Interior and Renovation works of SIDBI Office, Mohali, Ankleshwar, Thiruvananthapuram and Varanasi

Total Amount 40,89,966.80

Total Amount 12,28,191.80

Net Total Amount In Rs = 1345445

S NO DESCRIPTION Amount

1 Civil Work 10,79,088.08

2 Electrical & Fire-Fighting Work 5,84,000.00

3 Air Conditioning 6,17,861.00

4 Furniture 13,73,640.00

Total Amount 36,54,589.08

Total Amount 36,54,589.08

Digitally signed by AMIT

Sn Item Description

Unit Qty Rate Amount

1 Providing and fixing false ceiling with gypsum board and frame work made of special section from M.S. sheet and consisting of

angle cleat at 1200mm c/c, one flange fixed to ceiling with dash fastener 12.5mm dia x50mm long with 6mm dia bolt, other

flange of cleat fixed to the angle hanger of 25x10x0.50mm of required length with nut & bolt of required size and other end of

angle hanger fixed with intermediate

G.I. channel 45x15x0.9mm running at spacing of 1200mm c/c, including fixing of gypsum board to ceiling section and perimeter

channel including jointing and finishing to a flush finish of tapered and square edge of board with jointing compound jointing

tape, and also including the cost of making opening for light fitting, grill, diffuser, cut-out made with frame of perimeter channel

suitably fixed, all complete.

2 Providing and making partly glazed /partly panelled laminated partition with galvanized steel internal frame work with 11mm

MDF board on either face laminated using 1.0mm laminate in required pattern. Rates are inclusive of s/f 8 mm clear glass in Sqm 44.11 5,428.00 2,39,429.08

glazed portion with required moulding ,polishing etc

2a Same as above but finishing of partition with 12 mm gypsum board on one side inplace of mdf and laminate.Rates are inclusive

of taping , jointing of gypboard all complete

3 Providing and fixing panelling with framing shall consist of GI Section on the wall. This framing would be covered by 11mm thick

MDF board with 1mm thick laminate .

4 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS

15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade.

DOOR & LAMINATION

5 Providing and fixing ISI marked flush door shutters 30mm thick conforming to IS : 2202 (Part I) decorative type, core of block

board construction with frame of 1st class hard wood.

6 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all

area of door shutter to be measured).

7 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of required dia & length.

8 Providing and fixing bright finished brass 100mm mortice lock with pair of handle /cylendrical lock with 6 levers

approved quality with necessary screws etc. complete. Nos 2.00 2,360.00 4,720.00

9 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564,

embossed on the body, door weight upto 35 kg and door width upto 700mm) with necessary accessories and screws etc. Nos 2.00 2,360.00 4,720.00

10 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as

per IS : 1868) transparent or dyed to required colour and shade, with necessary screw etc. complete. Nos 2.00 118.00 236.00

Digitally signed by AMIT

11 Providing & Fixing decorative high pressure laminated sheet of plain/wood grain in gloss/matt/suede finish with high density

protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of Sqm 0.00 1,000.00 0.00

adhesive of approved quality.

12 Providing and fixing 12mm thick frameless toughened glass door with all required ss hardware fittings-Single Shutter size

13 Providing and fixing 16mm thick mineral fibre false ceiling tiles of size 595X595mm. The tiles should in true horizontal level

suspended on interlocking T-Grid of hot dipped all round galvanized iron comprising of main T runners of 15x32mm of length

3000mm, cross T of size 15x32mm of length 1200mm and secondary intermediate cross T of size 15x32mm of length 600mm to

form grid module of size 600x600mm suspended from ceiling with adjuster of size 85x25x2mm, spaced at 1200mm centre to

centre along main ‘T’. The system should rest on periphery wall/partition with the help of GI perimeter wall angle to be fixed to

the wall with help of plastic rawl plug at 450mm centre to centre &

40mm long dry wall SS screw.

14 Providing & fixing Film on glasses of door & partition of selected design and colour all complete. Sqm 5.00 800.00 4,000.00

15 Providing and fixing Mettalic Logo of SIDBI behind public interface table including fixing of letters in hindi all complete.

16 Providing and fixing Zebra blind of approve colour fabric with all required powdercoated channel ,hardware material aluminium

clip ,pulling cord etc .all complete

17 P/F12 mm ply on external glazing portion for fixing of false

ceilingmembers i/c cutting ,wastage ,labour etc .all complete

18 Intensive cleaning of entire branch office premises with required material ,labour etc i/c all glass partition and its

section all complete L/S 1.00 5,000.00 5,000.00

19 S/F S.S patch lock and SS patch hinge for existing glass main doors which are damaged i/c removing and refixing of door.

Total Amount 10,79,088.08

Total Amount 10,79,088.08

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

Electrical work

Supplying, Laying, testing & commissioning of the

following size of XLPE Al. Conductor armoured

cables of 1.1KV grade on the surface of wall as

a 4 C x 6.0 Sqmm Cu. Cable Mtrs 160.00 400.00 64,000.00

b 1x 4.0 Sqmm Copper Wire Mtrs 200.00 85.00 17,000.00

DISTRIBUTION BOARDS

Supplying, installation, testing & commissioning of

following type wall mounted Horizontal TPN/SPN

distribution board of double door type design made

out of 16 gauge MS sheet with supplying and fixing

following accessories including painting,

interconnection, painting, earthing and labelling etc. as

Incoming 63Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18

Neutral links - 3 Nos (Separate for each phase)

Incoming 40Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18

Neutral links - 3 Nos (Separate for each phase)

Incoming 63Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) -

Neutral links - 3 Nos

5 63Amp. 4P, 25ka MCB with Box for UPS Set 1.00 2,500.00 2,500.00

Wiring for switch controlled light point with

3x1.5Sqmm PVC insulated FRLS multistrand copper

conductor 1100 Volt grade wires in PVC

surface/recessed conduit with accessories and

6 including the cost of supplying and fixing 6Amp 240

Volt grid plate mounted switch with moulded cover

plate in zinc chromate passivated MS box, and costing

circuit wiring with 3x2.5sqmm 1100volt grade PVC

insulated FRLS Multistrand

Primaryconductor

Point wires, in PVC conduit complete Pts. 32.00 950.00 30,400.00

b) Secondary Point Pts. 58.00 600.00 34,800.00

Digitally signed by AMIT

Wiring for 5pin 6A Light plug point with 3x1.5Sqmm Pts. 25.00 1,350.00 33,750.00

PVC insulated FRLS multistrand copper conductor

1100Volt grade wires in recessed FRLS PVC conduit

with accessories including the cost of providing &

7 fixing 1 No. Modular type 3pin 6A socket outlet

controlled by 6A switch in zinc chromate passivated

MS box, and circuit wiring with 3x2.5sqmm complete.

Wiring for following. 13A Socket controlled by 1No 16A Pts. 10.00 1,500.00 15,000.00

Switch with 3x2.5Sqmm PVC insulated FRLS multi

strand copper conductor 1100Volt grade wires in

8 recessed surface PVC conduit including the cost of

providing & fixing 1No Modular type 20A socket outlet

controlled by 1 No. 16A switch in zinc chromate

passivated MS box, complete.

Wiring for following. 16 A Power plug point controlled Pts. 8.00 2,200.00 17,600.00

by 1No 20A MCB with 2 x2.5 +1x1.5 Sqmm PVC

9 insulated FRLS multi strand copper conductor 1100Volt

grade wire in PVC conduit

complete. A.C Point

Concealed 16A+6A, socket combined power point as Pts. 9.00 1,700.00 15,300.00

10 UPS Point comprising of –3 Nos of 6/16 A

Universal Socket & 1 No.16A switch.

