Supply, Installation, Testing and Commissioning of HVAC and BMS System for RPO Building, Kolkata

Amount

Total Amount of BoQ 2

Amount after unconditional Rebate

Description of Work / Item(s)

Amount

Total of BoQ 3 and BoQ 4

Total Amount of BoQ3 (Item Rate)

Total Amount of BoQ4 (Percentage Rate)

Description of Work / Item(s)

Amount

Schedule - (B) Bill of Quantites for Non Schedule Items (MR ITEMS)

NS 1 - HVAC Panel

Supply, Installation, testing and commissioning of cubical type LT switchgear suitable for 415V, 3 Phase, 4 Wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work and covers, 3mm thick for gland plates including cleaning & finishing complete with 7 tank process for powder coating in approved shade, having suitable capacity extensible type TPN Aluminium Alloy bus bars of high conductivity, bottom base channel of MS section not less than 100mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with 2.5sq.mm. FRLS insulated copper conductor cable, cable alleys, cable gland plates in two half, i/c providing following 415V Switchgear and accessories in the Panel as per SLD ,specifications complete as required (General arrangement and schematic Drawings to be approved by the Deptt. before start of fabrication) . The Bus bars will be as per the IEC 6068-3-247 Standard.

Also, refer to General Notes and Specifications for Panels/ Boards.

All Switchgear makes shall be from approved List of makes.

Only one make of switchgear to be used in a board / Panel.

All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The busbars insulation shall be with heat shrinkable sleeves. SMC shrouds busbar supports shall be used.

Minimum Air Clearances between bus bars;

As per CPWD Specification

a- GENERAL NOTES FOR MCCB's:

MCCB's shall be of 3P with solid neutral link or 4P as called for in the BOQ.

Ics = Icu for the breakers.

MCCB's upto 200A shall be with thermal - magnetic releases and beyond 200A shall be with micro-processor based releases.

MCCB's upto 100A shall have fixed over current and fixed short circuit setting and breaking capacity for 1 Sec.

MCCB's above 100A but upto 200A shall have adjustable over current and fixed short circuit setting and breaking capacity for 1 Sec.

MCCB's shall be with extended rotary handle and Phase separators both sides

MCCB's shall have auxiliary contacts wherever BMS compatibility is needed.

MCCB of required rating (Amps) as called for in the BOQ and of required breaking capacity for 1 Sec.

b- GENERAL NOTES FOR MCB's:

MCB's shall be of minimum 10kA breaking capacity for 1 sec.

Exact MCB rating & category is to be calculated by the electrical contractor based on the final load of the circuit, its nature and fault current.

c- All Panels Should have provision of Multi Function Meter with required number of MCB's, Indicatuion Lamp, Control circuitry etc as required.

d- All the outgoing of panels for jet fans should be fire rated as per NFPA.

NS-1.1 : MDB Ventilation Panel

Incomer:-

1 Nos. 315 Amps FP MCCB of fault breaking capacity 25KA (Ics=Icu)

BUSBARS SECTIONS

400 amps FP, 25kA, 480volts grade busbar chamber of suitable length with Al busbars. All busbars and interconnections shall be of suitable size Al busbar, current density of bus-bars shall not be more than 0.8 Amps/ sq.mm cross sectional area of Bus Bar.

OUTGOING

3 Nos. Of 100 A FP MCCB

5 Nos. Of 25 A FP MCCB as SPARE

NS-1.2 : JET FAN PANEL (BASEMENT 1)

INCOMER (63A MCCB)- 1 Nos

63A 4P 25KA THERMAL MEGNETIC BASED MCCB WITH O/L & S/C RELEASED, EXTENDED OPERATING HANDLE, 1C/O AUX. SW. + TAC

BUSBARS SECTIONS

100 amps FP, 25kA, 480volts grade busbar chamber of suitable length with Al busbars. All busbars and interconnections shall be of suitable size Al busbar, current density of bus-bars shall not be more than 0.8 Amps/ sq.mm cross sectional area of Bus Bar.

