Supply, Installation, Testing and Commissioning of Beautification and Electrification work for Bajrang Setu at Tapovan in District Tehri Garhwal.

Amount

Supply, installation, testing and commissioning of Minimum 260 nos or above Linear pixel LED profile light which shall be mounted on the both sides of suspension cables of the bridge. The Aluminium extrusion housing of the profile shall be customized as per the design of the suspenders of the bridge to achieve the illumination on the both sides of the bridge. Each LED pixel shall be RGBW individually controlled to achieve the dynamic/animated media effects.The pixel length shall be 100 -125mm, 1.8-2W per pixel controlled by SPI/DMX 512protocol. The fixture shall be addressable with 10 channels per meter. All the fixtures shall be mounted back to back and continuously for view on both the sides of the suspenders with the help of IP68 connectors. The fixtures lengths should be customized depending on the lengths of the bridge suspenders having the power consumption as 18-20W/mtr. The fixture should have atleast 300 luminous flux. Maximum width of channel up to 55 mm. The desired content on the The product shall be IP67 protected and IK08 rated against any impacts. Input Voltage - 24V DC. Length -1000mm. LED Make - Cree, Nichea, Osram, Lumiled. Installation charges Including rent of use T&P with operator and Skilled labour and cost of 03 nos steel Tie per Linear Pixel LED Light.as per direction by engineer in charge and Complete in all respect. as per Technical Specification. [Suspension Cable (from First Suspender to sr no 13th Suspender on inner & outer side ) ]

Supply, installation, testing and commissioning of Minimum 72 nos or above Linear pixel LED profile light which shall be mounted on the both sides of suspension cables of the bridge. The Aluminium extrusion housing of the profile shall be customized as per the design of the suspenders of the bridge to achieve the illumination on the both sides of the bridge. Each LED pixel shall be RGBW individually controlled to achieve the dynamic/animated media effects. The pixel length shall be 100-125mm, 1.8-2W per pixel controlled by SPI/DMX 512protocol. The fixture shall be addressable with 10 channels per meter. All the fixtures shall be mounted back to back and continuously for view on both the sides of the suspenders with the help of IP68 connectors. The fixtures lengths should be customized depending on the lengths of the bridge suspenders having the power consumption as 18-20W/mtr. The fixture should have atleast 300 luminous flux. Maximum width of channel up to 55 mm. The desired content on the The product shall be IP67 protected and IK08 rated against any impacts. Input Voltage - 24V DC. Length -1000mm. LED Make - Cree, Nichea, Osram, Lumiled. Installation charges Including rent of use T&P with operator and Skilled labour and cost of 03 nos steel Tie per Linear Pixel LED Light.as per direction by engineer in charge and Complete in all respect. as per Technical Specification . [Suspension Cable (from sr no 14th Suspender to sr no 27th Suspender on inner & outer side ) ]

Supply, installation, testing and commissioning of Linear LED wallwasher profile light which shall be mounted on the inside path of the pylon. The aluminium extrusion housing of the profile shall be customized as per the design of the pylon of the bridge to achieve the illumination on the inside walls of pylon. The fixture shall be provided with the powder coated visor to match the structure of the pylons as per the site requirement of engineer in charge. Each LED shall be single chip RGBW individually controlled to achieve the dynamic effects. The fixture shall be controlled by DMX 512 protocol and shall be mounted with the help of IP68 connectors and 4mm toughened glass on the optics. The fixtures lengths should be customized depending on the lengths of the inside pylon area of the bridge with the power consumption as 24W. The fixture should have atleast 960 luminous flux. The product shall be IP66 protected and IK08 rated against any impacts. Input Voltage - 24V DC, Beam angle - 20-25 degree Length -1000mm. LED Make - Cree, Nichea, Osram, Lumiled. Installation Charges including Skilled Labour and Rent of use T&P to Complete the job and Suitable size Metal Frame With Welding Charges Including Labour ,Nut & bolt Grout on the wall with primer and Final Painting Coatas. as per direction by engineer in charge. and Complete in all respect. as per Technical Specification .(Pylon inside car passage)

