Charipara to montali BSF camp

Amount

(Supply & Erection)

Supplying and Making Outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required up to 150 sqmm

Laying of one number PVC insulated and PVCsheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Trench Size: Width-350mm, Hieght- 1200 mm / Sand (couhioning): Hieght-250 mm, Width- 350mm / Protection: Double layer Bricks Upto 120 sq. mm

Laying of one number additional PVC insulated andPVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trenchin one tier horizontal formation including excavation,sand cushioning, protective covering and refilling the trench etc as required.Trench Size: Width-200 mm, Hieght-1200 mm / Sand (couhioning): Hieght-250mm, Width-200 mm / Protection: Double layer Bricks Upto 120 sq. mm

Manually digging /driIIing horizontally or diagonali direction for road crossing / Water supply line/Telcomunication line/Gas Pipe line etc. including Laying of 64 to 200mm dia GI pipe direct into the earth at a depth of minimum 1100mm below the ground surface with out effecting the existing road including excavation earth for entry pit as per site condition and direction of Engineering In Charge.

Erection of Stay set direct in earth complete with 19mm x 1800 mm long stay rod, anchor plate of size 300 x 300 x 8 mm ,thimble, turn buckle, 7/3.15 mm dia G.I Standed stay wire and stain insulator etc. with Supply of M.S.Clamp,Nuts & Bolts etc. as required and making complete in all respect.

Erection of M.S.Angle Cross-Arm,1.0 to 2.5 Mtr.Long 65 x65 x 6 mm ( Excluding the cost of BackClamp, Nuts & Bolts)

Erection of M.S.Channel Cross-Arm,1.3 to 2.8 Mtr.Long75 x40 x 40 x 6 mm ( Excluding the cost ofBack Clamp, Nuts & Bolts)

Erection of M.S.Channel Cross-Arm,0.6 to 2.8 Mtr.Long100 x50 x 50 x 6 mm (Excluding the cost ofBack Clamp, Nuts & Bolts)

Erection of 11KV Pin insulator along with Pin.

Erection of 11KV Single Disc insulator set along with necessary fittings

Febrication of Cross-Arms by MS Channel/MS Angle as per specification

Erection of 9KV,5KA single pole metal oxide gapless type LA , including necessary connection complete as per technical specification

Erection of 11KV DOF unit set of three nos including necessary connection complete as per technical specification. (Excluding the cost of back clamp, Nuts & Bolts)

Erection of 11KV 200 Amp. GOS unit set of three nos including necessary connection complete as per technical specification.(Excluding the cost of back cIamp,Nuts & Bolts)

Installation/Positioning of 11/0.430KV,3-Phase 100KVA of Distribution Transformer on Pole with necessary connections & fitting fixing of all allied accessories components as required for making complete in all respect for energizing

Erection of 9.0 mtrs length of PCC POLE at any kind of soil , including excavation of earth, refilling the pit with soil upto the ground level, ramming and making complete in all respect.

Carriage of G.O.S, D.O.F,L.A,etc., by Mechanical Transport from the Electrical Sub-Divisional Site Store to working site Vis-a-vis, including loading, unloading and stacking as required a) Upto the lead range 0-25KM From MMD Store to Sub Division Store

Carriage of 11/0.430, 3-Phase 100KVA by Mechanical Transport trom the Site /Store/Worshop to working site Vis-a-vis including loading, unloading and placing on base, as required,a) Upto the lead range 25KM From MMD Store to Sub Division Store

Laying of one number PVC insulated and PVCsheathed / XLPE power cable of 11 KV grade of all size in the GI Pipe/HDPE for riser including tieup ofPipe with pole by the help MS Flat Clamp (excludingcost of Clamp and Nut&Bolts) as required Up to 400 sq. mm

Supply of febricated clamps of assorted size of MS flat (50 x 6 mm) with double coat of red oxide primercoating

Supply of M.S.Nuts & Bolt i/c Washer of assorted size ISI Marked machine made

Providing of Pre-cast cement concretecableidentification route marker (1 cement: 2 coarse sand4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits as per design, drawing and specification of TSECL. The marker snail be embossed "DANGERS: TSECL, ELECTRIC POWER CABLE” with Black colour letter {both side) The visible part shall be painted with Yellow colour japan paint. (1 cement: 2 coarse sand 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits.