R-PHASE INDICATION LAMP (RED), LED TYPE, 230V AC

Y-PHASE INDICATION LAMP (YELLOW), LED TYPE, 230V AC

B-PHASE INDICATION LAMP (BLUE) , LED TYPE, 230V AC

ON/OFF/TRIP INDICATION LAMP (RED/GREEN/AMBER) , LED TYPE, 230V AC

60/5A, 15VA, CL-1, RESIN CAST CT FOR METERING

DIGITAL AMMETER, CL-1, SIF 96X96 SQMM

DIGITAL VOLTMETER, CL-1, SIF 96X96 SQMM

6A SP C-CURVE MCB, 10KA

NEUTRAL LINK

OUTGOING FEEDER- 18 Nos

MCB FEEDER

16A 4P C-CURVE MCB, 10KA for spare

NS-1.3 : JET FAN PANEL (BASEMENT 2)

INCOMER (63A MCCB)- 1 No.

63A 4P 25KA THERMAL MEGNETIC BASED MCCB WITH O/L & S/C RELEASED, EXTENDED OPERATING HANDLE, 1C/O AUX. SW. + TAC

BUSBARS SECTIONS

100 amps FP, 25kA, 480volts grade busbar chamber of suitable length with Al busbars. All busbars and interconnections shall be of suitable size Al busbar, current density of bus-bars shall not be more than 0.8 Amps/ sq.mm cross sectional area of Bus Bar.

R-PHASE INDICATION LAMP (RED), LED TYPE, 230V AC

Y-PHASE INDICATION LAMP (YELLOW), LED TYPE, 230V AC

B-PHASE INDICATION LAMP (BLUE) , LED TYPE, 230V AC

ON/OFF/TRIP INDICATION LAMP (RED/GREEN/AMBER) , LED TYPE, 230V AC

60/5A, 15VA, CL-1, RESIN CAST CT FOR METERING

DIGITAL AMMETER, CL-1, SIF 96X96 SQMM

DIGITAL VOLTMETER, CL-1, SIF 96X96 SQMM

6A SP C-CURVE MCB, 10KA

NEUTRAL LINK

OUTGOING FEEDER-18 Nos

MCB FEEDER

NS-1.4 : Staircase Pressurisation- 1 & 2 (TENANT & RITES)

INCOMER- 1No.

1 Nos. 32 Amps TPN MCCB

BUSBARS SECTIONS

40 amps TPN, 10kA, 430volts grade busbar chamber of suitable length with Al busbars. All busbars and interconnections shall be of suitable size Al busbar, current density of bus-bars shall not be more than 0.8 Amps/ sq.mm cross sectional area of Bus Bar.

OUTGOING

NS-1.5 : Lift well Pressurisation Panel-1 & 2

INCOMER (32A MCCB)- 1 No.

32A TP+NL(SEPARATE NEUTRAL LINK) 25KA THERMAL MEGNETIC BASED MCCB WITH O/L & S/C RELEASED, EXTENDED OPERATING HANDLE

BUSBARS SECTIONS

40 amps TPN, 25kA, 430volts grade busbar chamber of suitable length with Al busbars. All busbars and interconnections shall be of suitable size Al busbar, current density of bus-bars shall not be more than 0.8 Amps/ sq.mm cross sectional area of Bus Bar.

R-PHASE INDICATION LAMP (RED), LED TYPE, 230V AC

Y-PHASE INDICATION LAMP (YELLOW), LED TYPE, 230V AC

B-PHASE INDICATION LAMP (BLUE) , LED TYPE, 230V AC

6A SP C-CURVE MCB, 10KA

NEUTRAL LINK

OUTGOING- 3Nos

Construction of LT panel as per IS-8623 ( Part-I) Standard

Variable Refrigerant Flow system

NS-2: DX Type Air handling unit: Supply,installation,testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower,multispeed motor,coil section with DX copper coil,electronic expansion valve,corded remote control,outer cabinet,vibration isolators,drain pan,other necessary supports etc.,suitable for operation on single phase AC supply 230V±10%,50Hz complete as required.The unit shall have automatic force shutdown provision in case of fire on receiveing signal from BMS System.The cooling capacity of indoor unit will be at air-inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. Mid Static Ductable units (minimum 45 pascal external static pressure)

NS-2.1:16.7 TR, 6600 CFM TR (min.) Ductable unit with remote control

NS-2.2: 13 TR, 5000 CFM Ductable unit with remote control

NS-2.3: 11 TR, 4400 CFM Ductable unit with remote control

NS-3: Supply ,Installation, testing and commissioning of energy efficient 2.5 TR 5 star split AC Cassette type indoor unit.