Supply, installation, testing and commissioning of Linear pixel LED profile light which shall be mounted on top of pylon area . The Aluminium extrusion housing of the profile shall be customized as per the design of the pylon of the bridge to achieve the illumination on the pylon top area of the bridge. Each LED pixel shall be RGBW individually controlled to achieve the dynamic media effects. The pixel length shall be 100-125mm, 1.8-2W per pixel controlled by SPI/DMX 512protocol. The fixture shall be addressable with 10 channels per meter. All the fixtures shall be mounted back to back and continuously for view on both the sides of the suspenders with the help of IP68 connectors. The fixtures lengths should be customized depending on the lengths of the bridge suspenders having the power consumption as 18-20W/mtr. The fixture should have atleast 300 luminous flux. Maximum width of channel up to 55 mm.The desired content on the The product shall be IP67 protected and IK08 rated against any impacts. Input Voltage - 24V DC. Length -1000mm. LED Make - Cree, Nichea, Osram, Lumiled.Installation Charges including Skilled Labour and Rent of Required Special T&P to Complete the job.as per direction by engineer in charge. and Complete in all respect. as per Technical Specification (Pylon top area)

Supply, installation, testing and commissioning of Linear LED wallwasher profile light which shall be mounted on the pylon outer structure. The aluminium extrusion housing of the profile shall be customized as per the design of the pylon of the bridge to achieve the illumination on the outer sides of pylon. The fixture shall be provided with the powder coated visor to match the structure of the pylons as per the site requirement of engineer in charge.Each LED shall be single chip RGBW individually controlled to achieve the dynamic effects. The fixture shall be controlled by DMX 512 protocol and shall be mounted with the help of IP68 connectors and 4mm toughened glass on the optics. The fixtures length shall be customized depending on the design of the bridge with the power consumption of 24W. The fixture should have atleast 960 luminous flux. The product shall be IP66 protected and IK08 rated against any impacts. Input Voltage - 24V DC. Length -1000mm. Beam angle - 10X30 degree, LED Make - Cree, Nichea, Osram, Lumiled. Installation Charges including Skilled Labour and Rent of use T&P to Complete the job and Suitable size Metal Frame With Welding Charges Including Labour ,Nut & bolt Grout on the wall with primer and Final Painting Coatas. as per direction by engineer in charge. and Complete in all respect.as per Technical Specification (Around the sides of pylon)

Supply, installation, testing and commissioning of LED narrow beam projector light which shall be mounted on the base of the pylon pillars to wash the pillars vertically. The aluminium die cast housing of the fixture must match the design of the bridge to achieve the illumination on the inside and outside pillars of pylon. The fixture shall be provided with the powder coated visor to match the structure of the pylons as per the site requirement of engineer in charge. Each LED shall be single chip RGBW individually controlled to achieve the dynamic effects. The fixture shall be controlled by DMX 512 protocol and shall be mounted with the help of IP68 connectors and 4mm toughened glass on the optics. The power consumption should be 90-100Watts . The fixture should have atleast 3600-4000 luminous flux. The product shall be IP66 protected and IK08 rated against any impacts. Input Voltage - 120-270V AC. Beam angle - 10-15 degree, LED Make - Cree, Nichea, Osram, Lumiled.Installation Charges including Skilled Labour and Rent of use T&P to Complete the job and Suitable size Metal Frame With Welding Charges Including Labour ,Nut & bolt Grout on the wall with primer and Final Painting Coatas. as per direction by engineer in charge for Pylon Entry pillars.(Pylon Pillars)

Supply, installation, testing and commissioning of Linear LED wallwasher profile light which shall be mounted under side glass deck to highlight the pathway glasses. The aluminium extrusion housing of the profile shall be customized as per the design of the side underdecks of the bridge to achieve the illumination on the under side glass deck of the bridge . Each LED shall be single chip RGBW individually controlled to achieve the dynamic effects. The fixture shall be controlled by DMX 512 protocol and shall be mounted with the help of IP68 connectors and 4mm toughened glass on the optics. The fixtures lengths shall be customized depending on the length of the side underdeck with the power consumption of 24W. The fixture should have atleast 960 luminous flux. The product shall be IP66 protected and IK08 rated against any impacts. Input Voltage - 24V DC. Length -1000mm, Beam angle - 35-40 degree, LED Make - Cree, Nichea, Osram, Lumiled. Installation Charges including Skilled Labour and Rent of use T&P to Complete the job and Suitable size Metal Frame With Welding Charges Including Labour ,Nut & bolt Grout on the wall with primer and Final Painting Coatas per. as direction by engineer in charge. and Complete in all respect. as per Technical Specification.(Under Deck lighting)

