Civil works for the proposed shifting of customer service centre from ground floor of Max-I TE building to adjacent RLU Building, KPHB, Hyderabad.

Amount

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in foundation and plinth in:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.20 mm M.S. laths with 1.20 mm thick top cover.

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters.

Exceeding 10.00 sqm and upto 16.80 sqm in the area.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness, jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Double charge vitrified tile polished finish of size

Size of Tile 600 x 600 mm

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:6 (1 cement: 6 fine sand)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two coats.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-charge.

With cement mortar 1:4 (1 cement : 4 fine sand).

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately).

Providing and fixing mineral fibre false ceiling at all heights with tiles of size 595X595mm of approved texture, design and pattern. The tiles should have minimum Humidity Resistance (RH) of 99%, minimum Light Reflectance = 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of minimum 0.30 mm thick (minimum galvanized @120 gsm) having rotary stitched double webbed white with 6mm reveal Silhouette profile (white/black) comprising of main T runners of minimum 15x38 mm of length 3000 mm, cross T of size minimum 15x38mm of length 1200 mm and secondary intermediate cross T of size minimum 15x38 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (minimum galvanised @ 80 gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm,

spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size minimum 24x24X3000 mm made of minimum 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the Engineer-in charge.

With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC minimum 0.55 to 0.60)

Providing and fixing 12mm thick frameless toughened glass partition of approved brand and manufacturer i/c providing and fixing necessary SS patch fittings of approved size and make at top and bottom ends edges, to fix ceiling, floor and side walls as per sound engineering practice/ manufacturer specifications and making the necessary holes etc all complete as per the architectural drawings and the directions of engineer-in-charge .(Frameless door shutters with fittings shall be paid separately)

Providing and fixing Mortise lock of DORMA XL -C -2017 width 20mm, lock center to center 72mm with lock back end 55mm of satin stainless steel finish, hook lock or equivalent necessary accessories and screws etc all complete as per the directions of the Engineer-in-charge.

Providing and fixing brush finished stainless patch fittings of DORMA make or equivalent quality of approved make with necessary accessories and screws etc all complete as per the directions of the Engineer-in-charge.

Door handles of DORMA AIDO 'H' TYPE HANDLE XL-C (Model 3000A) of Grade SS-304 or Godrej of satin stainless steel finish or equivalent of length 300mm.

Door Stopper

Dismantling of aluminium partitions, doors, windows, including dismembering , proper numbering, stacking and placing all the serviceable material at the designated location at site of work and disposal off unserviceable material all complete as directed by the Engineer-in-charge. (Area of partition being dismantled shall be measured for payment)

Making and fixing of aluminum partitions in position including sorting available material of aluminum sections, particle boards, and snap on beading as per the approved drawing including fixing with rawl plugs, screws etc and filling of gaps if any at junctions with wall with sealant wherever required all complete as per the specifications and as per the directions of the Engineer-in-charge. Necessary screws, clamps, rawl plugs shall be arranged for fixing partitions . The available aluminium sections, boards, and snap on beading will be supplied by the department at no cost. Area of erected partition having board only shall be measured for payment.

Fixing of cash counter ( 01 No) of each size approximately 1.50 x 1.45 x 1.90 Mtrs which are available at adjacent ground floor of Max-I TE building in the site of the work(RLU building) at designated location by dismantling, shifting, stacking and refixing of cash counter including all leads, lifts and all other incidental charges all complete as directed by Engineer - in -charge. (Each cash counter fixed at designated location with all above operations is measured for payment)

Fixing of table top counter ( 02 Nos) of each size approximately 1.20 x 0.75 x 0.75 Mtrs which are available at adjacent ground floor of Max-I TE building in the site of the work(RLU building) at designated location by dismantling, shifting, stacking and refixing of table top counter including all leads, lifts and all other incidental charges all complete as directed by Engineer - in -charge. (Each table top counter at designated location with all above operations is measured for payment)

Fixing of L- shaped table top counter ( 01 No) of each size approximately 1.75 x 0.60 x 0.75 Mtrs which are available at adjacent ground floor of Max-I TE building in the site of the work(RLU building) at designated location by dismantling, shifting, stacking and refixing of table top counter including all leads, lifts and all other incidental charges all complete as directed by Engineer - in -charge. (Each L- shaped table top counter at designated location with all above operations is measured for payment)

Fixing of writing ledge ( 01 No ) of each size approximately 0.45 x 1.15 x 1.00 Mtrs which are available at adjacent ground floor of Max-I TE building in the site of the work(RLU building) at designated location by dismantling, shifting, stacking and refixing of table top counter including all leads, lifts and all other incidental charges all complete as directed by Engineer - in -charge. (Each writing ledge at designated location with all above operations is measured for payment)