NS-4:Supply ,installation, testing and commissioning of Air Curtains velocity 13 m/sec 1.5 m and 2 meter width with sensor. The air curtain shall be in complete S.S construction with fan & motor assembly. The motor shall be with single phase electrical connection. The air curtain shall be designed to throw a minimum of 10 feet vertically downward distance.The unit shall be sleek & slim and should occupy minimum space. The noise level shall not be more than 55 DB.

NS-5: Supply, installation, testing and commissioning of copper conductor 2 C x1.0 sqmm Control cabling in existing conduit from indoor to outdoor unit.

NS-6: Supply, installation, testing and commissioning of copper Refnets for VRV System (To be supplied by unit manufacturer) Vendor is expected to minimise no. of joints that is required for a complete installation.

NS-7: Supply, installation, testing and commissioning of drain piping using CPVC pipe SDR11 upto 50mm & above size SCH 40 with CPVC fittings and insulated with 6mm thick nitrile rubber insulation finished with polished. The pipe goes below ground should be rapped with polythene sheet.

NS-7.1: 100 mm Dia

NS-7.2: 50 mm Dia

NS-7.3: 40 mm Dia

NS-7.4: 32 mm Dia

NS-8: Supply, fabrication and installation of MS base frame for outdoor units complete with 2 coat of epoxy painting, vibration isolation pads, supports, hangers, railing, brackets etc. Apply 2 coats of epoxy primer 2 coats of epoxy paint and finish painting. Stand to be made as per site conditions.

NS-9: Supply, installation, testing & commissioning of thermal insulated flexible duct of 50 mm dia duly supported at regular interval as per site requirement etc. complete as required as per specifications.

CENTRIFUGAL EXAHUST FANS (TOILET - CENTRAL)

NS-10: Supply, installation, testing and commissioning of the following SISW type centrifugal fans with backward curved inclined type heavy duty class with 3 Phase TEFC with IP 55 protection class F insulation, eff-3 complete with base frame to mount fan motor with adjusting brackets, vee drive belt and belt guard, vibration spring isolators, canvas connection and epoxy painted all as per specs. All accessories louvers, bird screen, Mounting racket, Stand or Hanging arrangement & electrical cable connection necessary for Fan Units are included. Sound level of fan should not exceed 67db(A) @3 mtr in Room condition, it should be AMCA certified.

NS-10.1: 6000 CFM, 50 mm S.P.

NS-11.1: Lift Press. Fan , 11000 CFM, 40 mm S.P.

NS-12.1: Staircase Press. Fan , 5000 CFM, 40 mm S.P.

NS-13.1: 30000 CFM, 20 mm S.P. (Normal Mode )

NS-14.1: 30000 CFM, 20 mm S.P.(Fire Mode)

Centrifugal Jet Fan

NS-15: Supply, Installation, Testing and commissioning of approved makes Induced Air Centrifugal Jet fans. Fan shall be AMCA certified for Air & Sound performance, balanced to vibration grade of G2.5 as per AMCA 204. Fan shall be complete with GSS casing ( 220 GSM ), MS impeller, Dual speed smoke venting Class H, special rated motor certified for 250 Deg C for 2 Hrs - 415/3P/50Hz.Complete Fan & motor assembly shall be Tested & certified for 250 Deg C for 2 Hrs. Sound level of fan should not exceed 67db(A) @3 mtr in Room condition CFM-4200/2200

NS-16.1: 24000 CFM, 20 mm S.P. (Normal mode)

NS-17.1: 24000 CFM, 20 mm S.P. (Fire mode)

Fresh air fan for VRF indoor unit fresh air supply

NS-18: Supply, installation, testing and commissioning of the cabinet type centrifugal fans with backward curved inclined type heavy duty class with 3 Phase TEFC with IP 55 protection and class F insulation complete with base frame to mount fan motor with adjusting brackets, vee drive belt and belt guard, vibration spring isolators, canvas connection and epoxy painted, with filter box (pre and fine filter) all as per specs. All accessories louvers, bird screen, Mounting racket, Stand or Hanging arrangement & electrical cable connection necessary for Fan Units are included.Sound level of fan should exceed 67db(A) @3 mtr in Room condition. Fan & cabinet (complete Unit) should be AMCA certified.