Supply, installation, testing and commissioning of LED Medium beam projector light which shall be mounted on the side stay cables. The aluminium die cast housing of the fixture must match the design of the bridge to achieve the illumination on the side stay cable of the bridge.The fixture shall be provided with the powder coated visor to match the structure of the pylons as per the site requirement of engineer in charge. Each LED shall be single chip RGBW individually controlled to achieve the dynamic effects. The fixture shall be controlled by DMX 512 protocol and shall be mounted with the help of IP68 connectors and 4mm toughened glass on the optics. The power consumption should be 350-380Watts . The fixture should have atleast 14000-15200 luminous flux. The product shall be IP66 protected and IK08 rated against any impacts. Input Voltage - 120-270V AC. Beam angle 20-25 degree, LED Make - Cree, Nichea, Osram, Lumiled. Installation Charges including Skilled Labour and Rent of use T&P to Complete the job and Suitable size Metal Frame With Welding Charges Including Labour ,Nut & bolt Grout on the wall with primer and Final Painting Coatas. as per direction by engineer in charge.and Complete in all respect. as per Technical Specification (Sides Stay Cable ).

Supply, installation, testing and commissioning of Medium beam projector light which shall be mounted on the poles in the ghat area for general dynamic illumination at floor and water. The aluminium die cast housing of the fixture. The fixture shall be provided with the powder coated visor as per the site requirement of engineer in charge. Each LED shall be single chip RGBW individually controlled to achieve the dynamic effects. The fixture shall be controlled by DMX 512 protocol and shall be mounted with the help of IP68 connectors and 4mm toughened glass on the optics. The power consumption should be 150 Watts . The fixture should have atleast 6000 luminous flux. The product shall be IP66 protected and IK08 rated against any impacts. Input Voltage - 120-270V AC. Beam angle - 40-45 degree, LED Make - Cree, Nichea, Osram, Lumiled. Installation Charges including Skilled Labour and Rent of use T&P to Complete the job and Suitable size GI Bracket to be Mounting on the Pole With Welding Charges Including Labour ,Nut & bolt Grout on the wall with primer and Final Painting Coatas. as per direction by engineer in charge.and Complete in all respect. as per Technical Specification. (Ghat Seating area General Lighting).

Supply, installation, testing and commissioning of Linear LED guardrail round section profile light which shall be mounted on the railing structure. The aluminium housing of the profile shall be customized as per the design of the railing. The fixture shall be provided with the anti glare lenses to avoid any glare into the traffic or human movment as per the site requirement of engineer in charge. Each LED shall be single chip monochromatic 3000-4000K. The fixture shall be connected with the help of IP68 connectors and 4mm toughened glass on the optics. The fixtures length shall be customized depending on the design of the bridge with the power consumption of 18W. The fixture should have atleast 720 luminous flux. The product shall be IP66 protected and IK08 rated against any impacts. Input Voltage - 24V DC. Length -1000mm. Beam angle - 10X30 degree, LED Make - Cree, Nichea, Osram, Lumiled.Installation Charges including Skilled Labour and Rent of use T&P to Complete the job and Suitable size Metal Frame With Welding Charges Including Labour ,Nut & bolt Grout on the wall with primer and Final Painting Coatas. as per direction by engineer in chargeand Complete in all respect. as per Technical Specification.(Approach Road ).