TELEPHONE SYSTEM

Supply and fixing of RJ-11 modular Telephone Pts. 12.00 500.00 6,000.00

outlet with Modular Plate

Supply & fixing the 50 pair telephone tag block of Nos 1.00 2,000.00 2,000.00

16 SWG Krone telephone tag block

Supplying & laying the 2 pair telephone wire of Mts 300.00 65.00 19,500.00

PVC insulated in PVC conduit recessed in wall

COMPUTER DATA NETWORKING

Supply and fixing flush steel box computer outlet Nos 22.00 1,450.00 31,900.00

point RJ-45 and cat-6 data cable complete

15.0 Supply and fixing 6U Rack Nos 1.00 8,000.00 8,000.00

16.0 supplying and fixing 12 port switch Nos 1.00 6,000.00 6,000.00

17.0 Supply and fixing 24 port Switch Nos 1.00 11,000.00 11,000.00

FANS FIXTURES & LIGHTS

Supplying, installation with hanging support, testing

and commissioning of following light fixtures with

electronic Ballasts, Tubes, lamps, all fixing materials

including connecting wires etc. all complete as per the

directions of Engineer-in- charge (All LED Light Fixtures

should be covered with minimum one year onsite

Recessed LED panel light (L1) (600X600MM) LED Nos 12.00 2,750.00 33,000.00

36watt 6500K in false ceiling RC 370 B

19 Recessed LED down light 15W (165DIA) DN 287 B Nos 25.00 1,050.00 26,250.00

20 Wall mounting fan 16 inch Nos 8.00 2,000.00 16,000.00

Digitally signed by AMIT

Providing, laying, testing and commissioning of 'C' class Sqm 158.00 675.00 1,06,650.00

heavy duty MS pipes confirming to IS:3589

/IS:1239 including welding, fittings like Elbow, Tee,

Flange, Nut bolt, Gasket etc. and fixing pipes to

wall/ceiling with suitable clamps and painting with two

21 or more coats of synthetic enamel paint complete as

required. Also include the UL Flexible Drop Pipe and

Pendent Type Sprinklers. Rate also include s/f butterfly

valve in main line for controlling supply.

Providing, laying, testing and commissioning Smoke Sqm 158.00 325.00 51,350.00

Detector, Heat Sensors, Fire Panels, hooter etc. with all

22 necessary fitting and cabling complete as directed.

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

Supply Installation, Testing & Commissioning of modular type

Variable Refrigerant Flow/Variable Refrigerant Volume air cooled

Outdoor units suitable for cooling and heating, having all

hermetically sealed inverter type Scroll Compressor(s), minimum

two compressors for above 14 HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R 410 A

Refrigerant, vibration isolators, with suitable foundation etc.

complete as required. The unit shall deliver the rated capacity at

1 AHRI Conditions and work even at 50°C ambient temperature Per HP 14 16415.00 229810.00

without tripping. The unit shall be suitable to work on 400V +/-

10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with

first charge of the refrigerant and ready for use as required. The

COP at AHRI conditions shall not be less than 3.1 and IEER not less

Supply, installation, testing and commissioning of following

minimum capacity 4-way flow VRV/VRF Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media pre-

filter, fan section with low noise fan/dynamically balanced blower,

multispeed motor, coil section with DX Copper coil, electronic

expansion valve, outer cabinet, drain pump, grill, necessary

supports, vibration isolation, cord less remote control etc., suitable

2 for operation on single phase 230 V ± 10%, 50Hz AC supply,

complete, as required. The unit shall have automatic force shut

down provision in case of fire on receiving signal from BMS

System. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature.

Supply, installation, testing and commissioning of following

minimum capacity VRV/VRF High wall type Indoor unit equipped

with washable synthetic media pre-filter, fan section with low

fan/dynamically balanced blower, multispeed motor, coil section

with DX copper coil, electronic expansion valve, outer cabinet, cord

less remote control, drain pan, necessary accessories etc., suitable

3 for operation on 230 V ± 10%, 50 Hz, single phase AC supply,

complete as required. The unit shall have automatic force shut

provision in case of fire on receiving signal from BMS System. The

cooling capacity of indoor unit will be at air inlet conditions of 27

Degree C DB and 19 Degree C WB temperature.

4 Refrigerant Piping

Digitally signed by AMIT

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes of

soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger

supports, jointing/brazing including accessories, insulated with

XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of specified

thickness as given below for Suction and Liquid lines, all

accessories as per specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19

mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with

19 mm thick insulation

28.5 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with

19 mm thick insulation

Lifting, Shifting, Supply, Installation, Testing & Commissioning of

Interconnecting "Y" & "T" Joints i.e. Refnet Joints/ Header with

5 Insulation for refrigearnt piping

Providing & laying of uPVC drain Pipe 25 mm to drain out the

6 water as per the site requirement Metre 60 295.00 17700.00

Supplying and drawing following sizes of FRLS PVC insulated

7 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Total 617861.00

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

2 seater Dimension(L)1390mm X (D)750mm X (H)710mm nos 2 37800 75,600

Supplying, and placing in position of sofa with premium Leatherette upholstery adds

class to the soft cushioned backrest and seating. Material & subtype:Premium

Leatherette, Colour & Colour Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone.

steam beech solid wood have used for framing construction of sofa .The seat cushion

is made of multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 &

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting

stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of

2 DGM High Back Chair nos 1 14500 14,500

Supplying and placing in position of 360 degrees revolving high back chair . The chair

of Size :-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be

ergonomically design contour lumbar back design made of 12mm thick BWR plywood

(IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The

chrome plated loop armrest with padded upholstery is provided for extra comfort. The

chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0

+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-

35 (+/-2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

3 DGM Visitor Back Chair nos 3 7000 21,000

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X

(D)505mm X (H)990mm.A contemporary design with an all black finish, . Material &

subtype:Premium Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X

(D)505mm X (H)990mm, Back Type:Cantilever, Base:Cantilever Frame, Base

Type:Cantilever, Maximum Seating Height:19".The Seat & back are made up of 12mm

thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has

foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

4 Conference Medium Back Chair nos 9 8500 76,500

Supplying and placing in position of 360 degrees revolving medium back chair . The

Craze chair of Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall

be ergonomically design contour lumbar back design made of 12mm thick BWR

plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam.

The chair shall be provided with pneumatic height adjustment which shall have stroke of

10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of

density 30-35 (+/-2kg /m3) The backrest has a foam of 28kg/m3.

5 AGM High Back Chair nos 1 13575 13,575

Supplying and placing in position of 360 degrees revolving high back chair of size:

660mm (L) x 490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm

thick water proof plywood and moulded foam. The seat to be made with 12 mm thick hot

pressed BWR plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh

fabric over it. The chair shall be provided with self tension single locking mechanism and

pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm .The black .The

pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be

operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot

pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of

density 32-35 kg/m3. The backrest has a foam of 28kg/m3. adjustable arm rest and

6 Medium Back Chair (work station & conference room) nos 10 7500 75,000

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Supplying and placing in position of 360 degrees revolving medium back chair. The

breathable mesh back chair with cushioned fabric seat shall be ergonomically design

with adjustable lumbar back support . The chair shall be provisioned with adjustable

armrest (Up-Down) with PP padding and Adjustable Headrest(Can Adjust Movement).

The chair shall be provided with self tension single locking mechanism and pneumatic

height adjustment which shall have stroke of 10.0 +/- 0.3 cm .The pneumatic height

adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs

extension force.The Seat are made up of 12mm thk hot pressed plywood upholstered

with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

7 AGM Visitor Chair & conference room side chairs nos 2 7000 14,000

Supplying and placing in position of Fix cantilever chair,the chair made of full mesh in

black colour.. use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for

seat).Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for

best quality cushioning in seat, back: frame of design shall be curved made of two

pieces injection moulded frame cover with mesh .backrest support adjustable lumbar

support. Only seat size is 500mm(l)x 500mm(d)x 470mm(h) & the back size is

465mm(l)x 550mm(h) ,Seat max height is @ 470mm .Fixed cantilever chair .base:

chrome plated tubular frame of cantilever type..The Seat are made up of 12mm thk hot

pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of

density 32-35 kg/m3.

8 Modular Workstation

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) nos 5 29925 1,49,625

Modular Workstation With Side Top with 3 drawer Pedestal Size 1500W x 600D x

750/1200H.Partition NI-60mm Partition Ht. 1200mm, Double Raceway systems Skirting

label and below the table top . lower tile both side laminated and upper tile inside side

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick

Gabel end 18mm thick MDF board., and 3Drawer top supported Pedestal unit Size

400W x 400D x 725H made in 18mm thick..Complete Made in MDF Board.. Laminate 1-

Frosty White, Laminate2 For drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue,

Powder Coating-Munshel Gray. and White Tinted Glass

9 Linear Workstation

Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) nos 4 21735 86,940

Supplying, and placing in position of linear workstation as per Image.The worktop made

out of 25mm thk. Prelam Particle board with 2 mm thk PVC edge banding.The Table top

supported on Mild Steel of size 50mm x50mm Slanted Leg and 50mm x 25mm

Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk Metal

panel fixed on both side of the "T" leg for Vertical wire carrying purpose.(Sharing

Workstation). 0.8 mm thk Single/Double metal powder coated raceway with Powder

coting of 50 Micron below top for wiring.Vertical wire carrying pole with powder coating

50 micron below top for wiring( Non- sharing workstation ). Also having a provision of ms

perfoated sheet hanging modesty. provision of glass divider rest on the "D" brackets on

the table top between opposite seatings. All working or non working edges shall be

provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Provision of pullout PVC keyboard tray and CPU trolley for each seating.

