REPAIR/MAINT OF JOINERY, PLUMBING AND SANITARY FITTINGS/FIXTURES, ROOF SHEETING, CEILLING, FLOORING ETC TO OTM ACCN ZONE A AT KANCHRAPARA UNDER GE BARRACKPORE

Amount

Taking down chowkats with shutters (without taking off shutter from the frames) not exceeding 1.50 Sqm each all as specified and directed.

Taking down chowkats with shutters (without taking off shutter from the frames) exceeding 1.50 Sqm and not exceeding 4.00 Sqm each complete all as specified and directed.

Taking down of shutter of any description exceeding 1 Sqm and not exceeding 2.0 Sqm each all as specified and directed.

Taking down of shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm and refixing in same opening after easing and adjusting all as specified and directed.

Taking down of shutter of any description not exceeding 1 sqm each all as specified and directed.

S&F for factory made steel windows with side hung shutters including box type hinges with steel handle, frame, steel peg stay, complete with glazing bars, dovetailed or welded to receive wire mesh/glass including one coat of red oxide zinc chrome primer at factory complete all as specified and directed.

S&F for factory made steel windows with side hung shutters including box type hinges with steel handle, frame, steel peg stay, complete without glazing bars, dovetailed or welded to receive wire mesh/glass including one coat of red oxide zinc chrome primer at factory complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over and including a coat of red oxide primer after preparation of new steel surfaces of any description over 10cm width or girth complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint after preparation of old painted steel surfaces of any description, over 10cm in width or girth, not otherwise described all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or forged into spikes; framed guard bars; barred iron doors; ladders, railings, framed brackets, walk ways, frame work of water tank and similar work conforming to Fe-290-0 Gde-E-165 complete as in repair all as specified and directed.

S&F for pressed steel frames (factory made) for door of size 125mm X 60mm of 1.25mm thick with one or more rebates including necessary fittings lugs, hinges, lock strike plate, etc including filling of concrete (1:3:6) type C-0 (using 12.50 mm graded crushed stone aggregate) with and including applying of two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed.

S&F for pressed steel frames (factory made) for door of size 105mm X 60mm of 1.25mm thick with one or more rebates including necessary fittings lugs, hinges, lock strike plate, etc including filling of concrete (1:3:6) type C-0 (using 12.50 mm graded crushed stone aggregate) with and including applying of two coats of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed.

S&F for second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints of second class hard wood etc complete all as specified and directed.

S&F for mild steel hold fast made out of flat iron (25mm x 3mm) including tarring or coal tar black paint and with drilling necessary holes etc conforming to Fe 410-0 or Fe 310-0 all as specified and as directed.

M&L for PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) used as in brick, concrete wall for fixing of hold fast including necessary form work all as specified and directed.

S&F for 35mm thick, second class hard wood plain frames, panelled (factory made) shutters with lock rails and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS-1003 (Part-I) (larger size to be provided) klin seasoned and chemically pressure treated fitted to chowkats complete all as specified and as directed.

S&F for 35mm thick second class hard wood glazed/ gauge & skeleton shutters (factory made), open rebated & prepared to receive glass, gauge etc. (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing glass etc. sizes of members of shutters as specified in SSR part-I, section-8, clause 8.24 (a) (larger size to be provided) complete all as specified and directed.

S&F for 30mm thick second class hard wood glazed/ gauge & skeleton shutters (factory made), open rebated & prepared to receive glass, gauge etc. (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitered beads for securing glass etc. sizes of members of shutters as specified in SSR part-I, section-8, clause8.24 (a) (larger size to be provided) complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer after preparation of new wooden surfaces of any description over 10 cm girth or width complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint after preparation of old painted wooden surfaces of any description, not otherwise described, over 10cm in width or girth complete all as specified and directed.

S&F for factory made solid PVC door frame of size 50mm X 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube as per specification and drawing complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified.

S&F for 18/19 mm thick prelaminated particle board fix in cupboard shelves & shutter interior grade, prelaminated in one side with decorative choice lamination solid core medium density general purposes, and other side white lamination fixed with screw including teakwood lipping as in repair all as specified and directed.

S&F for anodised (powder coating of minimum thickness 50 micron) aluminum frame for doors , windows, ventilators with one or more rebates (sliding & fixed type) including joining cleat for fixing etc complete all as specified and directed

S&F for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel (heavy duty) complete as in repair all as specified and directed.

Taking down aluminium shutter exceeding 1.50 Sqm and not exceeding 3 Sqm each leaf and refixing in same opening after repairs providing cleat, pivot, beading, gasket, lock or any other minor parts as required all as specified and directed.

