Loading
Loading…
Loading…
Tender Value
₹13.6 Cr
EMD Value
₹27.2 L
Closing Date
17 Jun 2026, 3:00 pmClosed
Yes (up to 3 members)
No
Two Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
90 days
Expenditure
Capital (Works)
Above/Below/Par
TECHNICAL
15 conditions · 4 needing a document upload
"Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or ""V"" whichever is less crores; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIII, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
"(a)The tenderer must have successfully completed/substentially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of the tender. (b) (i) In case of composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed/substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or Two similar works , each costing not less than the amount equal to 40% of advertised value of each component of tender, ora One similar work, each costing not less than the amount equal to 60% of advertised value of each component of tender. Note: Separate completed works of minimum required values for each component can also be considered for fulfillment of technical eligibility criteria. (b) (ii) In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. Any work or set of works shall be considered to be a separate component, only when cost of the component is more than Rs. 2 crore each. The tenderer shall submit the completion certificate as per proforma given in annexure-IV-A or IV-B or IV-C as applicable or in the format containing all information as required as per the Annex. IV-A or IV-B or IV-C. Note :- Criteria for the completed work/Substantially completed has been given in the General instructions in the tender document. "
lectrical contract license: - The contractor should have valid electrical contractor license issued by government and submit along with tender document. If valid electrical contractor license is not submitted alongwith tender document then offer will be summarily rejected. The OEM or his authorized dealer will be exempted from license (Authority:-NWR/HQ letter no. EL/50/STD/Vol. II dated 24.09.2018
Any electrical work related to LT/HT installation.
64 conditions · 9 needing a document upload
Mandatory in case Bid Security amount is prescribed in clause no. 5.1.2 of General Instructions of Standard Tender Document/Special condition of Contract (Version 11.4) for IREPS - The Bid Security shall be deposited in cash through e-payment gateway or submitted as Bank Guarantee bond from a scheduled commercial bank of India or as mentioned in tender documents. The Bank Guarantee bond shall be as per Annexure- XXXII and shall be valid for a period of 90 days beyond the bid validity period.
In case the tenderer is (i) Any firm recognized by Department of Industrial Policy and Promotion (DIPP) as 'Startups' - shall be exempted from payment of Bid Security deposit and shall submit certified copy of the registration/ Valid document issued by DIPP (mandatory if applicable).
In case the tenderer is (iii) Labour Cooperative Societies - shall deposit only 50% of the Earnest Money / Bid Security Deposit and shall submit certified copy of the registration/ Valid document issued by the relevant Ministry/ Labour commission (mandatory if applicable).
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The Minimum Increment as mentioed in the Clause no. 26.1 (b), Annexure C, Para 2 of the "GENERAL INSTRUCTIONS" of Tender Document will be as per railway board guidelines or as approved by Tender accepting authority . (Applicable to the works and service tenders of value more than Rs.50 crore.)
I/We have read the various conditions to tender attached here to and agree to abide by the said conditions. I/We also agree to keep this tender open for acceptance for a period as mentioned in NIT header from the date fixed for opening the same and in default thereof, I/We will be liable for forfeiture of my/our "Bid security". I/We offer to do the work for North Western Railway, at the rates quoted in the attached schedule and hereby bind myself/ourselves to complete the work in all respects within time period as mentioned in the NIT Header from the date of issue of letter of acceptance of the tender.
I/We also hereby agree to abide by the General Conditions of Contract-2022 corrected up- to- date and to carry out the work according to the Special Conditions of Contract and Indian Railways Unified Standard Specifications (Materials and Works) 2021 as corrected up-to-date, Unified Standard Schedule of Rates of North-Western Railway - 2021 as corrected up-to-date & CPWD DSR-2021 and Specification 2019 (for the present contract)
Electrical work of Redevelopment of Pali-Marwar Railway Station of North Western Railway.
EL-C-JU-PMY-Red-26-27-T01
EL-C-JU-PMY-Red-26-27-T01
Open
Works - General
18 Months
Jodhpur, Rajasthan
₹0
₹27.2 L
20 May 2026
20 May 2026
3 Jun 2026
483 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 13,60,32,912 | ||
| — | 1690.00 | — | — | ||
| Recessed/Surface conduit wiring system-Supply of material and wiring of LP/TP/FP/Exhaust fan/ Bell point with single core multistrend copper conductor size 1.5 Sq.mm in PVC conduit pipe with 5/6 Amp modular type switch/ceiling rose/batten holder etc. As per specification | — | — | — | 5,98,260 | |
| — | 1067.00 | — | — | ||
| Supply and fixing 5/6A plug, modular 5-pin 230V including modular switch and with modular board and wiring with 2.5sqmm PVC CU cable as per spec. | — | — | — | 2,39,008 | |
| — | 949.00 | — | — | ||
| Supply and fixing 15/16A plug, modular 5-pin 230V including modular switch and with modular board and wiring with 04.0sqmm PVC CU cable as per spec. | — | — | — | 2,39,148 | |
| — | 350.00 | — | — | ||
| Supply and fixing 2 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS /PVC as per site engineer | — | — | — | 37,100 | |
| — | 300.00 | — | — | ||
| Supply and fixing 6 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS /PVC as per site engineer | — | — | — | 57,300 | |
| — | 250.00 | — | — | ||
| Supply and fixing 8 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS /PVC as per site engineer | — | — | — | 64,750 | |
| — | 100.00 | — | — | ||
| Supply and fixing 12 module modular switch board plate for fixing of modular switches -plug with sheet metal box of good quality concealed fixing of MS /PVC as per site engineer | — | — | — | 29,500 | |
| — | 472.00 | — | — | ||
| Supply and fixing ceiling of fan regulator electronic type 5-step as per spec | — | — | — | 1,45,376 | |
| — | 5000.00 | — | — | ||
| Supply, laying, connection and commission of sub-main 2x2.5 Sqmm with PVC insulated single core copper conductor cable and same size PVC insulated copper conductor for earthing wire in 19/20 mm ISI PVC conduit in recessed/ on surface as per site requirement etc. of various size cable as below. As per specification. | — | — | — | 2,90,000 | |
| — | 5000.00 | — | — | ||
| Supply, laying, connection and commission of sub-main 2x4 Sqmm with PVC insulated single core copper conductor cable and same size PVC insulated copper conductor for earthing wire in 19/20 mm ISI PVC conduit in recessed/ on surface as per site requirement etc. of various size cable as below. As per specification. | — | — | — | 5,05,000 | |
| — | 1000.00 | — | — | ||
| Supply, laying, connection and commission of sub-main 2x6 Sqmm with PVC insulated single core copper conductor cable and same size PVC insulated copper conductor for earthing wire in 19/20 mm ISI PVC conduit in recessed/ on surface as per site requirement etc. of various size cable as below. As per specification. | — | — | — | 1,11,000 | |
| — | 1000.00 | — | — | ||
| Supply, laying, connection and commission of sub-main 2x10 Sqmm with PVC insulated single core copper conductor cable and same size PVC insulated copper conductor for earthing wire in 19/20 mm ISI PVC conduit in recessed/ on surface as per site requirement etc. of various size cable as below. As per specification. | — | — | — | 2,52,000 | |
| — | 500.00 | — | — | ||
| Supply of material & wiring of sub-main with 2x6 sq mm PVC insulated multi-strand ( 84 /.30mm ) copper conductor cable in existing laid ( surface / recessed) PVC conduit pipe and continuous running of PVC insulated copper earth wire of 1Sq.mm. as per specifications attached as required. | — | — | — | 64,500 | |
| — | 4072.00 | — | — | ||
| Supply of material & wiring of sub-main with 2x4 sq mm PVC insulated multi-strand ( 56 /0.3mm ) cooper conductor cable in existing laid ( surface / recessed) PVC conduit pipe and continuous running of PVC insulated copper earth wire of 1Sq.mm. as per specifications attached as required | — | — | — | 3,70,552 | |
| — | 4570.00 | — | — | ||
| Supply of material & wiring of sub-main with 2x2.5 sq mm PVC insulated ( 36 /0.3 mm ) multi-strand copper conductor cable in existing laid ( surface / recessed) PVC conduit pipe and continuous running of PVC insulated copper earth wire of 1Sq.mm. as per specifications attached as required | — | — | — | 3,29,040 | |
| — | 1705.00 | — | — | ||
| Supply of material & wiring of light and fan points with PVC insulated 1.5 sq mm multi-strand ( 22/.3 mm )copper conductor cable in existing laid (surface / recessed ) PVC conduit pipe and continuous running of PVC insulated copper earth wire of 1 Sq.mm. as per specifications attached as required with supply and fixing of 5 Amp. rating piano type switch, bakelite angular/ button holder, ceiling rose, junction box and round block etc. as required | — | — | — | 5,93,340 | |
| — | 14.00 | — | — | ||
| Supply, fixing, testing and commissioning of RCBO 63A, Four pole, 30mA with Earth leakage, overload and short circuit protection as per specification. | — | — | — | 54,362 | |
| — | 14.00 | — | — | ||
| Supply, fixing, testing and commissioning of Distribution Board double door, 3-phase and neutral with incoming 63A 4-pole MCB and outgoing 12Nos. MCB 6-32A single pole as per specification | — | — | — | 83,160 | |
| — | 32.00 | — | — | ||
| Supply, fixing, testing and commissioning of RCBO 25A, Double pole, 30mA with Earth leakage, overload and short circuit protection as per specification. | — | — | — | 83,968 | |
| — | 32.00 | — | — | ||
| Supply, fixing, testing and connecting of Distribution Board with incoming 32A, single phase, DP MCB and outgoing 8Nos. single pole MCB 6-16A as per specification. | — | — | — | 99,360 | |
| — | 80.00 | — | — | ||