Supply, installation, testing and commissioning of Linear LED guardrail round section profile light which shall be mounted on the railing structure. The aluminium housing of the profile shall be customized as per the design of the railing. The fixture shall be provided with the anti glare lenses to avoid any glare into the traffic or human movment as per the site requirement of engineer in charge. Each LED shall be single chip monochromatic 3000-4000K. The fixture shall be connected with the help of IP68 connectors and 4mm toughened glass on the optics. The fixtures length shall be customized depending on the design of the bridge with the power consumption of 18W. The fixture should have atleast 1080 luminous flux. The product shall be IP66 protected and IK08 rated against any impacts. Input Voltage - 24V DC. Length -1000mm. Beam angle - 10X30 degree, LED Make - Cree, Nichea, Osram, Lumiled.Installation Charges including Skilled Labour and Rent of use T&P to Complete the job and Suitable size Metal Frame With Welding Charges Including Labour ,Nut & bolt Grout on the wall with primer and Final Painting Coatas. as per direction by engineer in charge.and Complete in all respect. as per Technical Specification (Upper Deck Road Lighting ).

Supply, installation, testing and commissioning of Linear LED Durable & weather proof IP65 light which shall be mounted under the deck for general illumination. The polycarbonate extrusion housing of the profile along with the transparent diffuser. The LED shall be mounted on the MCPCB with the power consumption of 40 Watts, PF>0.9, CCT-5700K The fixture should have atleast 2520 luminous flux. The product shall be IP65 protected and IK08 rated against any impacts. Input Voltage - 120-270V AC. Length -1000mm, LED Make - Cree, Nichea, Osram, Lumiled. Installation Charges With Cost of Welding making hole for nut and bolt including charges of use T&P to Complete the job.as per direction by engineer in charge.and Complete in all respect. as per Technical Specification. (Inside Deck Walk Way ).

Supply and Instalaltion of IP67 metal housing power supply 24V output. Power consumption- 240W driver featuring the constant power mode. Power supply should operate from100~305VAC and offers models with different rated current ranging between 700mA and 6.66A. High efficiency up to 93%, with the fanless design, must be able to operate at -40°C ~+90°C case temperature under free air convection. The design of metal housing and IP67 ingress protection level should be suitable for theoutdoor applications. Must be designed with the latest version of IEC61347/GB7000.1-2015 and UL8750 international safety regulations. The output and dimming circuit are also completely in accordance with the new regulations with isolation to ensure the user and luminaire system safety dung installation. Installation Charges including of use T&P to Complete the job.as per direction by engineer in charge and Complete in all respect.

SITC of DMX 512 Controller system with 2.0 GHz, Dual core CPU, monitor screen 18/21 inches, Wireless Mouse and key board ,open GL 2.1 Graphic Card, 2GB Ram, 1GB free Harddisk space. Installation Charges including charges of use T&P to Complete the job.as per directon by Engineer in Incharge and Complete in all respect.

Supply and Instalaltion of Signal Amplifier/Splitter with 4/8-Way output for spreading and amplifying the DMX Data signals in multiple directions, Input-220-240V AC.Installation Charges including charges of use T&P to Complete the job.as per directon by Engineer in Incharge.and Complete in all respect.

Supply and Instalaltion of SPI/DMX Multi-Protocol Converter that accepts an Ethernet connection, and transmits DMX 512 light data to up to eight universes of luminaires.Installation Charges including charges of use T&P to Complete the job.as per directon by Engineer in Incharge.and Complete in all respect.

Programming, synchronizing of the various scenes as per the site requirements to achieve the dynamic media effects of LED Pixel & RGB Fixture of Mounted on the Complete Bridge. as per directon by Engineer in Incharge and Complete in all respect.

Suply and Laying of DMX Special cable DMX cable (single pair) having one 22AWG pair stranded (7x30) tinned copper conductors, Datalene (FHDPE) insulation, twisted pairs, overall Beldfoil shield (100% coverage) plus tinned copper braid, PVC jacket Cable.as per directon by Engineer in Incharge and Complete in all respect.

Supply and installation of networking key to run the controller upto 128 Universes (Up gradable at extra cost upto 2048 universes).as per directon by Engineer in Incharge and Complete in all respect.

SITC OF Street Light Luminaire for Approachs to bridge:Supply of Street luminaire suitable for outdoor applications.Luminaires should be enabled with high power LEDs, should consists of highly efficient,UV and temperature-resistant optics with street light distribution. With tiughened clear glasscover,clear/powder coated.Luminaire efficacy should be atleast 110 lm/Watt system level.Power consumption shouldbe 60 W.Power factor of the luminaire shall be more than 0.90.The lumen maintenance L70@ B-50 of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours.Ingress Protection should be IP66 or higher.Housing should be made of pressure Diecast Aluminium impact resistance level should be IK08.Adequate heat sink with proper thermal management shall be provided.Operating Temperature:-5°C to + 50°C, Operating Humidity:10%-90% & 4kV inbuilt and 10kV external surge protection with Top opening driver cover for easy maintenance.as per directon by Engineer in Incharge.and Complete in all respect.