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a

combination of 2 drawer & one filing drawer. The pedestal storage unit shall be made of

18 mm thick prelaminated Particle board with provision of handles & Locking

Main Table Dimension (L) 1650mm x (D) 750mm x (H) 750mm

Side Runer Dimension (L) 1050mm X (D) 450mm X (H) 750mm

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Supplying, and placing in position of main Table as per Image/ drawing.The Table top

are made out of 25mm thk prelam particle board with 2mm thk pvc edge banding & side

panel & modesty panel made up of 18mm thick pre-laminated particle board .The

working edges shall be provided with machine pressed 2mm thick PVC edging using

special hot melt glue at hot temperature. The table have a provision of free standing

Side Storage of size 1050mm L x 450mm D x 750mm Ht., Storage Top made out of

25mm thick pre laminated particle board and rest all storage to be made out of 18 mm

thick prelaminated particle board . All exposed edges shall be provided with machine

pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Storage having a

provision of 3 drawer unit, two openable shutter with D shape handle & central locking

Main Table Dimension (L)1800mm X (D) 900mm X (H)750mm

overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

Supplying and placing in position of main table as per photograph/drawing .The table

shall be made out of 25mm thick pre -laminated particle board of approved shade. The

working and non working edges shall be finished with machine pressed with 2mm PVC

egdge banding. The table top shall be supported with MS powder coated "C" shape leg

of size 50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are

made out of 18mm thick prelaminated particle board with 2mm thk pvc edge banding.

The table shall be provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x

675mm(H) . Side storage having a provision for three equal drawer unit and two

openable shutter & one open storage with shelf in it. The Side unit top shall be made

out of 18mm thick pre laminated particle board and rest all storage to be made out of

18mm thick pre laminated particle board. Provision of Junction box, wire raceway and 6

module fliptop box for wire passing or as per site requirement.

12 Medium Height Partition

Supplying and placing in position of sliding tile base modular Workstation as per

photograph. Free standing partition height 1200mm and should be minimum of 62-

67mm thick. Partition inner frame is 1.0-1.2mm thick mild steel. Horizontal and vertical

trims are made out of extruded aluminum of 1mm thick. All Panels/trims shall be powder

coated with 50 micron. Aluminum trims are elegantly fixed with hidden connectors on the

partition. The frame work shall be fitted with 9mm thick pre laminated Particle tiles of

approved shade. Partition shall have provision for pin up board with fabric/ white marker/

laminated of approved shade. Partition framework shall have adequate provisions for

the movement of electric data cables at desired 2 levels; one at skirting and another

above / below the table top. The complete partitioning work shall be carried out as per

the approved drawing. The product should be as per above given specification under the

guidance of project Engineer in charge.

13 Conference Table

Supplying and placing in position of conference table of required size as per

image/drawing. The work surface top should be of thickness 42mm top prelaminated

particle board with 2mm thick PVC edge banding. The side panel are made up of 36mm

thick prelaminated particle & modesty panel are made out of 25mm thick prelaminated

particle board with 2mm thick PVC edge banding. The wire carrier should be made

from 0.6mm thick CRCA & powder coated 40-50 microns. Also having a provision of 6

module flip top box & metal raceway for wire flow.

14 Pantry Table

Providing & Installation of Pantry table of size 1.83 m x 0.75m x 1.05m (ht) made out of

19mm thk. Commercial Board finished in Recon veneer and DU Pont Coreanof

approved shade as per design. The Recon surfaces to be white Duco painted. A glass

top od width 0.2m on SS pegs to be provided above table. One (1) number Drawer nos. 1.00 25000.00 25,000

pedestal with 3 drawers to be provided under the table.

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Providing & Installation of Pantry chairs of required dimension and as per instruction of

16 Openable Shutter storage

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back

panel is made of 09mm thick MDF of approved shade. All the edges of storage surface

shall be provided with machine pressed imported PVC lipping glued with hot melt EVA

glue free from any VOC with free groove handle and suitable lock. All exposed area

PVC edge lipping

Net Total Amount In Rs = 1373640

Net Total Amount In Rs = 1373640

Digitally signed by AMIT

Interior Fit out works in the office space of SIDBI-ANKLESHWAR

S NO DESCRIPTION Amount

1 Civil Work 9,74,497.18

2 Electrical & Fire-Fighting Works 3,16,356.75

3 Air Conditioning 4,94,916.00

4 Furniture 8,96,170.00

Total Amount INCLUDING GST 26,81,939.93

Total Amount INCLUDING GST 26,81,939.93

Digitally signed by AMIT

Sn Item Description

Unit Rate Amount

1 Providing and fixing false ceiling with gypsum board and frame work made of special section from M.S. sheet and consisting of

angle cleat at 1200mm c/c, one flange fixed to ceiling with dash fastener 12.5mm dia x50mm long with 6mm dia bolt, other flange

of cleat fixed to the angle hanger of 25x10x0.50mm of required length with nut & bolt of required size and other end of angle

hanger fixed with intermediate

G.I. channel 45x15x0.9mm running at spacing of 1200mm c/c, including fixing of gypsum board to ceiling section and perimeter Sqm 65.00 1,450.00 94,250.00

channel including jointing and finishing to a flush finish of tapered and square edge of board with jointing compound jointing tape,

and also including the cost of making opening for light fitting, grill, diffuser, cut-out made

with frame of perimeter channel suitably fixed, all complete.

2 Providing and making partly glazed /partly panelled laminated partition with galvanized steel internal frame work with 11mm

MDF board on either face laminated using 1.0mm laminate in required pattern. Rates are inclusive of s/f 8 mm clear glass in

glazed portion with required moulding

2a Same as above but finishing of partition with 12 mm gypsum board on one side inplace of mdf and laminate.Rates are

inclusive of taping , jointing of gypboard all complete Sqm 51.00 4,000.00 2,04,000.00

3 Providing and fixing panelling with framing shall consist of GI Section on the wall. This framing would be covered by 11mm

thick MDF board with 1mm thick laminate . Sqm 28.00 2,550.00 71,400.00

4 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS

15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade.

DOOR & LAMINATION

5 Providing and fixing ISI marked flush door shutters 30mm thick conforming to IS : 2202 (Part I) decorative type, core of block

board construction with frame of 1st class hard wood.

6 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters

(over all area of door shutter to be measured). Sqm 1.89 212.00 400.68

7 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of required Cum 0.30 1,00,000.0 30,000.00

8 Providing and fixing bright finished brass 100mm mortice lock with pair of handle /cylendrical lock with 6 levers

approved quality with necessary screws etc. complete. Nos 1.00 2,360.00 2,360.00

Digitally signed by AMIT

9 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS

: 3564, embossed on the body, door weight upto 35 kg and door width upto 700mm) with necessary accessories and

screws etc. complete. Nos 1.00 2,360.00 2,360.00

10 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per

IS : 1868) transparent or dyed to required colour Nos 1.00 118.00 118.00

and shade, with necessary screw etc. complete.

11 Providing & Fixing decorative high pressure laminated sheet of plain/wood grain in gloss/matt/suede finish with high density

protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including

cost of adhesive of approved quality.

12 Providing and fixing 12mm thick frameless toughened glass door with all required ss hardware fittings-Single Shutter size

13 Providing and fixing 16mm thick mineral fibre false ceiling tiles of size 595X595mm. The tiles should in true horizontal level

suspended on interlocking T-Grid of hot dipped all round galvanized iron comprising of main T runners of 15x32mm of length

3000mm, cross T of size 15x32mm of length 1200mm and secondary intermediate cross T of size 15x32mm of length 600mm to

form grid module of size 600x600mm suspended from ceiling with adjuster of size 85x25x2mm, spaced at 1200mm centre to

centre along main ‘T’. The system should rest on periphery wall/partition with the help of GI perimeter wall angle to be fixed to

the wall with help of plastic rawl plug at 450mm centre to centre &

40mm long dry wall SS screw.

