Construction of 100 Beded Sabitribai Phule SC/ST Hostel (G+3) Building at Chapra in District Saran.

Building Construction Department

Bidder should fill in colored cells for Technical Evaluation per Requirements of SBD

Name of work : Construction of 100 Beded Sabitribai Phule SC/ST Hostel (G+3) Building at Chapra in District Saran.

53590135 Time of Completion in months AS PER CIRCULAR

Sl No. What to fill in Requirement Cl. No. of SBD FILL COLOUR CELL BELOW

Name of the contractor

Address of the contractor

Unconditional bank guarantee from any scheduled Indian bank issued within the state in the format given.

Total Bid Security Amount in Rupees 1072000 IFB

2 (i) Legal Status of Bidder (select from drop down list) 4.3(a)

(ii) Place of Registration. (select from drop down list)

(iii) write Principal place of Business

(iv) Power of attorney of signatory Bid (select from drop down list) 4.2(iv)

3 Total value of civil engineering construction work, in Rupees, Performed in last five years. minimum annual financial turnover (in all classes of civil engineering construction works only) amount of construction work of at least the equal to the 50 % of estimated cost of works for which bid has been invited. The turn over will be indexed at the rate of 8% for a year 26795067 4.5(A) (a)

Escalation Factor= 1.21

Escalation Factor= 1.21

Escalation Factor= 1.21

Escalation Factor= 1.1 0

4 Amout in Rupees related to Work Experience of Similar nature Satisfactory completed at least one similar work of value not less than 50% of estimated Cost 4.5(A) (b)

5 Minimum Quantities of work done as prime contractor in any one year during last five years, units shall be same as in Requirement column Items Qty Unit 4.5A( c)

BRICK WORK 274.02 cum

PCC / RCC 579.84 cum

Stone and Tiles Work: 0.000 Sqm

P.H.E Works 6.24 Rs in Lac

Electrical Work 28.46 Rs in Lac

fire fighting 5 Rs in Lac

furniture 13.86 Rs in Lac

6 Bidding Capacity: PLUMBING WORKS 31.14 Rs in Lac 4.7

40391721 DISQUALIFY

6 Electrical License The contractor or his identified sub-contractor should possess required valid electrical license for executing the building electrification works and should have executed similar electrical works for a minimum amount as indicated in Appendix in any one year 4.5A( d)

7 (a) Amount of Existing commitments and ongoing works in Rupees Sec 2-1.4(A)

(b) Amount of Work for which Bid already submitted, in Rupees Sec 2-1.4(B)

8 Numbers and Maximum age of Equipments with bidder Type of Equipment Nos. Maxm. Age Sec 2-1.5 [Reference Cl. 4.5 (B) (a)] Nos. Max. Age

Concrete Mixer with Integral weigh Batching facility 1

Pump for concreting 0

Transit Mixture 0

Steel shuttering 2000Sft 5

Vibrator (Plate & Niddle) 2

9 Name of the Personnel and Experince in years and Select from drop down list Personnel / Qualification 4.5(B) (b) Name of the Personnel and Experince in years

Project Manager (B.E. Civil + 10 Years Exp. (5 years as Manager having MBA) or equivalent or retired E.E.) 0

Site Engineer (B.E. (Civil) + 03 Years Exp. (3 years in Building Construction) or Diploma in Civil + 7 year Exp. In Building construction or retired A.E.) 01 No.

Plant Engineer (B.E. Mech./ Civil + 03 Years Exp. or Dip. Mech + 05 Years Exp. or Retired J.E.) 0

Quantity Surveyor (B.E. Civil + 03 Years Exp. or Dip. Civil + 05 Years Exp.) 0

Site Supervisor (Fresh Graduate in Civil or Diploma Civil + 02 Years Exp. or retired I.T.I Holder.) 01No.

10 Evidence of accesses to Financial Resources in Rupees Evidence of access to or availability of creadit facilities (10% of estimated cost), certified by bankers (for work under this bid). 4.2(i)

11 Proposed methodology and programme of construction Select from drop down list the proposed methodology and programme of construction, backed with equipment planning and deployment 4.3(l)

12 Litigation History. Select from drop down list. Information regarding any litigation, current or during the last five years, in which the Bidder is involved, the parties concerned, and disputed amount. (Attached or not) 4.3(j)

13 Affidavit Select from drop down list. Regarding statements made in the required attachments are true and correct. Sec-2, Affidavit

14 Undertaking Select from drop down list. Able to invest a minimum of cost upto 25% of contract value of work. During implementation of contract. Sec-2, Undertaking

15 Time of Completion in months As per circular 12 month

16 Registration No. 12 month

18 Labour License

19 Character Certificate

20 NOC for Debar (If required)

QUALIFICATION INFORMATION

The information to be filled in by the Bidder in the following coloured cells, will be used for purposes of post qualification as provided for in Clause 4 of the Instructions to Bidders. This information will not be incorporated in the Contract.

NAME OF THE CONTRACTOR

1 For Individual Bidders

1.1 Constitution or legal status of Bidder (Attach copy)

Place of registration :

Principal place of business :

Power of attorney of signatory of Bid (Attach)

1.2 Total value of Civil Engineering construction work performed in the last five years (Rs in.Lac) {Immediately preceeding the financial year in which bids are received and attach Certificate from Chartered Accountant) 2020_____ 2021_____

1.3.1 Work performed as prime contractor, work performed in the past as a nominated sub- contractor will also be considered provided the sub-contract involved execution of all main items of work described in the bid document, provided further that all other qualification criteria are satisfied (in the same name) on works of a similar nature over the last five years.**

NAME OF THE CONTRACTOR

Project Name Name of the Employer* Description of work Contract No. Value of Contract (Rs. In Crore) Date of issue of work order Stipulated period of completion Actual date of completion* Remarks explaining reasons for delay & work completed)

* Attach certificate(s) from the Engineer(s)-in-Charge

** Immediately preceding the financial year in which bids are received.

1.3.2 Quantities of work executed as prime contractor, work performed in the past as a nominated sub-contractor will also be considered provided the sub-contract involved execution of all main items of work described in the bid document, provided further that all other qualification criteria are satisfied (in the same name and style) in the last five years :**

NAME OF THE CONTRACTOR

Year Name of the work Name of the Employer* Quantity of work performed (cum) @ Remarks

Cement Concrete (including RCC & PCC) Masonry Earth works Remarks* (indicate contract Ref)

** Immediately preceding the financial year in which bids are received.

@ The item of work for which data is requested should tally with that specified in ITB clause 4.5A ©

1.4 Information on Bid Capacity (works for which bids have been submitted and works which are yet to be completed) as on the date of this bid.

(A) Existing commitments and on-going works:

NAME OF THE CONTRACTOR

Description of works Place & State Contract No. Name & Address of Employer Value of Contract (Rs Cr) Stipulated Period of Completion Value of works* remaining to be completed (Rs Cr) Anticipated date of completion

NOTE: * Attach certificate(s) from the Engineer(s)-in-Charge

(B) Works for which bids already submitted :

Description of works Place & State Name & Address of Employer Estimated value of works (Rs Cr) Stipulated period of completion Date when decision is expected Remarks, if any

1.5 Availability of key items of Contractor’s Equipment essential for carrying out the Works [Ref. Clause 4.5(B)(a)]. The Bidder should list all the information requested below. Refer also to Sub Clause 4.3 (d) of the Instruction to Bidders.

NAME OF THE CONTRACTOR

Description of works Requirement Availability proposals Remarks (from whom to be purchased)

No. Capacity Owned/Leased to be procured Nos./Capacity Age/ Condition

1.6 Qualifications and experience of key personnel required for administration and execution of the Contract [Ref. Clause 4.5(B)(b)]. Attach biographical data. Refer also to Sub Clause 4.3 (e) of instructions to Bidders and concerned clause of the Conditions of Contract.

NAME OF THE CONTRACTOR

Position Name Qualification Year of Experience (General) Years of experience in the proposed position

1.7 Proposed sub-contracts and firms involved. [Refer ITB Clause 4.3(k)]

NAME OF THE CONTRACTOR

Sanction of the works Value of Sub-contract Sub-contractor (Name & Address) Experience in similar work

Attach copies of certificates on possession of valid license for executing water supply/ sanitary work/ building electrification works/ Fire Fighting Works [Reference Clause 4.5(d) & Clause 4.5(e)]

*1.8 Financial reports for the last five years: balance sheets, profit and loss statements, auditors' reports (in case of companies/corporation), etc. List them below and attach copies.

1.9 Evidence of access to financial resources to meet the qualification requirements: cash in hand, lines of credit, etc. List them below and attach copies of support documents.

1.10 Name, address and telephone, telex and fax numbers of the Bidders' bankers who may provide references if contacted by the Employer.

* Delete if prequalification has been carried out

1.11 Information on litigation history in which the Bidder is involved.

NAME OF THE CONTRACTOR

Other Party(ies) Employer Cause of Dispute Amount involved Remarks showing Present Status

1.12 Statement of compliance under the requirements of Sub Clause 3.2 of the instructions to Bidders. (Name of Consultant engaged for project preparation is ** Arc N Design, Lucknow)

1.13 Proposed work method and schedule. The Bidder should attach descriptions, drawings and charts as necessary to comply with the requirements of the Bidding documents. [Refer ITB Clause 4.1 & 4.3(1)]

1.15 Quality Assurance Programme

2 Additional Requirements

2.1 Bidders should provide any additional information required to fulfill the requirements of Clause 4 of the Instructions to the Bidders, if applicable.

