GE AF/AMB-51/2021-22 PROVISION OF WEATHER SHELTER WITH LED LIGHTS NEAR MAIN GUARD ROOM AT SITE-IV (KALPI) AND CERTAIN MINOR WORKS AT VARIOUS LOCATIONS UNDER GE (AF) AMBALA

Amount

Excavating in post holes (or similar holes) each not exceeding 0.5cum, returning, filling in, getting out in soft / loose soil and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm and removing surplus soil to a distance not exceeding 50m complete all as specified and as directed

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified and as directed

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundations, manholes, etc. or for laying cables/pipes, erecting poles, etc. not exceeding 10sqm on plan and getting out in soft / loose soil complete all as specified and as directeddisposing off complete all as specified and as directed

Returning, filling in, including, spreading, leveling, watering and well ramming in layers not exceeding 25cm deep as in any type of soil complete all as specified and as directed

Removing excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point in any type of soil including spreading in low lying area and leveling complete all as specified and as directed

M&L for spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and as directed

M&L for hard core of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface, using broken stone or boulders complete all as specified and as directed

M&L for 100mm thick plain cement concrete 1:2:4 (type B-1) using 20mm graded stone aggregate as in flooring, etc. complete all as specified and as directed

M&L for plain cement concrete 1:3:6 (type C-2) using 40mm graded stone aggregate as in foundation, filling, mass concrete, etc. complete all as specified and as directed

M&L for plain cement concrete 1:4:8 (type D-2) using 40mm graded stone aggregate as in foundation, filling, mass concrete, etc. complete all as specified and as directed

M&L for forming 12mm thick expansion joints, for 100mm thick concrete slab, filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as specified and as directed

M&L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410W (grade-E 250) quality-A complete all as specified and as directed

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar works conforming to Fe-290 grade E-165 complete all as specified and as directed

M&L for hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh, etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed at both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5cm in length, dia of neck & shank 10mm complete all as specified and as directed

M&L for mild steel round bars 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips for runners of chain link fencing, etc. complete all as specified and as directed

M&L for framed works conforming to Fe 410-W (grade E-250) quality-A as in doors or gates of angle or other section with gusset plates, rails, braces, etc. drilled for fixing of steel sheeting or other coverings, doors, channels, beams, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and as directed

Supply only chain link MS galvanised fencing, any size or type complete all as specified and as directed Note: Weight of chain link shall be ascertained by a BOO ordered by the GE

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provisioning of binding wire complete all as specified and as directed

M&L for preparing of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint (tint as approved) over a coat of red oxide zinc chrome primer complete all as specified and as directed

M&L for preparation of surfaces of any description, not exceeding 10cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint (tint as approved) over a coat of red oxide zinc chrome primer complete all as specified and as directed

S&F false ceiling with powder coated GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with 2Nos. unequal flanges of 20 & 30mm and web 27mm fixed to surrounding wall using nylon sleeves at 900mm c/c with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m in length) of 0.55mm thickness, having curled web of 50mm and flange 26mm each with lips of 10.5mm fixed to intermediate channel with connecting clips at 457mm c/c to 6mm dia GI hangers (1.2m long) adjusting level fixed to roof slabs by means of ceiling cleats made of GI flat 40x3mm, 60cm long and expansion hold fasteners 12.5mm dia 40mm long including 9 to 10mm thick ceiling boards / tiles (of approved design) of size 600x600mm for insulation and accoustic purposes, decorative type, with silver foil coating on backsides fixed with staples on snap grid with and including 4mm dia GI wire, nuts, bolts, washers, etc. complete all as specified and as directed

S&F in position aluminium-zinc colour coated high tensile alloy steel trap corrugated sheeting of 0.5 to 0.53mm thick, high rib, having 550 Mpa yeild strength BMT 0.45mm and zinc (galvanized) and aluminum combined coating of 150 gms/sqm (AZ-150) of 0.50mm TCT having top colour coat of regular modified polyester/silicon modified polyester/HDPE polyester of 18 to 20micron and back coat of 5 to7 micron epoxy primer fixes, RMR 1040 profile width 1125mm in roofing panels / sheeting / ridges complete as per manufacturer's instructions, all as specified and as directed Note: The sheet shall be fixed to MS angles with self drilling and self topping screws conforming to AS 3566 with moulded EPDM washers