14 Providing & fixing Film on glasses of door & partition of selected design and colour all complete. Sqm 6.40 800.00 5,120.00

15 Providing and fixing Mettalic Logo of SIDBI behind public interface table including fixing of letters in hindi all complete.

16 Providing and fixing Zebra blind of approve colour fabric with all required powdercoated channel ,hardware material aluminium

clip ,pulling cord etc .all complete

17 P/F12 mm ply on external glazing portion for fixing of false

ceilingmembers i/c cutting ,wastage ,labour etc .all complete

18 Intensive cleaning of entire branch office premises with required material ,labour etc i/c all glass partition and its

section all complete L/S 1.00 5,000.00 5,000.00

19 S/F S.S patch lock and SS patch hinge for existing glass main doors which are damaged i/c removing and refixing of door.

Total Amount 9,74,497.18

Total Amount 9,74,497.18

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

Electrical work

Supplying, Laying, testing & commissioning of the

following size of XLPE Al. Conductor armoured

cables of 1.1KV grade on the surface of wall as required

a 4 C x 6.0 Sqmm Cu. Cable Mtrs 10.00 400.00 4,000.00

b 1x 4.0 Sqmm Copper Wire Mtrs 10.00 85.00 850.00

DISTRIBUTION BOARDS

Supplying, installation, testing & commissioning of

following type wall mounted Horizontal TPN/SPN

distribution board of double door type design made out

of 16 gauge MS sheet with supplying and fixing

following accessories including painting,

interconnection, painting, earthing and labelling etc. as

Incoming 63Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18

Neutral links - 3 Nos (Separate for each phase)

Incoming 40Amp TPN MCB (10KA) - 1 No 0.00

Busbar 100 Amp TPN copper busbar - 1 Set 0.00

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18 0.00

Neutral links - 3 Nos (Separate for each phase) 0.00

Incoming 63Amp TPN MCB (10KA) - 1 No 0.00

Busbar 100 Amp TPN copper busbar - 1 Set 0.00

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 0.00

Neutral links - 3 Nos 0.00

5 63Amp. 4P, 25ka MCB with Box for UPS Set 1.00 2,500.00 2,500.00

POINT WIRING 0.00

Wiring for switch controlled light point with 3x1.5Sqmm 0.00

PVC insulated FRLS multistrand copper conductor 1100

Volt grade wires in PVC surface/recessed conduit with

accessories and including the cost of supplying and

6 fixing 6Amp 240 Volt grid plate mounted switch with

moulded cover plate in zinc chromate passivated MS

box, and costing circuit wiring with 3x2.5sqmm 1100volt

grade PVC insulated FRLS Multistrand

copper conductor wires, in PVC conduit complete

a) Primary Point Pts. 20.00 950.00 19,000.00

b) Secondary Point Pts. 18.00 600.00 10,800.00

Digitally signed by AMIT

Wiring for 5pin 6A Light plug point with 3x1.5Sqmm PVC Pts. 30.00 1,350.00 40,500.00

insulated FRLS multistrand copper conductor 1100Volt

grade wires in recessed FRLS PVC conduit with

7 accessories including the cost of providing & fixing 1 No.

Modular type 3pin 6A socket outlet controlled by 6A

switch in zinc chromate passivated MS box,

and circuit wiring with 3x2.5sqmm complete.

Wiring for following. 16A Socket controlled by 1No 16A Pts. 9.00 1,500.00 13,500.00

Switch with 3x2.5Sqmm PVC insulated FRLS multi strand

copper conductor 1100Volt grade wires in recessed

8 surface PVC conduit including the cost of providing &

fixing 1No Modular type 20A socket outlet controlled by

1 No. 16A switch in zinc chromate passivated MS

Wiring for following. 16 A Power plug point controlled Pts. 10.00 2,200.00 22,000.00

by 1No 20A MCB with 2 x2.5 +1x1.5 Sqmm PVC

9 insulated FRLS multi strand copper conductor 1100Volt

grade wire in PVC conduit

UPS WIRING A.C Point 0.00

Concealed 16A+6A, socket combined power point as Pts. 12.00 1,700.00 20,400.00

10 UPS Point comprising of –3 Nos of 6/16 A

Universal Socket & 1 No.16A switch.

TELEPHONE SYSTEM 0.00

Supply and fixing of RJ-11 modular Telephone Pts. 9.00 500.00 4,500.00

outlet with Modular Plate

Supply & fixing the 20 pair telephone tag block of Nos 1.00 2,000.00 2,000.00

16 SWG Krone telephone tag block

Supplying & laying the 2 pair telephone wire of Mts 100.00 65.00 6,500.00

PVC insulated in PVC conduit recessed in wall

COMPUTER DATA NETWORKING

Supply and fixing flush steel box computer outlet Nos 10.00 1,450.00 14,500.00

point RJ-45 and cat-6 data cable complete

15.0 Supply and fixing 6U Rack Nos 1.00 8,000.00 8,000.00

16.0 supplying and fixing 12 port switch Nos 1.00 6,000.00 6,000.00

17.0 Supply and fixing 24 port Switch Nos 1.00 11,000.00 11,000.00

FANS FIXTURES & LIGHTS

Supplying, installation with hanging support, testing and

commissioning of following light fixtures with electronic

Ballasts, Tubes, lamps, all fixing materials including

connecting wires etc. all complete as per the directions

of Engineer-in- charge (All LED Light Fixtures should be

covered with minimum one year onsite replacement

Recessed LED panel light (L1) (600X600MM) LED Nos 13.00 2,750.00 35,750.00

36watt 6500K in false ceiling RC 370 B

19 Recessed LED down light 15W (165DIA) DN 287 B Nos 20.00 1,050.00 21,000.00

20 Wall mounting fan 16 inch Nos 5.00 2,000.00 10,000.00

Digitally signed by AMIT

Providing, laying, testing and commissioning of 'C' class Sqm 0.00 675.00 0.00

heavy duty MS pipes confirming to IS:3589

/IS:1239 including welding, fittings like Elbow, Tee,

Flange, Nut bolt, Gasket etc. and fixing pipes to

wall/ceiling with suitable clamps and painting with two

21 or more coats of synthetic enamel paint complete as

required. Also include the UL Flexible Drop Pipe and

Pendent Type Sprinklers. Rate also include s/f butterfly

valve in main line for controlling supply.

Providing, laying, testing and commissioning Smoke Sqm 84.79 325.00 27,556.75

Detector, Heat Sensors, Fire Panels, hooter etc. with all

22 necessary fitting and cabling

complete as directed.

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

SITC Cassette fan coil unit (water cooled )

1.5 TR hydronic Cassette fan coil unit (water cooled) with remote

1 control Nos 58240.00 0.00

2.0 TR hydronic cassette fan coil unit (water cooled )with remote

2 control Nos 59904.00 0.00

4omm m.s c class pipe

VS -2 with 2 way on/off valve

25 mm Ball valve

Installation Charges

25 mm m.s pipe C- class pipe i/c welding

7 ,testing etc. complete Mtr 885.00 0.00

8 25 mm pvc Drain Pipe Mtr 259.60 0.00

9 Insulation on M.S pipe & drain pipe Mtr 247.80 0.00

Brass Y strainer

Electrical connection and testing &

11 commissioning of system Nos 1770.00 0.00

12 Transportation Charges no.s 4500.00 0.00

Supply Installation, Testing & Commissioning of modular type

Variable Refrigerant Flow/Variable Refrigerant Volume air cooled

Outdoor units suitable for cooling and heating, having all

hermetically sealed inverter type Scroll Compressor(s), minimum

two compressors for above 14 HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R 410 A

Refrigerant, vibration isolators, with suitable foundation etc.

complete as required. The unit shall deliver the rated capacity at

1 AHRI Conditions and work even at 50°C ambient temperature Per HP 0 16415.00 0.00

without tripping. The unit shall be suitable to work on 400V +/-

10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with

first charge of the refrigerant and ready for use as required. The

COP at AHRI conditions shall not be less than 3.1 and IEER not less

Digitally signed by AMIT

Supply, installation, testing and commissioning of following

minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling

mounted unit equipped with synthetic washable media pre-filter,

fan section with low noise fan/dynamically balanced blower,

multispeed motor, coil section with DX Copper coil, electronic

expansion valve, outer cabinet, drain pump, grill, necessary

supports, vibration isolation, cord less remote control etc., suitable

for operation on single phase 230 V ± 10%, 50Hz AC supply,

complete, as required. The unit shall have automatic force shut

down provision in case of fire on receiving signal from BMS System.