(ii) Undertaking

*** (iii) Update of original prequalification application

*** (iv) Copy of original prequalification application

*** (v) Copy of prequalification letter

* Delete, if prequalification has been carried out.

** Fill the Name of Consultant.

*** Delete, if prequalification has not been carried out.

Check List for Submission Of Tender above 2.0 Cr and below 50.0 Cr.

Evaluation will be done as per the information provided in the document attached with tender. Bidder may disqualified, if documents are not attached properly.

Name of the Bidder

Sl. No. Requirements Related document As Per SBD Document attached

1 REGISTRATION Any Contractor Registered with Central Government/Any State Government/Any Public Sector Undertakings or an agency of National or Internatiional repute may tender, but Registration with Building Construction Department will be essential after issue of Letter of Acceptance.

2 ELECTRICAL REGISTARTION SELF REG OR SUB CONTACTORS AFFIDAVIT (CL 4.5A (d)

3 Legal Status Of Bidder INDIVIDUAL/PARTNERSHIP FIRM/ PVT LTD/PUBLIC LTD/ JOINT VANTURE

4 POWER OF ATTORNEY NAME OF AUTHORIZED PERSON TO SIGNE HOLDING POWER OF ATTORNEY IF ANY

5 Joint Venture >10 Cr. Document will be submitted as per RCD Letter No.8131 dated 24.7.2012

6 BID SECURITY (EMD) NSC/TD/FD/UNCONDITIONAL BANK GUARNTY(BG)/PLEDGE/ISSUED AFTER DATE OF TENDER (AS PER CLAUSE NO. 1 OF SBD)

7 COST OF BOQ ANY SCHEDULE INDIAN BANK/NATIONALISED BANK

8 PAN CARD ATTACH PAN CARD

9 GST REGISTRATION ATTACHED GST

10 LAST 5 YEARS ANNUAL TURN OVER BALANCE SHEET, PROFIT & LOSS AND AUDIT REPORT DULY AUDITED BY CA.

11 EXPERIENCE Of SIMILAR NATURE Of W0RKS i) NOT LESS THAN 50% OF ESTIMATED COST (ESCALATION AS PER APPENDIX TO ITB SN.-19 ii) The completion Certificate shall be issued by employer not below the rank of executive engineer or project manager. In case of Private client the completion crtificate and valuation of the project issued by employer should be certified by the retired executive engineer/Registered valuer of Nationlised Bank/Insurance Company/Income Tax Department.

12 (A)QUANTITY OF WORK- EARTH WORK,PILE WORK, (RCC/PCC, ,B/W ,FLOORING, PHE AND ELECTRICAL etc EXECUTED DURING LAST 5 YEARS).REQUIREMENT OF QUANTITY DEPENDS ON TYPE OF WORK AND USUALLY 50% OF QUANTITY MENTIONED IN BOQ. (B) In case of secialised job like Fire fighting, HVAC, IIFT ETC. QTY /AMOUNT AS INDICATED IN ANY ONE YEAR IN LAST FIVE YEAR (QUANTITY EXECUTED MUST BE SATISFIED BY CONCERN ENGINEER INCHARGE. In case of Private client the quantity executed will be issued by employer should be certifed by the retired executive engineer/Registered valuer of Nationalised Bank/Insurance Company/Income Tax Department. In case of specialised job like Fire fightinhg HVAC, Lift etc Sub contractor Vender may be allowed but the subcontractor/Vendor Nominated by prime Contractor should required amount/quantity of experience. Experience certificate of sub contractor .vendor must be attached.

13 AMOUNT OF EXISTING COMMITMENTS AND ON GOING WORKS ATTACH AS PER SEC 2--1.4(A) (Bidder must declare themselve their all existing commitment hiding fact be sufficient cause for rejection.)

14 AMOUNT OF WORK FOR ALREADY SUBMITTED ATTACH AS PER SEC 2--1.4(B)

15 BIDDING CAPACITY ( BC-AxNx3-B) SHOULD BE MORE THAN BID VALUE

16 PLANT and MACHINARIES AS PER SEC 2-1.5 MAX. AGE 5 YEARS ATTACHED OWNED VOUCHER /CASH MEMO/INVOICE AND AFFIDAVIT IN CASE OF LEASED/HIRE ON AND AFTER DATE OF TENDER (Refer Departmental letter no 5195 dt 11-6-2019

17 KEY PERSONNEL AS PER SEC 2-1.6 ATTACHED NECESSARY CERTIFICATE AND CURRENT AFFIDAVIT OF BOTH EMPLOYEE AND EMPLOYER ON AND AFTER DATE OF TENDER (Refer Departmental letter no 5195 dt 11-06-2019

18 BANKER'S CERTIFICATE FOR EVIDENCE OF ACCESS TO OR AVAILABILITY OF CREDIT FACILITIES CERTIFICATE ISSUED BY BANK AS PER PRESCRIBED FORMAT IN SEC-2 ON AND AFTER DATE OF TENDER (Refer Department letter no 5195 dt 11-6-2019

19 AFFIDAVIT ATTACH AFFIDAVIT AS PRESCRIBED IN SEC-2 ON AND AFTER DATE OF TENDER

20 UNDERTAKING ATTACH AS PRESCRIBED IN SEC-2

21 LITIGATION HISTORY ATTACH AFFIDAVIT AS PRESCRIBED IN SEC-2 ON AND AFTER DATE OF TENDER

22 NOC FOR DEBAR ATTACH SELF DECLARATION.

23 PROGRAMME Of CONSTRUCTION ATTACH DESCRIPTIONS , DRAWINGS AND CHARTS AS NECESSARY

IF YOU HAVE NOT BEEN DEBARED WRITE "NOT APPLICABLE" IN YOUR LETTER HEAD SCAN AND UPLOAD IN THE IN NOC FOR DEBAR LINK

Note:-Attachment should be self attested and should be attached as per above instruction, otherwise it may be rejected. In case of E-sign it is not required.

I, the undersigned, do hereby certify that all the statements made in the required attachments are true and correct.

BILL OF QUANTITY

Name of Work:- Construction of 100 Beded Sabitribai Phule SC/ST Hostel (G+3) Building at Chapra in District Saran.

S.NO. S.O.R. CODE ITEM DESCRIPTION QTY. UNIT RATE AMOUNT

PART-A CIVIL AND FINISHING WORK

1 2.29.1 Clearing jungle including uprooting of rank vegetation ,grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 1701.98 100 Sqm 697.40 11,870.00

2 Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

3 2.27 Extra for every additional lift of 1.5 m or part thereof:-

3.1 2.27.1 All kinds of soil. 323.13 Cum 49.40 15,963.00

4 2.17 Close timbering in case of shafts, wells, cesspits, mannoies and the like including strutting, shoring and packing cavities (wherever required) complete (Measurements to.be taken of the face area timbered):

4.1 2.17.2 Depth exceeding 1.5 m but not exceeding 3 m 97.54 Sqm 140.80 13,734.00

5 2.35 Supplying chemical emulsion in sealed containers including delivery as Supplying chemical emulsion in sealed containers including delivery as specified.

5.1 2.35.1 Chlorpyriphos /Lindone emulsifiable concentrate of 20% 841.18 Litr 200.90 168,993.00

6 2.37 Diluting and injecting chemical emulsion for POST CONSTRUCTIONAL anti- termites' treatrnent (including the cost of chemical emulsion)

6.1 2.37.1.1 Along external wall where the apron is not provided using With hlorpyriphos /Lindone E.C. 20% with 1% concentration chemical imulsion @ 7.5 liters / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete: With chlorpyriphos/Lindone E.C. 20% with 1% concentration 83.72 Rmt 39.90 3,340.00

7 2.37.2 Along the external wall below concrete or masonry apron using chemical emulsion @ 2.55 litres per linear metre including drilling and plugging holes etc.

7.1 2.37.2.1 With chlorpyriphos E.C. 20% with 1% concentration 83.72 Rmt 49.10 4,111.00

8 2.28 LOCAL SAND FILLING

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete. 842.85 Cum. 287.30 242,151.00

9 2.26 BACK FILLING WORK

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth: consolidating each deposited layer by ramming and watering lead 826.62 Cum 123.90 102,418.00

10 2.25(A) LOCAL EARTH FILLING

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead. 1170.24 Cum 411.70 481,788.00

11 11.72 100A BRICK FLAT SOLING

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l, 1283.43 Sqm 283.30 363,596.00

12 11.73 100A BRICK EDGE SOLING

Providing designation 100 A one brick on edge soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l, 633.89 Sqm 444.80 281,954.00

13 11.78 60MM CHAMFERED EDGE PAVER BLOCK.

Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size

/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding /laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer’s specifications & direction of Engineer-in-Charge. 60mm thick C.C.paver block of M-35 grade with approved colour, design & pattern. 133.83 Sqm 714.00 95,555.00

14 4.1 PLAIN CEMENT CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-all work up to plinth level.

14.1 4.1.3 with 1:2:4 (1 Cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 81.13 Cum 3,998.10 324,366.00

15 16.42 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete. 131.91 Cum 4,649.00 613,250.00

16 5 REINFORCED CEMENT CONCRETE WORK.

16 5.1 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering, finishing and reinforcement- All work puto plinth level

16.1 5.1.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20 mm nominal size) 65.77 Cum 4,688.30 308,349.00

17 5.2 Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement.

17.1 5.2.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone aggregate 20mm nominal size) 36.74 Cum 5,670.00 208,316.00

18 5.33 RCC WORK UP TO PLINTH.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cementcontent as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and including retard setting of concrete, improve workability without impairing strength andadmixtures in recommended proportions as per IS: 9103 to accelerate, reinforcement, durability as per direction of Engineer-in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.