S&F in position aluminium-zinc colour coated high tensile alloy steel trap plain sheeting of 0.5 to 0.53mm thick, high rib, having 550 Mpa yeild strength BMT 0.45mm and zinc (galvanized) and aluminum combined coating of 150 gms/sqm (AZ-150) of 0.50mm TCT having top colour coat of regular modified polyester/silicon modified polyester/HDPE polyester of 18 to 20micron and back coat of 5 to7 micron epoxy primer fixes, RMR 1040 profile width 1125mm in roofing panels / sheeting / ridges complete as per manufacturer's instructions, all as specified and as directed Note: The sheet shall be fixed to MS angles with self drilling and self topping screws conforming to AS 3566 with moulded EPDM washers

M&L for installing, testing and commissioning submersible pump set, comprising of squirrel cage motor+pump set multistage, coupled with each other, 3 phase, 415V 200mm dia dia suitable for AC operation with discharge capacity of 10000gallons/hour at 100m head suitable for 200mm bore suction, ISI marked, including necessary accessories required for fixing and commissioning like fixing clamps, nylon rope of suitable size for carrying the pump in bore well, cable required for connecting from panel to position of pump, connecting up, etc. complete all as specified and as directed

M&L for supplying, installing, testing and commissioning non-clog pump set of capacity 200LPM at 12m head electrically operated single phase 240V duly fixed with suction/delivery pipes, placed and fixed at any location complete all as specified and as directed

Supply, laying, jointing, connecting and testing XLPE insulated, screened, PVC sheathed cable 1100V grade, screwed PVC bedded, armoured electric power cable, heavy duty, stranded aluminium conductor laid in trenches / fixed on walls/poles, passing through pipes, etc. complete all as specified and as directed of the following sections Note: Excavation and earthwork will be measured and paid separately under respective item herein

3.5 core 120sqmm

3.5 core 95sqmm

3.5 core 25sqmm

M&L for taking out LT undergound cable of size 95/120sqmm from old existing panel to other new existing panel, and duly connecting up for connections, etc. complete all as specified and as directed

Supplying, fixing / laying PVC insulated aluminium conductor cable, 2 core 6sqmm, flat, solid aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed, 1100V grade heavy duty in service connections suspended by and including insulated hangers not more than 1.0m c/c and 4mm suspension wire complete all as specified and as directed

Supply, installation, testing & commissioning of powder coated compartmentalized LT panel, of suitable size, front and back openable, outdoor type, with louvers and air vents, symetrical with overload, short circuit and earth fault protection, having bus bar chambers with rated copper bus bar 3 phase 300A and half neutral, duly insulated with coloured PVC sleeves as per standard code, rigidly mounted on bakelite / DMC insulators (square / round with good insulation resistance), fabricated out of 3.15mm thick CRCA sheet steel, totally enclosed, dust proof, weather proof, vermin proof, double door with suitable locking arrangements and suitable for operation on 415V, 50Hz supply with gland plates, cable glands, lifting hooks, ventilating louvers, bus bars, inter connections, earthing, labeling electrical interlocking, suitable for termination of cables, mounted/fixed on and including MS angle iron stand /frame 40cm height from FFL, fabricated out of 40x40x6mm thick MS angle legs (4Nos.) duly grouted in ground in platform (as per manufacturer's instructions) painting all exposed metal surfaces with two coats of synthetic enamel paint (of approved tint) over a coat of red oxide zinc chrome primer with, accommodating and including 1No. 3 phase static energy meter of accuracy class 1.0, 3x240V, 50Hz, with backlit LCD display of rating 10 to 100A suitable for measuring kWh and connecting up complete all as specified and as directed

