SPECIAL REPAIR FOR REPLACEMENT RE-ROUTING OF CI GI PIPE LINE AND CERTAIN SANCTIONED WORKS AT ALHILAL MIL STN

Amount

SCHEDULE 'A' PART-I (B/R WORKS) Surface excavation over area not exc. 30 m deep in any type of soil and getting out complete all as specified.

Excavating over areas, n exc 1.5 m deep and getting out getting out in hard/dense soil complete all as specified.

Plain cement concrete, M-10 (Nominal Mix), type C-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete, complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6, complete all as specified and directed.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick in mortar 1:6, complete all as specified and directed.

Returning filling in (soil) incl spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point, complete all as specified.

M&L, reinforced cement concrete, M-15 (Nominal Mix), type B-1(using 20mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams, roof beams, bases for columns, etc.; basement slabs, under reamed piles and mass concrete etc, complete all as specified.

M&L, reinforced cement concrete, M-15 (Nominal Mix), type B-1(using 20mm graded crushed stone aggregates) as in Columns, pillars, piers, posts and struts, complete all as specified.

M&L, reinforced cement concrete, M-15 (Nominal Mix), type B-1(using 20mm graded crushed stone aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs ,complete all as specified and directed.

Material and Labour for form work to sides of concrete foundation, footings, base of columns etc with rough finished flat surfaces of concrete complete all as specified and directed.

Material and Labour for form work to sides of concrete of columns pillars, posts , struts, pipers etc with rough finished square/rectangular surfaces of concrete complete all as specified and directed.

Material and Labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc, complete all as specified and directed.

Material and Labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, andings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc, complete all as specified and directed.

M&L, Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirmaing to TMT bars, complete all as specified and directed.

M&L, mild steel bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirming to TMT bars, complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in Cement Plaster 1:6 and finished the surface fair and even complete all as specified and directed.

Rendering 15 mm thick cement plaster 1:4, on stone masonry surfaces other than fair face of brick work or on one side lathing and finishing the surface even and smooth w/o using extra cement.

75mm thick cement concrete type C-2, 1:3:6 (using 40mm graded aggregate) as in plinth protection finished fair & even without using extra cement, complete all as specified.

M&L Hard core of broken stone or boulders of guage n. exc 63mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

75mm thick , Plain cement concrete, M-10 (Nominal Mix), Type C-2 (using 40mm graded crushed stone aggregates) as in sub base of floor and path etc, complete all as specified and directed.

25 mm thick, plain cement concrete, M-15 (Nominal Mix), type B-0 (using 12.5 mm graded crushed stone aggregates) as in floors finished rough surface to receive floor finishes, complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of mortar in cement plaster 1:4, complete all as specified.

Glazed ceramic coloured tiles 300 mm x 200 mm x 7 mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:4 to receive tiles, complete all as specified.

Pressed steel framessize 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc., complete, as specified,supplied and fixed complete all as specified.

2nd class HW rail and style Plain framed, panelled shutter (two panel) Thickness ofshutters 35mm with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated 2nd class HW rail and style 35mm complete all as specified and directed.

Plain cement concrete, M-15 (Nominal mix), type B-0 (Using 12.5mm graded stone aggregates) as in filling of steel chowkats or frames, complete all as specified and as directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supply & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ' C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified.

150mm long aluminium handle, cast type, anodised complete all as specified and directed.

Aluminium, anodised, barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed.

Mild steel cold rolled Butt hinges, medium weight, 100 mm long, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed size 250mm complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of white wash, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceiling and applying two coats of white wash, to ceiling, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint to walls, complete all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as spfd and directed.

Preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as spfd and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

3mm thick figured glass pin head type and glazing with oil putty in squares n.exc. 0.50 sqm in each pane, complete all as spfd and directed.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, complete all as specified.

Steel tubes, 20 mm bore, galvanised, 'medium grade' with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor incl cutting chases for concealed work etc, complete all as specified and directed.

Steel tubes, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

Bib tap, cast copper alloy with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe, 15 mm bore, complete all as specified and directed.

Pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe 15 mm bore, complete all as specified and directed.

Angle valve cast copper alloy fancy type, chromium plated screwed down for high pressure screwed down for 15mm bore with crutch or butterfly handle both ends screwed for iron pipe or union etc, fixed in repair all as specified.

20mm bore stop valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union , complete all as specified and directed.

Vitreous china, wash hand basin, (white) of size 550mmx400mm including brass CP waste coupling 32mm dia with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends (fixed in repair), complete all as specified and directed.