18.1 5.33.1 All works up to plinth level 420.750 Cum 5,063.40 2,130,426.00

18.2 5.33.2.1 All work above Plinth level upto floor V Level. 107.00 Cum 5,863.20 627,362.00

18.3 5.33.2 All work above Plinth level upto floor V Level. 316.37 Cum 5,863.20 1,854,941.00

19 5.9 SHUTTERING WORK

Centering and shuttering including strutting, propping etc. and removal of form for.

19.1 5.9.1 Foundations, footings, bases of columns etc. for mass concrete. 258.10 Sqm 211.60 54,614.00

19.2 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts 1073.20 Sqm 494.40 530,590.00

19.3 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 1393.70 Sqm 404.70 564,030.00

19.4 5.9.3 Suspended floors, roots, landings, balcnies and access platform. 1491.66 Sqm 437.50 652,601.00

19.5 5.9.7 Stairs,(excluding landings) except spiral-staircaces. 158.31 Sqm 439.90 69,641.00

20 5.22 REINFORCEMENT STEEL WORK

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

20.1 5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. 27919.08 Kg. 94.50 2,638,353.00

20.2 5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. 18562.94 Kg. 92.60 1,718,928.00

20.3 5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. 25663.83 Kg. 90.80 2,330,276.00

20.4 5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia 18574.44 Kg. 91.70 1,703,276.00

20.5 5.22.7E Thermo-Mechanically Treated bars TMT Fe-500-20mm dia. 24479.48 Kg. 91.70 2,244,768.00

20.6 5.22.7F Thermo-Mechanically Treated bars TMT Fe-500-25rnm dia. 18359.61 Kg. 91.70 1,683,576.00

21 10.18 M.S FAN CLAMP

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 90.00 Each 165.40 14,886.00

22 6.1A 100A BRICK WORK UP TO PLINTH

Brick work with bricks of class designation 100A in foundations and plinth in :

22.1 6.1.12/1 Cement mortar 1 .:4 (1 cement: 4 coarse sand ) 45.99 Cum 5,017.90 230,773.00

23 6.1C FLY ASH BRICK WORK UP TP PLINTH

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 infoundations and plinth in:-

23.1 6.1.12C Cement mortar 1.:4 (1 cement: 4 coarse sand ) 85.80 Cum 5,116.30 438,979.00

23.2 6.1.14C Cement mortar 1.:6 (1 cement: 6 coarse sand ) 66.08 Cum 4,923.00 325,312.00

24 6.1.14C & 6.3C FLY ASH BRICK WORK ABOVE PLINTH

Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : Cement mortar 1.:6 (1 cement: 6 coarse sand )Extra tor Brick work in superstructure above plinth level upto floor V cum 378.68 Cum 4,923.00 1,864,242.00

25.0 6.3C Extra tor Brick work in superstructure above plinth level upto floor Vcum 378.68 Cum 842.20 318,924.00

26.0 6.45 Half brick masonry with non modular fly ash bricks of class designation 10, conforming IS :12894, in superstructure above plinth and upto floor V level.

26.1 6.45.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand) 300.52 Sqm 700.80 210,604.00

27 Derived from 11.76 Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I. 14.41 Cum 3,466.96 49,959.00

28 13.24.2 CEILING PLASTER

Providing 6mm thick ceiling plaster in coarse sand mixed with 1:4 (1 cement: 4 coarse sand) 1430.38 Sqm 125.60 179,656.00

29 5.23A Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). 84.08 Sqm 127.20 10,695.00

30 13.11.4 INNER AND OUTER PLASTER

Providing 12mm thick cement plaster in coarse sand mixed with 1:6 (1 cement: 6 coarse sand) 3330.10 Sqm 141.50 471,209.00

31 13.12.4 EXTERNAL PLASTER

Providing 15 mm cement plaster on rough side of single or half brick wall of mix. 1:6 (1 cement: 6 coarse sand) 2375.78 Sqm 162.80 386,777.00

32 13.37 Extra for plastering exterior walls of height more than 10m form ground level for every additional height of 3.0 m or part there of 2347.23 Sqm 44.40 104,217.00

33 13.17.1 Providing 12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of neat cement 166.59 Sqm 203.60 33,918.00

34 R/A Providing and fixing rabbit wire mesh with nail at the joint before plastering require bending in shape and cutting………all complete job 476.72 Sqm 260.03 123,962.00

35 13.18 PLASTER WITH PUNNING

Providing 15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished with a floating coat of neat cement on the rough side of single or half brick wall. 340.83 Sqm 229.30 78,151.00

36 13.116 Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge. 476.00 Rmt 47.10 22,420.00

37 22.14 Grading roof for water proofing treatment with

37.1 22.14.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) 20.42 Cum 3,990.30 81,482.00

38 22.3 TOILET AND KITCHEN WATERPROOFING

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). 114.65 Sqm 480.60 55,101.00

39 22.20.1 TERRACE WATERPROOFING

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/ sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat

the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5 cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane. 3 mm thick. 499.31 Sqm 472.50 235,923.00

40 11.36 CERAMIC GLAZED WALL TILES

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green , black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete 410.13 Sqm 795.00 326,052.00

41 11.37 CERAMIC GLAZED FLOOR TILES

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete. 116.07 Sqm 686.80 79,717.00

42 11.41 VITRIFIED FLOOR TILES

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to

IS: 15622 of approved make in allcolours and shades, laid on 20 mm thick cement mortar 1:4 (1cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

43 11.20 22MM THK. CHEQUERRED TILES

Chequerred precast cement concrete tiles 22 mm thick with marbie chips of size 6 mm in footpath & coutyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning tec. Complete on 20 mm thick bed of cement mortar 1:4(1 cement:4 coarse sand)

43.1 11.20.1 Light shade using white cement 242.07 Sqm 1,053.60 255,045.00

44 11.23 Marble stone flooring with 18 mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with:

44.1 11.23.2.1 Rajnagar plain white marble 18mm thick above 0.20 sqm upto 0.50 sqm 555.83 Sqm 1,703.40 946,801.00

45 11.24 Extra for nosing in marble stone for treads 115.08 Sqm 310.60 35,744.00

46 11.25 Extra for marble stone flooring in treads steps and risers using single length up to 2.00m 115.08 Sqm 369.20 42,488.00

47 11.26 KOTA STONE IN IN FLOORING

Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . Base with 1:1:1 (1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand)

48 8.2 GRANITE STONE IN KITCHEN COUNTER

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

48.1 8.2.1 Rajnagar plain white marble /Udaipur green marble/ Zebra block marble

8.2.1.1 Area of slab upto 0.50 sqm 18.34 Sqm 2,458.00 45,080.00

49 8.3 EDGE MOULDING WORK

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in- Charge.

50 8.4 Extra for fixing marble/granite stone over and above coresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc. complete. 27.03 Rmt 279.40 7,552.00

51 8.5 OPENING IN COUNTER STONE

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform. Vanity counters and similar location in marble/ granite/ stone work including necessary holes for pillar taps etc. including rubbing, moulding and polishing of cut edges etc. complete. 19.00 Each 428.20 8,136.00

52 10.15 M.S C-PROFILE DOOR FRAME

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by . mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre- treatment of the surface as directed by Engineer-in-charge:

53 10.3 M.S COLLAPSIBLE GATE

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots. nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Collapsible Gate CG (10'-2" x 8'-6") 26.56 Sqm 6,303.40 167,418.00

54 9.48 M.S GRILL AND STAIR RAILING

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all

54.1 9.48.1 Fixed to steel windows by welding 15.00 Kg 144.50 2,168.00

54.2 9.48.2 Fixed to openings/ wooden frames with rawl plugs screws etc. 7843.67 Kg 161.10 1,263,615.00

55 10.36 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.). 530.78 Kg 546.80 290,231.00

56 10.33 M.S PIPE HAND RAIL

Providing and fixing bright finished brass welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer.

56.1 10.33.1 MS tube (medium) 40mm nominal bore 69.34 Kg 121.90 8,453.00

57 12.47 Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.

57.1 12.47.1 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified 13.73 Sqm 1,097.90 15,074.00

58 9.147D Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

58.1 9.147D.3 Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm). 187.250 Sqm 7,261.90 1,359,791.00

58.2 9.147D.1 Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) 32.72 Sqm 7,074.90 231,491.00

59 10.12.1 STEEL GLAZED WINDOW

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs 10 cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer; excluding the cost of metal beading and other fitting except necessary. hinges or pivots as required. 1.12 Sqm 3,038.90 3,404.00

60 10.13B Extra for providing and fixing steel beading of approved shape and section with screws instread of glaxing clips and met. Sash putty in steel doors, windows, Ventilators and comosite units. 1.12 Sqm 396.70 444.00

61 9.20 FLUSH DOOR SHUTTER

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

61.1 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 90.85 Sqm 2,845.60 258,523.00

62 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured) 90.85 Sqm 401.40 36,467.00

63 9.26 Extra for cutting rebate in flush door shutters (total area of the shutter to be measured) 3.64 Sqm 93.70 341.00

64 21 ALUMINIUM FRAME WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)

64.1 21.1.2.1 Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) 128.29 Kg 447.20 57,371.00

65 21.2 PRELAMINATED PARTICLE BOARD

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge

65.1 21.2.1 Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side 4.29 Sqm 841.00 3,608.00

66 21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

66.1 21.3.2 With float glass panes of 5.50 mm thickness(weight not less than 12.50 kg/sqm) 4.96 Sqm 1,115.10 5,531.00

67.0 21.4 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete asper the direction of Engineer-in-charge.