| Supply and fixing metal clad plug socket 20A single phase with 32A MCB including fixing and sheet metal enclosure box with one 20A plug top (Ray roll type) to be supplied with board. | — | — | — | 68,160 | |
| — | 120.00 | — | — | ||
| Supply, fixing, testing and commissioning of TPN DB 8-waywith provision of incoming MCCB of 125A,IP 43/IK09, double door at suitable locations. | — | — | — | 19,10,040 | |
| — | 2160.00 | — | — | ||
| Supply, Fixing of MCB to be provided in the MCBDB given above including supply of material as required & as per specifications attached-MCB(SP-) 6-32 A | — | — | — | 5,44,320 | |
| — | 402.00 | — | — | ||
| Supply, Fixing of RCCB to be provided in the MCBDB given above including supply of material as required & as per specifications attached-RCCB -25 A/30mA | — | — | — | 10,68,114 | |
| — | 120.00 | — | — | ||
| Supply, Fixing of MCB TPN to be provided in the MCBDB including supply of material as required &as per specifications attached-MCB(TPN)-63A | — | — | — | 2,64,840 | |
| — | 472.00 | — | — | ||
| Installation /shifting testing and connection of ceiling fans (Fans will be supplied by Railway). As per specification. | — | — | — | 58,056 | |
| — | 184.00 | — | — | ||
| Supply, fixing and commissioning of street light fitting accessories i.e. GI pipe of suitable boar/size as per fitting, clamps, nuts, bolts, cable/wire etc. As per specification. | — | — | — | 29,440 | |
| — | 198.00 | — | — | ||
| Fixing, testing & commissioning of LED street light complete (Fitting supplied by Rly. & transported by Contractor). As per Specification. | — | — | — | 18,612 | |
| — | 1555.00 | — | — | ||
| Fixing, testing & commissioning of LED tube light fitting as per spec. (Complete fitting will be supplied by Rly. & transported by the contractor). As per Specification. | — | — | — | 1,16,625 | |
| — | 12.00 | — | — | ||
| Transportation, commissioning and Installation of water cooler 150 ltrs. Water cooler will be supplied by Rly. | — | — | — | 80,556 | |
| — | 120.00 | — | — | ||
| Supply and fixing of G.I. pipe 50mm for cable laying with pole/wall/under road/floor etc. | — | — | — | 31,080 | |
| — | 6320.00 | — | — | ||
| Supply and laying of HDPE pipe conforming to IS 4984:1995, 50 mm dia wall thickness 3 mm under the road/PF/ in ground or as per site requirement. As per specification. | — | — | — | 6,82,560 | |
| — | 1720.00 | — | — | ||
| Supply and laying of HDPE pipe conforming to IS 4984:1995, 75/80mm dia wall thickness 3 mm PN-4 under the road/air. The work involves laying of HDPE pipe. As per specification. | — | — | — | 2,09,840 | |
| — | 3625.00 | — | — | ||
| Supply and laying of HDPE pipe, dia 160mm under road/ground/ floor/railway track or as per site requirement already excavated trench. As per specification. | — | — | — | 15,95,000 | |
| — | 7000.00 | — | — | ||
| Digging and filling of trench size 0.4 x 0.8 mtr as per spec. ( trench work may be on kuchha/pucca land and all type of soil as per site requirement and without protective layer of brick) | — | — | — | 3,22,000 | |
| — | 5000.00 | — | — | ||
| Excavation & refilling of 0.5 m width, 1.2 m Deep trench in all kind of soil for laying of HDPE/ SPUN Pipe for underground cable crossing. As per specification. | — | — | — | 6,50,000 | |
| — | 18500.00 | — | — | ||
| Laying, testing & commissioning of LT cable in Air/laid concrete pipe /in ground in trench across crossing pole with transportation from main depot to required site. Note: - Cable will be supplied by Railways. | — | — | — | 4,07,000 | |
| — | 2000.00 | — | — | ||
| Laying, testing & commissioning of 11 KV /33 KV XLPE cable in air/ ground/ in trench/spun pipe, with transportation from main depot to required site. Note: - Cable will be supplied by Railways. | — | — | — | 1,66,000 | |
| — | 2500.00 | — | — | ||
| Drilling of horizontal bore below Rly track by pushing method for laying of HDPE/SPUN/DWC pipe of various sizes up to 450 mm dia. As per specification. | — | — | — | 66,87,500 | |
| — | 12.00 | — | — | ||
| Supply, installation, testing & commissioning of VTPN type metal double door type 8 way DB with having 01 No. 250 Amp., 4 pole MCCB, 36 KA as incomer & 8 Nos. TP MCB, 10 KA 'C' curves, 40-63 Amp. Cap. as outgoing having suitable IP-54, IK-09 protection. | — | — | — | 6,18,756 | |
| — | 12.00 | — | — | ||
| Supply, fixing, testing and commissioning of VTPN DB 4 way having incoming 01 No. 125 Amp 4 Pole MCCB 36KA and outgoing 04 Nos. TP MCB 40/63 Amp 'C' Curve 10KA as required make from reference list. As per specification. | — | — | — | 2,37,672 | |
| — | 10.00 | — | — | ||
| Supply, installation, testing & commissioning of 04 pole MCCB, 250 AMP, 36 KA with double door encloser for outdoor purpose as par specification. | — | — | — | 1,43,090 | |
| — | 10.00 | — | — | ||
| Supply, installation, testing & commissioning of 04 pole MCCB, 125 AMP, 36 KA with double door encloser for outdoor purpose as per specification. | — | — | — | 82,910 | |
| — | 167.00 | — | — | ||
| Supply, fabrication, erection, testing and commissioning of G.I. octagonal pole 5 meters long single/double arm suitable for street light fixture including digging of pit, making foundation and muffing with cement, concrete concrete 1: 3: 6. As per Specification. | — | — | — | 17,20,267 | |
| — | 17.00 | — | — | ||
| Supply, fabrication, erection, testing and commissioning of G.I. octagonal pole 7 meters long single/double arm suitable for street light fixture including digging of pit, making foundation and muffing with cement, concrete concrete 1: 3: 6. As per Specification. | — | — | — | 1,49,753 | |
| — | 100.00 | — | — | ||
| Supply and providing of cable marker - for underground cable (Other than PLTC) The cable marker shall be made of MS sheet 1.5 mm thick size 150 x 200 mm welded with 12 mm dia MS rod 01.50 Mtrs long. The lower end of rod should be turned in hooks shape and attached with the cable at the laying | — | — | — | 16,600 | |
| — | 65.00 | — | — | ||
| Supply and Providing GI Pipe Earthing of 3 meter length. As per specification. | — | — | — | 75,205 | |
| — | 90.00 | — | — | ||
| Supply & providing copper plate earthing 4 meter deep, copper plate size 600x600x3 mm as per spec. | — | — | — | 6,46,470 | |
| — | 500.00 | — | — | ||
| Supply and fixing of Copper Earth Flat strip size 25x3mm as per spec. | — | — | — | 1,75,500 | |
| — | 1700.00 | — | — | ||
| Supply fixing and commissioning of Single Sided LED Sign board with symbol. As per specification. | — | — | — | 40,42,600 | |
| — | 1600.00 | — | — | ||
| Supply fixing and commissioning of Double Sided LED Signage board with symbol. As per specification. | — | — | — | 44,06,400 | |
| — | 20.00 | — | — | ||
| Supply, installation, testing and commissioning of call bell 220/230V as per specification. | — | — | — | 4,600 | |
| — | 4.00 | — | — | ||
| Supply, fixing, testing and commissioning of single stage Mono-block open well submersible pump set with control panel rating 2HP/1.5KW, Head range (M) :26 meters and above, size (MM) suction X delivery 50X40, Discharge (LPM):180 or above at 26 meter head suitable for single phase 50Hz AC supply make as per reference list. | — | — | — | 61,088 | |
| — | 4.00 | — | — | ||
| Supply of submersible energy efficient Pumps (3 star or above) 10HP, 20 STAGES, 3- PHASE, 415V AC complete with accessories at sight as per specification. | — | — | — | 2,83,416 | |
| — | 4.00 | — | — | ||
| Installation /lowering of submersible Pump set with G.I. pipe, nut, bolt, washer & rubber packing and copper cable As per specification. | — | — | — | 20,332 | |
| — | 1200.00 | — | — | ||
| Supply of copper flat cable size 3x6 sq mm as per specification. | — | — | — | 1,40,400 | |
| — | 4.00 | — | — | ||
| Supply and fixing pipe fittings bends, sockets, flanges, delivery valve and non-return valve and supporting clamps (2set) As per specification | — | — | — | 22,664 | |
| — | 4.00 | — | — | ||
| Supply and installation of automatic control panel with star delta starter for 10 HP three-phase pump (Monopole/Submersible) including connections and providing cable from main board to control panel and connection for WLG in open bore well as per detailed specifications. | — | — | — | 80,436 | |
| — | 800.00 | — | — | ||
| Supply of G.I. pipe 50 mm dia 'B' class for delivery. | — | — | — | 2,78,400 | |
| — | 4.00 | — | — | ||
| Supply, erection, testing and commissioning of 16 M high mast shaft totally hot dip galvanized and suitable for wind velocity as per IS 875 part-3. The mast shaft shall be in two finished section it shall also include all accessories for 16M high mast. | — | — | — | 9,21,812 | |
| — | 4.00 | — | — | ||
| Design and casting of suitable foundation with M-20 concrete for the 16mtr high mast having the safe soil bearing capacity at site as 10T/sqmtr at 2 meter depth including supply of foundation bolts manufactured from special steel along with nuts, washers and anchor plates and templates and as per specification enclosed. | — | — | — | 89,620 | |
| — | 40.00 | — | — | ||
| Supply and fixing of 160W or above LED Floodlight comprising Die cast aluminium housing with toughened glass complete with Electronic driver, Luminaries has the System lumen efficacy of 100lumen/Watt as per specification. | — | — | — | 8,58,240 | |
| — | 4.00 | — | — | ||
| Supply, installation, testing, commissioning of LED Aviation light luminaries as per specification. | — | — | — | 30,124 | |
| — | 4.00 | — | — | ||
| Supply, installation, testing and commissioning of control panel housing suitable timer control circuit for automatic ON & OFF of the 25/16 mtr. Mast lights at a pre-set time and as per specification. | — | — | — | 47,512 | |
| — | 10.00 | — | — | ||
| Supply/preparing of drawing in Auto CAD (Original+2 copies) Jat Mat paper of 85/90 GSM showing over all electrical installation of Railway station. As per specification. | — | — | — | 35,100 | |
| — | 50.00 | — | — | ||
| Supply installation Testing & Commissioning of rechargeable batten type Emergency light, 60 LEDs 4W or higher with one hour minimum backup as per specification & make as per reference list. | — | — | — | 1,41,750 | |
| — | 20.00 | — | — | ||
| Supply, install, test and commission of LED Lightfitting 4W batten, 330mm (Mirror light). As per specification. | — | — | — | 7,460 | |
| — | 40.00 | — | — | ||
| SITC of industrial high bay type LED light fitting 45 W | — | — | — | 1,68,440 | |
| — | 105.00 | — | — | ||
| SITC of LED step/ foot light | — | — | — | 3,95,325 | |
| — | 20.00 | — | — | ||