Earthing with G.I pipe 2.5mtr Long and 40 mm dia, including excavation, refilling with alternate layer of salt & Charcoal as per drawing including supply of G.I.Pipe, Salt & Charcoal, Gi wire, nuts &bolts, etc. as required.

Carriage of materials such as Cable,AAC, AAAC, ACSR, G.I,Wire,Cross-Arm,Stay set,lnsulators etc., by Mechanical Transport from the Electrical Sub- Divisional Site Store to working site Vis-a-vis, including loading, unloading and stacking as required, upto the lead of 25KM & 50KM.a) Upto the lead range 25KM From MMD Store to Sub Division Store

Supply of PCC Pole 9 m long

Supply of XLPE CABLE (HT) 3Cx120 sq. mm

Supply of 11KV G.O. Switch (3ph)

Supply of 11 KV D.O. Fuse unit (3ph)

Supply of M.S. ANGLE (65x65x6) mm Angle

Supply of M.S CHANNEL (75x40x40x6) mm Channel

Supply of M.S. CHANNEL(100x50x50x6) mm Channel

Supply of Aluminium Lugs 120 mm sq

Supply of HDPE Pipe PE100 grade 110 mm outer Dia.

Supply and installation of 1.5 ton 5 star speed slit type Inverter wall mounted green Air conditioner (multiple cooling mode) preferable Panasonis/LG / Daikin / Carrier.- ISEER Value: 4.5 to 5.05 W/W

12 mm cement plaster of mix Cement mortar 1:4 (1 cement : 4 fine sand)

20 mm cement plaster of mix : Cement mortar 1:4 (1 cement : 4 fine sand)

6 mm cement plaster of mix : Cement mortar 1:3 (1 cement : 3 fine sand)

Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats on new work.

Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : New work ( two or more coats) over and including water thinnable priming coat with cement primer.

Providing and applying cement slurry on old CC / RCC / Brick works in joints to receive new and fresh CC / RCC / Brick works including roughening and cleaning the old surface as required complete as per direction of the Engineer in charge.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with synthetic enamel paint ( one or more coats ) of required colour of approved brand and manufacture on old work to give an even shade including preparation of surface as required complete as per direction of the Engineer in charge.

Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge.

Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge.Double charged Stainfree vitrified tiles (Glossy) Size of tile 600 mm x 600 mm

First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete, In cement mortar 1:4 ( 1 cement : 4 fine sand )

Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete, In cement mortar 1:4 ( 1 cement : 4 fine sand ).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineer­in­charge. (Glazing and paneling and dash fasteners to be paid for separately), For fixed portion of approved quality,Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ),Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board grade-I, type II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P. brass / stainless steel screws all complete as per architectural drawing and the direction of Engineer-in-charge , Prelaminated particle board of approved quality with decorative lamination on one side and balancing lamination on other side.

Providing and fixing 12 mm thick prelaminated three layer medium density (exterior grade ) particle board grade-I, type II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P. brass / stainless steel screws all complete as per architectural drawing and the direction of Engineer-in-charge , Prelaminated particle board of approved quality with decorative lamination on one side and balancing lamination on other side.

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require , White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing ,Circular shape 450 mm dia.

Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion,Single socketed pipe - 110 mm OD

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: a) Coupler 110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: b) Single equal tee with door 110x110x110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: c) Bend 87.5° 110 mm

Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised - PVC soil, waste & vent pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc. complete,110 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge,Internal work - Exposed on wall a) 15 mm nominal outer dia .Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge,Internal work - Exposed on wall b) 25 mm nominal outer dia .Pipes.

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length, 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms, 15 mm nominal bore

SAJAL DAS (BID ID -183413)

KAJAL DAS (BID ID -183490)

RATAN PAUL (BID ID -182940)