NS-18.1: 11000 CFM fan, 50 mm static

Air Purification System

NS-19: Supply, Installation, Testing and commissioning of Air Purification system to improve Indoor air quality by using Bi-polar Ionization technology, producing equal amounts of positive and negative ions. Project design should meet standard ASHRAE 62.1 IAQ Procedure for energy saving. System should kill microorganism and pathogens, remove Odour, VOC and reduce dust particle /particulate matter / PM2.5 /PM 10. The product should be UL / Intertek listed. Product should have minimal or negligible pressure drop & low power consumptions.

NS-19.1: Ductable Units at Second Floor

NS-19.1.1 16.7 TR/ 6600 CFM

NS-19.1.2:13 TR/ 5000 CFM

NS-19.1.3: 11 TR/ 4300 CFM

NS-19.2: Cassette Units- (1st Floor to 12th Floor)

NS-19.2.1:1.5 TR to 4.0 TR

NS-19.3: Fresh Air Units (TFA)

NS-19.3.1: 11000 CFM

Cable

NS-20: Supply of XLPE armoured cable 3 core 4 sq. mm. copper conductor PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade .

NS-21: Supply of XLPE armoured cable 3 core 2.5 sq. mm. copper conductor PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade .

NS-22: Supply of 1.1 kV LT cable having aluminium conductor PVC insulated, extruded inner sheathes, galvanized, steed strip confirming to IS 3975:1990 & extruded PVC outer sheathed armoured cable with specified IS-1554 Part-1:1988

NS-22.1: 3.5 x 50 sq.mm

NS-23: Supply of PVC / XLPE ARMOURED Cables with COPPER Conductor 1100 V. Grade

NS-23.1: 4 C x16 sq.mm

NS-23.2: 4 C x 10 sq.mm

NS-23.3: 4 C x 6 sq.mm

NS-24: Supply and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required

NS-24.1: 4 C x 6 sq.mm

NS-24.2: 3 C x 4 sq.mm

NS-24.3: 3 C x 2.5 sq.mm

BMS: BUILDING MANAGEMENT SYSTEM

NS-25: BMS System Software : Supply, installation, testing and commissioning of the unlimited multi user with simultaneous minimum 5 user Web Based Graphical Software meeting the requirements in the Given I/O Summary and technical specifications including configuration and facility to create / provide the graphic mapping for all I/O Summary points , animate the Graphics, Navigation between pages, display of logs, changing the time zones, popup alarms, configurable password protection for Building Mgmt System as per Specifications. Software shall be able to communicate with open protocols like BACNet, Modbus devices simultaneously. Offered software shall have builtin feature for EMS, Alarming, reporting, scheduling & trending. The software shall have unlimited software & Hard ware capacity. During operation & maintenance if any controllers required to replace than software shall have feature to download logics in new controller as of old one, from control station, once the old controllers ip is maped in new one.

NS-26: Supply Installation, testing Commissioning of Central Server with the minimum following specifications,: Intel® Xeon® processor E3, 3.2 GHz, 4 Core, 8MB Cache memory, Intel HD Graphics , 1TB HDD, 16 GB Ram Rack Mount with Server Database OS & loaded with lifetime license. The server shall have only Ethernet port for browsing and configuring BMS Software

NS-27: Supply,Installation,Testing and Commissioning of A-4 size Black and White laser Printer.

NS-28: SYSTEM INTEGRATION UNITS FOR 3RD PARTY SYSTEM SOFTWARE INTEGRATION - UL listed Controllers. Supply, installation, testing and commissioning of Bacnet IP/Lonmark IP852 (open Protocols) Integration units, to connect individual 3rd party microprocessor system controllers like Chillers & fans etc. the unit shall be capable of integrating all mentioned devices on BACnet, Modbus & LON etc.as per distribution given below :

NS-28.1: UPS - 23 nos

NS-28.2: VAV's Integratuions - 29nos.

NS-28.3: Diesel Generator - 2 nos.

NS-28.4: HT Panel & LT Panels

NS-28.5: Fire Alarm System

NS-28.6: Lifts - 9 nos.

