REPAIR MAINT TO FENCING HARD STANDING STONE PITCHING ROAD BERMS AND ALLIED WORKS UNDER AGE B RI MAINT AT INA EZHIMALA

Amount

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for providing pre cast reinforced cement concrete type B-l, 1:2:4 (20 mm graded aggregate) as in drain cover slabs complete all as specified and as directed. Note:- Reinforcement will be measured and paid separately.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engr-in-Charge.

Demolition of plain cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for 100 mm thick plain cement concrete type D-2, (1:4:8) (40mm graded aggregate) as in subbase complete all as specified and as directed.

M&L for 100 mm thick plain cement concrete type B-1, (1:2:4) (20mm graded aggregate) as in hard standing finished the surface even and smooth complete all as specified and as directed.

Excavating in trenches, n.exc. 1.50m wide and n.exc. 1.5m in depth, for foundation, etc. or for shafts, wells, cesspits, manholes pier holes, etc. n exc. 10 sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n.exc 25cm complete all as specified and as directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed.

M&L for Pre-cast cement concrete block masonry type C1 1:3:6 (using 20 mm aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar (1:6), complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. Note:- All dismantled materials shall be removed without any delay and stacked at places where directed without any extra cost to the Govt..

Dismantling expanded metal/chain link fencing any thickness or mesh, fixed with steel or wood fillets, if any not exc 4 kg/Sqm complete all as specified and as directed. Note:- All dismantled materials shall be removed without any delay and stacked at places where directed without any extra cost to the Govt.

Excavation in post holes (or similar holes) each n exc 0.5 cum getting out in hard/dense soil and removing the soil upto a distance of 50 m where directed complete all as specified and as directed.

S&F MS poles, tubular sections including all necessary drilling, welding, bolting or riveting, etc., and similiar work conforming to Fe-290 Gde E-165, complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

S&F PVC coated chain link fencing ( mesh 50 mm x 50 mm size) nominal dia of wire 3 mm ( including PVC coating ) fixed to fencing posts using suitable bolts and nuts (nuts and bolts shall be measured seperately) complete all as specified and as directed.

Fixing only PVC coated chain link fencing of any description using suitable bolts and nuts (nuts and bolts shall be measured seperately) complete all as specified and as directed.

S&F Mild steel screw bolt (machine made) 5 to 10 mm dia of neck with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm long n exc 10 cm long complete all as specified and as directed.

Demolition of laterite stone pitching/ masonry of any description, built in cement mortar incl all quoins, arches, pillars etc but excl ashlars facings, dressed stonework & precast concrete articles complete all as specified and as directed.

M&L for laterite stone pitching/ masonry of squared rubble, regular coursed, well bonded, bedded and solidly hearted, jointed and pointed in cement mortar 1:6 complete all as specified and as directed.

M&L for rendering 15mm thick CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

S&F framed work as in doors or gates or ladders or staging for water tanks or any MS works of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete confirming to Fe- 410 W (grade E-250 quality-A) complete all as specified and as directed by Engr-in-Charge.

M&L of sand or baby chips filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick on ground to receive interlock tiles complete all as specified and directed by Engineer in charge.

S&F Prepolished machine pressed precast concrete interlocking paver block of approved shape, colour and size confirming to IS-15658-2006 of 60mm thickness, M-35 Grade complete laid dry using machine compaction as specified and directed by Engineer in charge.

M&L for cement concrete machine pressed chequered tiles of size 300 x 300 x 20mm thick square in shape of approved tint, as in ramp/stair laid over 20mm thick screed bed in CM 1:4 and pigment to match the colour of tiles complete all as specified and as directed.

M&L for PCC type B-0 (1:2:4) using 12.5 mm graded stone aggregate as in coping, bond stone etc. complete all as specified and as directed. Note:- Unit rate quoted shall be deemed to be inclusive of use and waste of formwork.

M&L for moorum filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for PCC precast block 1:2:4 type B1 using 20 mm aggregate as in kerbstones fixed and jointed with CM 1:4 complete all as specified and as directed.

Labour only for removing sifcon panel from one area to another using mechanical or manual means with in a distance of 1 Kms including loading, securing and unloading all as directed by Engg in Charge.

Dismantling timber scantling 40 sqcm and over in section in unframed work, in any position complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

S&F second class soft wood boarding 40mm thick clean sawn with butt joint complete all as specified and directed.

M&L for second class soft wood in scantling in clean sawn timber framed and fixed complete all as specified and as directed.

M&L for preparing of wood and wood based material of any description and girth and applying two coats of creosote oil complete all as specified and as directed.

M&L for Plain cement concrete using RMC type B1-1:2:4 using 20 mm graded aggregate as in levelling course & finished the surface even and rough complete over existing hardened surface all as specified and directed. Note:- Due to space constraints for mixing of concrete RMC shall be used, source/manufacturer of RMC shall be approved from accepting officer before incorporating in work.

M&L for heavy duty vitrified tile of 15-20 mm thick 600x600mm size suitable for flooring in heavy traffic areas laid over screed bed of 20 mm thick cement mortar 1:4. The joints between tiles shall be filled with approved epoxy grout including dismantling of existing stone slabs/ tiles and removing of debris from site.

M&L for vitrified step tile of 10 mm thick 900x300/1200x300 mm size suitable for risers & treads on steps with heavy traffic laid over screed bed of 15 mm thick cement mortar 1:4. The joints between tiles shall be filled with approved epoxy grout including dismatling of existing stone slabs/ tiles and removing of debris from site.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed.

LAKSHMI BUILDERS (BID ID -3090132)

M/S V ASSOCIATES (BID ID -3088142)

KDR CONSTRUCTION (BID ID -3089322)