Vitreous china coloured wash down water closet pan (Padestal Pattern), including connection to flush pipe, 'P' or 'S' trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device (excluding flushing cistern and flush pipe), complete all as specified and directed.

Jet for pedestal pan, chromium plated of standard size complete all as specified and as directed.

10 ltr capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32mm dia PVC flushing pipe and 15mm dia 450mm long PVC connection with CP brass coupling nuts and PVC washer at both ends complete all as spfd and directed.

Vitreous China urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brassscrews, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

Tubular towel rail, 20mm dia, 60 cm long, CP with a pair of brackets, fixed to wall with CP brass screw and PVC rowl plugs ,complete all as spfd and directed.

CP Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified and directed.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L Salt glazed stone ware drain pipes grade 'A' of 150mm bore laid in trenches and jointed as specified.

SCHEDULE 'A' PART-II (External water supply works) Excavation in trenches, not exceeding 1.5m wide and not exc 1.5m in depth and getting out in hard/dense soil, for removing/laying pipes, complete all as specified and as directed.

Returning, filling in, (soil) including spreading, levelling, watering and well ramming in layers not exc. 25cm thick in any type of soil, complete all as specified and directed.

Removal of excavated materials (soil) to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5m above the starting point, complete all as specified and directed.

Taking up or down GI tubing including all fittings from trenches , wall, floor etc including cleaning for refixing or removing to store for safe custody/ reuse or disposal under schedule of credit of size 20mm bore complete all as specified and directed.

All as per the description of serial item No. 61 here -in-before but for of size 25mm bore, complete all as specified and directed.

All as per the description of serial item No. 61 here -in-before but for of size 40mm bore, complete all as specified and directed.

All as per the description of serial item No. 61 here -in-before but for of size 50mm bore, complete all as specified and directed.

All as per the description of serial item No. 61 here -in-before but for of size 80mm bore, complete all as specified and directed.

All as per the description of serial item No. 61 here -in-before but for of size 100mm bore, complete all as specified and directed.

Dismantling, taking up CI/DI water main 100mm bore including with all fitting with spigot and socket, ends / flanged ends including taking out lead joints and rubber joints, removing the pipe from site complete all as specified .

All as per the description of serial item No. 67 here -in-before but for of size 150 mm bore, complete all as specified and directed.

All as per the description of serial item No. 67 here -in-before but for of size 200 mm bore, complete all as specified and directed.

Dismantling and taking down unserviceable cast iron sluice valve 80 to 250mm bore, including jointing material and removing from site, complete all as specified and directed.

M&L Galvanised iron water tubing 20 mm bore, medium grade with all fittings such as bends, elbows, tees, short pieces, connector with (ISI marked), check nuts, caps, plugs and union etc and laying in trenches/floor, complete all as specified and directed. Note: (a) Earth work shall be measured & paid under relevant item. (b) The cost of new fitting alongwith cutting, threading as required shall be deemed to be included in the rate quoted.

All as per the description of serial item No. 71 here -in-before but for of size 25 mm bore, complete all as specified and directed.

All as per the description of serial item No. 71 here -in-before but for of size 40 mm bore, complete all as specified and directed.

All as per the description of serial item No. 71 here -in-before but for of size 50 mm bore, complete all as specified and directed.

All as per the description of serial item No. 71 here -in-before but for of size 80 mm bore, complete all as specified and directed.

All as per the description of serial item No. 71 here -in-before but for of size 100 mm bore, complete all as specified and directed.

M&L Ductile iron pipe (Conforming to IS: 8329) with spigot and socket ends of bore 100mm special class K-9 suitable for tyton joint including jointing material/ joints laid in trenches complete all as specified and directed.

M&L Ductile iron pipe (Conforming to IS: 8329) with spigot and socket ends of bore 150mm special class K-9 suitable for tyton joint including jointing material/ joints laid in trenches complete all as specified and directed.

M&L Ductile iron pipe (Conforming to IS: 8329) with spigot and socket ends of bore 200mm special class K-9 suitable for tyton joint including jointing material/ joints laid in trenches complete all as specified and directed.

Ductile iron pipe (Conforming to IS: 8329) with flanged ends and equally drilled holes of bore 150mm special class K-9 with jointing material i.e. nuts, bolts, washers, gasket of suitable size etc, laid in trenches complete all as specified and directed.

M&L for CI /DI fittings any type such as bends (any type radious and angles), reducers ,Tees, Y pieces, collars caps, plugs and straight connecting pieces upto 150 mm dia complete all as specified and directed.