NS-28.7: Water metre - 5 nos.

NS-29: PROGRAMMABLE & APPLICATION SPECIFIC CONTROLLER (DDC) - Supply, installation, testing and commissioning of Bacnet IP/Lonmark IP852 (open Protocols) Direct Digital Controllers, The networkable controllers shall be , UL and BTL/Lonmark IP852 certified, vendor shall submit BTL/Lonmark IP852 certificate along with bid) with 32 bit microprocessor, real time clock & programmable memory. The Controller shall have built-in two Ethernet ports. preferably Each DDC and IO module shall have built in LCD display & dial/button for local control & monitoring. The networkable DDC's shall be capable of peer to peer communication with lockable MS mounting cabinets duly powder coated connector strip, internal wiring and space to house controller & relays, connector etc. as per IO Summary. The Controller shall have built in memory to save graphics & logis for the connected points. The controller shall have minimum 15% spare IO capacity. Any Multiplexer (Mux) / AI to DI / DI to AI converters shall not be allowed. The DDCs shall be with suitable IP 67 enclosure complete with all wiring and accessories

Hard Points(As per IO Summary) HVAC Part

NS-29.1: Ceiling Suspended Unit

NS-29.2: Casette Units - per Floor - Monitoring and Controlling

NS-29.3: Ventiallation System + Pessurisation FAN

NS-29.4: Diesel Generator

NS-29.5: HT Panel & LT Panels

NS-29.6: Fire Fighting System

NS-29.7: Plumbing System

NS-30: Supply Installation, Testing & Commissioning of the below sensors as per VRF system

NS-30.1: Duct Type Temperature Sensors + Humidity Sensor

NS-30.2: Water Level Switch

NS-30.3: Oil Level Sensor

NS-30.4: Outdoor Temp +humidity Sensor

NS-30.5: Water Flow Meter

NS-30.6: PH Sensor

NS-30.7: TDS Sensor

NS-30.8: Room Temperature Sensors + Humidity Sensor

NS-30.9: Water Pressure sensor

NS-30.10: DC Voltage Transducer

NS-30.11: Flame proof Level switch

NS-30.12: Air Differntial pressure switch for AHU

NS-30.13: CO2 sensor for Jet fans

NS-31: Supply, installation, testing and commissioning of Copper Control Cabling for instrument, controls to DDCs and communication cabling from DDC to central equipment complete with clamps etc complete. All Cables shall be ferruled and tagged.

NS-31.1: Supply,testing and commissioning of 2 Core x 1.5 sq mm Armoured Cable for control cabling

NS-31.2: Supply ,installation,testing and commissioning of 4 pair UTP Armoured Cat 6 cables

NS-31.3: Supply,Installation, testing and commissioning of 3 Core x 1.5 sq mm Armoured Cable

NS-32: Supply, Installation, Testing & Commissioning of Layer 2 Switch 24 port as per the given Specification etc. all complete.

CCTV SYSTEM

NS-33: SITC of 4MP Bullet camera 2048 x 1536 at 30fps, Autofocus Motorized remote zoom lens 2.8 - 8 mm, H.265/H.264 compression, internal/external 40mtr Adaptive IR, 120dB true WDR as per IEC , Sensitivity 0.01lux color, 0 lux (IR ON) B/W Mode, 3D noise filtering, Bi directional Full Duplex Audio, 1 Alarm In, 1 Alarm out, 3 independant stream, Audio Compression: G.711a, G.711u, AAC, min 4 nos. of privacy mask, Supported protocol - TCP/IP, Ipv4 & IPv6,UDP/IP, DNS, DDNS,ARP, ICMP, IGMP, RTCP, TSL, Edge based analytics - Motion Detection, Camera Sabotage, Audio Detection, Object Counting, Adaptive Motion, Object Removal, and Directional Motion. Camera shall features of Corridor mode, Mirror mode, to ruggedized performace camera should meet Shock & Vibration Certifcation: IK10 Camera should having SD card provision of 128 GB,Contruction:Aluminium dicast, Operating temperature -40 to +60deg C, IP 67, IK10,Type 4 X Certification, Works on PoE , 24VAC & 12 VDC, Power consumption <30W, ONVIF profile S,G,T Certification: CE, FCC, UL60950-22, IP67, IK10, BIS, with Complete Mounting accessories as required, Cybersecrutiy Cert:UL/NDAA