| SITC of LT heat shrinkable straight through joint (25-185sqmm cable). | — | — | — | 46,920 | |
| — | 674.00 | — | — | ||
| SITC of Recess mounting LED 18W 1'x1' luminaires as per specification & makes as per reference list. | — | — | — | 25,32,218 | |
| — | 148.00 | — | — | ||
| Supply and fixing of Recess mounted 36W (2feetx2feet) LED Luminaire comprising CRCA sheet steel housing with white powder coating complete with Electronic Driver and with small optical window added with high Translucent frosted diffuser. Having System wattage of 36W and System lumen efficacy of 100 Lumen/Watt complete with Electronic Driver. Operating voltage range 140 to 270 volt, THD<10%, Power factor>0.95, surge protection 2.5 KV and CRI>80, as per specification. | — | — | — | 9,34,620 | |
| — | 193.00 | — | — | ||
| Supply and fixing of recess mounting LED down lighters 9W white lamp type pressure die-cast aluminium housing with white front frame with opal translucent cover. High power LEDs mounted as per specification. | — | — | — | 11,44,104 | |
| — | 142.00 | — | — | ||
| Supplying, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s), minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, topdischarge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condenser fan shall be capable to operate at different speed with respect to load.The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 °C. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building) For Cooling or Heating or Both14 HP to 22 HP (14HP*1 Nos +18Hp*1 Nos+ 20Hp*4) (10HP * 3 Nos = 30 HP) | — | — | — | 34,83,686 | |
| — | 41.00 | — | — | ||
| Supplying, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and comfort washable synthetic media pre filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 0C DB and 19 0C WB temperature. (Make will be same as of Outdoor) a. 1.5 TR cassette type indoor unit | — | — | — | 13,26,678 | |
| — | 17.00 | — | — | ||
| b. 2.3 TR cassette type indoor unit | — | — | — | 5,90,971 | |
| — | 7.00 | — | — | ||
| 3.2 TR cassette type indoor unit | — | — | — | 2,64,208 | |
| — | 3.00 | — | — | ||
| 4.0 TR cassette type indoor unit | — | — | — | 1,13,811 | |
| — | 11.00 | — | — | ||
| Supply of Air cooled VRF Hi-wall type indoor unit 1.5/2.0 TR as per specification. | — | — | — | 3,26,700 | |
| — | 11.00 | — | — | ||
| Fixing and commissioning of Split AC 1.5/2.0 Ton inclusive first charging of refrigerant if required. | — | — | — | 13,101 | |
| — | 75.00 | — | — | ||
| SITC of copper distribution joint kit as per specification. | — | — | — | 4,10,550 | |
| — | 600.00 | — | — | ||
| SITC of control cabling: Supply & installation of control and transmission wiring between indoor and outdoor unit as per specification. | — | — | — | 93,600 | |
| — | 970.00 | — | — | ||
| SITC of Refrigerant piping: supply & installation of copper refrigerant piping of required sizes with nitrile insulation as per specification. | — | — | — | 13,08,530 | |
| — | 125.00 | — | — | ||
| Drain Piping: Supply, installation, testing and commissioning of rigid PVC piping complete with fittings, supports as per specifications and duly insulated with 6mm thick close cell nitrile rubber insulation as per specification. a. 32 mm dia | — | — | — | 28,125 | |
| — | 360.00 | — | — | ||
| 25 mm dia | — | — | — | 70,200 | |
| — | 2.00 | — | — | ||
| Supply & gas charging of refrigerant R-410a as per OEM design parameters (each cylinder gas 45 Kg) & testing as per specification. | — | — | — | 68,346 | |
| — | 2.00 | — | — | ||
| SUPPLY AIR DIFFUSERS- Supplying, Fixing, installation, testing and commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specifications complete etc. as required. | — | — | — | 38,940 | |
| — | 400.00 | — | — | ||
| NITRILE RUBBER- Supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required(19mm) | — | — | — | 3,20,016 | |
| — | 250.00 | — | — | ||
| Ducting- Supplying, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, bends, transitions, reducers, end caps, collars etc as required complete in all respect in confirmation with IS : 655 and approved drawings and specifications of following sheet thickness complete as required. a. Thickness 0.63 mm sheet | — | — | — | 3,80,550 | |
| — | 120.00 | — | — | ||
| Thickness 0.80 mm sheet | — | — | — | 2,06,736 | |
| — | 2.00 | — | — | ||
| Centralised Remote Controller- Supply, Installing, testing and commissioning of Central Remote system Controller (Touch manager type) with LCD display server for entire circuits with relay interface & necessary hardware/software. The scope should also inclusive of necessary control/communication cabling With PVC conduit from VRF/VRV ODU to Central Remote system Controller. | — | — | — | 1,04,312 | |
| — | 5.00 | — | — | ||
| Inline Ducted Fans -Supply, installation, testing and commissioning of Inline type duct mounted fans. Toilets fresh air Exhaust air. (i) Exhaust Air Fan (a) 500 CFM 20mm Static | — | — | — | 69,325 | |
| — | 2.00 | — | — | ||
| 400 CFM 20mm Static | — | — | — | 27,730 | |
| — | 1.00 | — | — | ||
| 1505 CFM 20mm Static | — | — | — | 13,865 | |
| — | 1.00 | — | — | ||
| 600 CFM 20mm Static | — | — | — | 13,865 | |
| — | 1.00 | — | — | ||
| 750 CFM 20mm Static | — | — | — | 13,865 | |
| — | 4.00 | — | — | ||
| 120 CFM 20mm Static | — | — | — | 40,120 | |
| — | 1.00 | — | — | ||
| 1000 CFM 20mm Static | — | — | — | 13,865 | |
| — | 1.00 | — | — | ||
| 350 CFM 20mm Static | — | — | — | 13,865 | |
| — | 1.00 | — | — | ||
| 300 CFM 20mm Static | — | — | — | 13,865 | |
| — | 1.00 | — | — | ||
| (ii) Fresh Air Fan: (a)650 CFM 20mm Static | — | — | — | 19,470 | |
| — | 1.00 | — | — | ||
| (ii) Fresh Air Fan (b)400 CFM 20mm Static | — | — | — | 14,750 | |
| — | 3.00 | — | — | ||
| (ii) Fresh Air Fan (c) 450 CFM 20mm Static | — | — | — | 53,985 | |
| — | 4.00 | — | — | ||
| (ii)Fresh Air Fan (d)100 CFM 20mm Static | — | — | — | 40,120 | |
| — | 1.00 | — | — | ||
| (ii)Fresh Air Fan (e)850 CFM 20mm Static | — | — | — | 19,470 | |
| — | 2.00 | — | — | ||
| (ii)Fresh Air Fan (f)350 CFM 20mm Static | — | — | — | 29,500 | |
| — | 1.00 | — | — | ||
| (ii)Fresh Air Fan (g)425CFM 20mm Static | — | — | — | 14,750 | |
| — | 1.00 | — | — | ||
| (ii)Fresh Air Fan (h)1280 CFM 20mm Static | — | — | — | 32,966.84 | |
| — | 1.00 | — | — | ||
| (ii)Fresh Air Fan (i)500 CFM 20mm Static | — | — | — | 18,570.84 | |
| — | 1.00 | — | — | ||
| (ii)Fresh Air Fan (j)1200 CFM 20mm Static | — | — | — | 33,110.8 | |
| — | 80.00 | — | — | ||
| Louvers- Supply and installation for Opposed Blades Powder Coated Aluminium Louvers with Heavy grade alumnium Frame with 50 MM Flanges, 100 MM Depth fixed horizontally at the angle of 45 Degrees and the pitch will be 145MM. Should be supplied with Bird Screen madeup of SS Screen. | — | — | — | 8,96,800 | |
| — | 25.00 | — | — | ||
| Fresh Air Filters -Supply and fixing of fresh air filter efficiency 90% down to 10 micron(EU-04). | — | — | — | 2,21,250 | |
| — | 45.00 | — | — | ||
| Door Transfer Grill-Supply, Installation a n d Testing o f extruded aluminium powder coated air transfer grilles to be provided at the doors on both sides. 450mmx150mm | — | — | — | 50,445 | |
| — | 35.00 | — | — | ||
| Linear Grill-Supply, Installation, Testing and Balancing of one way blow linear supply cum return air grilles complete with removable inner core as per approved shop drawing and specifications. The grilles shall be of approved colour & shade. Powder coated aluminium grille of extruded sections with integral flanges on both sides & ends as required. 150mm High Continous Grill | — | — | — | 3,92,350 | |
| — | 9.00 | — | — | ||
| Outdoor Stand Pads With Adjustable Legs-Supply and placement of company made outdoor Stand With adjustable height and made up of Aluminium / GI Frame Section with vibration isolator pads | — | — | — | 76,464 | |
| — | 1.00 | — | — | ||
| Air Washer-Supply, installation, testing & commissioning of Air Washer Unit, of following capacity, complete with:• Double-skin powder-coated casing • Centrifugal fan with TEFC motor • Cellulose cooling pads & water distribution system • Pre-filter section • Stainless steel sump with pump & drain arrangement • Electrical controls & vibration isolators • Access doors for maintenance a. 4140 CFM | — | — | — | 1,88,800 | |
| — | 1.00 | — | — | ||
| b. 11800 CFM | — | — | — | 5,34,540 | |
| — | 20.00 | — | — | ||
| Rubber mat (ISI marked) non-stick type suitable for 11 kv AC supply of size 2000x1000x25mm as per specification. | — | — | — | 18,780 | |
| — | 2.00 | — | — | ||
| Supply, Fabrication,Installation &Commissioning of 11 KV HT VCB panel ( 1 Incoming& 3 Out going )Indooor type as per specification | — | — | — | 22,65,600 | |
| — | 2.00 | — | — | ||
| Supply and testing of set of standard equipments/ instruments required for maintenance of CSS. (As per specification) | — | — | — | 1,83,224 | |
| — | 2.00 | — | — | ||
| Design, Manufacture, Supply, installation, testing & commisioning of 11/0.433KV CSS- 500 KVA (As per Specification) | — | — | — | 86,44,680 | |
| — | 2.00 | — | — | ||
| Design, Manufacture, Supply, installation, testing & commisioning of 11/0.433KV CSS- 630 KVA (As per Specification) | — | — | — | 91,54,440 | |
| — | 1.00 | — | — | ||
| Supply, Fabrication,Installation &Commissioning of MAIN LT Panel-2 (North side building) as per specification | — | — | — | 41,21,858 | |
| — | 1.00 | — | — | ||
| Supply, Fabrication,Installation &Commissioning of MAIN LT Panel-2 (North side building) as per specification | — | — | — | 26,25,500 | |
| — | 2.00 | — | — | ||
| Feeder Pillars & Panels :Design, manufacture, supply,including supervision during installation, testing and commissioning of Medium Voltage Double door, LT feeder pillars fabricated with minimum 2mm thick CRCA sheet, Conform to IS Specification, with IP-55 enclosure protection, as per IS-2137(Revised), floor mounting free standing outdoor type Feeder (Distribution) Pillar,provided with hinged detachable and lockable outer opening doors with the following incoming/outgong MCCB/MCBs mounted therein including making connections/ interconnections, earthing, painting etc. as required. All the feeder pillars shall have canopy arrangement on the top with double door & 250/300mm suitable supporting legs cover with removable sheets.The Feeder Pillar shall be Form - III (B).All MCCB to be with Thermal Magnetic Release for overcurrent and short circuit protection. All CT to be cast Resin.. All Panels shall be complete with all interconnections, busbars etc. complete as per design to be approved by the Architects. (a)BUILDING LIGHTING PANEL (SOUTH & NORTH SIDE) INCOMER: 1 no. 200 amps 4 pole automatic transfer switch (ATS) complete in all respect .1 no. 200 amps 35 kA 690 volt FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 200 A/5 A Class 1 accuracy and 15 VA burden. -- 1 Set ON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 250 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity. OUTGOING:2 no. 125 amps 4P MCCB with thermal over load and magnetic short circuit release with as required.5 no. 63 amps 4P MCB with thermal over load and magnetic short circuit release with complete as required.2 nos. 40 amp 4P 10 kA MCB with thermal over load and magnetic short circuit release compete as required. | — | — | — | 6,33,896 | |
