 230 Volt, AC decorative box type with driver,holder including electric connection with PVC copper flexible twin core cable, 1.0 sqmm from ceiling rose to light fitting including taking down old light fitting complete all as specified and as directed.

LED street light luminarie 35 watts with IP66 complete with pressure dia cast aluminium housing with GI pipe bracket made out of 25 mm dia medium grade pipe (60 cm long) bend to shape including fixing arrangement to wall with MS flat 25x3mm-2 Nos by nut, bolts and washers including electric connection with PVC copper flexible twin core cable 1.0 sqmm from ceiling rose to light fitting including taking down old light fitting complete all as specified and as directed.

LED light fitting mirror type with high out put diffuser 2 feet , 10 Watt 220 V AC decorative type with driver holder including connecting up with three core flexible copper conductor cable of suitable size including taking down old light fitting complete all as specified and as directed.

Sheet metal enclosure SPN DB having facility to fix MCB in incomer and MCBs in outgoing, SPN 8 way, double door type complete fitted with bus bars, neutral links, blanking plates including taking down old DB and making good disturbed surfaces complete all as specified and as directed.

Sheet metal enclosure TPN DB having facility to fix MCB in incomer and MCBs in outgoing, TPN 4 way, double door type complete fitted with bus bars, neutral links, blanking plates including taking down old DB and making good disturbed surfaces complete all as specified and as directed.

Protector and accessories for AC starter 25 A, 2 Module grouted flush to walls complete all as specified and as directed.

MCB, SP 6-32 amps 240 Volts and 10 KA breaking capacity, 'C' series type complete all as specified and as directed.

Isolator TPN 4 pole, 415 Volts, 63 amps and 16 KA breaking capacity, 'C' series complete all as specified and as directed.

Isolator, DP 32 amps 240 Volts complete all as specified.

Earthing complete with GI earth plate electrode of size 600x600x6 mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to GI wire 4 mm dia earth lead by means of nuts, bolts, check nuts, washers of galvanised iron as steel, protected by galvanized iron pipe 40mm bore (Medium grade) all as directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x10cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel, wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, earth testing point, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion all complete as specified and directed after taking down old earthing. Note : (i) Quoted rate deemed to include the cost or excavation and earth work PCC Chamber, funnel cover etc. (ii) GI wire 4 mm dia and GI Pipe 40 mm bore light grade up to 7.5m length deemed to be included in the rate quoted by the contractor.

Exhaust fans (Heavy duty) 300 mm sweep 230/240 volts single phase with self closing louvers GI off mode protection against birds etc including provision of cutting of walls suitabully for fixing exhaust fan and necessary plastering and making good the disturbed surface to match with existing complete all as specified and as directed.

LED light fitting recess/surface mounting mounted 2'x2' size flat panel of capacity 36 Watt IP20 made of CRCA sheet steel housing duly powder coated with high efficient PMMA diffuser soft glare free light complete with drivers, holder, suitable for roof ceilihg including connecting up with driver three core flexible copper conductor of suitable size complete including taking down old light fitting complete all as specified and directed.

Electric chimney black wall mounted 1350 CMH suitable for 4-5 burners, instant auto clean with heat/water on button, shine finish, curved glass stail less steel body, touch control,speed level 3 having LED light 02 Nos, of single phase AC 220 Volt, 50 Hz of size not less than 88 cmx 48.6 cmx 51.5 cm (L x D xH) and provide demonstrate the functionality and safety measures complete all as specified and directed. Make :- Hindware Skyla or equvalent make in of Crompton,Havells,V-guard,Whirlpool as approved by GE.

Wall mounted fan hi-speed 400 mm sweep (White color) single phase 230 volt, 50Hz, smooth oscillation & running, high speed motor for higher air delivery superior low voltage performance, aerodynamically designed balanced heavy duty PP blade complete all as specified and directed

famous construction