NS-34: SITC of 1/2.8", 2Mpx IR PTZ dome camera 1920 x 1080 at 60fps, Focal length 6 - 135mm or better, Horizontal angle of view: 59 deg (wide) ~ 2.34° (tele); H.265, H.264 compression, 150mtr Adaptive IR, 100 dB true WDR as per IEC 62676. 0.025lux at color, 0.01lux at Mono, 3D noise filtering, Shutter range: 1 ~ 1/10,000 sec,Electronic image stablization, Bi directional Audio In/Out, Audio Compression: G.711a, G.711u, AAC, 2 Alarm In, 1 Alarm out, Edge based analytics - Motion Detection, Camera Sabotage, BLC, protocol support -IPv4 & Ipv6,802.1x (EAP), TLS1.2, ICMP, IGMP, DNS, DHCP, TCP/IP. Pan 360deg continuous, Tilt range: + -15 to - +90 deg, Pan preset speed: 300°/sec; Tilt preset speed: 145°/sec, 256 presets, 16 tour, 4 pattern, having SD card provision of 256 GB, Aluminium dicust construction, min 04 configurable pivacy masks,Operating temperature -40 to +60 deg C, IP66, Type 4X Certificaiton, IK10 Enclosure, 24 VAC & 48 VDC, ONVIF profile S,G ,T ,UL, CE, FCC, BIS certified. With require accessories wall mount, pole bracket etc

NS-35: SITC of 4 Mpx Indoor dome camera 2048 x 1536 at 30fps, Autofocus Motorized remote zoom lens 2.8 - 12mm, H.265, H.264 compression, min 40 mtr IR, 120 dB true WDR as per IEC 62676. Sensitivity 0.01lux color, 0 lux (IR ON) B/W Mode,3D noise filtering, Bi directional Full Duplex Audio, inbuilt mic, 1 Alarm In, 1 Alarm out, Audio Compression: G.711a, G.711u, AAC, 3 independant stream, min 4 nos of configurable privacy mask, Supported protocol - TCP/IP, Ipv4 & IPv6, UDP/IP, DNS, DDNS,ARP, ICMP, IGMP, RTCP,TSL. Edge based analytics -Object Counting, Adaptive Motion, Object Removal, Motion Detection, Camera Sabotage, Audio Detection, and Directional Motion. Camera shall features of Corridor mode, Mirror mode, having SD card provision of 128 GB , Operating temperature -10 to +55 deg C,IP64,IK10,Works on PoE, 24 VAC & 12VDC, Power consumption 12W, ONVIF profile S,G, Certification: CE, FCC, UL, IK10, BIS, with Complete Mounting accessories as required With require accessories wall mount, pole bracket etc. Cybersecrutiy Cert:UL/NDAA,Shock & Vibration Certifcation:IEC 60068:2-6 and 2-27

NS-36: Supply installation Testing and Commissioing of Video Management Recording servers .it should supports upto 128 cameras for future upgradation .It should have Intel® Xeon® Silver 4210 or better with 16 GB DDR4 ECC RAM or better. It should run on Windows® 10 IoT Enterprise 64-bit (LTSB) or latest .It should have M2. SSD 2 x 480 GB for operating system.Shall support Dynamic Host Communication Protocol ( DHCP ) and Network Time Syncronisation Protocol ( NTP ) functionality. It shall have Mapping function. It should support RAID 6 .It should have dual power Supply.It should have in built plugins to integrate third party systems. It shall have min 8 HDD slots . Each Box should have Thoughput should be 450 Mbps. ,*Video Outputs- 4x Mini Display port 1.4 ,*VMS Should support ONVIF S,G & T ,Should have NVIDIA Quadro P620 2 4 GB memory card ,Should have 2xGigabit Ethernet (1000Base-T) ports,

NS-37: Supply Installation, testing Commissioning of CCTV client work station with the minimum following specifications,: Intel® Xeon® processor E3, 3.2GHz, 4 Core, 8MB Cache memory, Intel HD Graphics , 1TB HDD, 16 GB Ram Rack Mount with Server Database OS & loaded with lifetime license. The server shall have only Ethernet port for browsing and configuring BMS Software