67.1 21.4.2 With brass cover plate minimum 1.25 mm thickness 2.00 Each 2,444.30 4,889.00

68.0 26.86 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door /window/ Ceosetory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm, modulus of elasticity 900 N/mm and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for Separately).

69.0 26.88 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers {wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm', modulus of elasticity 850 N/mm' and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk 5.5 screws, all as per direction of Engineer-In- Charge. {Note: stainless steel butt hinges and necessary 5.5 screws shall be paid separately)

70.0 9.96 DOOR SLIDING BOLT.

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

71.0 9.97 DOOR TOWER BOLT

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete:

72 9.100 DOOR HANDLE

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

73 21.12 Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer-in-Charge.

73.1 21.12.3 Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar 4.00 Each 608.40 2,434.00

74 9.101 HANGING FLOOR DOOR STOPPER

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

74.1 9.101.2 Twin rubber stopper 45.00 Each 60.80 2,736.00

75 9.83 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 2.00 Each 979.50 1,959.00

76 10.5 Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners. all necessary fittings complete including applying a priming coat of approved steel primer.

76.1 10.5.2 Using flats 30x6 mm for diagonal braces and central cross piece. 4.49 Sqm 3,467.90 15,571.00

77 13.80 A.2 WHITE CEMENT PUTTY

Providing and applying white cement based putty of average thickness 2.0 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 4350.35 Sqm 105.40 458,527.00

78 13.79 WATERPROOFING CEMENT PAINT

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

78.1 13.79.1 New work (three or more coats) 1437.08 Sqm 81.20 116,691.00

79 13.78 APPLYING PRIMER

Applying one coat of cement primer of approved brand and manufacture on wall surface:

80 13.79 Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

80.1 13.79.1 New work (three or more coats) 938.70 Sqm 81.20 76,222.00

81 13.77 INTERNAL WALL AND CEILING PAINT

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

81.1 13.77.2 New work (two or more coats ) over and including priming coat with cement primer 4350.35 Sqm 102.30 445,041.00

82 13.81.3 APPLYING STEEL PRIMER

Applying primer coat with ready mixed zinc chromate yellow primer of approved brand and manufactured on steel galvanised steel/iron work 646.79 Sqm 34.60 22,379.00

83 13.93 SYNTHETIC ENAMEL PAINT FOR STEEL

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

83.1 13.93.1 New steel work (two or more coats) 646.79 Sqm 84.50 54,654.00

84 13.94 SYNTHETIC ENAMEL PAINT

Painting with synthetic enamel paint of approved brand and manufactured of required colour to give an even shad

Two or more on new work over an under coat of suitableshade with ordinary paint of aproved brand and manufacture 257.11 Sqm 116.50 29,953.00

85 6.47A 250MM WIDE DRAIN

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l, 72.17 Rmt 1,087.90 78,514.00

86 0362 Supplying brick bat for filling in recharge pit etc all complete job. 11.04 Cum 1,307.47 14,434.00

PART-B PUBLIC HEALTH ENGINEERING WORK

87 17.1 Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete,including cutting and making good the walls andlevel white P.V.C.flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floorswherever required :

87.1 17.1.1 White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests 9.00 Each 4,470.90 40,238.00

88 17.2 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required

88.1 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid 11.00 Each 4,230.00 46,530.00

89 17.10. Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :

89.1 17.10.2.1 Kitchen sink without drain board 610x510 mm bowl depth 200 mm 3.00 Each 3,786.60 11,360.00

90 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 8.00 Each 1,068.50 8,548.00

91 17.33 Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. 8.00 Each 713.30 5,706.00

92 12.78 Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

93 12.79. Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

93.3 12.79.3.1 75mm dia S/T with door 2.00 Each 141.60 283.00

93.5 12.79.4.1 75mm dia S/T without door 6.00 Each 124.20 745.00

93.6 12.79.4.2 110mm dia S/T without door 46.00 Each 190.70 8,772.00

94.0 12.80 Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete

95.0 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require 22.00 Each 2,764.40 60,817.00

96.0 18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 22.00 Each 96.80 2,130.00

97.0 18.22.2 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter 14.00 Each 190.10 2,661.00

98.0 17.37 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),including cost of cutting holes and making good the walls etc. :

98.1 17.37.1 For 100 mm diameter pipe 22.00 Each 178.50 3,927.00

99.0 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

99.1 18.7.2 20 mm dia nominal bore 182.77 Rmt 233.90 42,750.00

99.2 18.7.3 25 mm dia nominal bore 96.76 Rmt 317.30 30,702.00

100.0 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

100.1 18.8.1 15 mm dia outer nominal bore 91.45 Rmt 278.20 25,441.00

101.0 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

101.1 18.17.1 25 mm dia nominal bore 4.00 Each 532.30 2,129.00

102.0 18.19 Providing and fixing gun metal non return valve of approved quality (screwed end) :

102.1 18.19.1.1 25 mm nominal bore (Horizontal) 4.00 Each 506.60 2,026.00

103.0 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 16000.00 Liter 9.70 155,200.00

104.0 18.76.1 Cutting holes up to 30x30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular) bricks 28.00 Each 198.50 5,558.00

105.0 18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 33.00 Each 217.10 7,164.00

106.0 18.78 Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. 188.21 Rmt 85.40 16,073.00

107.0 18.21 Providing and fixing uplasticised PVC connection pipe with brass ions :

107.1 18.21.2 45 cm length

107.2 18.21.2.2 15mm dia nominal bore 30.00 Each 102.60 3,078.00

108.0 18.58 Providing and fixing PTMT grating of approved quality and colour.

108.1 18.58.2 Rectangular type with openable circular lid

108.2 18.58.2.1 150 mm nominal size square 100 mm diameter of the inner hinged round grating 15.00 Each 169.70 2,546.00

109.0 17.73 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

109.1 17.73.1 450 mm long towel rail with total length of 495 mm,78 mm wide and effective height of 88 mm, weighing not less than 170 gms 7.00 Each 397.30 2,781.00

110.0 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

110.1 17.28.2 Fexible Pipe

111.0 18.56.2 Providing and fixing C.P. brass Pillar Cock 25.00 Each 194.20 4,855.00

112.0 18.50.1 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 5.00 Each 715.10 3,576.00

113.0 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 35.00 Each 434.20 15,197.00

114.0 18.52.1 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 35.00 Each 594.80 20,818.00

115.0 19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

116.0 18.33. Constructing brick masonry road gully chamber 45x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design

116.1 18.33.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 12.00 Each 7,210.60 86,527.00

117.0 18.37 Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside)with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

117.1 18.37.1 With common burnt clay F.P.S.(non modular) bricks of class designation 100A 2.00 Each 6,849.90 13,700.00

118.0 18.36 Constructing masonry Chamber 60x60x75 cm, inside in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm top an 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand)12 mm thick, finished with a floating coat of neat cement complete as per standard design :

118.1 18.36.1 With common burnt clay F.P.S.(non modular) bricks of class designation 100A 1.00 Each 7,401.00 7,401.00

SUBMERSIBLE BORING

119.0 18.42 Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump / tube well is lowered and tested :

119.1 18.42.1 Up to 6 metres depth 6.00 Rmt. 350.60 2,104.00

119.2 18.42.2 Beyond 6 m and up to 12 m depth 6.00 Rmt. 416.10 2,497.00

119.3 18.42.3 Beyond 12 m and up to 18 m depth 89.00 Rmt. 484.10 43,085.00

120.0 24.3.1 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths,as per direction of Engineer -in-charge. 100 mm nominal size dia 90.45 Rmt. 546.10 49,395.00

121.0 24.4.4 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 50 mm nominal size dia 9.15 Rmt. 354.90 3,247.00

122.0 24.8 Gravel packing in tubewell construction in accordance with IS:4097 including providing gravel line/medium/coarse in required grading and sizes etc all complete job as per building specification & direction of E/I. 1.250 Cum. 1,343.20 1,679.00

123.0 24.13.1 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 100 mm dia 1.00 Each. 189.70 190.00

124.0 24.14.1 Providing and fixing mild steel clamp of required dia to the top of casinghousing pipe of tubewell 100mm dia etec. All complete job as per building specification & direction of E/I. 1.00 Each. 1,448.40 1,448.00

125.0 24.15.2 Providing and fixing bail plug/bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part-1) 100mm dia etec. All complete job as per building specification & direction of E/I. 1.00 Each. 228.30 228.00

126.0 18.9.4 Providing and fixing chlorinated Polyvinyl Chloride (CPVC) pipes havaing thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings etc all complete jobs. 54.09 Rmt. 359.10 19,424.00

127.0 24.12 Development of Submersible in accordance with IS:2800 (Part_1) and IS:1189 to establism maximum rate of usable water yield without sand content with required capacity air compressor running the compressor for required time as per direction of E/I etc all complete jobs. 6.00 hr 916.80 5,501.00

128.0 N.S S/F/F 1HP submersible motor ISI mark etc all complete jobs. 1.00 Each. 20,650.00 20,650.00

129.0 CARRIAGE OF MATERIALS

130 EXTRA COST OF MATERIALS

PART-C FIRE FIGHTING WORKS

131 I. PIPING & VALVES

7 Providing, laying, testing & commissioning of "C" Class heavy duty MS pipe conforming to IS 1239/3589 i/c fiiitngs like elbows, tees, flanges, tapers, nut bolts, gaskets, etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. Pipe Make : TATA/JINDAL HISSAR / NEZONE.

132 14 Providing, fixing, testing & commissioning of non-return valve of following sizes conforming to IS : 5312 complete with rubber gaskets, GI bolts, nuts, washers etc, as required. Make : Kartar / Audco / Advance / Sant.