Hacking out old broken glass (any thickness size quality or description) from wooden or steel frame, glazed with putty or fixed with beads etc complete all as specified and as directed.

S&F for stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with stainless steel wire staple complete all as specified and directed.

S&F for stainless steel wire cloth, 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with stainless steel wire staple complete as in repair all as specified and directed.

S&F for 5.5mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares not exceeding 0.50 sqm each pane all as specified and directed.

S&F for 5.5mm thick sheet glass tinted fixed with beads complete area exceeding 0.50 Sqm each pane complete all as specified and directed.

S&F for 3mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares not exceeding 0.50 sqm each pane all as specified and directed.

S&F for 100 mm long stainless steel butt hinges, medium weight complete all as specified and directed.

S&F for 75 mm long stainless steel butt hinges, medium weight complete all as specified and directed.

S&F for 250 mm aluminum alloy, anodised , sliding door bolt with hasp and staple (bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed complete all as specified and directed.

S&F for 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 100 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 150 mm long aluminium anodised extruded alloy handle fabricated type complete all as specified and directed.

S&F for 100 mm long aluminium anodised extruded alloy handle fabricated type complete all as specified and directed.

S&F for 25mm bore mild steel powder coated, single curtain rod (wall thickness not less than 1mm) including fancy type PVC powder coated brackets (as approved by GE), funnels etc suitable for single curtain rod, fixed etc complete as in repair all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlars facing dressed stonework & precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar (1:6) complete all as specified and directed.

All as per Item No.42.00 here-in-before but except bricks complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

Taking down cement plaster of any description on brick or stone or concrete surface of wall etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:3) on ceiling surfaces, finished fair and even without using extra cement complete all as specified and directed

M&L for rendering 15mm thick in cement mortar (1:4) on brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying two coats of cement based paint over a coat of alkali resistance primer on newly plastered surface of walls including preparation of surface complete all as specified and directed.

M&L for applying two coats of distemper oil emulsion over a coat of alkaline resistant primer after preparation of newly plastered surfaces of walls complete all as specified and directed.

M&L for applying three coats of white wash on surface of wall including preparation of new plastered surface complete all as specified and directed.

M&L for applying three coats of white wash on surface of ceiling including preparation of new plastered surface complete all as specified and directed.

M&L for applying one coat of oil emulsion distemper over old distemper plaster surfaces of wall after preparation of surfaces complete all as specified and directed.

M&L for applying two coats of oil emulsion distemper over a coat of alkaline resistant primer over 2 mm thick wall care putty on wall as directed by GE as per site condition after complete removal of existing treatment of wall including preparation of old painted wall surfaces complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors & pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate) as in plinth protection/paving including finishing the cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in subbase of floor complete all as specified and directed.

M&L for pre-polished coloured chequered cement concrete tiles 30cm x 30cm x 25mm thick (glossy type), set, jointed and pointed in neat cement slurry in floors with grey cement and pigments over and including 15 mm thick cement screed bed in cement mortar (1:6) including dismantling old tiles complete all as specified and directed.

M&L for non skid (joint free) ceramic coloured (colour & shade as approved by GE) tiles of 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in colour cement to match over and including 15mm thick Screed bed or beading layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L for non skid (joint free) ceramic coloured (colour & shade as approved by GE) tiles of 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting/dado/riser of step etc set and jointed in neat cement slurry and pointed in colour cement to match over and including 15mm thick Screed bed or beading layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed.

M&L for glazed ceramic coloured tiles (colour & shade as approved by GE) in vertical surface of size 450mmX 300mmX7 to 8mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick screed bed of cement mortar (1:4) complete all as specified and directed.

M&L for glazed ceramic coloured tiles (colour & shade as approved by GE) in vertical surface of size 300mmX 200mmX7 to 8mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick screed bed of cement mortar (1:4) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 20mm thick granite slab (any type) work (table rubbed and polished) machine cut in steps, jambs, pillars, window cill, cooking platform etc bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the granite stone including and polishing over and including 15mm thick cement mortar (1:4) complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations not exceeding 15mm wide complete all as specified and directed.

Demolition of reinforcement cement concrete of any description and in any position not otherwise specially provided for complete all as specified and directed.

M&L for precast reinforced cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in cover slab/slab of drain/manhole, water tank/shelf, landing, cooking platform set in cement mortar (1:4) complete all as specified and directed. (NOTE: Cost of Form Work is deemed to be inclusive of unit rate quoted by the contractor & reinforcement shall be measured & paid Separately.)