Supply and Errection of 7mtr hight hot dip galvanised Octagonal Pole with 130mm Bottom A/F and 70mm Top A/F made up of 3mm thick HT Sheet Along with base plate of size 200x200x16mm thick PCD-200mm 1mtr long hot dip galvanised single Arm standard bracket up of 40NB dia GI pipe to Mounting on pole having top 70mm A/F.including casting of foundation as per design & drawing for 7 Mtr poles along with RCC base foundation and 4Nos of M20X600 long 'J' type EN 8 Grade foundation bolt along with template and pole shall be suitable to withstand wind speed as per IS-875 IEC & BIS.and excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres.as per directon by Engineer in Incharge.and Complete in all respect.

Supply & laying of following size of Cables

S/L of 4 C X 150 sq mm AL Armoured Cable Complete in All respect and as per directon by Engineer in Incharge .

S/L of 4 C X 95 sq mm AL Armoured Cable Complete in All respect and as per directon by Engineer in Incharge .

S/L of 4C X 6 sq mm AL Armoured CableComplete in All respect and as per directon by Engineer in Incharge .

S/L of 4C X 10 sq mm CU Armoured Cable Complete in All respect and as per directon by Engineer in Incharge .

S/L of 4C X 6 sq mm CU Armoured Cable Complete in All respect and as per directon by Engineer in Incharge .

S/L of 4C X 4 sq mm CU Armoured Cable Complete in All respect and as per directon by Engineer in Incharge .

S/L of 3C X 2.5 Sq mm Cu Armoured PVC Insulated Cable Complete in All respect and as per directon by Engineer in Incharge .

S/L of 3C X 4 Sq mm Cu Armoured PVC Insulated Cable Complete in All respect and as per directon by Engineer in Incharge .

S/L of 3C X 1.5 Sq mm FR Insulated Industrial flexible Copper Conductor Cable Complete in All respect and as per directon by Engineer in Incharge .

Supply & installation of following GI & HDPE Pipe and Cable Tray Items:

Supplying and installing following 150 mm width X 50 mm depth X 1.6 mm thickness of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as per directon by Engineer in Incharge and Complete in All respect.

Supplying and installing following 150 mm width X 50 mm depth X 1.6 mm thickness of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. as per directon by Engineer in Incharge and Complete in All respect.

S/L of 75 mm dia. HDPE pipe SDR 11 ISI as per directon by Engineer in Incharge and Complete in All respect.

S/L of 63 mm dia. HDPE pipe SDR 11 ISI as per directon by Engineer in Incharge and Complete in All respect.

S/L of 40 mm dia. HDPE pipe SDR 11 ISI as per directon by Engineer in Incharge and Complete in All respect.

S/L of 80 mm dia GI pipe Medium Class. as per directon by Engineer in Incharge and Complete in All respect.

S/L of 65 mm dia GI pipe Medium Class. as per directon by Engineer in Incharge and Complete in All respect.

S/L of 40 mm dia GI pipe Medium Class. as per directon by Engineer in Incharge and Complete in All respect.

Supply & termination of following sizes of cables using Aluminium lugs:

S/L of 150 sq mm AL Armoured Cable

S/L of 95 sq mm AL Armoured Cable

S/L of 70 sq mm AL Armoured Cable

S/L of 6 sq mm AL Armoured Cable

Supply & termination of following sizes of cables using Copper lugs:

S/L of 10 sq mm CU Armoured Cable

S/L of 6 sq mm CU Armoured Cable

S/L of 4 sq mm CU AL Armoured Cable

S/L of 2.5 sq mm CU AL Armoured Cable

Supply & termination of following sizes of cables using polyamide glands :