133 11 Providing , fixing, testing & commissioning of butterfly valves of PN 1.6 rating with bronze / gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required, Make : Kartar / Audco / Advance / Sant.

133.1 11.4 80 mm dia. With lever 1.00 Each 4,588.00 4,588.00

II. INTERNAL HYDRANT SYSTEM

134 9.2 Providing and fixing ISI marked SS-304 fire hydrant valve 80 mm inlet with single outlet and fitted with 63 mm dia instantaneous female coupling on the outlet complete including companion flanges, pvc black cap and chain, nuts, bolts and 3 mm thick compressed asbestos gasket at locations as per drawings ( inlet flange as per IS: 5290-1969 Class C ). MAKE : OMEX / NEWTECH / SAFEGUARD/ EQV. 8.00 Each 5,722.00 45,776.00

135 17.1 Providing and fixing first aid fire hose reel drum wall mounting & swinging type fitted with 20 mm dia 30 m long high pressure hose as per IS : 5132 with 5 mm outlet SS nozzle with shut off valve ( IS: 884-1969). Make :OMEX / NEWTECH / SAFEGUARD / EQV. 8.00 Each 7,920.00 63,360.00

136 16.2 Providing and fixing 63 mm dia (15 m long) EPDM lined fabric hose including SS-304 male and female instantaneous type coupling approved by fire authority, machine wound with GI wire complete in all respects. Hose shall conform to IS : 636 Type II and coupling to IS: 903 – 1975 with ISI certification. MAKE : OMEX / NEWTECH / SAFEGUARD/EQV. 8.00 Each 4,445.00 35,560.00

137 18.2 Providing and fixing standard short size SS branch pipe with nozzle 16 mm dia. Outlet with standard instantaneous type 63 mm dia. Coupling as per IS : 903 ( ISI marked. ). MAKE : OMEX / NEWTECH / SAFEGUARD/EQV. 8.00 Each 1,631.00 13,048.00

138 15.2 Providing, installation, testing and commissioning of stainless steel 100 mm dia Ystrainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. MAKE : OMEX / NEWTECH / SAFEGUARD/EQV. 2.00 Each 6,048.00 12,096.00

139 19.3 Providing and fixing 150 mm dia Three –Way Fire brigade connection consisting of 63 mm dia instantaneously male coupling and and a check valve protected by cap scored with a chain glass bore etc. ( To be connected to riser ). MAKE : OMEX / NEWTECH / SAFEGUARD/EQV. 1.00 Each 9,071.00 9,071.00

III FIRE PUMPS & ACCESSORIES

140 1 Providing and fixing horizontal split casing single/multi stage, single/multi outlet pumping set with bronze impeller with C.I. body and connected by a flexible coupling to a totally enclosed fan cooled induction motor mounted on a common structural base plates with all pump accessories complete as per specifications including pressure gauges with gunmetal isolation valves and anti vibration pads, motor to be suitable for 415 volts, 3 phase, 50 cycles A.C. supply (Specifications as per fire fighting requirements and on the pattern of TAC or local authority approval) as per instruction and following specifications: MAKE : KIRLOSKAR/PEW/MATHER & PLATE/EQV.

140.1 4.2 Terrace Pump

Type : Split casing

Speed (rpm) : 2965

Capacity : 450 lpm

141 NS Providing and fixing fire hose cabinet fabricated from 16 gauge M.S. sheet with double glazed front door and pad locking arrangement, painted Fire Red with stove enameled paint and FIRE HOSE written on front including necessary supports ( to house ONE length of canvas hose with couplings, branch pipe and nozzle). MAKE : OMEX / NEWTECH / SAFEGUARD/EQV. 8.00 Each 7,600.00 60,800.00

142 NS Providing and fixing 25 mm dia brass ball valve full bore type with lever and screwed female ends. ( 20 kg./sq. cm.). ISI MARKED. 8.00 Each 1,722.00 13,776.00

143 NS Providing and fixing 25 mm dia gun metal single acting air release valve with screwed inlet tested for 20 kg. / cm². MAKE : OMEX / NEWTECH / SAFEGUARD/ EQV. 1.00 Each 1,722.00 1,722.00

144 NS Providing and fixing dial type pressure gauge with isolation cock and copper pipe on main header Dial diameter 100 mm celebration 0-14 / sq. Cm. MAKE : OMEX / NEWTECH / SAFEGUARD /HD/EQV. 8.00 Each 2,450.00 19,600.00

145 NS Providing and fixing of self illuminated “FIRE EXIT”, etc. signages. 4.00 Each 1,522.00 6,088.00

146 22 Providing and fixing dual type pressure switch suitable for 1-20 Kg/cm2 including electrical connections setting of Cut-In and cut-Off pressure complete in all respects. 2.00 Each 1,442.00 2,884.00

147 NS Providing and fixing heavy duty aluminium armored cables 1.1 KVA grade including necessary support clamps at ceiling

Power cable 3 core 16 Sq. mm 150.00 Rmt 456.00 68,400.00

IV FIRE EXTINGUISHERS

148 NS Providing and fixing CO2 extinguisher consisting of seamless MS cylindrical body squeeze lever discharge valve, internal discharge tube, 30 cms long high pressure discharge hose, discharge nozzle ISI marked as per IS: 15683 including fixing with dash fasteners etc. complete. MAKE : OMEX / NEWTECH/ SAFEGUARD/ EQV.

a) Capacity 4.5 kg. 8.00 Each 10,000.00 80,000.00

149 NS Providing and fixing stored pressure Multipurpose fire extinguisher consisting of welded M.S. cylindrical body, squeeze lever discharge valve, 30 cms long high pressure discharge hose ISI marked as per IS:15683 including fixing to wall with brackets etc. complete. MAKE : OMEX / NEWTECH/ SAFEGUARD/ EQV.

a) Capacity 6 Kg. 16.00 Each 4,500.00 72,000.00

V FIRE ALARM & DETECTION SYSTEM.

150 NS Supply, installation, testing and commissioning of conventional type Fire Alarm Control Panel 4 Zone capacity with LED display.

151 NS SITC of Optical type smoke detector complete with base. 35.00 Each 2,100.00 73,500.00

152 NS SITC of manual call point complete with mounting base. 6.00 Each 1,200.00 7,200.00

153 NS Supply and Installation of Wall Mounted Horn cum Strobe Lights with 110 cd. 7.00 Each 1,800.00 12,600.00

154 NS Supply and laying of 1.5 sq. mm dual core copper wire with 19 mm dia PVC conduit. 920.00 Rmt 125.00 115,000.00

PART-D FURNITURES SUPPLY WORK

155 NS Bed Dimension : 2000 x 900 x 650 mm (H) Structure is made up of 40 mm dia CRC tube with thickness 18 gauge. Horizontal base is made from steel sheet the thickness 14 gauge. Horizontal base will be stiffened with appropriate longitudinal 3 v shape sheet and lateral stiffeners 2 steel pipes with powder coating. The Product Should be Certified Company BIFMA, ISO-50001, Green Guard,Green PRO, Sedex, AIOTA, IGBC, AGSI, FSC & PEFC .(Size : 2000 x 900 x 650 mm (H) (Bed without Mattress) 102.00 Each 11,000.00 1,122,000.00

156 NS Mattress 2" thick (Size 75" x 36") Supplying and fixing of Mattress (size : 75"x36" x 2" thick) at site, with complete in all respect or as per direction of E/I 102.00 Each 4,400.00 448,800.00

157 NS Study Table & Chair Dimension : DESK - 600 W x 480 D x 750 H SEAT - 868 H x 500 W x S 450 Finish/Coating :-Powder Coating Material :-MILD STEEL TUBULAR SECTIO OVAL tube 5x15 Sq.tube 25x25 and PLB & Moulded wood,Total Weight : 23Kg,Available Base Frame :- Knock down, Features : -SEMI KNOCKDOWN ,11 TANK HOT ZINC PHOSPHATING PRE TREATMET PROCESS, Powder Coated.The Product Should be Certified Company BIFMA, ISO-50001, Green Guard, Green PRO, Sedex, AIOTA, IGBC, AGSI, FSC & PEFC. . As Per direction given by E/I. 102.00 Each 6,800.00 693,600.00

158 NS Steel Multifux system for Library S/F ct site Godrej/Durian steel Multifux system of size 7' x 36 " x 18" with 7 nos. shalves of galvanised steel sheet with M.S steel angle frame of size 40x40x8 mm. Complete with supplying and fixing at site with including painting etc.The Product Should be Certified Company BIFMA, ISO-50001, Green Guard, Griha, Green PRO, Sedex, AIOTA, IGBC, AGSI, FSC & PEFC. As Per direction given by E/I. 6.00 Each 9,200.00 55,200.00

159 NS 3 seator / Chrome chair 3 sector chair (Chrome):- Made of Cushion with high density cold cured self -skinned pre -molded foam of 50-60 density the shape of plywood. Upholstery is done by using high-pressure pneumatic spray glue and pneumatic press over crome base & legs etc.The Product Should be Certified Company BIFMA, ISO-50001, Green Guard, Griha, Green PRO, Sedex, AIOTA, IGBC, AGSI, FSC & PEFC. As Per direction given by E/I. 4.00 Each 10,620.00 42,480.00

160 NS Common room office / Office table Table for common room (Size : 1200 x 750 x 760) Supply, Fabrication & Installation of table made of Powder coated MS frame with 18mm thick Prelaminated board top complete in all respect with wire manager lockable drawer etc.all complete as per drawing .The Product Should be Certified Company BIFMA,ISO-50001, Green Guard,Griha, Green PRO, Sedex, AIOTA, IGBC, AGSI, FSC & PEFC. 4.00 Each 8,800.00 35,200.00