M&L for CI/DI fittings any type such as bends (any type radious and angles), reducers ,Tees, Y pieces, collars caps, plugs and straight connecting pieces upto 200 to 300mm dia complete all as specified and directed.

S&F Cast iron sluice valve long body type, both ends flanged and drilled, of size 80mm bore, (ISI marked) conforming to IS-14846 -2000 with pressure rating of PN-1.0 with stainless steel spindle and iron wheel head including jointing material such as nuts, bolts, washers and rubber gasket etc, complete all as specified and directed.

All as per the description of serial item No. 83 here -in-before but of size 100 mm bore, complete all as specified and directed.

All as per the description of serial item No. 83 here -in-before but of size 150 mm bore, complete all as specified and directed.

All as per the description of serial item No. 83 here -in-before but of size 200 mm bore, complete all as specified and directed.

All as per the description of serial item No. 83 here -in-before but of size 250 mm bore, complete all as specified and directed.

Supply and fix in repairs gun metal gate valves with iron wheel head screwed both ends for GI pipe of size 20mm complete all as specified and directed.

All as per ser item No. 88 here -in-before but of size 25 mm bore, complete all as specified and directed.

All as per the description of serial item No. 88 here -in-before but of size 40 mm bore, complete all as specified and directed.

All as per the description of serial item No. 88 here -in-before but of size 50 mm bore, complete all as specified and directed.

Cutting of existing cast iron pipe in position and reducing to required length for repair of blockage or insertion of new CI fittings such as collars branches Tees etc for the following sizes complete including necessary earth work of size 200mm bore complete all as specified and directed.

All as per the description of serial item No. 92 here -in-before but for of size 150 mm dia, complete all as specified and directed.

All as per the description of serial item No. 92 here -in-before but for of size 100 mm dia, complete all as specified and directed.

Run lead joints to cast iron spigot and socket pipe (water main) and fittings including burning of old lead joint for 100 mm bore, complete all as specified and directed.

Run lead joints to cast iron spigot and socket pipe (water main) and fittings including burning of old lead joint for 150 mm bore, complete all as specified and directed.

Run lead joints to cast iron spigot and socket pipe (water main) and fittings including burning of old lead joint for 200 mm bore, complete all as specified and directed.

Brick masonry valve pit of size 60X60X60cm (Internal dimensions of chamber) built in Cement Mortar 1:6, Plain cement concrete, M-10 (Nominal mix) type C-2 (using 40 mm graded crushed stone aggregates) as in foundation filling and mass concreting and including 15mm thick plastering internally with cement mortar 1:6 and flush pointing externally as the work proceeds in same mortar and Plain cement concrete, M-15 (Nominal mix), type B-1, (using 20mm graded crushed stone aggregates) as in coping complete. 3.15 mm thick MS sheet cover, handle, locking arrangement including provision of angle iron frame 40x40x6 mm for cover and 2 foot steps made out of MS 16 mm dia round bars, wash out pipe made out of GI pipe medium grade, 50 mm dia upto 1 metre length, earth work in any type of soil including removal to a distance not exceeding 50 metre and painting steel surface with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

All as per the description of serial item No. 98 here -in-before but of size 90x90x90cm, complete all as specified and directed.

Plain cement concrete, M-15 (Nominal mix), type B-2 ( 1 : 2: 4), (using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete, complete all as specified and directed.

Dismantaling of MS sheet of any size and thickness from the cover of existing PS tank (approx area- 47.0 sqm) including un screwing nuts, bolt/washer and refixing the same after repair of PS Tank at the height of 5 feet staging above GL complete with jointing materials all as specified and directed.

Material and labour for replacement of angle iron bracing of size and thickness as per existing inside the PS steel tank including making necessary arrangement for holding of surrounding plates and bracing, cutting of gusset plates to required size and shape & angle for jointing with bracings by drilling holes welding of web piece with gusset plate where ever required after making proper shape etc complete at the height of 5 feet staging all as specified and directed.

M&L for repair to leakage of PS tank by means of welding / using jointing materials or replacement of angle iron bracing inside the PS tank for support to PS plate complete all as specified and directed. Note:- Angle iron bracing used to support the PS plate will be measured and paid separately.

M&L for preparation of steel surface and applying two coats of black bituminous paint (Drinking water Grade) over a coat of red oxide primer on internal surface of PS tank at the height of 5 feet above GL complete all as spefied and directed.