NS-38: Supply installation Testing and Commissioing of Video Management Softwarwe VMS should have smart motion Search for server side motion detection and quick retrieval of events *Edge Storage Auto Gap Fill functionality detects when a gap in local camera recording occurs, and automatically downloads video and audio (if present) to fill the gap *web based client allows viewing and exporting video without installing any softwar *Imports users and roles from existing LDAP servers to reduce administrative overhead, and enables single sign-on (SSO) *Capable of listening for ASCII commands on a serial and Ethernet port simultaneously *Supports shared displays so operators can send video to surveillance personnel who need it most *Check on VMS and camera health using SNMP *Supports IPv4 and IPv6 cameras *Enables and supports Risk Management Framework (RMF) *TLS-based encryption over HTTPS *Extensible through mapping and plugins, including video information overlays and license plate recognition *should include feature, which is capable of polling for alarms from devices and performing specified actions when an alarm state change occurs *Incorporates FIPS 140-2 validated cryptographic modules. To ensure seamless deep integration VMS should be of same camera OEM.

NS-39: Supply, installation Testing commissioning of 43" LED FULL HD Display. Spec: Display Size-43" signage category, Panel Technology: IPS, Resolution:1920X1080, brightness: minimum 350cd/m2, Interface : HDMI(2), DVI, DP, RGB, RJ45, IR, RS232C,

NS-40: Supply, installation Testing commissioning of 42 U Rack with glass front door, steel rear door, power supply, MCB, cable manager, drawer shelves and wiring channels to accommodate CCTV systems equipment and accessories as mentioned in the BOQ above and including all connections and terminations as required.

NS-41: SITC of 24 port 10/100/1000BASE-T PoE+, 2 1GbE unpopulated SFP ports, 1 Fixed AC PSU, L2 Switching with Static Routes, 1 country-specific power cord, POE Budget- 185W

NS-42: Supply, and laying of 4 pair Category 6 cable consisting of 23 AWG solid copper conductors and as per the specification. The cable shall have flexible jacket and ripcord for easy Stripability support upto 650 MHz.

NS-43: Supply, Installation and Commisioning of Full Functionality Keyboard for fixed/variable speed and PTZ.Should have Preset Position and Pattern Control, Joystick Control of PTZ Functions, Auto/Random/Frame Scanning,

NS-44: Supply, Installation, Testing and Commissioning of following Category 6, toolless patch panel 24 port prepackaged with 4 block insert labels, label holders, metal back panel, an instruction sheet for termination of incoming pairs.

NS-45: Supply and fixing of Cat 6 Patch cord - 1 mtr

NS-46: Supply and fixing of Cat 6 Patch cord - 3 mtr

DATA SYSTEM

NS-47: Supply, installation, testing and commissioning of 6 pair Single Mode fibre optic armoured cable as per the specification.

NS-48: Supply, Installation, Testing and commissioning of of 6 port LIU Loaded with Pigtail and Adaptor

NS-49: Supply, Installation, Testing and commissioning of of 48 port LIU Loaded with Pigtail and Adaptor

NS-50: Supply, Installation, Testing and commissioning of 2 Mtr FO SC-LC Patch cord

NS-51: Supply and installation of flush mounted Enhanced Category 6 T 568 A or B) outlet. The plastic shall be high impact, flame-retardant, UL rate thermoplastic

NS-51.1: Supply , installation, testing and commissioning of Single outlet faceplate with Toolless RJ-45 jack with information outlet, ust cover / blank shall be provided to protect unused faceplate openings. Termination caps and plastic cover shall be provided to protect jack wiring.

NS-52: Supply, Installation , Testing and Commissioning of following 19 inch width rack for ethernet switches with A.C. distribution box, wire manager, fan tray, lockable front tinted glass door and two pair angle to support the switch installed in the rack.

NS-52.1: 42 U Rack x 800 mm x 100 mm

NS-52.2: 12 U Rack x 600 mm x 600 mm

NS-52.3: 9 U Rack x 600 mm x 600 mm

WiFi Router

NS-53: Supply, installation, testing and commissioning of INDOOR 802.11AC AP, Dual radio

NS-54: Supply, installation, testing and commissioning of WLAN Controller for AP

NS-55: Supply, installation, testing and commissioning of following Category 6, toolless patch panel 24 port prepackaged with 4 block insert labels, label holders, metal back panel, an instruction sheet for termination of incoming pairs.