S/L of 4C X 150 sq mm AL Armoured Cable

S/L of 4C X 95 sq mm AL Armoured Cable

S/L of 4C X 70 sq mm AL Armoured Cable

S/L of 4C X 6 sq mm AL Armoured Cable

S/L of 4C X 10 sq mm CU Armoured Cable

S/L of 4C X 6 sq mm CU Armoured Cable

S/L of 4C X 4 sq mm CU Armoured Cable

Supply & installation of following Earthing Material:

SITC of UL Listed maintenance free, low carbon, Copper coated earth rod of 3 meter electrode having dia meter of 14.2 mm with copper coating thickness of 250 micron tested as per IEC 62561-2+ Universal Clamp (SS), 14mm +earth Continuity enhancing mineral compound shall be of 25 Kg/Pit tested as per IEC 62561-7 , TCLP tested OEC 2 25 + the above arrangment shall be provided with Heavy duty earth chamber of 5000 Kg load bearing capacity to ensure the safety of earthing system under floor eath inspection pit.

Providing and fixing 25 mm X 5 mm CU strip on surface or in recess for connections etc. as required.

Supplying and laying 6 SWG G.I. wire in 15 mm Dia G.I Pipe for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.

SITC of 32A 3P 10KA 415V AC 50Hz MCCB as incomer With SS Enclosure,Neatral link ,Earth link and Speader Terminal for incomming & outgoing. as per directon by Engineer in Incharge and Complete in All respect.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 Way SPN DB Double Door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

4 Way TPN DB Double Door

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40A DP Isolator

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40A FP Isolator

Supplying and fixing, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

5 A to 32 A rating SP

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group "B"

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required

SITC of Cable junction box IP66/667 Weather proof for outdoor installation cable size 4-10 sq mm with knockouts for cable entry with terminal Box size - (130 x 80 x 177) mm. as per directon by Engineer in Incharge and Complete in All respect.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

10 X 6 sq. mm + 2 X 6 sq. mm earth wire

S/F of 22 W LED Cool Day Light Aluminium Batten Fitting . as per directon by Engineer in Incharge and Complete in All respect.

The Design, manufacture, supply, installation, testing and commissioning of 2.0 mm thick MS sheet steel fabricated cubicle type Outdoor Panel with canopy and suitable height stand. dust and vermin proof complete with hinged and lockable doors. Individual removable gland plates shall be provided at the bottom of the cable chamber. Adequate size earth bus shall be provided and the same shall be extended out side of the panel to facilitate earth flat connection. The panel shall be given one coat of red oxide primer and two coats of enamel paints. he finishing colour shall be white enamel inside and shade 632 of IS 5 out side.The Sheet Steel shall under go minimum eight tank treatment followed by finishing treatment of powder coating with 70 micron minimum thickness. All the panels shall be floor mounted and dead front construction complete with interconnections. The panels shall be FRONT operated, with cable entry from the top bottom.(All MCB to be "C" Curve) ,All live accessible parts shall be shrouded with 1mm thick polycarbonate/3 mm thick FRP sheet and all equipment shall be finger touch proof. SMC shrouds and busbar supports shall be used. All MCCB door handle shall be interlocked and lockable in OFF position. Galvanised hardware with zinc passivation shall be used in fabrication of Switchboards.Suitable Size Copper earth bus to be provided throughout the length of Switchboards. 2A SP MCBs shall be used as backup protections. All MCCBs shall be variable plug setting type with thermal magnetic Ics = 100% Icu & rotary handle. All control & power wiring shall be broughtout upto the cable alley in the terminal blocks.An approval shall be taken for each panel before manufacturing. Provision of one 6/16 amp socket & compartment lighting for each vertical section of main panel. All breaking Capacity for MCCB to be Ics=100%Icu. Digital Multifunction meter (MFM-4) with RS-485 communication port for measurement of PF, V, A & Hz , equivalent to EM6459, with CT as required. Phase indicating lamps RYB with 2 Amps SP MCB back up protection. Electrolytic high conductivity Copper three phase and neutral busbars rated at 300 amps, 25KA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Current density of Bus Bar to be 1.6 sq.mm / amp.There shall not be any access from bus bar chamber to other chambers. The bus bar shall be colour coded. The tapping for the individual switches shall be suitable size copper bus connection through insulated barriers without any gap. No instruments or components shall be mounted on the chamber. 40KA Type II (3P+N) Surge protection device with 32A FP C -Curve MCB, Spreader Terminal, Direct ROM. Astro Time Switch having following facilities:Precise time programming for-Daily/Weekly,Pulse switching,Simple Reset feature,Week end programming,Red LED for relay ON Indication, 24 Hr display (Military), Manual Over ride. Supply Voltage & Frequency:110-240VAC,+10%/-20%,50/ 60 Hz; Memory Locations: 8 On / Off operations, 16 memory locations; Minimum Switching Time: 1 min; Housing: Flame Retardant UL94V0. Digital Ampere,Voltmeter for measurement of Current and Voltage with CT as required.On Indication Lamp Green LED for relay ON ,Off Indication Lamp Red LED for relay Trip, Auto and Manual Switch. Incomer - 250A FP MCCB (TM-R) (36 KA) - 1 No. & 250A FP 415V ON Load change Over Switch-01 Nos. feeder 1 Outgoings - 100A FP MCCB(TM-R) (25 kA) - 1 Nos & 100A FP Contactor- 01 Nos , 20A TPN MCB (10 kA) -10 Nos feeder 2 Outgoings - 100A FP MCCB(TM-R) (25 kA) - 1 Nos Outgoings- 32 A FP MCCB (TM-R) (18 kA) - 3 Nos as per directon by Engineer in Incharge and Complete in All respect.