Supply, installation, testing & commissioning of powder coated compartmentalized LT panel, of suitable size, front and back openable, outdoor type, with louvers and air vents, symetrical with overload, short circuit and earth fault protection, having bus bar chambers with rated aluminium bus bar 1 phase 600A and half neutral, duly insulated with coloured PVC sleeves as per standard code, rigidly mounted on bakelite / DMC insulators (square / round with good insulation resistance), fabricated out of 3.15mm thick CRCA sheet steel, totally enclosed, dust proof, weather proof, vermin proof, double door with suitable locking arrangements and suitable for operation on 415V, 50Hz supply with gland plates, cable glands, lifting hooks, ventilating louvers, bus bars, inter connections, earthing, labeling electrical interlocking, suitable for termination of cables, mounted/fixed on and including MS angle iron stand /frame 40cm height from FFL, fabricated out of 50x50x6mm thick MS angle legs (4Nos.) duly grouted in ground in platform (as per manufacturer's instructions) painting all exposed metal surfaces with two coats of synthetic enamel paint (of approved tint) over a coat of red oxide zinc chrome primer with, accommodating and including the following and connecting up complete all as specified and as directed

Panel with the following: (i) 600A rated aluminium bus bar (ii) MCCB three phase adjustable type with thermal magnetic release 250A 35kA four pole - 1No. (iii) MCCB three phase adjustable type with thermal magnetic release 160A 35kA four pole - 2Nos. (iv) Digital ampere meter and voltmeter

Panel with the following: (i) 600A rated aluminium bus bar (ii) MCCB three phase adjustable type with thermal magnetic release 160A 35kA four pole - 1No. (iii) MCCB three phase adjustable type with thermal magnetic release 63A 35kA four pole - 4Nos. (iv) Digital ampere meter and voltmeter

S&F electric water heaters (geysers), stainless steel body, 50litres capacity, storage type, vertical mounting, with glass lined inner tank, energy efficient 5 star rated of approved design and colour, including all necessary clamps, grouting duly with holding bolts & nuts and all necessary connections at locations complete all as specified and as directed

Supply, fixing, connecting and testing plug top & socket with sheet metal enclosures SP including one MCB 20A, 240V,10kA complete all as specified and as directed

S&F GI tubing, medium grade, fixed to wall / ceiling including necessary fittings viz. elbow, union, nipple, tees, bends, short & diminishing pieces, connectors, back-nuts, caps, sockets, plugs, etc., fixtures, clamps, etc. and making good the disturbed surfaces in CM 1:4 complete all as specified and as directed of the following bores:

15mm bore

20mm bore

25mm bore

40mm bore

50mm bore

M&L for cutting existing steel tubing for addition / alteration / connecting of branches, etc. upto 50mm bore pipes including making good the disturbed surfaces complete all as specified and as directed

S&F PVC pipe 40mm bore fixed to wall / ceiling including necessary fittings, fixtures, clamps, etc. and making good the disturbed surfaces in CM 1:4 for drain pipes complete all as specified and as directed

S&F 15mm dia bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed

S&F 15mm dia stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed

S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed, heavy duty, including necessary cutting into existing pipe, threading, inserting new piece of GI pipe of existing size, and earthwork in any type of soil or breaking/cutting into road/interlocking tiles/cement concrete, etc. and making good the disturbed surfaces complete all as specified and as directed of the following sizes:

15mm dia

20mm dia

25mm dia

40mm dia

50mm dia

S&F 20mm dia ball brass valves, PTMT, high pressure, with epoxy coated aluminium rod and high density polythene float and flynut, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed

S&F 15mm steel wire braided PVC connections, 450mm long with brass couplings, PTMT nuts, etc. suitable for cold water feed to geysers complete all as specified and as directed

S&F 15mm steel wire braided PVC connections, 450mm long with brass couplings, PTMT nuts, etc. suitable for hot water from geysers complete all as specified and as directed

M&L for submain wring using proper colour coding with 2 runs of single core, PVC insulated, FRLS unsheathed suitable for 1100V, multistranded, copper conducter cable of size 4sqmm and 1 run of 2.5sqmm multistranded, copper conductor cable 1100V green colour for earth conductor drawn through and including PVC conduit 25mm bore, heavy duty, ISI marked fixed on wall/ceiling, etc. with all required accessories, making good the disturbed surfaces in CM 1::4 and applying two coats of distemper oil emulsion complete all as specified and as directed