The cooling capacity of indoor unit will be at air inlet conditions of

27 Degree C DB and 19 Degree C WB temperature.

Supply, installation, testing and commissioning of following capacity

Intertor Split ACl type Indoor unit equipped with washable

synthetic media pre-filter, fan section with low noise

fan/dynamically balanced blower, multispeed motor, coil section

3 with DX copper coil, electronic expansion valve, outer cabinet, cord

less remote control, drain pan, necessary accessories etc., suitable

for operation on 230 V ± 10%, 50 Hz, single phase AC supply,

complete as required.

4 Refrigerant Piping

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes of

soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger

supports, jointing/brazing including accessories, insulated with XPLE

Class-O tubular insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness as

given below for Suction and Liquid lines, all accessories as per

specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19

mm thick insulation

Lifting, Shifting, Supply, Installation, Testing & Commissioning of

Interconnecting "Y" & "T" Joints i.e. Refnet Joints/ Header with

5 Insulation for refrigearnt piping

Providing & laying of uPVC drain Pipe 25 mm to drain out the water

as per the site requirement

Digitally signed by AMIT

Supplying and drawing following sizes of FRLS PVC insulated

copper conductor, single core cable in the existing surface/

7 recessed steel/ PVC conduit as required.

Total 494916.00

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

3 seater Dimension : (L)1650mm X (D)750mm X (H)710mm nos 0 46800 0

2 seater Dimension(L)1390mm X (D)750mm X (H)710mm nos 1 37800 37,800

Supplying, and placing in position of sofa with premium Leatherette

upholstery adds class to the soft cushioned backrest and seating. Material &

subtype:Premium Leatherette, Colour & Colour Family:as per requirement,

Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact,

Style:Modern, Texture:Two Tone. steam beech solid wood have used for

framing construction of sofa .The seat cushion is made of multi layered foam of

density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic

webbing. The thread used is nylon bonded to provide lasting stitch strength .

The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200

2 DGM High Back Chair nos 0 14500 0

Supplying and placing in position of 360 degrees revolving high back chair .

The chair of Size :-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The

chair shall be ergonomically design contour lumbar back design made of 12mm

thick BWR plywood (IS Grade - 303 for seat and back) upholstered with

leatheritte and cut foam. The chrome plated loop armrest with padded

upholstery is provided for extra comfort. The chair shall be provided with

pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five

star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-

2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

3 DGM Visitor Back Chair nos 0 7000 0

Supplying and placing in position of medium back cantilever chair of size:

(W)610mm X (D)505mm X (H)990mm.A contemporary design with an all black

finish, . Material & subtype:Premium Leatherette, Colour & Colour Family:Black,

Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

Base:Cantilever Frame, Base Type:Cantilever, Maximum Seating

Height:19".The Seat & back are made up of 12mm thk hot pressed plywood

upholstered with PVC with polyurethane foam, chair seat has foam of density

32-35 kg/m3. The backrest has a foam of 28kg/m3.

4 Conference Medium Back Chair nos 0 8500 0

Supplying and placing in position of 360 degrees revolving medium back chair .

The Craze chair of Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm.

The chair shall be ergonomically design contour lumbar back design made of

12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered with

leatheritte and cut foam. The chair shall be provided with pneumatic height

adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base

with nylon castors . Chair seat has foam of density 30-35 (+/-2kg /m3) The

backrest has a foam of 28kg/m3.

5 AGM High Back Chair nos 1 13575 13,575

Supplying and placing in position of 360 degrees revolving high back chair of

size: 660mm (L) x 490mm(D) x 1315mm(H). The seat cushion to be

upholstered on 10-12mm thick water proof plywood and moulded foam. The

seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303)

upholsetered with Polyurethane foam and mesh fabric over it. The chair shall

be provided with self tension single locking mechanism and pneumatic height

adjustment which shall have stroke of 10.0 +/- 0.3 cm .The black .The

pneumatic height adjustment shall have adjustment stroke of 100 mm and shall

be operated at 30kgs extension force.The Seat & back are made up of 12mm

thk hot pressed plywood upholstered with PVC with polyurethane foam, chair

seat has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

adjustable arm rest and head rest

6 Medium Back Chair (work station & Conference ) nos 15 7500 1,12,500

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Supplying and placing in position of 360 degrees revolving medium back chair.

The breathable mesh back chair with cushioned fabric seat shall be

ergonomically design with adjustable lumbar back support . The chair shall be

provisioned with adjustable armrest (Up-Down) with PP padding and Adjustable

Headrest(Can Adjust Movement). The chair shall be provided with self tension

single locking mechanism and pneumatic height adjustment which shall have

stroke of 10.0 +/- 0.3 cm .The pneumatic height adjustment shall have

adjustment stroke of 100 mm and shall be operated at 30kgs extension

force.The Seat are made up of 12mm thk hot pressed plywood upholstered

with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

7 AGM Visitor Chair & conference room side chairs nos 3 7000 21,000

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Supplying and placing in position of Fix cantilever chair,the chair made of full

mesh in black colour.. use of ply: 12 mm thick hot pressed bwr plywood (is

grade - 303 for seat).Seat: 40 ± 2 mm thick polyurethane foam with density 32

(±3) kg per cu meter for best quality cushioning in seat, back: frame of design

shall be curved made of two pieces injection moulded frame cover with mesh

.backrest support adjustable lumbar support. Only seat size is 500mm(l)x

500mm(d)x 470mm(h) & the back size is 465mm(l)x 550mm(h) ,Seat max

height is @ 470mm .Fixed cantilever chair .base: chrome plated tubular frame

of cantilever type..The Seat are made up of 12mm thk hot pressed plywood

upholstered with PVC with polyurethane foam, chair seat has foam of density

8 Modular Workstation

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) nos 4 29925 1,19,700

Modular Workstation With Side Top with 3 drawer Pedestal Size 1500W x

600D x 750/1200H.Partition NI-60mm Partition Ht. 1200mm, Double Raceway

systems Skirting label and below the table top . lower tile both side laminated

and upper tile inside side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H

25mm thick Gabel end 18mm thick MDF board., and 3Drawer top supported

Pedestal unit Size 400W x 400D x 725H made in 18mm thick..Complete Made

in MDF Board.. Laminate 1-Frosty White, Laminate2 For drawer Facia-

Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-Munshel Gray. and

White Tinted Glass

9 Linear Workstation

Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) nos 2 21735 43,470

Supplying, and placing in position of linear workstation as per Image.The

worktop made out of 25mm thk. Prelam Particle board with 2 mm thk PVC

edge banding.The Table top supported on Mild Steel of size 50mm x50mm

Slanted Leg and 50mm x 25mm Horizontal connectors with Powder coting of

50 Micron.Middle Leg :- 0.8 mm thk Metal panel fixed on both side of the "T"

leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk

Single/Double metal powder coated raceway with Powder coting of 50 Micron

below top for wiring.Vertical wire carrying pole with powder coating 50 micron

below top for wiring( Non- sharing workstation ). Also having a provision of ms

perfoated sheet hanging modesty. provision of glass divider rest on the "D"

brackets on the table top between opposite seatings. All working or non

working edges shall be provided with machine pressed 2mm thick PVC edging

using special hot melt glue at hot temperature. Provision of pullout PVC

keyboard tray and CPU trolley for each seating. Also a provision of Pedestal

Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2 drawer

& one filing drawer. The pedestal storage unit shall be made of 18 mm thick

prelaminated Particle board with provision of handles & Locking arrangement

Main Table Dimension (L) 1650mm x (D) 750mm x (H) 750mm

Side Runer Dimension (L) 1050mm X (D) 450mm X (H) 750mm

Supplying, and placing in position of main Table as per Image/ drawing.The

Table top are made out of 25mm thk prelam particle board with 2mm thk pvc

edge banding & side panel & modesty panel made up of 18mm thick pre-

laminated particle board .The working edges shall be provided with machine

pressed 2mm thick PVC edging using special hot melt glue at hot temperature.