SCHEDULE 'A' PART-III (Provn of 12 Nos geysers of 298 Fd Regt and Internal Electrification works in bldg No M-37 of B Coy Office) Point wiring with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable 1100 volts grade single core conforming to IS-694-1990 and including one run of continous earth wire to common earth and connected to earth with 1.5 Sqmm PVC (FRLS) insulated unsheathed multi stranded copper conductor cable draw in & incl PVC surface casing 'N' capping double lock type to be fixed with the help of rawal plugs & screws incl all fittings such as Tee, connector pieces, L-junction etc on joints including CI/MS/PVC sunk boxes for mounting switches, sockets, regulators etc with 3 mm thick plastic laminated sheet cover of adequate size for one light/fan/bell point controlled by one switch and making good disturbed surfaces with CM (1:4) to match with the existing surface complete all as specified and directed.

Supply and fixing switch piano flush button types 5 Amp single pole one way complete as specified.

Ceiling rose 3 terminal bakelite 65mm x50mm surface type complete all as specified and directed.

Supply and fixing batton holder with LED Bulb 7 W complete all as Specified.

S&F LED batten with LED rod complete T-8, 1x18 W including provn of flexible cable 3 core, 23/.0076 from ceiling rose to connector complete all as specified and directed.

Supply & fixing exhaust fans AC single phase 230V of size 250 mm (PVC body) with louvers shutter including making/repairing hole in brick/stone wall as per site reqmt and making good disturbed surfaces, complete all as specified and directed.

S&F sheet metal enclosures distribution board single pole and natural 2 way with 200 Amps rated bus bar 240 V, single door type complete all as specified and directed.

Supply and fix MCB SPN 240 volts, 10kA, 50 Hz of capacity 40-63 Amps 'C' series all as specified and directed.

M&L for 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1m apart including 4mm dia suspension GI wire with stranded conductor 4 sqmm twin core cable flat or circular including taking down old unserviceable cable and stacking at site, complete all as specified.

Material and labour for house service bracket (hook type) complete with 3m long GI pipe 40mm dia, medium grade , 2 Nos, 90 degree, MS hook and stay or gay on the wall by grouting cement mortar and make good on all disturbed surfaces complete all as specified and directed.

Earthing with galvanized steel earth plate electrode 60cmx60cmx6mm thick, buried directly in ground (earth pit less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr deep below normal ground level, connected to 4mm dia galvanized iron wire as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel complete with 15mm dia light grade protection pipe, 20mm dia GI light grade watering pipe with funnel including char coal dust, salt, PCC 1:2:4 in pit with precast RCC M-15 cover reinforced with XPM not less then 4.00 Kg per sqm including necessary earth work in any type of soil, removal of surplus soil to a distance not exc 50m, returning filling in complete as shown in electrical plate No 3 of SSR Part-I (2009), and connected to earthing test point all as specified or indicated, including testing on completion. NOTE: The rates for earthing includes the cost of earth lead and protection pipe upto 7.50m length.

Supply , fixing , connecting and testing electric water heater storage type 25 ltrs capacity complete with stainless steel water tank and all safety devices such as thermostate, pressure release valve , NRV and air release valve complete all as specified & directed.

Supply and fixing PVC water connection pipe 15mm size with PTMT nuts of length 450mm for inlet & outlet connection (cold & hot water ) complete all as specified.

Supply and fix GI water tubing medium grade 15mm bore with all fittings fixed in walls/Floor complete all as specified and directed.

Supply and fix 15mm bore stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union etc complete all as specified and directed.

Supply and fix bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified.

M&L for cutting of existing GI pipe in position for taking down addition alteration or for repair of GI pipe of size 20mm dia bore complete all as specified and directed.

Point wiring with 2.5 sqmm PVC (FRLS) insulated unsheathed multistranded copper conductor cable 1100 volts grade single core conforming to IS-694-1990 and including one run of continous earth wire to common earth and connected to earth with 2.5 sqmm PVC (FRLS) insulated unsheathed multistranded copper conductor cable drawn in PVC casing & capping incl sunk box for mounting switches/ sockets with 3mm thick plastic laminated sheet cover of adequate size for 3 pin switch socket outlet 15/20 amps on independent board and making good to distrubed surface with CM (1:4) to match with the existing surface complete all as specified and directed.

Supply and fix switch socket combination 2 in 1, 3 pin 5 and 15 amps flush type universal with indicator complete all as specified and directed.

M/S THAKUR ENTERPRISES

M/S MALHI CONSTRUCTIONS