M&L for submain wring using proper colour coding with 2 runs of single core, PVC insulated, FRLS unsheathed suitable for 1100V, multistranded, copper conducter cable of size 2.5sqmm and 1 run of 2.5sqmm multistranded, copper conductor cable 1100V green colour for earth conductor drawn through and including PVC conduit 25mm bore, heavy duty, ISI marked fixed on wall/ceiling, etc. with all required accessories, making good the disturbed surfaces in CM 1::4 and applying two coats of distemper oil emulsion complete all as specified and as directed

M&L for submain wring using proper colour coding with 2 runs of single core, PVC insulated, FRLS unsheathed suitable for 1100V, multistranded, copper conducter cable of size 2.5sqmm and 1 run of 1.5sqmm multistranded, copper conductor cable 1100V green colour for earth conductor drawn through and including PVC conduit 25mm bore, heavy duty, ISI marked fixed on wall/ceiling, etc. with all required accessories, making good the disturbed surfaces in CM 1::4 and applying two coats of distemper oil emulsion complete all as specified and as directed

Notes for item Nos. 58 to 60: (i) 2 runs of main cable, 1 run of earth conductors and 1 run of PVC conduit as per item shall be measured as one length (ii) Separate conduit shall be used for each sub-main wiring circuit irrespective of numbers of wire (iii) The minimum size of conduit shall be as stipulated, however higher sizes shall be used as per number of cables passing through. The Engineer-in-charge shall ensure for proper size of conduit as per requirement at site

S&F sheet metal enclosures for MCB distribution board 230V, SPN, 4 way, single door type, flushed inside wall with 200A rated bus bar and making good the disturbed surfaces complete all as specified and as directed

S&F sheet metal enclosures for MCB distribution board 230V, SPN, 4 way, single door type, flushed inside wall with 100A rated bus bar and making good the disturbed surfaces complete all as specified and as directed

S&F MCB SP, 240V, 5 to 40A, 10kA, 'C' curve, finger proof terminal, bi-connect termination, 35sqmm terminal capacity, insulated sliding shutter with large two position dolly complete all as specified and as directed

S&F MCB SP, 240V, 5 to 40A, 10kA, 'B' curve, finger proof terminal, bi-connect termination, 35sqmm terminal capacity, insulated sliding shutter with large two position dolly complete all as specified and as directed

S&F MCB SPN, 240V, 5 to 40A, 10kA, 'C' curve, finger proof terminal, bi-connect termination, 35sqmm terminal capacity, insulated sliding shutter with large two position dolly complete all as specified and as directed

S&F MCB isolator SPN, 240V, 5 to 40A, 10kA, 'B' curve, finger proof terminal, bi-connect termination, 35sqmm terminal capacity, insulated sliding shutter with large two position dolly complete all as specified and as directed

S&F MCB isolator SP, 240V, 5 to 40A, 10kA, 'B' curve, finger proof terminal, bi-connect termination, 35sqmm terminal capacity, insulated sliding shutter with large two position dolly complete all as specified and as directed

S&F MCB isolator TPN, 415V, 63A, 16kA, 'B' curve, finger proof terminal, bi-connect termination, 35sqmm terminal capacity, insulated sliding shutter with large two position dolly complete all as specified and as directed

M&L for point wiring with 1.5sqmm, single core, FRLS PVC insulated, ISI marked, unsheathed cable 1100V grade with multi-stranded copper conductor, drawn through and including non-metallic rigid PVC casing caping not less than 20mm wide and accessories flush on walls, ceiling etc., and including provision of 1.5sqmm copper wire, green colour as earth continuity conductor and connected to common earth dolly and making good to the surface to match the existing and MS sheet (1.6mm thick) sunken box or pressed steel terminal boxes with provision of 3mm thick plastic laminated sheet top cover with gang box of module suitable for mounting 6/16A switch socket boxes for one 3 pin switch socket combination outlet 6A on independent board complete all as specified and as directed

M&L for point wiring with 1.5sqmm, single core, FRLS PVC insulated, ISI marked, unsheathed cable 1100V grade with multi-stranded copper conductor, drawn through and including non-metallic rigid PVC casing caping not less than 20mm wide and accessories flush on walls, ceiling etc., and including provision of 2.5sqmm copper wire, green colour as earth continuity conductor and connected to common earth dolly and making good to the surface to match the existing and MS sheet (1.6mm thick) sunken box or pressed steel terminal boxes with provision of 3mm thick plastic laminated sheet top cover for one light/fan point controlled by one 1 way switch on independent board complete all as specified and as directed