The table have a provision of free standing Side Storage of size 1050mm L x

450mm D x 750mm Ht., Storage Top made out of 25mm thick pre laminated

particle board and rest all storage to be made out of 18 mm thick

prelaminated particle board . All exposed edges shall be provided with machine

pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Storage having

a provision of 3 drawer unit, two openable shutter with D shape handle &

central locking arrangement.

Main Table Dimension (L)1800mm X (D) 900mm X (H)750mm

overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Supplying and placing in position of main table as per photograph/drawing .The

table shall be made out of 25mm thick pre -laminated particle board of

approved shade. The working and non working edges shall be finished with

machine pressed with 2mm PVC egdge banding. The table top shall be

supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm

thick prelaminated particle board with 2mm thk pvc edge banding. The table

shall be provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x

675mm(H) . Side storage having a provision for three equal drawer unit and

two openable shutter & one open storage with shelf in it. The Side unit top

shall be made out of 18mm thick pre laminated particle board and rest all

storage to be made out of 18mm thick pre laminated particle board. Provision

of Junction box, wire raceway and 6 module fliptop box for wire passing or as

per site requirement.

12 Medium Height Partition

Supplying and placing in position of sliding tile base modular Workstation as

per photograph. Free standing partition height 1200mm and should be

minimum of 62-67mm thick. Partition inner frame is 1.0-1.2mm thick mild steel.

Horizontal and vertical trims are made out of extruded aluminum of 1mm thick.

All Panels/trims shall be powder coated with 50 micron. Aluminum trims are

elegantly fixed with hidden connectors on the partition. The frame work shall be

fitted with 9mm thick pre laminated Particle tiles of approved shade. Partition Sqft 40 1400 56000

shall have provision for pin up board with fabric/ white marker/ laminated of

approved shade. Partition framework shall have adequate provisions for the

movement of electric data cables at desired 2 levels; one at skirting and

another above / below the table top. The complete partitioning work shall be

carried out as per the approved drawing. The product should be as per above

given specification under the guidance of project Engineer in charge.

13 Conference Table

Supplying and placing in position of conference table of required size as per

image/drawing. The work surface top should be of thickness 42mm top

prelaminated particle board with 2mm thick PVC edge banding. The side panel

are made up of 36mm thick prelaminated particle & modesty panel are made

out of 25mm thick prelaminated particle board with 2mm thick PVC edge

banding. The wire carrier should be made from 0.6mm thick CRCA & powder

coated 40-50 microns. Also having a provision of 6 module flip top box & metal

raceway for wire flow.

14 Pantry Table

Providing & Installation of Pantry table of size 1.83 m x 0.75m x 1.05m (ht)

made out of 19mm thk. Commercial Board finished in Recon veneer and DU

Pont Coreanof approved shade as per design. The Recon surfaces to be white

Duco painted. A glass top od width 0.2m on SS pegs to be provided above nos. 1.00 25000.00 25,000

table. One (1) number Drawer pedestal with 3 drawers to be provided under the

Providing & Installation of Pantry chairs of required dimension and as per

instruction of EIC

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

16 Openable Shutter storage

The storage top 25 mm thick, shutter and side panels are made of 18mm thick

and back panel is made of 09mm thick MDF of approved shade. All the edges

of storage surface shall be provided with machine pressed imported PVC

lipping glued with hot melt EVA glue free from any VOC with free groove

handle and suitable lock. All exposed area PVC edge lipping

Net Total Amount In Rs = 896170

Net Total Amount In Rs = 896170

Digitally signed by AMIT

Interior Fit out works in the office space of SIDBI-Trivendram

S NO DESCRIPTION Amount

1 Civil Work 915,638.00

2 Electrical & Fire-Fighting Work 486,800.00

3 Air Conditioning 733,462.00

4 Furniture 730,330.00

Total Amount 2,866,230.00

Total Amount 2,866,230.00

Digitally signed by AMIT

Sn Item Description

Unit Qty Rate Amount

1 Providing and fixing false ceiling with gypsum board and frame work made of special section from M.S. sheet and consisting of

angle cleat at 1200mm c/c, one flange fixed to ceiling with dash fastener 12.5mm dia x50mm long with 6mm dia bolt, other flange

of cleat fixed to the angle hanger of 25x10x0.50mm of required length with nut & bolt of required size and other end of angle

hanger fixed with intermediate

G.I. channel 45x15x0.9mm running at spacing of 1200mm c/c, including fixing of gypsum board to ceiling section and perimeter Sqm 85.00 1,450.00 123,250.00

channel including jointing and finishing to a flush finish of tapered and square edge of board with jointing compound jointing tape,

and also including the cost of making opening for light fitting, grill, diffuser, cut-out made

with frame of perimeter channel suitably fixed, all complete.

2 Providing and making partly glazed /partly panelled laminated partition with galvanized steel internal frame work with 11mm MDF

board on either face laminated using 1.0mm laminate in required pattern. Rates are inclusive of s/f 8 mm clear glass in glazed

portion with required moulding

2a Same as above but finishing of partition with 12 mm gypsum board on one side inplace of mdf and laminate.Rates are

inclusive of taping , jointing of gypboard all complete Sqm 44.51 4,000.00 178,040.00

3 Providing and fixing panelling with framing shall consist of GI Section on the wall. This framing would be covered by 11mm

thick MDF board with 1mm thick laminate . Sqm 51.00 2,550.00 130,050.00

4 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS

15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade.

DOOR & LAMINATION

5 Providing and fixing ISI marked flush door shutters 30mm thick conforming to IS : 2202 (Part I) decorative type, core of

block board construction with frame of 1st class hard wood. Sqm 10.00 3,450.00 34,500.00

6 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters

(over all area of door shutter to be measured). Sqm 8.00 212.00 1,696.00

7 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of required Cum 0.55 100,000.0 55,000.00

8 Providing and fixing bright finished brass 100mm mortice lock with pair of handle /cylendrical lock with 6 levers

approved quality with necessary screws etc. complete. Nos 5.00 2,360.00 11,800.00

Digitally signed by AMIT

9 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS

: 3564, embossed on the body, door weight upto 35 kg and door width upto 700mm) with necessary accessories and

screws etc. complete. Nos 5.00 2,360.00 11,800.00

10 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per

IS : 1868) transparent or dyed to required colour Nos 5.00 118.00 590.00

and shade, with necessary screw etc. complete.

11 Providing & Fixing decorative high pressure laminated sheet of plain/wood grain in gloss/matt/suede finish with high density

protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including

cost of adhesive of approved quality.

12 Providing and fixing 12mm thick frameless toughened glass door with all required ss hardware fittings-Single Shutter size

13 Providing and fixing 16mm thick mineral fibre false ceiling tiles of size 595X595mm. The tiles should in true horizontal level

suspended on interlocking T-Grid of hot dipped all round galvanized iron comprising of main T runners of 15x32mm of length

3000mm, cross T of size 15x32mm of length 1200mm and secondary intermediate cross T of size 15x32mm of length 600mm to

form grid module of size 600x600mm suspended from ceiling with adjuster of size 85x25x2mm, spaced at 1200mm centre to

centre along main ‘T’. The system should rest on periphery wall/partition with the help of GI perimeter wall angle to be fixed to

the wall with help of plastic rawl plug at 450mm centre to centre &

40mm long dry wall SS screw.

14 Providing & fixing Film on glasses of door & partition of selected design and colour all complete. Sqm 4.00 800.00 3,200.00

15 Providing and fixing Mettalic Logo of SIDBI behind public interface table including fixing of letters in hindi all complete.

16 Providing and fixing Zebra blind of approve colour fabric with all required powdercoated channel ,hardware material aluminium

clip ,pulling cord etc .all complete

17 P/F12 mm ply on external glazing portion for fixing of false

ceilingmembers i/c cutting ,wastage ,labour etc .all complete

18 Intensive cleaning of entire branch office premises with required material ,labour etc i/c all glass partition and its

section all complete L/S 1.00 5,000.00 5,000.00

19 S/F S.S patch lock and SS patch hinge for existing glass main doors which are damaged i/c removing and refixing of door.