M&L for TMT bars 10 mm dia and over cut to length bent to shape as required including cranking, bending spirally for hooping for columns, hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi-corrugated etc.) sheets in roof coverings complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet of 0.50mm thick of any colour as approved by GE having tensile strength of 550 Mpa as in ridge to wall/cladding, fixed with self tapping screws complete all as specified and directed.

M&L for 6mm thick fibre asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc. fixed with 'L' or 'J' type hooks complete all as specified and directed.

All as per Item No.72.00 here-in-before but except sheets.

M&L for 6mm thick fibre asbestos cement two pieces adjustable serrated ridge for corrugated or semi- corrugated sheets fixed with 'L' or 'J' type hooks complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering etc all as specified and directed.

M&L for 0.63 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip & straight flashing (legth & girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

M&L for 0.63 mm thick plain, galvanised, corrugated mild steel sheeting with two corrugated side lap fixed with coach screws & washers, in roofs, wall etc with grade of zinc coating 275 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description etc complete all as directed.

S&F for mild steel flat iron of size 25X6 mm as in wind tie including all necessary drilling, bolting or riveting etc and similar work complete conforming to Fe-290 Gde E-165 all as specified and directed.

Dismantling structural steel work of tubular purlins including doors, gates but excluding framed truss etc. complete all as specified and directed.

S&F for rolled mild steel work in tubular trusses and purlins including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillet all as specified and directed.

Dismantling timber scantlings (framed work) 40 sq.cm and over in section, in any position complete all as specified and directed.

Dismantling timber in fillets, rails posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and directed.

S&F for false ceiling with exposed metal (PPGI) framework/ “Tee” Grid providing and fixing of suspended Tee gird false ceiling using “T” Gird System – powder coated GI (PPGI) exposed grid false ceiling suspension system in grid size 600mm x 600mm with main runner 32 x 24mm x 0.3mm thick, cross tee 26mm x 24mm x 0.3mm thick and wall angle 24mm x 24mm x 0.40mm thick using 4mm thick non asbestos fibre cement board (oceanic) of size 595 x 595mm, an asbestos Free fibre cement board manufacture using high Pressure System Curing technology. T gird Framing is suspended using 4mm GI/MS bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip, also providing provisions for light fixtures, air conditioning diffusers and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at not more that 300mm from the adjacent wall. 1220mm/600mm Cross Tee to be interlocked between main runners @ 600mm c/c, so as to from 600mm x 600mm or 1200mm x 600mm grid, confirming IS 14862 & type B category III of ISO 8336, tested as per AS 1530 part – 3 & B. S- 476 part 4,5,6,7 & 8 should be placed in Gird module to form complete as per the drawing & directions of Engineer-in-Charge.

S&F for solid PVC wall lining consisting of 5mm thick single side prelam PVC sheet used inclusive of solvent cement & fixing at site on PVC frame as per specification & drawing complete all as specified and directed.

S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification & drawings complete all as specified and directed.

Taking up or down steel tubings & connections including cleaning for refixing or removal from site for 15 mm bore pipes complete all as specified and directed.

Refixing old steel tubings & connections in new or old position (wall, ceiling, floor etc.) for 15mm bore pipes with new fittings etc complete all as specified and as directed. (Note : Pipe shall be obtained from Item No 88.00 above)

S&F for 15mm dia tubes (medium grade) galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) complete all as specified and directed.

Taking up or down steel tubings & connections including cleaning for refixing or removal from site for 20 mm bore pipes complete all as specified and directed.

Refixing old steel tubings & connections in new or old position (wall, ceiling, floor etc.) for 20mm bore pipes with new fittings etc complete all as specified and as directed. (Note : Pipe shall be obtained from Item No 91.00 above)

S&F for 20mm dia tubes (medium grade) galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors, wall etc (surface or concealed type) complete all as specified and directed.

M&L for cutting chases, in brick wall and making good to facing where required and pointing in cement mortar (1:3), to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exceeding 10cm girth complete all as specified and directed.

S&F for 15 mm bore stop valve, fancy type chromium plated , cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete as in repair all as specified and directed.

S&F for 15 mm bore stop valve, fancy type chromium plated with long shank and cup (concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete as in repair all as specified and directed.

S&F for 15mm dia bib taps, cast copper alloy, fancy type, chromium plated with flange complete as in repairs all as specified and directed.

S&F for vitreous china wash basin, white, flat back, size 550 X 400mm, excluding taps, chain and plug and porcelain stopper but including 32mm dia PVC waste pipe, brackets (02 Nos), 32mm size full threaded brass chromium plated waste coupling etc and cutting for and pinning in ends of brackets or erecting stand complete as in repair all as specified and directed.