161 NS Dining Table Work Surface:- Dining Table made of Wood veneer/PLPB Board powder coated MS frame with 12mm thk glass top, 25mm Thick (±1mm) Base Material - 25mm MDF/PLPB Board on top PU painting of Minium 2H hardness with 75% glass as per color chart,combination color graphics on the centre. Color as per color chart. Brown laminate on bottom. Specially profiled edge orcomfort. Understructure: Bend pipe understructure of MS. Powder Coated. Pipe dia.38mm, 2mm thk. Understructure fitted with top by SS machine screws.Legs: MS Powder coated legs for PU top & SS legs for membrane top.38mm dia pipe legs are fixed with understurcture and table top.Ground Base - 2450mm (L) x 1175mm (W). Surface Top - 2400.8mm (L) x 1050.4mm (W) & Height - 750mm (H). The Product Should be Certified Company BIFMA, ISO-50001,Green Guard, Griha, Green PRO, Sedex, AIOTA, IGBC, AGSI, FSC & PEFC. As Per direction given by E/I 11.00 Each 25,429.00 279,719.00

162 NS Dining Chair Seat/Back: Stackable Café Chair: Size: (L)381mm X (D)419mm X (H)839mm Seat and back in PVC Moulded Chair with SS 202 grade frame Round Pipe. The Product Should be Certified Company BIFMA,ISO-50001, Green Guard /Green PRO, Sedex, AIOTA, IGBC, AGSI, FSC & PEFC.. The Product Should be Certified Company BIFMA, ISO-50001, Green Guard, Griha, Green PRO, Sedex, AIOTA, IGBC, AGSI, FSC & PEFC. 46.000 Each 1,800.00 82,800.00

163 NS Common Room chair Size :- Depth (D) - 57.0 cm, Width (W) - 58.0 cm Height (H) - 88.0 cm, Seat Height (SH) - 47.5 cm The seat & Back are made up of Cushion covered with rexine. Behind all this is a robust tubular framework that makes the chairs durable.The Product Should be Certified Company BIFMA, ISO-50001, Green Guard, Griha, Green PRO, Sedex, AIOTA, IGBC, AGSI, FSC & PEFC. 7.00 Each 1,800.00 12,600.00

TOTAL (PART-A, B, C & D) AMOUNT. 45,221,996.00

(I) TOTAL (Schedule & Non Schedule Item work). 45,221,996.00

(II) TOTAL (Non Schedule Item work). 3,362,235.00

(III) TOTAL (Schedule Item work). 41,859,761.00

(IV) Correction Factor @ 0.982 on Schedule Item work 41,106,285.00

(V) Add @ 5.36% of (iv) for Balance GST for Schedule Items 2,203,297.00

(VI) Add for 5 Year Operation, Maintenance & Repair Cost 1,227,118.00

TOTAL (II+IV+V+VI) 47,898,935.00

PART-E ELECTRIFICATION WORK

Part A - E.W & E.I

164 1.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.I. box etc as required.

Battten Holder 165

Down Lighter 201

Ceiling Fan 126

165 1.31 Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc. as required. 83 Each 414.00 34,362.00

166 1.32 Supplying and fixing suitable size of G.I. box with modular plate and cover in front or in surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch. connection, painting etc, as required. 23 Each 531.00 12,213.00

167 1.5 Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. 345 p. mtrs. 309.00 106,605.00

168 1.55 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required. 110 Each 632.00 69,520.00

169 1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 1700 p. mtrs. 201.00 341,700.00

1.7.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire(For St. Light) 130 p. mtrs. 201.00 26,130.00

1.7.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm (fpr 2 nos. of switch & Socket) 1650 p. mtrs. 246.00 405,900.00

1.7.4 2 X 6 sq. mm + 1 X 6 sq. mm (for SPN DB) For St. Light 5 p. mtrs. 422.00 2,110.00

1.7.11 4 X 6 sq. mm + 1 X 6 sq. mm earth wire (for TPN DB) 300 p. mtrs. 660.00 198,000.00

1.7.13 4 X 16 sq. mm + 1 X 6 sq. mm earth wire (for VTPN) 60 p. mtrs. 1,312.00 78,720.00

170 1.33 Supplying and fixing 2 pin, 6 amp. ceiling rose on the existing junction box/PVC box including connection etc as required. 327 Each 64.00 20,928.00

171 1.34 Supplying and fixing batten/angle holder including connection etc. as required. 165 Each 80.00 13,200.00

172 1.25 Supplying and fixing stepped type electronic Fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required. 126 Each 358.00 45,108.00

173 2.8 Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus-bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

2.8.5 6 way, Double door 1 Each 2,197.00 2,197.00

174 2.33 Supplying and fixing following ways, surface/recess mounting, Vertical three phase distribution board ( VTPN DB's ) of CRCA sheet steel, dust protected, duly powder painted suitable for upto 160 amp, four pole MCCB as Incomer and SP/TP MCB's as outgoing inclusive of tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's etc as required. (but without MCCB & MCBs)

2.33.2 6 way, Double door, I/C 160A, MCCB 4 Each 13,710.00 54,840.00

175 2.9 Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus - bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

2.9.1 4 way ( 4 + 12 ), Double door, horizontal type 19 Each 4,184.00 79,496.00

176 2.12 Supplying and fixing following rating, 240/415 volts, ‘C’ series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

2.12.1 6/32 amps, single pole 232 Each 237.00 54,984.00

177 2.13 Supplying and fixing following rating, 240/415 volts, ‘C’ series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

2.13.1 6/32 amps, double pole (On panel & DB for St. Light) 19 Each 667.00 12,673.00

2.13.4 40 A to 63 A, Four Pole (For TPN DB) 19 Each 2,324.00 44,156.00

178 2.4 Providing and fixing following rating and breaking capacity and pole MCCB with thrmomagnetic release and terminal spreaders in existing panel board including drilling holes in cubicle panel, making connections etc. as required.

179 2.7 Providing and fixing following capacity four pole ON-load/ panel mounted changeover switches inside the existing cubical panel board including drilling holes in cubicle panel, making connections etc. as required.

180 5.1 Supplying and fixing 4' X 18 watt LED batten with minimum efficacy 100 lm/w in polycarbonate housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required. 150 Each 521.00 78,150.00

181 5.8 Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

182 6.1 Supplying and fixing of following types lamp in the existing electrical fitting / fixtures etc. as required.

6.1.6 15 watt LED lamp 165 Each 250.00 41,250.00

183 8.11 Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.) 24 P. sqft. 1,809.00 43,416.00

184 A/R Supplying of copper strip of 50mm X5mm size for bus bar strip/interconnection including drilling holes etc. as required 10 P kg 871.00 8,710.00

185 8.13 Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required. 1 Each 6,536.00 6,536.00

186 7.9 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

187 3.6 Earthing with Copper earth Plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe 2.7 meter long etc. with charcoal/ coke and salt as required. 2 P. Set 13,721.00 27,442.00

188 3.17 Supplying & fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc as reqd. 30 P. mtr. 144.00 4,320.00

189 5.14 Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

191 8.5 Supplying and fixing of 32 mm dia X 1.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV/ HPSV/ LED street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required. 12 Each 1,038.00 12,456.00

192 7.7 Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

193 7.3 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required but excluding sand cushioning and protective covering.

7.3.3 Above 95 sq. mm and upto 185 sq. mm 75 Meter 143.00 10,725.00

194 DSR 9.2 Brush Less Direct Current (BLDC) Fan without Remote Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required.

DSR 9.2.3 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) 126 Each 2,695.00 339,570.00

195 8.17 Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

196 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required. 30 Each 34.00 1,020.00

PART B - LIGHTING ARRESTER

197 4.1 Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 3 mm thick copper baseplate includingholes etc.complete as required. 6 Each 1,056.00 6,336.00

198 4.4 Jointing copper/ G.I. tape ( with another copper/ G I tape, base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. as required. 30 Each 81.00 2,430.00

199 4.7 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run) 100 Meter 102.00 10,200.00

200 4.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run) 80 Meter 145.00 11,600.00

201 3.2 Earthing with G.I. earth plate 4.5 meter long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering watering pipe etc. with charcoal/ coke and salt as required. 6 P. Set 6,323.00 37,938.00

202 4.14 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. 30 Meter 174.00 5,220.00

Total 73,724.00

PART C - FOR SOLAR PHOT VALTAIC POWER GENERATION SYSTEM

203 DSR 17.1 Supplying Installation, Testing and Commissioning of on-grid Solar Photovoltaic Power Plant conforming to various applicable standards BIS, IEC, MNRE guidelines, the Central Electricity Authority Regulations and CPWD Specifications as amended up to date, consisting of Mono/Poly Crystalline silicon solar cells module, net metering facility, necessary control, protections, earthing, cabling, mounting structure, junction boxes, power conditioning units, Real time online web interfaced Data Monitoring System, Distribution panels, grid connecting arrangement, conduits, pipes, cable trays and other accessories etc. as required.

a) High Energy Efficiency Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730- Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 23% at STC with temperature coefficient of Pmax better than -0.30% per 0C. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. Solar Modules shall be designed to operate in relative humidity upto 100% with temperature between -10 0C and +85 0C. Further, each PV module used in any solar power project must have Radio frequency identification tag with information such as name of manufacturer, month and year of manufacturing, country of origin (separately for Solar cell and module), I-V curve, Unique Serial No and Model No of the module, Wattage, Im, Vm and FF, name of test lab issuing IEC certificate.