Total Amount 915,638.00

Total Amount 915,638.00

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

Electrical work

Supplying, Laying, testing & commissioning of the

following size of XLPE Al. Conductor armoured

cables of 1.1KV grade on the surface of wall as

a 4 C x 6.0 Sqmm Cu. Cable Mtrs 80.00 400.00 32,000.00

b 1x 4.0 Sqmm Copper Wire Mtrs 220.00 85.00 18,700.00

DISTRIBUTION BOARDS

Supplying, installation, testing & commissioning of

following type wall mounted Horizontal TPN/SPN

distribution board of double door type design made

out of 16 gauge MS sheet with supplying and fixing

following accessories including painting,

interconnection, painting, earthing and labelling etc.

Incoming 63Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18

Neutral links - 3 Nos (Separate for each phase)

Incoming 40Amp TPN MCB (10KA) - 1 No 0.00

Busbar 100 Amp TPN copper busbar - 1 Set 0.00

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18 0.00

Neutral links - 3 Nos (Separate for each phase) 0.00

Incoming 63Amp TPN MCB (10KA) - 1 No 0.00

Busbar 100 Amp TPN copper busbar - 1 Set 0.00

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 0.00

Neutral links - 3 Nos 0.00

5 63Amp. 4P, 25ka MCB with Box for UPS Set 1.00 2,500.00 2,500.00

POINT WIRING 0.00

Wiring for switch controlled light point with 0.00

3x1.5Sqmm PVC insulated FRLS multistrand copper

conductor 1100 Volt grade wires in PVC

surface/recessed conduit with accessories and

6 including the cost of supplying and fixing 6Amp 240

Volt grid plate mounted switch with moulded cover

plate in zinc chromate passivated MS box, and costing

circuit wiring with 3x2.5sqmm 1100volt grade PVC

insulated FRLS Multistrand

Primaryconductor

Point wires, in PVC conduit complete Pts. 30.00 950.00 28,500.00

b) Secondary Point Pts. 60.00 600.00 36,000.00

Digitally signed by AMIT

Wiring for 5pin 6A Light plug point with 3x1.5Sqmm Pts. 30.00 1,350.00 40,500.00

PVC insulated FRLS multistrand copper conductor

1100Volt grade wires in recessed FRLS PVC conduit

7 with accessories including the cost of providing &

fixing 1 No. Modular type 3pin 6A socket outlet

controlled by 6A switch in zinc chromate passivated

Wiring for following. 13A Socket controlled by 1No Pts. 9.00 1,500.00 13,500.00

16A Switch with 3x2.5Sqmm PVC insulated FRLS multi

strand copper conductor 1100Volt grade wires in

8 recessed surface PVC conduit including the cost of

providing & fixing 1No Modular type 20A socket outlet

controlled by 1 No. 16A switch in zinc chromate

Wiring for following. 16 A Power plug point controlled Pts. 18.00 2,200.00 39,600.00

by 1No 20A MCB with 2 x2.5 +1x1.5 Sqmm PVC

9 insulated FRLS multi strand copper conductor

1100Volt grade wire in PVC conduit

UPS WIRING A.C Point 0.00

Concealed 16A+6A, socket combined power point as Pts. 11.00 1,700.00 18,700.00

10 UPS Point comprising of –3 Nos of 6/16 A

Universal Socket & 1 No.16A switch.

TELEPHONE SYSTEM 0.00

Supply and fixing of RJ-11 modular Telephone Pts. 9.00 500.00 4,500.00

outlet with Modular Plate

Supply & fixing the 30 pair telephone tag block of Nos 1.00 2,000.00 2,000.00

16 SWG Krone telephone tag block

Supplying & laying the 2 pair telephone wire of Mts 200.00 65.00 13,000.00

PVC insulated in PVC conduit recessed in wall

COMPUTER DATA NETWORKING

Supply and fixing flush steel box computer outlet Nos 10.00 1,450.00 14,500.00

point RJ-45 and cat-6 data cable complete

15.0 Supply and fixing 6U Rack Nos 1.00 8,000.00 8,000.00

16.0 supplying and fixing 12 port switch Nos 1.00 6,000.00 6,000.00

17.0 Supply and fixing 24 port Switch Nos 1.00 11,000.00 11,000.00

FANS FIXTURES & LIGHTS

Supplying, installation with hanging support, testing

and commissioning of following light fixtures with

electronic Ballasts, Tubes, lamps, all fixing materials

including connecting wires etc. all complete as per the

directions of Engineer-in- charge (All LED Light

Fixtures should be covered with minimum one year

onsite replacement

Recessed LED panel light (L1) (600X600MM) LED Nos 11.00 2,750.00 30,250.00

36watt 6500K in false ceiling RC 370 B

19 Recessed LED down light 15W (165DIA) DN 287 B Nos 25.00 1,050.00 26,250.00

20 Wall mounting fan 16 inch Nos 5.00 2,000.00 10,000.00

Digitally signed by AMIT

Providing, laying, testing and commissioning of 'C' Sqm 95.30 675.00 64,327.50

class heavy duty MS pipes confirming to IS:3589/IS:

1239 including welding, fittings like Elbow, Tee,

Flange, Nut bolt, Gasket etc. and fixing pipes to

wall/ceiling with suitable clamps and painting withtwo

21 or more coats of synthetic enamel paint completeas

required. Also include the UL Flexible Drop Pipeand

Pendent Type Sprinklers. Rate also include s/f

butterfly valve in main line for controlling supply.

Providing, laying, testing and commissioning Smoke Sqm 95.30 325.00 30,972.50

Detector, Heat Sensors, Fire Panels, hooter etc. with

22 all necessary fitting and cabling

complete as directed.

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

SITC Cassette fan coil unit (water cooled )

1.5 TR hydronic Cassette fan coil unit (water cooled) with remote

1 control Nos 58240.00 0.00

2.0 TR hydronic cassette fan coil unit (water cooled )with remote

2 control Nos 59904.00 0.00

4omm m.s c class pipe

VS -2 with 2 way on/off valve

25 mm Ball valve

Installation Charges

25 mm m.s pipe C- class pipe i/c welding

7 ,testing etc. complete Mtr 885.00 0.00

8 25 mm pvc Drain Pipe Mtr 259.60 0.00

9 Insulation on M.S pipe & drain pipe Mtr 247.80 0.00

Brass Y strainer

Electrical connection and testing &

11 commissioning of system Nos 1770.00 0.00

12 Transportation Charges no.s 4500.00 0.00

Supply Installation, Testing & Commissioning of modular type

Variable Refrigerant Flow/Variable Refrigerant Volume air cooled

Outdoor units suitable for cooling and heating, having all

hermetically sealed inverter type Scroll Compressor(s), minimum

two compressors for above 14 HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R 410 A

Refrigerant, vibration isolators, with suitable foundation etc.

1 complete as required. The unit shall deliver the rated capacity at Per HP 14 16415.00 229810.00

AHRI Conditions and work even at 50°C ambient temperature

without tripping. The unit shall be suitable to work on 400V +/-

10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with

first charge of the refrigerant and ready for use as required. The

COP at AHRI conditions shall not be less than 3.1 and IEER not less

Digitally signed by AMIT

Supply, installation, testing and commissioning of following

minimum capacity 4-way flow VRV/VRF Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media

pre-filter, fan section with low noise fan/dynamically balanced

blower, multispeed motor, coil section with DX Copper coil,

electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration isolation, cord less remote control

etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC

supply, complete, as required. The unit shall have automatic force

shut down provision in case of fire on receiving signal from BMS

System. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature.

Supply, installation, testing and commissioning of following

minimum capacity VRV/VRF High wall type Indoor unit equipped

with washable synthetic media pre-filter, fan section with low

fan/dynamically balanced blower, multispeed motor, coil section

with DX copper coil, electronic expansion valve, outer cabinet,

3 less remote control, drain pan, necessary accessories etc., suitable

for operation on 230 V ± 10%, 50 Hz, single phase AC supply,

complete as required. The unit shall have automatic force shut

provision in case of fire on receiving signal from BMS System. The

cooling capacity of indoor unit will be at air inlet conditions of 27

Degree C DB and 19 Degree C WB temperature.