M&L for point wiring with 1.5sqmm, single core, FRLS PVC insulated, ISI marked, unsheathed cable 1100V grade with multi-stranded copper conductor, drawn through and including non-metallic rigid PVC casing caping not less than 20mm wide and accessories flush on walls, ceiling etc., and including provision of 1.0sqmm copper wire, green colour as earth continuity conductor and connected to common earth dolly and making good to the surface to match the existing and MS sheet (1.6mm thick) sunken box or pressed steel terminal boxes with provision of 3mm thick plastic laminated sheet top cover with gang box of module suitable for one exhaust fan point controlled by one 1 way switch on independent board complete all as specified and as directed

M&L for point wiring with 2.5sqmm, single core, FRLS PVC insulated, ISI marked, unsheathed cable 1100V grade with multi-stranded copper conductor, drawn through and including non-metallic rigid PVC casing caping not less than 20mm wide and accessories flush on walls, ceiling etc., and including provision of 1.5sqmm copper wire, green colour as earth continuity conductor and connected to common earth dolly and making good to the surface to match the existing and MS sheet (1.6mm thick) sunken box or pressed steel terminal boxes with provision of 3mm thick plastic laminated sheet top cover with gang box of module suitable for mounting 6/16A switch socket boxes for one 5 pin switch socket combination outlet 15/16A multi-purpose on independent board complete all as specified and as directed

M&L for point wiring with 4sqmm, single core, FRLS PVC insulated, ISI marked, unsheathed cable 1100V grade with multi-stranded copper conductor, drawn through and including non-metallic rigid PVC casing caping not less than 20mm wide and accessories flush on walls, ceiling etc., and including provision of 2.5sqmm copper wire, green colour as earth continuity conductor and connected to common earth dolly and making good to the surface to match the existing and MS sheet (1.6mm thick) sunken box or pressed steel terminal boxes with provision of 3mm thick plastic laminated sheet top cover for one 3 pin socket outlet 15A on independent board complete all as specified and as directed

M&L for point wiring with 4sqmm, single core, FRLS PVC insulated, ISI marked, unsheathed cable 1100V grade with multi-stranded copper conductor, drawn through and including non-metallic rigid PVC casing caping not less than 20mm wide and accessories flush on walls, ceiling etc., and including provision of 2.5sqmm copper wire, green colour as earth continuity conductor and connected to common earth dolly and making good to the surface to match the existing and MS sheet (1.6mm thick) sunken box or pressed steel terminal boxes with provision of 3mm thick plastic laminated sheet top cover for one 20A metal clad socket on independent board complete all as specified and as directed

S&F switch piano flush button type, single pole, ISI marked, one way 5/6A, 240V complete all as specified and as directed

S&F switch piano flush button type, single pole, ISI marked, one way 15A, 240V complete all as specified and as directed

S&F socket outlet, 3 pin, multipurpose 5A flush type, ISI marked, 240V complete all as specified and as directed

S&F socket outlet, 2 in 1, 3 pin, multipurpose 15A flush type, ISI marked, 240V complete all as specified and as directed

S&F ceiling rose surface bakelite 65x50mm, ISI marked, with three terminals complete all as specified and as directed

M&L for installing, testing and commissioning dehumidifier, industrial type, stainless steel body, 220V 50Hz, moisture extraction capacity 250L/day and air flow @1600cum/hour with reciprocating type compressor charged with R-22 refrigerant, ISI marked, including necessary accessories required for fixing and commissioning like fixing clamps, connecting cable duly connected up, etc. complete all as specified and as directed Make: Cat No. S TDV 600 of M/s Safety Concepts or equivalent model of M/s Tripti, M/s NTC, M/s Sujay Inc.