| — | 2.00 | — | — | ||
| BUILDING POWER PANEL (NORTH & SOUTH SIDE) INCOMER:1 no. 250 amps 35 kA 690 volt FP MCCB with Microprocessor based release with protection functions-overcurrent 40%- 100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 200 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lamp BUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 300 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:3 no. 100 amps 4P MCCB with thermal over load and magnetic short circuit release with as required.12 nos. 63 amp 4P 10 kA MCB with thermal over load and magnetic short circuit release compete as required. | — | — | — | 4,04,976 | |
| — | 1.00 | — | — | ||
| VRV AC O/D PANEL (SOUTH SIDE), OUTDOOR TYPE:INCOMER:1 no. 400 amps 35 kA FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 200 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 500 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:12 no. 63 amps 4P MCB with thermal over load and magnetic short circuit release with complete as required | — | — | — | 1,64,256 | |
| — | 2.00 | — | — | ||
| COMMON SERVICES (SOUTH SIDE & NORTH SIDE):INCOMER:1 no. 160 amps 25 kA FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 160 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 200 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts.The neutral busbar is to be of 50% capacity.OUTGOING:3 no. 63 amps TPN MCCB with thermal over load and magnetic short circuit release with complete as required.5 no. 40 amps TPN MCB with thermal over load and magnetic short circuit release with complete as required. | — | — | — | 2,85,560 | |
| — | 2.00 | — | — | ||
| LIFT/ESCALATOR PANEL (SOUTH & NORTH SIDE)INCOMER:1 no. 125 amps 25 kA FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 125 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 160 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:2 no. 63 amps TPN MCB with thermal over load and magnetic short circuit release with complete as required. 3 no. 40 amps TPN MCB with thermal over load and magnetic short circuit release with complete as required. | — | — | — | 2,14,760 | |
| — | 2.00 | — | — | ||
| EV CHARGING PANEL (NORTH & SOUTH SIDE) OUTDOOR TYPE PANEL INCOMER:1 no. 250 amps 35 kA FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 250 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 300 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:17 no. 40 amps DP MCB with thermal over load and magnetic short circuit release with complete as required. | — | — | — | 2,78,952 | |
| — | 2.00 | — | — | ||
| UPS I/C PANEL (SOUTH & NORTH SIDE)INCOMER:1 no. 100 amps 4P MCCB 25 KA with thermal over load and magnetic short circuit release 1 SET OF LED LIGHTS FOR RYB INDICATION AND ON/OFF TRIP INDICATION.Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 100 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 160 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:2 no. 63 amps 4P MCCB with thermal over load and magnetic short circuit release with complete as required.1 no. 63 amps 4P MCB with thermal over load and magnetic short circuit release with complete as required. | — | — | — | 2,14,052 | |
| — | 2.00 | — | — | ||
| UPS O/G PANEL (SOUTH & NORTH SIDE)INCOMER:2 no. 63 amps 4P MCCB 10 KA with thermal over load and magnetic short circuit release 1 SET OF LED LIGHTS FOR RYB INDICATION AND ON/OFF TRIP INDICATION.BUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 150 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:2 no. 40 amps 4P MCB with thermal over load and magnetic short circuit release with complete as required.6 no. 25 amps 4P MCB with thermal over load and magnetic short circuit release with complete as required. | — | — | — | 1,93,520 | |
| — | 2.00 | — | — | ||
| PLATFORM LIGHTING PANEL INCOMER:1 no. 63 amps 25 kA FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :1 - set of Three Phase Indicating LampsDigital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 63 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 100 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:40 amps FP MCB ALONG WITH 40A FP CONTACTOR & TIMER HAVING 1 NO. DP RCCB 40A, 30mA AND 8 NOS. 10A SPN MCB IN EACH PHASE- 03 SETS. 40 amps FP MCB ALONGWITH 40A. FP CONTACTOR AND TIMER- 03 SET 40 amps FP MCB- 02 sets | — | — | — | 3,19,308 | |
| — | 1.00 | — | — | ||
| VRV AC O/D PANEL (NORTH SIDE), OUTDOOR TYPE INCOMER:1 no. 250 amps 35 kA FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%- 1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 250 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 300 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:7 no. 63 amps 4P MCB with thermal over load and magnetic short circuit release with complete as required. | — | — | — | 1,29,564 | |
| — | 2.00 | — | — | ||
| RESIDENTIAL METER BOARD PANEL (NORTH SIDE)INCOMER:1 no. 160 amps 25 kA FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 160 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 200 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:11 no. 63 amps TPN MCB with thermal over load and magnetic short circuit release with complete as required ALONG WITH SPARE SPACE FOR ENERGY METER 1 no. 100 amps FP MCCB with thermal over load and magnetic short circuit release with complete as requireD.. | — | — | — | 4,01,200 | |
| — | 2.00 | — | — | ||
| RESIDENTIAL METER BOARD PANEL (NORTH SIDE)INCOMER:1 no. 100 amps 25 kA FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 100 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 150 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:12 no. 63 amps TPN MCB with thermal over load and magnetic short circuit release with complete as required ALONG WITH SPARE SPACE FOR ENERGY METER. | — | — | — | 4,07,572 | |
| — | 4.00 | — | — | ||
| EXTERNAL LIGHTING FEEDER PILLARS (OUTDOOR TYPE)INCOMER:1 no. 63 amps 25 kA FP MCCB with Microprocessor based release with protection functions-overcurrent 40%-100% with time setting,selective short circuit 60%-1000% with time setting ,instantaneous short circuit 150%-1200% complete with :Digital Multifuctional Meter to record demand (KVA), energy (KWH & KVAH), power factor, current (in each phase and the neutral), voltage (between phases and between each phase and neutral), Total haramonic distoration (THD) as a percentage of total current, comprising of suitable communication port for connection to energy management systems. and 1 set of 3 Nos. CT of 63 A/5 A Class 1 accuracy and 15 VA burden. -- 1 SetON/OFF & Phase Indicating lampBUS BAR:Electrolytic high conductivity aluminium three phase and neutral busbars rated at 100 amps having interleaving design throughout having a maximum current density as per IEC 60439 suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity.OUTGOING:25 amps FP MCB ALONGWITH 40A FP CONTACTOR AND TIMER- 06 SETS40 amps FP MCB- 03 sets | — | — | — | 5,66,400 | |
| — | 245.00 | — | — | ||
| Design, Supply, fixing,testing and commissioningof Hot dipped Galvanizedperforated type cable tray600 x 50x 2 mm | — | — | — | 3,58,569.75 | |
| — | 1975.00 | — | — | ||
| Design, Supply, fixing,testing and commissioningof Hot dipped Galvanizedperforated type cable trays450 x 50x 2 mm | — | — | — | 22,84,541.75 | |
| — | 1975.00 | — | — | ||
| Design, Supply, fixing,testing and commissioningof Hot dipped Galvanizedperforated type cable trays150 x 50x 2 mm | — | — | — | 9,09,171.5 | |
| — | 16.00 | — | — | ||
| Supply fixing and commissioning of HT XLPE heat shrinkable type cable end box indoor type size 50 to 185 sqmm as per specification. | — | — | — | 89,136 | |
| — | 40.00 | — | — | ||
| Supply, erection, testing and commissioning of air circulator wall mounting brackets fan blade 400 mm sweep similar with fixing up at suitable height with foundation bolt and clamp etc. as per requirement. Make shall be as per T.S. | — | — | — | 1,94,680 | |
| — | 30.00 | — | — | ||
| Supply, erection (with foundation/supporting structure), installation, testing and commissioning of 10W LED Bollard Light as per specification. Make shall be as per reference list. | — | — | — | 1,49,160 | |
| — | 35.00 | — | — | ||
| Supplying Installation, Testing and Commissioning of Circular/ Rectangular/square LED RGB/ RGBWW/ RGBNW/RGBA/RGBW (as per site requirement) Facade Floodlight/ Projector luminaire for facade lighting with Pressure Die-cast aluminium housing, powder-coated finish, with inbuilt driver of following wattage as given below. The luminaire bracket shall be made of cold-rolled steel & shall be so designed that the luminaire can be tilted to ±90°, the scale shall be provided for rotation degrees. The luminaire shall be IP66 protection also having silicon gasket between optical cover & LED chamber to ensure proper IP66 protection and impact resistance of IK 07. CRI>80, SDCM85%, EMI/EMC as per CISPR-15. There should be options of beam angles of 5/10/15/20/25/30/40/45/60 degree. Luminaire should have efficacy of minimum 35 lm/W for RGB/RGBNW/RGBWW/TNW and 65 lm/W for mono colour options. Luminaire shall be capable of producing dynamic colour changing light for with 16 million colours by DMX/Ethernet based control. The beam angle of the fitting shall be narrow, medium, wide or asymmetric as per the requirement. Luminaire shall be complete with replaceable driver and capable of operating at line voltage without any separate power supply from 100-270 V AC, 50 Hz with power factor > 0.9. Fixture shall be suitable to operate at an ambient temperature range of -10°C to +50°C. Lifetime of complete luminaire(LED ,Driver , Electrical & control circuitry) shall be at least L70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS: (IS 10322) with dully R Number marked and shall be complete with all necessary accessories required for proper working of fixture including connection/inter connection with weather proof ISI Marked copper conductor of minimum size 1.5sqmm connection cables and accessories, Integral male/female water proof connectors IP 67 etc. as required.The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79 report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer, RoHS Compliance. (a)60W | — | — | — | 9,66,420 | |