4 Refrigerant Piping

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes of

soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger

supports, jointing/brazing including accessories, insulated with

XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of specified

thickness as given below for Suction and Liquid lines, all

accessories as per specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

19 mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19

mm thick insulation

Lifting, Shifting, Supply, Installation, Testing & Commissioning of

Interconnecting "Y" & "T" Joints i.e. Refnet Joints/ Header with

Insula on for refrigearnt piping

Providing & laying of uPVC drain Pipe 25 mm to drain out the

water as per the site requirement

Digitally signed by AMIT

Supplying and drawing following sizes of FRLS PVC insulated

copper conductor, single core cable in the existing surface/

7 recessed steel/ PVC conduit as required.

Total 733462.00

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

3 seater Dimension : (L)1650mm X (D)750mm X (H)710mm nos 0 46800 0

2 seater Dimension(L)1390mm X (D)750mm X (H)710mm nos 1 37800 37,800

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as per

requirement, Seating Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern,

Texture:Two Tone. steam beech solid wood have used for framing construction of sofa .The seat cushion is

made of multi layered foam of density 32-35 kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic

webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest has a foam of

28kg/m3 with polyster polyfill outer layer of 200 gsm.

2 DGM High Back Chair nos 1 14500 14,500

Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size :-(W)590mm X

(D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour lumbar back design made

of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The

chrome plated loop armrest with padded upholstery is provided for extra comfort. The chair shall be provided

with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon

castors . Chair seat has foam of density 30-35 (+/-2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

3 DGM Visitor Back Chair nos 3 7000 21,000

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

(H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette, Colour &

Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever, Base:Cantilever

Frame, Base Type:Cantilever, Maximum Seating Height:19".The Seat & back are made up of 12mm thk hot

pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

The backrest has a foam of 28kg/m3.

4 Conference Medium Back Chair nos 11 8500 93,500

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-

(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour lumbar back

design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and

cut foam. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3

cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-2kg /m3) The backrest

has a foam of 28kg/m3.

5 AGM High Back Chair nos 1 13575 13,575

Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x 490mm(D) x

1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof plywood and moulded foam. The

seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303) upholsetered with Polyurethane

foam and mesh fabric over it. The chair shall be provided with self tension single locking mechanism and

pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height

adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force.The Seat &

back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat

has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

6 Medium Back Chair (work station & Conference ) nos 5 7500 37,500

Supplying and placing in position of 360 degrees revolving medium back chair. The breathable mesh back chair

with cushioned fabric seat shall be ergonomically design with adjustable lumbar back support . The chair shall be

provisioned with adjustable armrest (Up-Down) with PP padding and Adjustable Headrest(Can Adjust

Movement). The chair shall be provided with self tension single locking mechanism and pneumatic height

adjustment which shall have stroke of 10.0 +/- 0.3 cm .The pneumatic height adjustment shall have adjustment

stroke of 100 mm and shall be operated at 30kgs extension force.The Seat are made up of 12mm thk hot

pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

7 AGM Visitor Chair & conference room side chairs nos 6 7000 42,000

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Supplying and placing in position of Fix cantilever chair,the chair made of full mesh in black colour.. use of ply:

12 mm thick hot pressed bwr plywood (is grade - 303 for seat).Seat: 40 ± 2 mm thick polyurethane foam with

density 32 (±3) kg per cu meter for best quality cushioning in seat, back: frame of design shall be curved made

of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support. Only seat

size is 500mm(l)x 500mm(d)x 470mm(h) & the back size is 465mm(l)x 550mm(h) ,Seat max height is @ 470mm

.Fixed cantilever chair .base: chrome plated tubular frame of cantilever type..The Seat are made up of 12mm thk

hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

8 Modular Workstation

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) nos 2 29925 59,850

Modular Workstation With Side Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-

60mm Partition Ht. 1200mm, Double Raceway systems Skirting label and below the table top . lower tile both

side laminated and upper tile inside side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end 18mm thick

MDF board., and 3Drawer top supported Pedestal unit Size 400W x 400D x 725H made in 18mm

thick..Complete Made in MDF Board.. Laminate 1-Frosty White, Laminate2 For drawer Facia-Honkong Blue,

Fabric-F 161 Dolphin Blue, Powder Coating-Munshel Gray. and White Tinted Glass

9 Linear Workstation

Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) nos 3 21735 65,205

Supplying, and placing in position of linear workstation as per Image.The worktop made out of 25mm thk. Prelam

Particle board with 2 mm thk PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm

Slanted Leg and 50mm x 25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk

Metal panel fixed on both side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk

Single/Double metal powder coated raceway with Powder coting of 50 Micron below top for wiring.Vertical wire

carrying pole with powder coating 50 micron below top for wiring( Non- sharing workstation ). Also having a

provision of ms perfoated sheet hanging modesty. provision of glass divider rest on the "D" brackets on the table

top between opposite seatings. All working or non working edges shall be provided with machine pressed 2mm

thick PVC edging using special hot melt glue at hot temperature. Provision of pullout PVC keyboard tray and

CPU trolley for each seating. Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a

combination of 2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick

prelaminated Particle board with provision of handles & Locking arrangement

Main Table Dimension (L) 1650mm x (D) 750mm x (H) 750mm

Side Runer Dimension (L) 1050mm X (D) 450mm X (H) 750mm

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Supplying, and placing in position of main Table as per Image/ drawing.The Table top are made out of 25mm

thk prelam particle board with 2mm thk pvc edge banding & side panel & modesty panel made up of 18mm thick

pre-laminated particle board .The working edges shall be provided with machine pressed 2mm thick PVC edging

using special hot melt glue at hot temperature. The table have a provision of free standing Side Storage of size

1050mm L x 450mm D x 750mm Ht., Storage Top made out of 25mm thick pre laminated particle board and rest

all storage to be made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided

with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Storage having a provision of 3

drawer unit, two openable shutter with D shape handle & central locking arrangement.

Main Table Dimension (L)1800mm X (D) 900mm X (H)750mm

overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out of 25mm

thick pre -laminated particle board of approved shade. The working and non working edges shall be finished with

machine pressed with 2mm PVC egdge banding. The table top shall be supported with MS powder coated "C"

shape leg of size 50mm x 50mm with connectors of size 40mm x 40mm. The front modesty are made out of

18mm thick prelaminated particle board with 2mm thk pvc edge banding. The table shall be provisioned with

Side unit of overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal

drawer unit and two openable shutter & one open storage with shelf in it. The Side unit top shall be made out

of 18mm thick pre laminated particle board and rest all storage to be made out of 18mm thick pre laminated

particle board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

12 Medium Height Partition

Supplying and placing in position of sliding tile base modular Workstation as per photograph. Free standing

partition height 1200mm and should be minimum of 62-67mm thick. Partition inner frame is 1.0-1.2mm thick mild

steel. Horizontal and vertical trims are made out of extruded aluminum of 1mm thick. All Panels/trims shall be

powder coated with 50 micron. Aluminum trims are elegantly fixed with hidden connectors on the partition. The

frame work shall be fitted with 9mm thick pre laminated Particle tiles of approved shade. Partition shall have Sqft 40 1400 56000

provision for pin up board with fabric/ white marker/ laminated of approved shade. Partition framework shall have

adequate provisions for the movement of electric data cables at desired 2 levels; one at skirting and another

above / below the table top. The complete partitioning work shall be carried out as per the approved drawing.

The product should be as per above given specification under the guidance of project Engineer in charge.

13 Conference Table

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

Supplying and placing in position of conference table of required size as per image/drawing. The work surface

top should be of thickness 42mm top prelaminated particle board with 2mm thick PVC edge banding. The side

panel are made up of 36mm thick prelaminated particle & modesty panel are made out of 25mm thick

prelaminated particle board with 2mm thick PVC edge banding. The wire carrier should be made from 0.6mm

thick CRCA & powder coated 40-50 microns. Also having a provision of 6 module flip top box & metal raceway

14 Pantry Table

Providing & Installation of Pantry table of size 1.83 m x 0.75m x 1.05m (ht) made out of 19mm thk. Commercial

Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The Recon surfaces to

be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above table. One (1) number nos. 1.00 25000.00 25,000

Drawer pedestal with 3 drawers to be provided under the table.

15 Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC nos. 8.00 2200.00 17,600

16 Openable Shutter storage

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made of 09mm

thick MDF of approved shade. All the edges of storage surface shall be provided with machine pressed imported

PVC lipping glued with hot melt EVA glue free from any VOC with free groove handle and suitable lock. All

exposed area PVC edge lipping

Net Total Amount In Rs = 730330

Net Total Amount In Rs = 730330

Digitally signed by AMIT