S&F for 15mm dia pillar taps, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with letter 'HOT' or 'COLD' with long screwed shanks & fly nuts, screwed for iron pipes complete as in repair all as specified and directed.

S&F for brass chromium plated tubular towel rail, 20mm dia, D-type, 60cm long between flanges as in repairs all as specified and as directed.

S&F for 125mm size brass chromium plated shower roses with arms, swivel joints, including fixing to steel pipe or union complete as in repair all as specified and as directed.

S&F for glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete as in repair and all as specified and directed.

S&F for shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) in repairs complete all as specified and directed.

S&F for vitreous china squatting pan 'Orissa' pattern, size 580x440mm white, with integral foot rests with P or S trap (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti-syphonage pipe etc complete including making good to floors with PCC bedding (1:5:10) type E2 using 40mm nominal brick ballast and connection to trap with cement mortar all as specified, and making good to floor including demolition of PCC / lime concrete bedding existing pan complete as in repairs all as specified and directed.

S&F for vitreous china wash down water closet pan (pedestal pattern) white with 'P' or 'S' trap type (excluding flushing cistern & flush pipe) including connection to trap & to flushing pipe, anti-syphonage pipe out in and including white seat cover etc. complete as in repair including making good to floor complete all as specified and directed.

S&F for 125mm long health faucet (ABS) with rubbit cleaning system, one meter long PVC flexible tube for 15mm dia and ABS wall hook complete as in repair all as specified and directed.

S&F for 10 Ltrs capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete with all internal accessories and fixed to wall and jam nuts on both sides, PVC flush pipe 32mm dia 90cm long fixed properly to inlet of WC and making good to disturbed surfaces of wall or floor complete as in repair all as specified and directed.

S&F for vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe(excluding flushing cistern but including flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2) securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete as in repair all as specified and directed.

S&F for vitreous china urinals, half stall type, fixed in repair including waste coupling 32mm size full thread, brass, chromium plated, waste pipe and all necessary fittings including dismantling old urinal bowl etc complete all as specified and directed.

S&F for PVC water closet seat, white/black colour as required, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete as in repair all as specified and directed.

S&F for PVC connection pipe 15 mm size with PTMT nuts of length 600 mm complete as in repair all as specified and as directed.

S&F for 1000 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) multi layer (three layer) hoisted and fixed in position with cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection, including 20mm ball valve high pressure of PTMT including dismantling / taking down old PVC water tank, ball valve etc complete all as specified in SSR Part-I all as specified and directed.

S&F for 500 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) multi layer (three layer) hoisted and fixed in position with cover of tank with its locking arrangement, making hole for inlet, outlet and overflow connection, including 15mm ball valve high pressure of PTMT including dismantling / taking down old PVC water tank, ball valve etc complete all as specified in SSR Part-I all as specified and directed.

S&F for 15mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe & fixed (minimum weight 142 gms) complete as in repairs all as specified and directed.

S&F for 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe & fixed (minimum weight 210 gms) complete as in repairs all as specified and directed.

S&F for 15mm dia gun metal gate valves with iron wheel head screwed both ends for iron pipes or for unions pipes, fixed as in repairs all as specified and directed.

S&F for 20mm dia gun metal gate valves with iron wheel head screwed both ends for iron pipes or for unions pipes, fixed as in repairs all as specified and directed.

S&F for sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete as in repair all as specified and directed.

Taking down eaves gutters and rainwater pipe (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches as in floor complete all as specified and directed.

S&F for 110 mm bore PVC (SWR) bends any radius complete as in repair all as specified and directed.

S&F for 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches or in floor complete all as specified and directed.

S&F for 75 mm bore PVC (SWR) bends any radius complete as in repair all as specified and directed.

S&F for 100 mm dia CP grating doom (minimum weight 25 gms) complete as in repair all as specified and directed.

S&F for 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete as in repair all as specified and directed.

S&F for anodised (powder coating of minimum thickness 50 micron) aluminium door shutters (powder coated), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F for anodised (powder coating of minimum thickness 50 micron) aluminium window/ventilators shutters, sliding/fixed type without sash bar, aluminum section weighing 0.55 Kg/m, including necessary joining cleat, glazing clips, rubber neoprene packing, handle 2 Nos in each door, hinges, peg stay, anodised aluminium snap beading, screws etc complete locking arrangement, roller all as specified and directed.

M AND D CONSTRUCTION