The Design, manufacture, Supply, Installation, Testing & Commissioning of following Lighting Panel: 3 Phase,415V Lighting panel, Out door type with canopy, free standing,double door with lockable arrangement made from 2 mm thick CRCA sheet steel,The panel shall be given one coat of red oxide primer and two coats of enamel paints. powder coated with off white colour (inside & outside),1no.earth stud on each side face, Phase indicating lamps RYB with 2 Amps SP MCB back up. Electrolytic high conductivity Copper three phase and neutral busbars rated at 160 amps, 25KA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. 40KA Type II (3P+N) Surge protection device and having following: Incomer: 100A 4P MCCB (TM-R) (25 kA) - 1no., 100A 4P contactor -1no.Direct ROM, Spreader Terminal, Astro Time Switch having following facilities:Precise time programming for-Daily/Weekly,Pulse switching,Simple Reset feature,Week end programming,Red LED for relay ON Indication, 24 Hr display (Military), Manual Over ride. Supply Voltage & Frequency:110-240VAC,+10%/-20%,50/ 60 Hz; Memory Locations: 8 On / Off operations, 16 memory locations; Minimum Switching Time: 1 min; Housing: Flame Retardant UL94V0. Digital Ampere,Voltmeter for measurement of Current and Voltage with CT as required.On Indication Lamp Green LED for relay ON ,Off Indication Lamp Red LED for relay Trip, Auto and Manual Switch. Outgoing: 32A 4P MCCB (TM-R) (18kA) - 1 no, 20A TPN MCB (10 kA) -10 Nos as per directon by Engineer in Incharge and Complete in All respect.

Supplying and fixing following 6 Module size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.(01 Nos 5A + 01 Nos 15A) modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following 6 Module size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.(02 Nos 5A) modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 amps switch

3 pin 5/6 amp socket outlet

Supply and fixing of 32A 415V 4P Bus-Bar Chamber including Connection. as per directon by Engineer in Incharge and Complete in All respect.

Supply and fixing of Shockproof and rustproof, 100% Water Proof, Mounting arrangement, Rot-proof and termite resistant,Cable entry from the bottom/sides SMC Junction Box.(240x130x95).as per directon by Engineer in Incharge and Complete in All respect.

Supply and installation of 8 port 10/100/1000 Base-T PoE Gigabit Smart switch, Switching Capacity 20 Gbps,Packet buffer memory, 4.1 Mbits, Maximum forwarding rate 14.9 Mpps, POE standard IEEE 802.3af and IEEE 802.3at,operating Temperature -5 to 50 dgree C,Storage Temperature -20 to 70 dgree C, Acoustics 0 dB(A) 2 x 2 RJ45, Combo port Including SFP with 54V DC external Power Adapteras per directon by Engineer in Incharge and Complete in All respect.

AMAR ELECTRIC CO