| — | 20.00 | — | — | ||
| (b) 100W | — | — | — | 8,92,080 | |
| — | 300.00 | — | — | ||
| Supplying Installation, Testing and Commissioning of LED RGB/RGBWW/ RGBNW/ RGBA/RGBW suitable for exterior use having IP67 rating (as per site requirement). Flexible light strip of 5 mtr standard length with 12-15 Watt per meter. Luminaire shall be capable of producing dynamic colour changing light for with 16 million colours by DMX/Ethernet based control. Minimum System lumens 450 lumens/meter and System Lumen Efficacy > 30lm/w. Luminaire light beam spread - 100-110°, The Strip should have IP 67 protection and is offered IP 67 rated connectors to join the LED Strips in continuity. The luminaire must be offered with Aluminium channel for mounting the strip lights. The product should be complete with all accessories and Driver. Lifetime of complete luminaire (LED, Driver, Electrical & control circuitry) 100 DELHI SCHEDULE OF RATES (E&M)-2025 shall be at least L70:50000 burning hours at 50°C. Luminaire shall be conforming to BIS (IS 10322) with dully R Number marked. Luminaire shall be complete with replaceable driver and capable of operating at line voltage without any separate power supply from 24 V DC, Fixture shall be suitable to operate at an ambient temperature range of -10°C to +50°C. The successful bidder shall submit the following certifications/reports for approval before supply of materials: product data sheets, LM79. report from NABL accredited lab, illuminance diagram, polar curve & LM80 report issued by LED manufacturer & RoHS Compliance along with CE certificate. a. 12-15 WATT PER MTR | — | — | — | 22,50,000 | |
| — | 2.00 | — | — | ||
| Supplying Installation, Testing and Commissioning of DMX Controller for the system including address writer and programming the DMX controller with the suitable designs as decided by the Engineer-in-charge/client department ( not less than 10 nos designs) and all other accessories required for the running of the system Controller should have Input Power 5-5.5V DC 0.6A and Output Protocol DMX512 with 4 universe, 2 universe should work in Stand Alone Mode and 2 universe should work in live mode with laptop/ tablet / computer. The universe should be expandable from 2 to 4 DMX512 universes. It should be compatible for Programmability with PC, Mac, Tablet, Smartphone by using USB & Ethernet. Dmx controller should have network controllability feature to control the scene remotely through LAN and triggered via UDP packets on port 2430. It's must have Connections Type C USB, XLR3, Ethernet, battery. There should be provision for Memory microSD card. Device should have Intuitive backlit keyboard with 10 presents and also have provision of keypad on device for changing scene manually from device. Device should be capable to work on Extended triggering possibilities (TCA) & also have Smart Upgrade Technology (SUT). It is an IP 20 unit and has an Operating Temperature of 0°C to 50°C.OS Requirements for the controller is Mac OS X 10.8-10.12, Windows 7/8/10/11. Standards should be EC, EMC, ROHS. The controller should have a variety of features including 2048 DMX channels, clock/calendar, iPhone/iPad /Android remote control, Ethernet facilities, dry contact port triggering and multi-zone SD card memory. Network synchronization of one area across hundreds of 101 DELHI SCHEDULE OF RATES (E&M)-2025 universes with the possibility of 99 scenes across 5 areas with auto clock triggering for sunrise and sunset and as per the festivals for specific occasions. Device should be equipped with meta clamp to mount on wall with data enablers and splitters as required. To be provided with IP 66 enclosure if installed in external environment. | — | — | — | 3,65,800 | |
| — | 7.00 | — | — | ||
| Supply, erection, testing & commissioning of die-cast aluminium 50W LED flood light with toughened glass and high power LEDs and secondary lenses with IP66 protection suitable for highlighting architectural features as per specification. Make shall be as per reference list. | — | — | — | 45,808 | |
| — | 7.00 | — | — | ||
| Supply, erection, testing & commissioning of 150W LED flood light with junction box, suitable for highlighting architectural facade and general purpose lighting with IP 66 Protections & with toughened glass and secondary lenses with IP66 protection. System efficacy 110/120LPW 10KV SPD included as per specification. Make shall be as per reference list. | — | — | — | 1,14,513 | |
| — | 6.00 | — | — | ||
| Supply, fixing, testing and commissioning of storage geyser 25 liter capacity from approved makes. The geyser shall be rated 3 star or above as per specification. | — | — | — | 23,514 | |
| — | 40.00 | — | — | ||
| Provision of single phase electronic meter 0-20 Amp | — | — | — | 43,640 | |
| — | 40.00 | — | — | ||
| Provision of meter box for single phase meter PVC/M.S. with two no. single pole MCB. | — | — | — | 26,080 | |
| — | 3.00 | — | — | ||
| Supply & providing three phase electronic meter 3x240V AC 50Hz of suitable rating, as per spec. | — | — | — | 5,946 | |
| — | 3.00 | — | — | ||
| Supply & providing meter box suitable for three phase electronic meter, as per spec. | — | — | — | 3,498 | |
| — | 3.00 | — | — | ||
| Supply, fixing, testing and commissioning of 32 to 40 Amp. TP MCB C-curve 10KA in existing meter box as per spec. | — | — | — | 3,657 | |
| — | 100.00 | — | — | ||
| Supply & fixing of Bakelite sheet 6mm thick with suitable reg bolt/fasteners and proper fixing in all respect. | — | — | — | 13,900 | |
| — | 40.00 | — | — | ||
| Supply, fixing & commissioning of 300 mm sweep exhaust fan with louver shutter. As per specification. | — | — | — | 58,760 | |
| — | 120.00 | — | — | ||
| Supply, fixing and connecting modular type exhaust fan 225/250mm as per specification. | — | — | — | 1,17,120 | |
| — | 30.00 | — | — | ||
| SFC of bracket fan/ Air circulator 600 mm sweep as per specification | — | — | — | 2,24,040 | |
| — | 421.00 | — | — | ||
| Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes 80 mm dia conforming to IS 3589/1239 part-I for hydrant applications including cutting, screwing, welding etc. & fittings like elbows, tees, flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. Complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required. | — | — | — | 2,99,331 | |
| — | 184.00 | — | — | ||
| Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes 100 mm dia conforming to IS 3589/1239 part-I for hydrant applications including cutting, screwing, welding etc & fittings like elbows, tees, flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. Complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required. | — | — | — | 1,80,136 | |
| — | 950.00 | — | — | ||
| Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes 150 mm dia conforming to IS 3589/1239 part-I for hydrant applications including cutting, screwing, welding etc & fittings like elbows, tees, flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. Complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required. | — | — | — | 13,57,550 | |
| — | 22.00 | — | — | ||
| Providing, installation, testing and commissioning of dual plate non-return valve of 150 mm dia sizes confirming to IS: 5312 complete with rubber gasket, G I bolts, nuts, washers etc. as required. | — | — | — | 1,64,230 | |
| — | 6.00 | — | — | ||
| Providing, installation, testing and commissioning of dual plate non-return valve of 80 mm dia sizes confirming to IS: 5312 complete with rubber gasket, G I bolts, nuts, washers etc. as required. | — | — | — | 18,294 | |
| — | 10.00 | — | — | ||
| Supplying, fixing, testing commissioning of butterfly valve PN 1.6, with Bronze/ Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS 13095, of 80 mm size required. | — | — | — | 30,370 | |
| — | 4.00 | — | — | ||
| Supplying, fixing, testing commissioning of butterfly valve PN 1.6, with Bronze/ Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS 13095, of 100 mm size required. | — | — | — | 16,268 | |
| — | 44.00 | — | — | ||
| Supplying, fixing, testing commissioning of butterfly valve PN 1.6, with Bronze/ Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS 13095, of 150 mm size required. | — | — | — | 2,35,840 | |
| — | 25.00 | — | — | ||
| Providing, Fixing, Testing & Commissioning of single headed oblige pattern hydrant landing valve (internal/external) with 80 mm dia flanged inlet & 63 mm dia instantaneous type female outlet coupling with cast iron wheel complete with cap and chain, twist release type plug and all accessories as per IS:5290-1983(Type-A) of as per approved make.(Gun metal material) | — | — | — | 1,21,825 | |
| — | 50.00 | — | — | ||
| Supplying and fixing of Non-percolating flexible hose (RRL type-A) ISI marked (IS: 636) 63 mm dia, 15 mtr. Long RRL hose pipe with instantaneous type 63 mm dia male and female couplings (IS:903) duly bound and riveted to hose pipes with copper rivets and copper wire etc. as required with Gun metal coupling. | — | — | — | 1,74,250 | |
| — | 25.00 | — | — | ||
| Supplying & fixing Short Branch Pipe with Nozzle, ISI marked, conforming to IS: 903, made of Gun metal material, fitted with 20mm (nominal internal diameter) bore nozzle, for projecting water in form of solid jet. The Branch shall have 63mm Male Instantaneous Inlet, suitable for use with 63 mm size Firefighting hoses. H.P. tested to 21 kgf/cm² for 2.5 minutes. | — | — | — | 35,025 | |
| — | 10.00 | — | — | ||
| Supplying and fixing first -Aid Fire hose reel wall mounted swinging type with MS construction spray painted in post office Red, conforming to IS 884-1985 with upto date amendments, complete with the following as required. (A) 30 m long 20 mm (nominal internal) dia water hose (B)20 mm (nominal internal) dia gun metal globe valve & nozzle 5mm orifice (C)Drum and brackets for fixing the equipments on wall. (D) Connections from riser with 25 mm dia stop valve (gun metal) & M.S. pipe with High Pressure Braided Rubber Hose as per IS:444 Type II, | — | — | — | 57,770 | |