S&F PP-R gate valves (brass insert) suitable for 20mm outer dia of pipes as per requirement of site complete all as specified and as directed

S&F and testing 3kVA voltage stabilizer for operation on single phase designed for working range 160V to 260V 50Hz in position / location complete all as specified and as directed

Supply, installation, testing & commissioning in position automatic boost/buck transformer of capacity 5kVA, for low and high voltage correction nd cutoff with time delay relay device equipped with electronic transistor suitable for correction on single phase 50Hz AC supply with voltmeter designed for input voltage 160V to 260V and output voltage 210V to 220V with and including all required accessories and connecting up complete all as specified and as directed

Supply, installation, testing & commissioning in position water cooler 180litres capacity, complete food grade stainless steel body, internal tanks made of food grade stainless steel, electric driven, singe phase, cooling capacity 150litres/hour with 02Nos. stainless steel taps, both giving cold water and including 2 tape, drain pipe, and all connecting accessories, etc. complete all as specified and as directed

Supplying, fixing, connecting and testing split type room air-conditioners of capacity 2TR, EER 3.2, 5 star rated, with cordless remote control unit, with inbuilt air ioniser and plasma filter, non-CFC, placed and fitted at location, hi-wall mounted, placing outdoor unit as as required, with all connecting accessories including making recess on walls, provision of suitable 3core flexible wire from connection to unit, copper tubing with suitable insulation and drain out pipe as required and making good the disturbed surfaces to existing finishes complete all as specified and as directed

S&F 4 core 2.5sqmm copper flexible power cable in any position / location and connecting up complete all as specified and as directed

S&F framed work, fabricated out of MS sheet, MS flat and angle iron of required sizes or shapes required at site for staging / supports of water cooler, water tanks, panels, etc. including all required cutting, notching, welding, drilling, fastening, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings and similar works conforming to Fe-290 grade E-165 and painting with one coat of synthetic enamel paint of approved colour complete all as specified and as directed complete all as specified and as directed

S&F smart fan rod (anti-suicide fan rod) mild steel, 15inch long, to ceiling fans in any locations / heights after disconnecting the fans, taking down with and including providing new rubber reel of existing / suitable size and re-fixing the fans, with suitable nuts, bolts and washers, placing of canopies and connecting up complete all as specified and as directed

S&F flame proof weather proof LED tube light fitting 1x16W, 240V, 4' long, suitable for gas / vapour group IIA & IIB and zone 1&S, IP- 65 protection calss, with all accessories pre-wired and connecting with ZHFR grade twin core twisted flexible copper conductor cable and testing on installation complete all as specified and as directed

S&F flame proof, heavy duty, metalic body with metalic blades, legs, ISI marked energy efficient BEE five star rated exhaust fan, 457mm sweep, 1440RPM, CFM 4000 with lauvers and connecting up including provision of three core flexible copper wire of size 1.5sqmm from ceiling rose to exhaust fan including making hole on wall grouting bolts nuts washers, etc. complete all as speceified and as directed

S&F energy efficient LED flood light fitting, 90W, input voltage 230V, 50Hz with ingress protection IP 65, CRI>70, PF>0.95, minimum 50000 burning hours, THD> 20, operating on over voltge range of 140V to 270V, duly housed in pressure die cast aluminium housing, including all fixing arrengment like clamps, nuts, bolts, washers, 90W LED lamp with all accessories pre-wired and connecting with twin core twisted flexible copper conductor cable with all necessary staging, etc. for fixing at any locations complete all as specified and as directed

Supplying, hoisting, fixing and connecting up rotational moulded polythylene water storage tanks (cylindrical vertical with closed top), hoisted, placed and fixed in position all as specified in SSR Part-I including connecting the overflow drain out, inlet and outlet pipes, tank nipple, elbow, bend, unions, sockets, etc. complete all as specified and as directed of the following capacities:

200litres

1000litres

M&L for cutting / boring into roads / paths / hard standing, concrete / tiled / bituminous, etc. for insertion of GI protection / passing through pipes 50mm bore, at any length at any location including making good the disturbed surfaces after laying of pipes complete all as specified and as directed

Supplying, fixing / laying steel water tubing, 50mm bore, light grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for protection of electric clables complete all as specified and as directed

M&L for pre-cast cement concrete block masonry with solid blocks in PCC 1:3:6 (type C1) using 20mm graded stone aggregates, exceeding 10cm in width and set in CM 1:6 complete all as specified and as directed

M&L for fine dry river sand cushioning by laying 8cm thick layer below the cable for making soft bed and 15cm above the cable and then punning down to its consolidated thickness of 18cm after the cable is laid all as specified in SSR Part-I complete all as specified and as directed Note: Only punned thickness of sand shall be considered for measurement purposes