NS-56: Supply, installation, testing and commissioning of 48 port 10/100/1000BASE-T, 4 1GbE unpopulated SFP ports, 1 Fixed AC PSU, L2 Switching with Static Routes, 1 country-specific power cord

NS-57: Supply, installation, testing and commissioning of 24 port 10/100/1000BASE-T, 2 1GbE unpopulated SFP ports, 1 Fixed AC PSU, L2 Switching with Static Routes, 1 country-specific power cord

NS-58: Supply, installation, testing and commissioning of 12 nos. 10GSFP + port Core switch

NS-59: Supply, installation, testing and commissioning of 10G SFP FO Module

NS-60: Supply and fixing of Cat 6 Patch cord - 1 mtr

NS-61: Supply and fixing of Cat 6 Patch cord - 3 mtr

TELEPHONE SYSTEM

NS-62: Supply, installation, testing and commissioning of EPABX with Redundant configuration in processor and power supply level, primarily configured for 624 users and expandable upto 10,000 users in future by adding additional peripheral cards:- 1. 600 nos. analog subscribers 2. 24 nos. digital subscribers 3. 8 nos. alanlog PSTN CO Trunk 4. 1 no 30 channel PRI 5. 1 no. PC based operator console with hardware 6. Auto attandant

NS-63: Supply, installation, testing and commissioning of Digital Telephone Set

NS-64: Supply, installation, testing and commissioning of Analog Telephone Set with CLI

NS-65: Supply, installation, testing and commissioning of Analog Telephone Set without CLI

NS-66: Supply, installation, testing and commissioning of MDF patch panel prepackaged with wiring block with legs, insert labels, label holders, jumper troughs, metal back panel duct assembly, screws washers and an instruction sheet for termination of incoming pairs. Rate shall include suitable size of lockable 1.6mm thick CRCA sheet steel enclosure duly powder coated. The cost shall be complete with fixing arrangements, foundations etc as required

NS-66.1: 600 pair Distribution Box (MDF/IDF)

NS-66.2: 60 pair Distribution Box (MDF/IDF)

NS-66.3: 20 pair Distribution Box (MDF/IDF)

NS-66.4: 10 pair Distribution Box (MDF/IDF)

NS-67: Supply, installation, testing and commissioning of Riser cable consisting of multiple core or solid copper conductors of 24 AWG size insulated with expanded polyethylene covered by a PVC skin and inner shielding for grounding. The core shall be covered by a layer of plastic tape and overlaid with a corrugated PVC plastic.

NS-67.1: 100 Pair

NS-67.2: 50 Pair

NS-67.3: 10 Pair

NS-68: Supply and installation of flush mounted Category 6 T 568 A or B outlet with G.I back box of adequate depth for good termination and all required accessories. The plastic shall be high impact, flame-retardant UL rated thermoplastic. Dust cover / Blank shall be provided to protect unused face plate openings. Termination cap and plastic cover shall be provided to protect jack wiring.

NS-68.1: Single outlet face plate with RJ-11 jack

UNINTERPTUD POWER SUPPLY

NS-69: Supply, installation, testing and commissioning of 3 KVA UPS with 1 Hour Backup (1Ph Input /1Ph Output), True On-line Double Coverstion UPS,Built-in solid state float-cum-equalizing charger with automatic boost / trickle charge modes with current limiting features.Battery Type-12 V Sealed Lead Acid Maintenance Free.RS232 Port and optional USB port and SNMP Card for connecting the UPS to LAN.Static Bypass should be provided.Warranty-2 Years on UPS & Battery.

Operation of Electro Mechanical system ( As per BOQ) for defect liability period.

NS-70: Operation and routine maintanance of Electro-Mechanical Services and other facilities as detailed in BOQ for 1st Year i.e., Defect Liability Period having HVAC System, 33/0.433KV Substation & DG Set, Lift, Fire alarm and Fire Fighting System IBMS System, Solar Panel/Solar Work, Sewage Treatment Plant, Water Supply etc as specified in the BOQ .

Bidder Name

Amount

Airef Engineers Pvt Ltd(GSTN-NA)