| — | 2.00 | — | — | ||
| Supplying and fixing Fire Brigade In let Connection of CI body with Gun Metal/stainless steel male instantaneous inlet couplings complete with PVC blank cap and chain as required for 150mm dia MS pipe connection, conforming to IS 903 as required of 4 ways. | — | — | — | 19,660 | |
| — | 25.00 | — | — | ||
| Supplying and fixing of Hose Cabinet made of 1.6 mm thick MS sheet with 6 mm thick glazed glass doors including necessary locking arrangement suitable to accommodate external hydrant with butterfly valve, 2 Nos 15 Mtr. Long Hose pipe, 1 No. branch pipe, mounted on wall duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect, for internal/external hydrant complete as required of size 750 mm x 600 mm x 250 mm. | — | — | — | 1,23,300 | |
| — | 8.00 | — | — | ||
| Supplying and fixing air vessel of continuous welded construction fixed at riser top made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia Gun Metal wheel valve, with required accessories, pressure gauge and painting with two coats of Red Oxide and two coat of post office red enamel paint as required (Gun metal material) | — | — | — | 93,680 | |
| — | 4.00 | — | — | ||
| Providing & fixing 100mm dia bourden type, Stainless steel dial type pressure Gauge calibration (0 - 25 Kg/cm2 ) range, 3 / 8 " BSP bottom entry on Pump Delivery Line complete with isolation cock and chrome plated copper pipe | — | — | — | 7,064 | |
| — | 8.00 | — | — | ||
| Supply, installation, testing and commissioning of Sluice valve 150 mm dia. | — | — | — | 95,416 | |
| — | 4.00 | — | — | ||
| Supply, installation, testing and commissioning of Gun metal Ball valve 25 mm dia. | — | — | — | 3,484 | |
| — | 6.00 | — | — | ||
| Providing & fixing vane type water flow switches with contacts for installation in 50 mm to 150 mm dia M.S. pipe for a service pressure up to 20 Kg / Sq.cm | — | — | — | 20,028 | |
| — | 1909.00 | — | — | ||
| Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes 25 mm dia conforming to IS 3589 / 1239 part-I for sprinkler applications including cutting, screwing, welding etc & fittings like elbows, tees, flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. Complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required. | — | — | — | 5,11,612 | |
| — | 639.00 | — | — | ||
| Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes 32 mm dia conforming to IS 3589 / 1239 part-I for sprinkler applications including cutting, screwing, welding etc & fittings like elbows, tees, flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. Complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required. | — | — | — | 2,08,953 | |
| — | 1185.00 | — | — | ||
| Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes 40 mm dia conforming to IS 3589 / 1239 part-I for sprinkler applications including cutting, screwing, welding etc & fittings like elbows, tees, flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. Complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required. | — | — | — | 4,66,890 | |
| — | 657.00 | — | — | ||
| Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes 50 mm dia conforming to IS 3589 / 1239 part-I for sprinkler applications including cutting, screwing, welding etc & fittings like elbows, tees, flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. Complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required. | — | — | — | 3,16,017 | |
| — | 100.00 | — | — | ||
| Providing, Fixing, Jointing, Testing & Commissioning of Heavy duty MS C class pipes 65 mm dia conforming to IS 3589 / 1239 part-I for sprinkler applications including cutting, screwing, welding etc & fittings like elbows, tees, flanges, tapers, reducer, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps, hanger and nuts bolts including cutting hole and chase in brick or RCC walls/ slab and making good the same. Complete with painting of one coats of Red Oxide and two or more coats of synthetic enamel paint of Post office red shade complete as required. | — | — | — | 60,200 | |
| — | 1164.00 | — | — | ||
| 15mm dia, Quartzoid bulb type G.M. Sprinkler Head (Pendent / Upright / Conventional, as required) set to operate at 68OC (UL/FM/LPC/TAC listed/ Approved chrome plated complete with decorating plate (Ressette). | — | — | — | 4,49,304 | |
| — | 40.00 | — | — | ||
| 15mm dia, quartzoid bulb type G.M. Chrome plated side wall extended range sprinkler head set to operate at 68OC (UL/FM/LPC/TAC listed/Approved) complete with decorating plate (Ressette). | — | — | — | 15,520 | |
| — | 6.00 | — | — | ||
| Providing, fixing, testing and commissioning 25mm diameter inspecting and testing assembly with gunmetal isolation valve gunmetal sight glass bypass valve and connected to 50mm drain line. | — | — | — | 20,412 | |
| — | 4.00 | — | — | ||
| Providing & fixing testing & commissioning of installation control valve of cast iron body and brass/bronze working parts comprising of water motor alarm, bronze seat clapper, and clapper arm, hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/Sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc. of size 150 mm dia as required. | — | — | — | 1,24,580 | |
| — | 4.00 | — | — | ||
| Providing, Fixing, Testing & Commissioning of electric driven automatic pressurization horizontally mounted centrifugal END SUCTION back pull out type Hydrant/Sprinkler pump capable of delivering 2280 LPM against a total head of 70 Mtr, 2900 RPM coupled to a suitable HP induction motor including all accessories such as coupling guard, base frame etc as required as per approved make. | — | — | — | 9,55,320 | |
| — | 2.00 | — | — | ||
| Providing, Fixing, Testing & Commissioning of automatic pressurization horizontally mounted centrifugal END SUCTION back pull out type Diesel engine driven stand by pump capable of delivering 2280 LPM against a total head of 70 Mtr, 1800 RPM coupled to a suitable BHP Diesel engine including all accessories such as coupling guard, base frame and etcas per approved make. | — | — | — | 7,93,678 | |
| — | 4.00 | — | — | ||
| Providing, Fixing, Testing & Commissioning of electric driven automatic pressurization centrifugal vertical inline Jocky pump capable of delivering 180 LPM against a total head of 70 Mtr, 2900 RPM coupled to a suitable HP induction motor including all accessories such as coupling guard, base frame and etc as required as per approved make. | — | — | — | 2,78,152 | |
| — | 2.00 | — | — | ||
| Supplying and fixing air vessel of continuous welded construction fixed at riser top made of 450 mm dia, 10 mm thick MS sheet, 2000 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia Gun Metal wheel valve, with required accessories, pressure gauge and painting with two coats of Red Oxide and two coat of post office red enamel paint as required. | — | — | — | 28,962 | |
| — | 10.00 | — | — | ||
| SITC of pressure switches for Main pump/Diesel Engine/Jockey pump including necessary wiring up to control panel and Ball valve. | — | — | — | 22,170 | |
| — | 2.00 | — | — | ||
| ELECTRICAL Fire Control Panel Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter-connection with suitable s i z e copper conductor cable/solid copper strip, h a v i n g switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete a s per CPWD specification with following i n coming and Outgoings, suitable for operation o n 415V, 3 phase, 50Hz A c Supply with enclosure protection class IP 42 as required :Incomings 630A, 50kA 4 Pole MCCB, Ics=100% Icu RatingDigital Voltmeter 0-500V with selector switchAmmeter (0-630 A) with selector swtich & CTs etc.(As per specification) | — | — | — | 18,21,377.2 | |
| — | 4.00 | — | — | ||
| Supply & Fixing ISI marked ( IS : 15683 ) Portable Fire Extinguisher, Mech. Foam type capacity 09 ltrs with gunmetal cap and nozzle and complete respects in all respects including initial fill and wall suspension. | — | — | — | 11,204 | |
| — | 44.00 | — | — | ||
| Supply & Fixing ISI marked ( IS : 15683 ) Portable fire Extinguisher, Carbondioxide type flat base including valve, discharge hose of not less than 10 mm dia. min. 600 mm long & complete in all respects including initial fill with C02 gas confirming to IS:3071966 filled to a filling ratio of not more than 0.667and wall suspension bracket. Capacity 4.5 Kg. | — | — | — | 3,25,028 | |
| — | 44.00 | — | — | ||
| Supply & Fixing ISI marked ( IS : 15683 ) Portable Fire Extinguisher, ABC type, finished externally with red enamel paint, complete in all respects including initial fill and wall suspension of 6 kg capacity. | — | — | — | 1,16,644 | |
| — | 8.00 | — | — | ||
| Supplying and Fixing of fire bucket stand made out of MS angle with one coat of primer and two coat of enamel paint of approved shade including platform and associated civil works each stand should have four nos fire buckets of 24 gauge galvanized steel sheet, standard 9 litre capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters "Fire" in black and gold at approved location as per direction of Engineer in charge. | — | — | — | 31,264 | |
| — | 2.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of UL/EN Listed Analog addressable Fire Alarm system, having the capacity of 99 devices & 99 detectors per loop. The panel shall be able to give location of all fire and More Fire /fault and Isolation conditions of addressable units via the address codes. The panel shall have the capacity of storing up to 1000 events. Further, the panel must be able to automatically switch ON /OFF respective control module whenever any alarm is triggered. The panel should have inbuilt common Alarm, Fault and monitored sounder output. The panel shall have a alpha numeric LCD display and having minimum 160 Characters in the display. The panel shall have a built in power supply and battery charger, 24 V SMF batteries sufficient for 24 hour in standby and 30 minutes in alarm condition and complete as required as per specification. The fire alarm panel should be networkable up to 99 panel & repeater panel. The fire alarm panel shall be compatible for hardware / software integration of PA System. The FACP shall be integrated to Two way fire fighter control system. The FACP shall be able to supervise individual detectors for proper performance as well as to give pinpoint location of Fire or Fault Alarm and initiate Alarms as well as facility for cutting off of AHU's and Electrical Power is also to be included. The panel shall also have the provision through volt-free contact to activate an Auto-Dialler to dial selected phone numbers in case of fire. All addressable units shall be connected to the FACP through the Loop Cards and shall be addressed through individual numbers. The FACP shall be able to obtain analogue value for all detectors in the circuit through a pulsed digitalized current data. The FACP shall be able to analyse all analogue inputs from all addressable units, and through its own software and ambient level screening the FACP shall be able to identify fire, possible fire or fault conditions. Five Loop Fire Alarm Panel with Capability to connect 495 detectors and 495 Devices. | — | — | — | 6,02,258 | |