b)Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 415 V AC, three phase,4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC with a variation of 10% at nominal voltage. Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 0C, Minimum IP-65 for outdoor and Minimum IP 21 for indoor, Built-in meter and data logger, MPPT, switching devices IGBT/MOSFETs and controller Microprocessor /DSP. PCU/inverter shall be capable of complete automatic operation including wake-up, synchronization & shutdown. The PCU shall be able to withstand unbalanced load conforming to IEC standard with shutdown/standby mode. It must be provided with grid islanding along with manual disconnect pole isolation switch besides automatic disconnection. Minimum protections: Mains Under / Over Voltage, Over current, Over/Under grid frequency, Over temperature, Surge voltage induced at output due to external source, Short-circuit, Lightening, Anti Islanding (for grid synch. Mode) and other protections as per applicable standards. LCD/LED display of minimum parameters: DC input voltage, DC current, AC Voltage and current (all 3 phases, in case of 3 phase), Instantaneous & cumulative AC output power, Daily DC energy produced and other parameters applicable standard. Communication interface RS 485 / RS 232.

c) Module mounting structure: The roof top solar plant generation units shall be installed by using supporting Aluminium/Galvanized MS structure (mass of zinc coating shall be as per IS4759 ) having minimum head room clearance of 2.4 meter above the terrace level / ground level. The mounting structure would be designed to sustain wind load and seismic parameter of the site of installation. All the structure shall be design as per applicable BIS code and the material shall also confirm the applicable BIS Code. Structural material shall be corrosion resistant and electrolytically compatible with the materials used in the module frame, its fasteners, nuts and bolts. The suitable arrangements for maintenance and cleaning shall be provided.

d) Real time online web interfaced Data Monitoring System complete with accessories for various parameters such as Solar Irradiance, temperature, AC Output Voltage and current, Output Power, Power factor, DC Input Voltage and Current, Time Active, Time disabled, Time Idle, Power produced and other parameters as per standard practices.

e) Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and otheraccessories etc. as required. Each junction box shall be made of GRP/FRP/Powder Coated Aluminium /cast aluminium alloy with full dust, water & vermin proof arrangement with High quality Suitable capacity Meta OxideVaristors(MOVs) (semiconductor diode with resistant applied voltage)/ surge arrestors and suitable Reverse Blocking Diodes, isolation switches isolate the DC input to Inverter, copper bus bar etc.

f) Lightning, surge voltage protection, earthing protection and grid islanding.

g) Cables: Connections & Interconnections by required size IR/UV protected XLPE insulated copper conductor 1.1 kV grade armored power and control cables(ISI Marked) along with supplying & fixing of necessary channel/conduit, GI cable trays, supports, lugs, thimble and other accessories etc. as required.

h) DC Distribution Board And AC Distribution Panel Board: IP65, free standing, metal cladded, having copper bus bar, having required protection and control gears, connection-interconnection, etc. as required. Make Adani/Tata /Vikram Solar/Luminous/Kirloskar 12 Kwp 54,280.00 651,360.00

Total 651,360.00

PART D - FOR CCTV

204 DSR 40.11 Supplying Installation Testing and Commissioning of following Channel Network Video Recorder (NVR) with camera licenses to record for all channels having specifications and features etc as mentioned below

1) Network Video Recorder Embedded/ Installed OS (Linux) along with Camera Licenses to record per NVR and to provide a live view, storage and simultaneously Multi-channel playback of all IP camera or more and must be ONVIF with minimum support of 384 Mbps incoming Bandwidth.

2) NVR should support video compressions : H.265 or better, H.264, MJPEG.

3) Must support 1 channel RCA Input, 2 channel RCA Output for Two-way Talk with G.711U/A, G.711u, PCM, G726 audio compressions.

4) Intelligent auto power on when power resumes after power outage. 5) Storage: It should support minimum 8 SATA Slots with 20TB capacity/ Slot and RAID support of RAID 0/1/5/6/10.

6) Connectivity Interface : 2 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x RS232, 1x eSATA Port

7) Backup Interface : Its should have 4 Nosx USB port (2x USB3.0, 2xUSB2.0). 8) Video Output Ports: 2x HDMI and 2 VGA

9) Alarm Ports: It should have 16/8 Ch In/ Out ports to connect various type of external sensors and output devices like hooter/ Siren etc.

10) Email & SMS Altert options: Option for SMS/ Email Alerts to minimum 5 designated mobile number for power failure, HDD failure, vandalism, tempring, network disconnection and panic

11) Web & Mobile Application: Web, Mobile app ( For iPhone, iPad, Android Phone) for alerts and viewing.

12) Protocols: HTTP, HTTPS, TCP/IP, IPv4/IPv6, UDP, DHCP, DNS, SMTP, UPnP, IP Filter, PPPoE, FTP, DDNS, Alarm Server, IP Search, Multicast, Auto Registration, ONVIF (Profile T, Profile S, Profile G), CGI, SDK and OEM Cloud for remote monitoring without any public IP need.

13) Standards: CE, FCC, RoHS, BIS Certified 14) Power Supply : Should support AC100-240V, 50/60Hz Power supply.

15) Operating Condition : -5°C to 50°C, humidity 90% (max) (non-condensing) 16) The VMS application shall support all the features & functionalities of the offered cameras.

17) VMS should consist Licenses for all channels to record Cameras with General, motion detection, intelligent, alarm and POS recording modes. VMS should be provided with Camera Licenses , with no dependency of VMS licenses by binding with the MAC address of the cameras to achieve the functionality.

18) The NVR OEM shall be responsible for providing a mobile application compatible with both Android and iOS devices, enabling remote monitoring and playback of cameras/NVR footage.

19) The OEM must provide its own DDNS server hosted in India, eliminating the need for a public IP address for remote monitoring over the Internet.

20) Must support Continuous, Alarm, Motion, Instant, Panic Recording Mode. 21) It should support Resolution: 32MP; 24MP; 16MP; 12MP; 8MP; 5MP; 4MP; 1080p; 720p; D1; CIF; QCIF

22) When alarm recording is enabled and an event occurs, you can click the alarm icon on monitoring page to view the alert details. The snapshot function is supported on monitoring and playback page

23) The Network Video Recorder (NVR) shall be configured to send email whenever a system message is created or an alarm event occurs. The email server shall be a valid SMTP server. Each recipient email address shall be configured to receive any combination of critical, warning, or informational messages or alarm notifications. When an alarm occurs, the email message includes the NVR name, time of alarm and a list of camera that is configured to record upon alarm

24) It should have Web and GUI interface.

25) Built-In Artificial Intelligence: NVR should have built-in AI :- - 2 Channel face detection and recognition, - Minimum 4 Channel perimeter protection, - Minimum 8 Channel Smart Motion Detection

26) Face Recognition Database Capacity: It should support total Blacklist and Whitelist capacity of Minimum 20,000 Faces or more with Face Detection speed of 12 face images/sec and facility to add Name, gender, birthday, address, credential type, credential No., countries & regions and state to each face image.

27) Face & Human Attributes Search: Search Pictures/ Video by Gender, age group, glasses, expressions, face mask, beard, Top color, top type, hat, bag, age, gender and umbrella.

28) ANPR Capability: It should support ANPR Camera with License plate, plate color, vehicle body, vehicle model, vehicle logo, calling, seatbelt, vehicle registration location etc vehicle attributes.

29) Alarm Notifications based on: Motion detection, video tampering, video loss, scene changing, PIR alarm, Camera external alarm, Face detection, face recognition, perimeter protection (intrusion and tripwire), ANPR, people counting, stereo analysis, crowd distribution, heat map, Disk Full, Storage Error, IP Conflict and abnormal behavior of fan, cybersecurity exception

30) Alarm Notification should be linked with Recording, snapshots, Camera external alarm output, buzzer, logs, presets and email.

31) General AI Based Search: Search Pictures by channel, time, event type, target classification (Fall Detection, People Approach Detection, People No. Exception Detection, People Staying Detection, Violence Detection.

32) Smart playback function: Should support smart search for the selected area in the video and smart playback to improve the playback efficiency

33) VCA (Video Content Analytic): Should support multiple video contented analytics based on camera analytics

34) Analytics by NVR: Perimeter protection and face recognation

40.11.2 64 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9/16/25/36/64, 2nd screen: 1/4/8/9/16 1 Nos. 82,600.00 82,600.00

205 DSR 40.1 Supplying Installation Testing and Commissioning of 2 MP IP IR Dome Camera having following specifications, type of lens and features etc :-

1) Signal System: PAL/NTSC, Signal to Noise Ratio: >50 dB, Camera should display Camera title, Date & Time in live & recorded video

2)Image Sensor: 1/2.8" or better progressive Scan CMOS to get color image even at night condition(Minimum Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with IR or better) True Day & Night High Performance Mechanical IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt IR LED's with effective distance upto 50 meter or better and 30 meter for colour view in night, Imaging: 1/3s to 1/30000s electronic shutter support, Auto Gain Control , White Balance- Auto, Back Light ompensation, Multi zone Privacy Masking, HLC, Digital Watermarking.

3) Compression (Minimum):-Video:- H.265 or better, H.264H, H.264, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723

4) Wide Dynamic Range:- WDR (120db or more)

5) Digital Noise Reduction:- DNR (3D) On/Off

6) Video Streaming & Frame Rates :- Triple streaming , configurable (Main stream: 2MP (1920 ×1080)@25/30 fps,Sub streams minimum: 720P@25/30 fps).

7) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection

8) Cyber Security: AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs, account lockout, syslog, video encryption, IP/MAC filtering, HTTPS, trusted upgrade, trusted boot.

9) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot upto 512 GB. It should be supplied with minimum 128GB memory Card.

10) Recording Management: Format SD, overwrite, storage management, video to NAS device

11) Alarm Trigger : Motion/tampering detection; audio detection; network disconnection detection; IP conflict detection; memory card state detection; memory space detection

12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast

13) System Capability: ONVIF, Camera shall support open source VMS 14) Ethernet: 1 RJ 45 10/100 Ethernet port

15) Audio : It should support 1 x Built-In Mic and 1/1 Alarm In/ Out for External Mic. and Speakers as per site requirement.

16) Power Input: The camera should support simultaneous dual power input—12 VDC (via power adapter) and PoE (802.3af)—to ensure continuous operation in the event of a failure in one power source.

17) Power Requirement: 12VDC/24 VAC/PoE (802.3af)/ePoE 18) Housing/ Enclosure:- IP67 weather proof, IK10, Metallic body

19) Operating Condition:- Ambient Temperature:- (-) 05°C to 50°C, humidity 95% (max) (non-condensing)

20) IR life: 40000 hours or higher 21) Video Bit rate: 32 KBPS - 8 MBPS or better 22) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS

40.1.1 2MP (@ 25/30fps@1080P (1920×1080)) IP IR Dome Camera with 2.8/ 3.6mm fixed lens (25 for school, 35 for boy's hostel,35 for girl's hostel) 15 Nos 8,048.00 120,720.00

206 DSR 40.4 Supplying Installation Testing and Commissioning of4MP IP IR Outdoor Bullet Camera having following specifications and features etc :-

1) Signal System: PAL/NTSC, Signal to Noise Ratio: > 50 dB,Camera should display Camera title, Date & Time in live & recorded video

2)Image Sensor: 1/2.8" or better progressive Scan CMOS get color image even at night condition(Minimum Illumination: 0.006 Lux@ F1.4, AGC ON, 0 lux with IR or better) True Day & Night High Performance Mechanical IR cut filter with auto switch, Integrated IR Source (Auto, Manual)- Inbuilt IR LED's with effective distance upto 50 meter or better and 30 meter for colour view in night, Imaging: 1/3s to 1/30000s electronic shutter support, Auto Gain Control , White Balance- Auto, Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking.

3) Compression (Minimum): Video:- H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723 4) Wide Dynamic Range:- WDR (120dB or more) 5) Digital Noise Reduction:- DNR (3D) On/Off

6) Video Streaming & Frame Rates :- Triple streaming , configurable Main stream: 4MP (2560×1440)25/30fps Sub streams minimum: 720P@25/30 fps

7) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client software or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection

8) Cyber Security: AES 256-bit Encryption, Configuration encryption, trusted execution, Digest, security logs, account lockout, video encryption, IP/MAC filtering, HTTPS, trusted upgrade

9) Onboard Storage: Camera should support built-inm Micro SD/ SDHC/ SDXC Card slot upto 512 GB. Itshould be supplied with minimum 128GB memory Card.

10) Recording Management: Format SD, overwrite, storage management, video to NAS device, 11) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP conflict detection; memory card state detection; memory space detection

12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast,

13) System Capability: ONVIF, Camera shall support open source VMS 14) Ethernet: 1 RJ 45 10/100 Ethernet port. 15) Audio : It should support 1 x Built-In Mic and 1/1 Alarm In/ Out for External Mic. and Speakers as per site requirement.

16) Power Input: The camera should support simultaneous dual power input—12 VDC (via power adapter) and PoE (802.3af)—to ensure continuous operation in the event of a failure in one power source.

17) Power Requirement: 12VDC/24 VDC/PoE (802.3af)/ePoE 18) Housing/ Enclosure:- IP67 weather proof, IK10, Metallic body 19) Operating Condition:- Ambient Temperature:- (-)05°C to 50°C, humidity 95% (max) (non-condensing) 20) IR life: 40000 hours or higher 21) Video Bit rate: 32 KBPS - 8 MBPS or better 22) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS

40.4.1 4MP @ 25/30fps@1440P (2560 x 1440) Outdoor Bullet Camera with 2.8/ 3.6/6/8/12 mm fixed lens (as per site requirement) 8 Nos 10,063.00 80,504.00

40.4.2 4MP @ 25/30fps@1440P (2560x1440) Outdoor Bullet Camera with 2.7 to 4 mm ~12 to 13.5mm or better Varifocal Motorized lens. 2 Nos 23,754.00 47,508.00

207 NS 16- port Gigabit Unmanaged PoE switch (DS-3E0518P-E/M) Description- supply, installation, testing & Commissioning of Port POE Switch. 1 Nos 10,450.00 10,450.00

208 NS 8- port PoE switch with 2 Giga Uplink (CP-DNW GPU8G296) Description- supply, installation, testing & Commissioning of 8 Port POE Switch. 2 Nos 5,451.00 10,902.00

209 DSR 40.12 Supplying, Installation, Testing and Commissioning following capacity Serveillance grade Hard Disk with upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disk Speed, 3.5 inch form factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM, UKCA, VCCI, CB-Scheme, TUV, UL Certifications.

210 NS 6U DVR/Network Rack Description- supply, installation 6U Network Rack for Mounting NVR & POE Switch. 1 Nos 5,563.00 5,563.00

211 NS 2U DVR/Network Rack Description- supply, installation 2U Network Rack for Mounting NVR & POE Switch. 1 Nos 1,279.00 1,279.00

212 NS RJ 45 Connector Description- supply, installation, testing & Commissioning of RJ4 Connector for connection between CCTV Camera and POE Switch 100 Nos 25.00 2,500.00

213 NS Cat-6 PVC insulated and sheathed LAN cable. Description- supply and drawing UTP 4 Pair Cat-6 PVC Insulated and sheathed LAN cable through existing PVC conduit including connection, testing etc required. 1125 Nos 40.00 45,000.00

214 42.4 DSR Supplying, Installation, Testing and Commissioning of following size LED display (LED monitor) industrial grade with 3840x2160 resolution or better, USB playback, bluetooth and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nitsor better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing angle (H/V): 170°/ 170°, response time less than 12ms, Display control shall be on monitor screen and programmable with remote (remote shall be supplied with system), Key Board, Optical Mouse, etc. as required.

42.4.2 42 inch or larger 1 Each 51,459.00 51,459.00

215 26.1 DSR Online UPS - Input supply: Single Phase, Output Supply: Single Phase. Supplying, installation, Testing & Commissioning of following capacity at full load (Unity Power Factor) ON LINE Uninterrupted Power Supply (UPS) system suitable for Single Phase input, Single Phase output AC Supply. The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual bypass, suitable isolation transformer for additional protection against neutral faults etc. The UPS systems shall be Microprocessor based Digital Control, using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter with PWM (Pulse Width Modulation) Technology. The quality of design, manufacturing and inspection process should confirm to the relevant Inter-national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >95% at 100% non-linear loads. Current total harmonic istortion(ITHD)/ total demand distortion (TDD) on the input grid shall be < 5% at 100 %load. (The required LC filters shall be included in UPS cost), extreme power factor kit to be include to limit the input pf to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ) however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC single phase 160-270V 50 Hz and delivering output AC supply true sine wave single phase 220/230/240 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins and 150% for 1 minute. Operating temperature 0 to 40 0C, Relative humidity 0-95% non condensing, noise level less than 60db at 1 meter distance, Protection for Under voltage, over voltage, abnormal output voltage, battery over charging, output over current, short circuit, battery deep discharge , 10 KV surge. Display for watt/VA,Amp and Voltage power parameters etc. UPS shall comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent (VFI) type UPS (as per standard IEC 62040-1, 2 & 3) . The UPS should be with IGBT Based Inverter Technology, Communication RS232/ RS485/ SNMP port open protocol for BMS integration as per approved by Engineering in charge. Required battery racks, DC breaker of suitable rating and interconnecting copper conductor cable of suitable size and connectors and all required accessories are inclusive in the cost. The UPS should have QR code which should contain drawing, test report OEM manual, Geo- Tag of manufacturing location etc

Total 596,164.00

PART-E AUTOMATIC FIRE ALARM & DETECTION SYSTEM

216 DSR 28.2 Supply, Installation, Testing and Commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capabale of supporting not less than 240 devices ( including detectors) and minimum 120 detectors per loop and loop length upto 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230+_5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system(which is part of the scheduleof work under SH: PA system) and shall be complete with all accessories. The panel shall be compatible for IBMS system with open protocol BACnet/Modbus over IP complete as per specification.

DSR 28.2.1.2 Two Loop Panel. 1 Each 250,420.00 250,420.00

217 DSR 28.2.3 Supplying, installation, testing & commissioning of repeater panel with 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required. 2 Each 113,734.00 227,468.00

218 DSR 28.2.4 Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. 95 Each 3,004.00 285,380.00

219 DSR 28.2.5 Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. 20 Each 306.00 6,120.00

220 DSR 28.2.6 Supplying, installation, testing & commissioning of intelligent addressable programmable sounder complete as required. 8 Each 2,787.00 22,296.00

221 DSR 28.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as required 8 Each 3,434.00 27,472.00

222 DSR 28.2.10 Supplying, installation, testing & commissioning of addressable fire control module complete as required 8 Each 3,156.00 25,248.00

223 DSR 28.2.14 Supplying, installation, testing & commissioning of addressable manual call point complete as required. 8 Each 4,063.00 32,504.00

Total 876,908.00

Total Civil +Fire fighting+Furniture+Electrical) Work = 53,590,135.00

Executive Engineer,

Building Division,