Supply and laying burnt bricks of sub-class 'B' designation 75 laid in trenches for cable protection complete all as specified and as directed

Supply, installation, testing and commissioning maintenance free tripod chemical earthing system consisting of 3Nos. of solid copper earth rod of 17.2mm dia and 3m long made of high tensile low carbon steel, molecularly bonded with 99.9% electrolyitc grade copper on outer surface having 250microns (minimum thickness) with exothermically jointed copper bus bar of 150x25x3mm for long lasting and connecting each copper rod and the exothemically jointed bus bar, both CPRI tested on at leat 25kA fault current ensuring high current carrying capacity of the system and earth rod should be certified by laboratories confirming to comply with UL 467 international standards grounding and bonding equipment and each rod should be used with minimum 50kg earth enhancing compund that should be ROHS tested and have passed leaching sulpher, corrosion, resisitivity test shall be less than 0.05lhm mtr and international standard for earth enhancement compound by NABL acredited laboratory and each rod should be interconnected with 8mm dia copper clad steel conductor at the distance of 3m to make a shape of traingle with top of the bore finished with 40mm thick PCC in 1:2:4 type B-1, 75mm thick PCC in 1:4:8 type D-2 and back fill/JAM compund shall be covered with advanced polymer pit cover of 30x30mm size complete all as specified and as directed

Notes for item No. 101: (i) The earthing shall comply to IS 3043, UL 467, BS/EN50164-7 (ii) The earth resistance shall be less than 01Ohm. A guarantee for 3years of this criterion on a Rs. 100 stamp paper shall be given by the Contractor. The quoted rate shall be deemed to be inclusive of this aspect (iii) To obtain earth resistance less than 01Ohm, if a combination two or more earthings are to be inter-connected or the length of the electrode/s is/are to be increased it shall be measured and paid as one earthing only (iv) Testing of earthing shall be carried out in presence of Departmental rep and requisite test reports shall be submitted (v) Cost of all excavation & earthwork required shall be deemed to be included in the quoted rate

M&L for earthing using GI earthing with galvanised steel earth plate electode 600x600x6mm thick buried directly in ground, earth pit not less than 2.25m deep below ground level connection to and including GI strip of size 32x6mm extended to 7.5m as earth lead by means of GI bolts, nuts, etc. with provision of charcoal and salt all as per electrical plate No. 3 of SSR Part-I including water arrangement with GI pipe 20mm dia (medium grade), earth lead protection pipe 50mm medium grade with bends, elbow, etc. from earth plate to test point, excavation and earthwork in any type of soil, returning, filling, ramming and removing of soil to distance not exceeding 50m, make good to match with existing surface making PCC pit (earth chamber) having internal size 300x300x300mm and outer size 600x 600x600mm with RCC reinforced cover 50mm thick and testing on completion including making test points on wall as per SSR specifications complete all as specified and as directed

M&L for earthing using GI earthing wire with galvanised steel earth plate electode 600x600x6mm thick buried directly in ground, earth pit not less than 2.25m deep below ground level connection to and including GI wire of size 4sqmm extended to 7.5m as earth lead by means of GI bolts, nuts, etc. with provision of charcoal and salt all as per electrical plate No. 3 of SSR Part-I including water arrangement with GI pipe 20mm dia (medium grade), earth lead protection pipe 50mm medium grade with bends, elbow, etc. from earth plate to test point, excavation and earthwork in any type of soil, returning, filling, ramming and removing of soil to distance not exceeding 50m, make good to match with existing surface making PCC pit (earth chamber) having internal size 300x300x300mm and outer size 600x 600x600mm with RCC reinforced cover 50mm thick and testing on completion including making test points on wall as per SSR specification complete all as specified and as directed

Notes for serial item Nos. 103 & 104: (i) The cost of GI earth continuity strip with GI pipe 20mm medium grade upto 7.5m is deemed to be included (ii) The earth chamber to be constructed 0.5m from edge of earth pit with necessary watering arrangement. The cost for the same is deemed to be included in above item (iii) Earthing shall produce desired earth resistance values as directed by the Engineer-in-charge

s.v.builders

M/S Sonu Traders