| — | 2.00 | — | — | ||
| The Alarm Repeater/Annunciator Panel shall display fire/fault messages simultaneously with the FACP. It shall be capable of interfacing with the FACP on a single RS 485 Bus. The panel shall be capable of operating on 24 V DC supply. The panel shall have a 2 x 40 character backlit alphanumeric LCD display, which shall display date, time & description of alarm/trouble events that are displayed in the FACP with an inbuilt buzzer to indicate fault/fire alarm. It shall have control keys for Sound, Silence, and Mute and to reset the FACP from the repeater station. | — | — | — | 1,15,896 | |
| — | 200.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of UL/EN Listed Intelligent Addressable multi-criteria detector (above false ceiling), having optical, thermal Detector shall have twin LED's for 360 degree viewing angle. LED on the detector shall blink each time the sensor is scanned by the FACP. If the FACP determines that the sensor is in alarm, the FACP will Command the sensor LED to remain on to indicate the same. Each Sensor will be capable of being tested for alarm via command from The FACP. Each sensor shall respond to FACP scan with the Information about its type for identification. Sensor Should be supplied with inbuilt isolation feature in its fault condition. | — | — | — | 5,58,600 | |
| — | 20.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of UL/EN Listed Intelligent Addressable multi-criteria detector (above false ceiling), having optical, thermal Detector shall have twin LED's for 360 degree viewing angle. LED on the detector shall blink each time the sensor is scanned by the FACP. If the FACP determines that the sensor is in alarm, the FACP will Command the sensor LED to remain on to indicate the same. Each Sensor will be capable of being tested for alarm via command from The FACP. Each sensor shall respond to FACP scan with the Information about its type for identification. Sensor Should be supplied with inbuilt isolation feature in its fault condition. | — | — | — | 1,960 | |
| — | 26.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of UL/EN Listed loop powered Sounder cum Strobe complete as required as per specification. | — | — | — | 1,05,066 | |
| — | 11.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of Intelligent Analog Addressable Type Manual Call Point having Surface or flush mounting Option fully compliant with Back Box for Mounting Complete as required conforming to BS5839 Standards and Duly Approved by EN54/LPCB/VDS/UL/BSA. | — | — | — | 31,163 | |
| — | 20.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of UL/EN Listed Intelligent addressable Output module having facility to activate AHU, Lifts etc. complete as required as per specification | — | — | — | 66,660 | |
| — | 20.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of UL/EN Listed Intelligent addressable Input module for monitoring purpose complete as required as per specification. | — | — | — | 57,100 | |
| — | 2.00 | — | — | ||
| Drawings for installed FAS System | — | — | — | 8,372 | |
| — | 3100.00 | — | — | ||
| Supply and drawing of 2 Core 1.5 sqmm copper conductor FRLS armoured cable with all required accessories like saddles, Cable glands, junction boxes etc. | — | — | — | 3,53,400 | |
| — | 28.00 | — | — | ||
| Supply of Maintenance free Earth | — | — | — | 3,01,140 | |
| — | 28.00 | — | — | ||
| Installation of Maintenance free Earth | — | — | — | 1,26,840 | |
| — | 300.00 | — | — | ||
| Supply, laying and fixingof 25 x 5 mm GI earthstrip at 0.5 meter belowground level or onwalls/poles / along pipesetc., including connection/ termination with GI nut,bolt, washer etc. asrequired (jointing shall bedone by overlapping andwith 2 sets of GI nut bolt& spring washer spaced at50 mm). Note:- SuitableGI saddles with screwsshall be provided tosecure earth strips run | — | — | — | 52,200 | |
| — | 5500.00 | — | — | ||
| Supply & fixing 6 SWG GI wireon surface or in recess for loopearthing as required. | — | — | — | 3,68,500 | |
| — | 600.00 | — | — | ||
| Supply,installation,testing,commissioning of 600 kWp ongrid solar power plant atroof top of various station buildings and platform shelters,including wall mounted type inverter, SPVarray, Modulemounting structure,Powerconditioningunit, MPPT,controls,protections,interconnectingcables, switchgears,necessaryfeatures tosupplementthe grid power,Power factor>0.9,Operatingtemperature-25 deg. C to+60 deg. C,Solar meter,Net meterapproved byGovt.,Operatingvoltage range200 V to 1000V, max. Inputcurrent 28.5Amp. for eachMPPT,complete withall accessoriesas perattachedtechnicalspecification.(Gridconnectedsolar powerplants are tobe provided onrooftop .Inverter, Solarmeters, netmeters and other accessories asper site requirement may be provided at each of the location as per state electricity board norms.Therefore bidder maykeep in mindwhile quoting the bid for thesame. No extracharge will bepaid by railwayfor the same.) | — | — | — | 2,19,00,600 | |
| — | 2.00 | — | — | ||
| Supply, installation &commissioning roofmounted HVLS fan 12feet dia with allaccessories and suitableC channel with anchorfastners and necessarycivil job as per siterequirement with03years warrantymaintenance. As perspecification. | — | — | — | 4,26,360 | |
| — | 2.00 | — | — | ||
| Supplying and erectionFirst aid box as approvedby St. John AmbulanceBrigade/ Indian Red Crossconform-ing to IS: 2217 -1963 or latest as per spec | — | — | — | 2,458 | |
| — | 2.00 | — | — | ||
| "Providing & fixing of thefollowing equipment as perspecification i. shocktreatment chart dulyframed Bilingual Hindi &English ii. Tool Box:1Setmake Tapariya, Jhalani,etc.{Tool box with items a.Open Jaw spanner -12Nos. 6/7, 8/9,10/11,12/13, 14/15, 16/17,18/19, 20/22, 21/23,24/27, 25/28, 30/32) b.ring spanner-12 nos.6/7,8/9,10/11, 12/13, 14/15,16/17, 18/19, 20/22,21/23, 24/27, 25/28,30/32) c. Ball Hammer-01nos. d. Hexa frame- 01nos. e. C. Plier 210mm-01nos. f. Chiesel 22 x200mm-01 nos. g. Screwdriver 200mm-01 nos. h.Round File 200mm-01 nos.i. Flat file 150mm-01 nos.j. Rachet socket spanner (Rachet-01 Nos. , Handle-03, Socket-01 Nos)-01set} iii. Key Board: 1 Setiv. First Aid Box: 1 Set v.Fire /Sand Bucket: 1Set viPair of Insulated gloves: 1Set vii. Set Earthing rods:1 Set viii. HT and LTDanger Board: 1 Set" | — | — | — | 76,366 | |
| — | 2.00 | — | — | ||
| Supply of Rubber gloves of33 KV grade as per IS4770-68 or latest as perspec | — | — | — | 2,382 | |
| — | 50.00 | — | — | ||
| Providing and fixing oflightning conductor finial,made of 25 mm dia 300mm long, G.I. tube,having single prong at top,with 85 mm dia6 mmthick G.I. base plateincluding holes etc.complete as required. | — | — | — | 31,750 | |
| — | 150.00 | — | — | ||
| Jointing copper / G.I. tape(with another copper/ GItape, base of the finial orany other metallic object)by riveting / nutbolting/sweating andsoldering etc as required. | — | — | — | 20,700 | |
| — | 2175.00 | — | — | ||
| Providing and fixing G.I.tape 20mm X 3 mm thickon parapet or surface ofwall for lightningconductor complete asrequired.(For horizontalrun) | — | — | — | 3,52,350 | |
| — | 530.00 | — | — | ||
| Providing and fixing G.I.tape 20mm X 3 mm thickon parapet or surface ofwall for lightningconductor complete asrequired.(For vertical run) | — | — | — | 1,35,150 | |
| — | 2.00 | — | — | ||
| CENTRAL CONTROL SERVER Supplying Installation Testing Commissioning of Central Control Server System comprising of Intel Xeon CPU E5-2640 x64 (or better) compatible with dual and quad core processors, Windows 11 (Professional, Enterprise, Ultimate, 64 bit), Windows Server 2013 R2 (Standard, Enterprise, 64 bit) 16 GB or more, Video card and monitor capable of displaying at 1024 x 768 resolution or better, Latest Microsoft Licence Version Operating System Loaded with MS OFFICE 2019 Professional, Word, EXCEL, Power Point, Outlook Express, Microsoft Team official version lifetime licences suitable for running BMS software complete etc. as required. | — | — | — | 6,03,570 | |
| — | 2.00 | — | — | ||
| Supplying Installation Testing Commissioning of Client PC System comprising of PC Hardware with minimum11th Gen Intel I7 processor CPU E5-2640 x64 (or better), compatible with dual and quad core processors minimum 3.1 Ghz and 8GB or higher RAM, Hard Drive Space of 256 GB SSD or better, Video card and monitor capable of 1920 x 1080 pixel resolution or better with Ethernet adapter (10/100/1000 Mbps with RJ-45 connector) with 2 GB or higher Graphics card suitable for BMS System complete etc. as required. | — | — | — | 4,08,870 | |
| — | 2.00 | — | — | ||
| Supplying Installation Testing Commissioning of LaserJet printer having printing resolution 1200 x 1200 dpi, (dot/inch) or better, 21 to 30 ppm printing speed (LaserJet) complete etc. as required | — | — | — | 66,339.6 | |
| — | 2.00 | — | — | ||
| Supplying, Installation, Testing and Commissioning of following size LED display (LED monitor) industrial grade with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nits or better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms, Display control shall be on monitor screen and programmable with remote (remote shall be supplied with system), Key Board, Optical Mouse, etc. as required. a. 32 Inch | — | — | — | 69,768.68 | |
| — | 2.00 | — | — | ||
| Software for Building Management System : Supplying Installation Testing Commissioning of Necessary Software (UL listed) Packages containing Building Management with Capability of Collection, Storage, Processing and Controlling all the Data. Software shall support Open Standard Protocols like XML, BACnet, Modbus, Lon works etc. and without the use of Proprietary Protocols, with Enterprise Level Database Like MS SQL complete Lifetime Licenced & capable to collect, store & access all points from Fire Alarm Systems, IT Systems, Automation Systems, HVAC System, Lift, Energy management, Water Management System, etc. to create & monitor historical & event data, event management data, alarm management data & reporting data, Email Alerts for Critical alarms for all the systems. The scope includes additional software required by BMS software (to enable a standard Web browser) to be resident on the DDC/client machine (manufacture-specific browsers shall not be acceptable). User log-on identification and password shall be required & a minimum three-layered security system(User interface Level, Application Level and Data Base Level) to be deployed for safety. The supplied computer software shall employ object oriented technology (OOT) for representation of all data and control devices within the system. This data shall reside on a server for all database access (Systems requiring proprietary database and user interface programs shall not be acceptable). All components and controllers supplied under this contract shall be true "peer-to-peer" communicating devices (Components or controllers requiring "polling" by a Master / Global / Host to pass data shall NOT be acceptable). Physical connection of BACnet/MOD BUS devices shall be via Ethernet at all levels. The License must be provided by default. The BMS software shall be complete in all respect to cater the following different numbers of points managed in the installation. a. DDC Controller-Type-V (Support upto 160 Points) | — | — | — | 7,96,851.64 | |
| — | 6.00 | — | — | ||
| Supplying Installation Testing Commissioning of IP Based DDC controller capable of fully "stand- alone" operation i.e. In the event of loss of communication with other DDC's or Control Station, they shall be able to function on their own. The controllers shall consist of dual/quad core 32 bit microprocessors with EPROM based operating system on BACNET. The network Topology shall not allow single point failure. Each DDC on field level shall have embedded TCP/IP (10/100Mbps) connectivity so that it can be hooked into the Local Area Network (LAN) provided by the client or on dedicated network . Each DDC can be accessed from the Graphical User Interface (GUI) or from a standard Web browser (WBI) by connecting the server alongwith inbuilt web browser. All controllers shall accept 230V+/- 10%, 50Hz Uninterrupted power supply provided by end user. Controller shall support DHCP addressing over Local Area Network (LAN) so that the static IP requirements get reduced however a single static IP shall be provided for system so that it can be hosted on to internet in consultation with end user. The microprocessor based DDC's shall be provided with power supply, analoge to Digital and Digital to analoge converters with memory and capacity to accommodate input/output (I/O) hardware points (with or without an expansion board). Each DDC should have own board and shall accept 0-10 V / 4-20mA input signal having Minimum 20% spare capacity considered for expansion. Each DDC on field level should have minimum 128MB RAM & 64MB Flash memory. Following type of All controllers should be mandatorily BTL approved with B-BC profile complete etc. as required. a. DDC Controller-Type-V (Support upto 160 Points) | — | — | — | 9,91,200 | |
| — | 10.00 | — | — | ||
| Supplying Installation Testing Commissioning of following type of input output (IO) expansion module complete etc. as required. a. I/O Module with 8 UIO channels | — | — | — | 1,72,870 | |
| — | 10.00 | — | — | ||
| (b) I/O Module with 8 DI channels | — | — | — | 1,68,740 | |
| — | 10.00 | — | — | ||
| (c) I/O Module with 8 DO channels | — | — | — | 1,53,400 | |
| — | 1000.00 | — | — | ||
| (c)Cat-6 UTP cable in existing PVC Conduit / Trunking | — | — | — | 76,700 | |
| — | 6.00 | — | — | ||
| Supplying Installation Testing Commissioning of following sizes Powder coated wall mounted lockable and secure enclosure for DDC panel made of 16 SWG sheet steel IP -55 rated with proper internal mounting accessories for DDC such as DIN Rails, terminal block for cable terminations, well dressed for all internal cabling, ferruling, tagging etc. The DDC panels shall have power supply and connections for other peripheral equipment, switchgear protections, isolation transformer, earthing, relays, fuses, auxiliary power output socket & lamp etc. as required. a. 600mmX600mmX200mm | — | — | — | 84,960 | |
| — | 2.00 | — | — | ||
| Supplying Installation Testing Commissioning following type 3rd party Integration unit to provide the interface between Ethernet LAN and the 3rd party field control devices or any other devices which need to be integrated. These shall also provide supervisory capability of functions over the devices connected to it. The purpose of using these units should be limited to integrate the devices only. The Unit must have two onboard Ethernet port, minimum 2/3 on board RS485 ports. The Integration unit should have inbuilt 4GB memory for program storage. The Unit must communicate over TCP/IP with communication speed of 10/100MBPS. The Integration unit should be capable of handling multiple protocol simultaneously such as Bacnet, Modbus, SNMP restricted to single protocol. All integrators should be mandatorily BTL listed. The integration unit shall be housed in suitable size sheet steel enclosure made of 1.6mm thick CRCA sheet, lockable front door with glass, arrangement for cable entry and duly powder coated complete etc as required. a. Integrator for 500 Points | — | — | — | 5,74,872.4 | |
| — | 5000.00 | — | — | ||
| Supply and laying of following size of cables for instrument, controls to DDCs and communication cabling from DDC to central equipment in and including MS Stove enamelled conduit as per IS : 9537 (Part-II). The MS conduit shall be surface mounted on ceiling & embedded in wall including all accessories such as junction boxes, conduit bends, elbows, couplings, end termination including chasing in the wall shall be using cutter and to be filled after laying the conduit. All threaded portion to be painted to arrest corrosion. All Cables shall be ferruled and tagged and shall use lugs for termination at both ends. (a) 2C X 1.5 Sqmm, FRLS insulated copper shielded armoured control cable with fixing accessories such as clamps, saddles etc. | — | — | — | 9,73,500 | |
| — | 4500.00 | — | — | ||
| (b)Cat-6 UTP armoured cable fixing accessories such as clamps, saddles etc. | — | — | — | 6,10,650 | |
| — | 27.00 | — | — | ||
| Light EV AC Charger (Mode-3) Power : 7 kW, Input power supply: 1phase 230 +10% Volt, output supply: 230 Volt AC, Frequency:50 Hz +/-3%, Operational temperature range : -25 to 55 0C (outdoor), -5 to 55 0C (Indoor)., RH upto 95%, Charging Device as per IS-17017-22-1 EV-EVSE Communication: as per relevant IS Codes, Bluetooth Low Energy, one Charge Point Plug/ Socket as per IS-60309 and IS-17017-2, Vehicle Inlet/ Connector As per EV manufacturer, suitable for 2 Wheelers and 4 wheelers. Indoor use: at least IP42; Outdoor use: at least IP54. Mechanical Strength: protection of the external enclosure against mechanical impact shall be IK08 according to IEC 62262.O/L,S/C protection. Insulation Resistance > 1 M . Cable Length: 7.5 m. RCD having a rated residual operating current not exceeding 30 mA; Separate RCD for multiple outputs. Telecommunication port of the EV supply equipment according to IS 13252 (Part 1): 2010. OCPP(Open charge point protocol) 1.6J upgradable to ocpp 2.0. Device Should follow 17017 series of IS codes in general and the installation of the system shall comply with relevant IS Codes. | — | — | — | 9,07,200 | |
| — | 27.00 | — | — | ||
| Installatioon & commisioning Charges for EV charge | — | — | — | 1,59,300 | |
| — | 2.00 | — | — | ||
| WTP Panel:Supply, installation, testing and commissioning of following panel suitable for 415 V, +/- 6% Volts, 3 phase, 4 wires, 50 Hz power distribution system. The panel shall be free standing floor mounting sheet metal enclosed dust and vermin proof conforming to IP-52, compartmentalized design, fabricated out of 14 SWG sheet steel, painting, earthing numbering, danger plate as per specifications and drawings , flush front with Aluminium busbars, separate earth bus bars to be provided throughout the length of the panel. The incoming and outgoing feeder breakers, fuses, indicating lamps etc shall be accommodated in a modular multitier arrangement. The painting shall done as per relevant IS codes/as specified in the specifications. Adequate size cable alley shall be provided all round the panel and in the back for Nos. cable bending and termination. The outgoing feeders inside the panel shall be connected through solid bus bars. Flexible cable links are not acceptable. Nos. set of pumps should be provided with dry running protection, connection from pressure switches, sequencer for alternate running, etc.(As per specification) | — | — | — | 13,39,182 | |
| — | 65.00 | — | — | ||
| Dismantling of existing LT Poles with fittings by digging the foundation and transportation up to the required site as per specification | — | — | — | 33,865 | |
| — | 2.00 | — | — | ||
| Dismantling/shifting the existing lattice LED Light tower/High Mast. | — | — | — | 56,672 | |
| — | 600.00 | — | — | ||
| Supply of material and wiring of shed TP/FP with 1.5 sqmm single core multi-stranded copper wire PVC insulated in conduit 1.5mm thick 19mm size white colour shall be fixed with junction box TEE and 1.5mmsq PVC CU cable insulated multi stranded for earth wire and 5/6A, ceiling rose. The conduit shall be fixed with rawl plugs/ tied with 14 S.W.G. copper wire including connection as per spec. | — | — | — | 1,12,200 | |
| — | 50.00 | — | — | ||
| SFT&C of SPN Distribution Board double door 8 way (8+2 modules), netural and earth link with one no. DP MCB 40A Amp., one no. DP RCCB 40 Amp., 30 mA as incoming and 6 Nos outgoing SP MCB 6/10/16/20/25/32 Amp. 'C' Series, Breaking capacity not less than 10kA. MCB, RCCB & DB should be same make & as per specification. | — | — | — | 2,72,950 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
SPECIALSPECIFICATIONPALISTATION.pdf SPECICAL SPECIFICATION
ATTACHMENT
SPECIALCONDITIONPALISTATION.pdf
ATTACHMENT
114palistationSTD.pdf
ATTACHMENT
ACS1to11ofGCCPALISTATION.pdf
ATTACHMENT
GCCApril-2022_PALISTATION.pdf
ATTACHMENT
SPECIALSPECIFICATIONPALISTATION.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .