REPAIR/REPLACEMENT TO FLOOR, JOINARY, SAINITARY IN BLDG NO P-7, EOL BLDG, AUDITORIUM(BOTH) NAG BLDG, SECURITY OFFICE, TDC BLDG, CHETAK BLDG, WET CANTEEN P-9, KOTE BLDG, P-100 P-101 P-102 P-24 RAV SCHOOL IN TECH AREA AT IRDE UNDER GE(I) RND DEHRADUN

Amount

Taking down chowkats or frame of any description n.exc. 1.5 Sqm each (without taking off shutters from the frames) & remove off the premises complete all as specified and directed.

Taking down chowkats or frame of any description exc 1.5 Sqm each and n.exc 4Sqm (without taking off shutters from the frames) & remove off the premises complete all as specified and directed.

Taking down shutter exc. 1 Sqm and n.exc 2 Sqm each of any description. complete all as specified and directed.

Taking down shutter exc. 1 Sqm and n.exc 2 Sqm each and refixing the same opening after resecuring or easing and adjusting shutters of any description. complete all as specified and directed.

Taking down shutter exc. 2 Sqm each and refixing the same opening after resecuring or easing and adjusting shutters of any description. complete all as specified and directed.

Dismentling of wall and ceiling boards/ Alca panel /fibre/ pvc Board/PVC sheet panelling pulp, insulation etc or insulation boards/ slabs/blankets any thickness incl cover fillets, fittings, complete all as specified and directed

S&F 3mm thick Alka Pannel board as in flashing complete with fixing arrangement as per manufacter direction & complete all as specified and directed.

S&F for 4 mm thick Alca Pannel pattern Letter writing nexc 30 Cm in height complete with fixing arrangement as per manufacter direction, Complete all as specified and directed

S&F in repair 24 mm thick solid factory made PVC board for cup board /cabinate shutter with one side prelaminated decorative lamination suitable fixed with & including stainless screws, matching colured edge bonding tape to cover all edges , Magnetic catcher all as per specification & and manufacture instruction complete all as specified & directed.

M/L for repairing to existing aluminium doors of any size by straightening of frame / shutter, replacing the detoriated member with new, replacing the broken / non funcional hinges with new, replacing decayed rubber gasket with new, replacing the broken glass pane of any size with new 5.00mm thick tinted glass, replacing unserviceable handle, tower bolt, lock, floor spring, foundation box with governing pivot, top pivot, peg stay etc with new and including taking down and at same place after making the door / window smooth functional complete all as specified and directed.and directed.

M/L for repairing to existing aluminium window of any size by straightening of frame / shutter, replacing the detoriated member with new, replacing the broken / non funcional hinges with new, replacing decayed rubber gasket with new, replacing the broken glass pane of any size with new 5.00mm thick tinted glass, replacing unserviceable handle, tower bolt, lock, floor spring, foundation box with governing pivot, top pivot, peg stay etc with new and including taking down and at same place after making the door / window smooth functional complete all as specified and directed.

M& L for preparation of newly plasted wall surfaces and appltying three coats of texture (Super fine) finished painting with the following process the surfaces should be completely dry and free from loose particles including preparing the surface with emry paper 180 nos and wipring clean and applying one coat of primer and allow drying for 6 to 8 hours then smoothen the surface by filling dints with thin coat of acrylie wall putty after drying for 4 to 6 hours and preparing the surface with emry paper and clean and applying another coat of primer and allow drying for 6 to 8 hours and then emulsion 1 Ltr with 500 ml water and applying with brush follwed by rolling with sponge roller or filter roller, applying three coat with brush and roller with and interval of 3 to 4 hours between successive coat all as per manufactures instruction complete all as specified and directed

M&L for E-board false ceiling consisting of powder coated GI wall angle, main T and cross T of 25mmX 25 mm X 1.40 mm thick grid frame work, joist, angle/ Tee as directed and mild steel wire hook not less than 6 mm dia with arrangement for adjusting height of ceiling and including provn of 4 mm thick E- Classic board in pannelof size 600X600mm with necessary off cut including taking down and refixing of Electric fitting carefully complete all as specified and directed.

M& L for 10 mm thick decorative plaster of paris false ceiling bending/Moulding as required shape with two coats of plastic emulsion paint over a coat of primer on decorated surfaces of ceiling including 26 gauge galvanished iron sheet 'C' shaped main member @750 mm C/C cross member 'U' shaped @450 mm c/c and perimeter of 'C' shaped GI wire mesh having aperture 6.5 mm with 26 gauge wire GI wire 6mm dia or more or FI 40x4mm thick for hanging arrangement with MS suspension.fastner spaced @ 450mm c/c in both direction the 'C' member shall be made out of not less than 90mm wide GI sheet strip and side tray as required of approximate size 3.5 Mtr height as required at site complete all as specified and directed.

M&L PVC SHEET WALL PANELLING of thickness 5mm consisting of panels of desired size stuck on inner frame work of 50mm wide strips of 5mm thick prelam PVC sheet. The panel & strips shall be of 600 kg / cum density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. A groove of 2mm may be left at the joint of two panels for aesthetic looks. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a U Channel at top, bottom and side edges and strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement complete all as specified and directed ( Note- Including all nesscesary fittings and scafolding for heighted site)

S&F powder coated aluminium sliding window three track with two glass shutters and one wire gauge shutter, aluminium powder coated section aluminium cleat, PVC track, bearing, handle locking arangement, rubber beading etc complte fittings as approved. Note Size of aluminium section shall be under :- (i) Three track top and vertical - Jindal or equivalent main-2010 section No 20621 or equivalent (ii) Three track bottom- Jindal or equivalent main-2010 section No 20620 or equivalent (iii) Shutter vertical section- Jindal or equivalent main- 2010 Section 20606 or equivalent (iv) Shutter top and bottom - Jindal or equivalent main-2010 Section 20604 or equivalent (v) Shutter vertical middle (interlock) - Jindal or equivalent main-2010 section 20605 or equivalent

S&F powder coated aluminium sliding window two track with two glass shutters and one wire gauge shutter, aluminium powder coated section aluminium cleat, PVC track, bearing, handle locking arangement, rubber beading etc complte fittings as approved. Note Size of aluminium section shall be under :- (i) Two track top and vertical - Jindal or equivalent main-2010 section No 20830 or equivalent (ii) Two track bottom- Jindal or equivalent main-2010 section No 208829 or equivalent (iii) Shutter vertical section- Jindal or equivalent main- 2010 Section 20606 or equivalent (iv) Shutter top and bottom - Jindal or equivalent main-2010 Section 20604 or equivalent (v) Shutter vertical middle (interlock) - Jindal or equivalent main-2010 section 20605 or equivalent

S&F in repair venetian blind coloured powder coated 35mm wide and 1 mm thick Aluminium alloy blades with opening and closing arrangment including aluminium hanging channel at top with sliding wheel/ring including pulling rope in both side and necessary accessories complete all as specified and directed.

M&L for taking down/dismantling of existing roof treatment of any description such as PCC Padding/ Coba treatment/ mud phuska/Lime conc terracing including screed bed etc, Hessian base felt/tar felt etc. (any type and thickness) complete all as specified & directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on roof surface including mixed with WPC as per manufacturer's instruction's and finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid for separately as supply only under respectiveitem of sch 'A'.

M & L for water proofing treatment on roof slab including picking ,sweeping ,clean and washing down with water to remove dust & providing water proofing treatment described as under :- (a) Surface preparation and treating construction joints, filling of honey combs,preparation of coving ( if required ) with Asian paints smartcare Repair Mortor and Asian Smartcare General purpose Grout of Asian paint or equivalent product of THERMAX / FOSROC . (b) Cleaning the surface and appling Asian PU Magnum primer Resin & hardner of Make Asian paints or eqivalent product of THERMAX / FOSROC on the cleaned surface. (c) Appling Asian Smartcare PU Magnum of Make Asian paints in Two ( 2 ) layers ( PU Magnum per coat should be minimum of 600 gms per Square meter or equivalent product of THERMAX / FOSROC. ( d). Ponding test of 72 Hrs and no leakage/ seepage observed. Any rectification to be done at the cost of contractor repeating above stepsof application. (e) . The work shall be carried out complete as per manufacturer's specification and application methodolgy. (f) . Execution to be done with authorised applicator of the manufacturer and company bank gurantee to be given by the contractor after completion of water proofing work befor payment. work will be executed in Smart Assurance System of manufacturer company of Asian/ Epoxy/ Polymer chemicals.

S&F MS Square or rolled section as in framing for cladding,glazing, panel framing and the like fixed with angle cleats and connecting plates etc Fe-410-W (gde-E250) Quality B complete all as specified and directed

S&F 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by the Engineer-in-Charge

S&F for 40mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer All as specifed and directed.

S&F factoty made 100% solid Wood Plastic composite (WPC) door frame of size 90mm x 45 mm made from wood plastic composite ( Single extruded Process ) materials with density 780 Kg/cum should be water proof,termite proof, fire retardant & having good screws holding capacity , complete all as specified and directed.

S&F factory made solid PVC moulded door shutters 28 to 30mm thick stiles), with 2,4 or 6 raised panel design with 2mm thick moulded PVC sheet on back face, with wood free EPS, Supplying and fixing in frame at site as per specifiecation & drawing shown in section 8 of SSR part-II complete all as directed.

S&F factory made solid PVC flush shutters 32 mm thick ,made from co extruded three layer rigid PVC Sheet ( Single Extruded ) with density not less than 600 Kg/ Cum, outer layer ( 0.80-1 mm ) thick should be of rigid PVC with density of not less than 1400 Kg/ Cum Supplying and fixing in frame at site as per specifiecation & manufacture Instruction complete all as directed.

S&F 150mm size aluminium, anodised barrel tower bolt of extruded section.

S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy.

S&F100mm size, butt hinges, medium weight, cold rolled mild steel.

S&F 150mm size extruded aluminium alloy handles, fabricated type.

Dismantling aluminium or wooden partition work or asbestos cement sheet partition or boarding of any description , fixed in position with nails. Complete all as specified and directed.

S&F Powder coated aluminium frame for doors,or partition including aluminium beading, hinges of required size,jointing cleats, screws, dash,fastners,plug for fixing with wall, columns etc complete all as specified.

S&F Powder Coated aluminium door shutters, aluminium section weighing 0.55kg/m including necessary jointing cleats/ glazing clips, rubber neoprene packing, handles 2 Nos in each door , locking arrangment, aluminium snap beading screw etc, complete all as specified and directed.

S&F repair Diamond Aluminium wiremess fixed to aluminium frame of window etc all as specified and directed .

S&F 12 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice laminations,fixed with screw to timber frame work and sealing edges of board with PVC beading by chemical adhesive complete all as specified and directed.

M&L for 4.8 mm thick Frosted sheet glass ordinary quality in panes not exc 0.50 sqm each fixed with & including rubber gasket in aluminium frame work complete all as specified and directed.

M&L for 4.8 mm thick Frosted sheet glass ordinary quality in panes exc 0.50 sqm each fixed with & including rubber gasket in aluminium frame work complete all as specified and directed.

M&L for 4.8 mm thick sheet glass ordinary quality in panes not exc 0.50 sqm each fixed with & including rubber gasket in aluminium frame work complete all as specified and directed.

M&L for 4.8 mm thick sheet glass ordinary quality in panes exc 0.50 sqm each fixed with & including rubber gasket in aluminium frame work complete all as specified and directed.

M&L for 5.5 mm thick sheet glass ordinary quality in panes exc 0.50 sqm each fixed with & including rubber gasket in aluminium frame work complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame incl punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

M&L for 4mm thick sheet figured glass, pin headed type and glazing with oil putty in square n exc 0.5 Sqm in each pane.

M&L for 12 mm thick Toughened glass, Ist quality in square or rectangular with fixing arrangement for Multistorey bldg above ground floor and upto 4th storey with scafolding arrangments complete all as specified and directed

M&L for 4mm thick sheet glass, ordinary quality and glazing with oil putty in square or rectangular for Multistorey bldg above ground floor and upto 4th storey with scafolding arrangments complete all as specified and directed

Taking down existing double action floor spring hydraulically regulated and Refixing only after necessary repairs, oiling & greasing etc in proper position with and including proper screw complete all as specified and directed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified.

S&F in repair aluminium (die cast) body door closer hydraulically regulated, designation No.3 universal type, suitable for doors shutters up to 1000 mm in width and of weight between 61 to 80 Kg and fixed complete allas specified and directed.

S&F in repairs mortice lock, vertical type of size 100 mm with brass body 2 lever complete all as specified.

S&F in repairs mortice lock, vertical type of size 75 mm with brass body 2 lever complete all as specified.

Roughening of old concrete floor by picking,sweeping clean and washing down with water toremove dust etc complete all as specified and directed.

M&L for 2.50 mm thick homogenoues PVC tiles/ sheets,laminated plain coloured/textured , marbled mosaic or mottled finish, laid with approved rubber based adhesive in floors complete all as specified and directed.

Demolition of brick or stone boulder masonary built in cement mortar or cement lime mortar including all quions, arches,pillars etc but excluding ashlar facings,dressed stone work s and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight on plan built in cement mortar 1:6 complete all as specifed and directed

Taking down cement or cement lime plaster of any description including racking out joints, hacking for keys , scrubing down with water etc, complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of concrete /brick surface in cement mortar 1:6 finished fair and even as in wall complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of concrete/brick surfaces in cement mortar 1:4 mixed with water proofing compound as per manufacturer's instruction, finished fair and even without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid for seprately as supply only under respective item of sch A.

Supply only integral water proofing compound ISI marked complete all as specified and directed..

M&L two coat of oil bound distemper of required tint on newly plastered surfaces of wall after prepration of surface and over a coat of chalk whiting complete all as specified and directed

M & L for preparation of newly plastered surface and applying two coat of cement base paint over a coat of suitable primer on walls complete all as specified.

M&L for preparing old surfaces of walls plastered or un-plastered by brooming down with steel or wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , washing rubbing down and stopping of distempered and painted surface & removing all nails and making good holes,cracks etc complete by necessary putty and make the surface smooth by rubbing with sand papers etc and applying one coat of distemper oil emulsion on old prepared surfaces of walls complete all as specified and directed.

M&L for preparing old surfaces of walls plastered or un-plastered by complete removal of existing treatment by brooming down with steel or wire brush and scraping down smoke soot, moulds moss & efflorescent salt and trading oil and greasy spots , distempered and painted surface & removing all vegetation growth, nails and making good holes,cracks etc complete by necessary putty & applying of Birla/JK white wall putty approx 1 mm thick as per manufacturer's instruction on existing prepared surface and make the surface smooth by rubbing with sand papers etc and applying Two coat of cement base paint on old prepared surfaces of walls up to four story buildings of walls including scaffolding and all necessary items complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof coverings.

S&F prepainted galvalume(55% aluminium+45% zinc) steel sheet as in roofing 0.50 mm thick(total coated thickness)confirming to AS-1397/ASTM A-792 having tensile strength of 550 Mpa as in roofing,purlingwith self drilling metal coated screw of appropriate size self taping bolt and fixed as per manufactures instruction complete all as specified. sheet shall be laid with one corrugation side lap and end lapminimum 150mm in slope all as per manufactures instruction along with wind ties complete all as specified and directed .

S&F prepainted plain galvalume(55% aluminium+45% zinc) steel sheet as in roofing 0.50 mm thick(total coated thickness)confirming to AS-1397/ASTM A-792 having tensile strength of 550 Mpa as in gutter,ridges , purling with self drilling metal coated screw of appropriate size self taping bolt and fixed as per manufactures instruction complete all as specified. sheet shall be laid with one corrugation side lap and end lapminimum 150mm in slope all as per manufactures instruction along with wind ties complete all as specified and directed

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing), removing debrish and rubbish off the premises and stacking serviceable tiles .

M&L for non-skid coloured ceramic tiles first quality (of approved class, colour and design/shade) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0. 06 sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including 15 mm thick cement screed bed in cement mortar 1:6 for laying floor finishes. complete all as specified and directed

M&L for non skid ceramic coloured tiles 7 to 8 mm thick Ist Quality approved coloured desigen/shade(square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of size 300x200x7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of size 350x250x7mm/600 x 350 x 7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed.

M&L vitrified coloured tiles 10 mm thick of premium quality colour and pattern as approved (square/rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick cement screed bed in cement mortar 1:6 for laying floor finishes. complete all as specified and directed.

M&L for full body Glazed vitrified coloured tiles 10 mm thick of premium quality colour and pattern as approved (square/rectangular) area of each tiles exceeding .38 sqm but not exceeding 1.00 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick cement screed bed in cement mortar 1:6 for laying floor finishes. complete all as specified and directed.

M&L glazed vitrified coloured tiles 10 mm thick of premium quality colour and pattern as approved (square/rectangular) area of each tiles exceeding .18 sqm but not exceeding 0.38 sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including 10 mm thick rendering in cement mortar (1:4), rough finish to receive the tiles complete all as specified &directed

M&L full body Glazed vitrified coloured tiles 10 mm thick of premium quality colour and pattern as approved (square/rectangular) area of each tiles exceeding .38 sqm but not exceeding 1.00 sqm, in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including 10 mm thick rendering in cement mortar (1:4), rough finish to receive the tiles complete all as specified &directed

S&F Brass handles 100mm size, cast type, polished bright as approved by Engr in Charge complete all as specified and directed

S&F 40 mm dia, brass, knobs for cupboard fixed with nut, screw and washer of mild steel, bright finised complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm complete all as specified and directed.

S&F Brass Locks 2 levers, cupboard, grade I, size 50 mm complete all as specifed and directed.

S&F 150mm size aluminium, anodised barrel tower bolt of extruded section.

M&L for post construction ATT along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre incl drilling and plugging holes etc in apron complete

M & L for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors

M&L post construction ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.50 litres/hole by driling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete

M&L for greasing and oiling in old rolling shutters (area exceeding 10.00 sqm of each shutter) of each parts i.e guide channels, cranks, springs, gearboxt and locking arrangement etc. with and including repairs as required for smooth functining of rolling shutter complete all as specified and directed.

M&L for greasing and oiling in old rolling shutters (area not exceeding 10.00 sqm of each shutter) of each parts i.e guide channels, cranks, springs, gearboxt and locking arrangement etc. with and including repairs as required for smooth functining of rolling shutter complite all as specified and directed.

Taking down carefully unservicable ball bearing from rolling shutters and S&F ball bearing heavy duty as required size at approprite place, match the existing of gear operated type rolling shutter complite all as specified and directed.

Taking down carefully unservicable spring from rolling shutters and S&F new spring heavy duty as required size at approprite place, match the existing of gear operated type rolling shutter complite all as specified and directed.

Taking down carefully unservicable safty lever mild steel lock any type from rolling shutters and S&F new safty lever mild steel lock 4 lever heavy duty as required size at approprite place, match the existing of gear operated type rolling shutter complite all as specified and directed.

S&F in repair steel rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp & staple & one shop coat of primer; erected in position as indicated, complete; push pull or manual type Thickness of laths 1.00 mm complete all as specified and directed

S&F in repair steel rolling shutters, gear operated type with bevel gear box and crank handle, ball bearing, as specified including top cover, anchoring rod, hasp & staple & one shop coat of primer; erected in position as indicated, complete; push pull or manual type Thickness of laths 1.00 mm complete all as specified and directed

Extra for wicket door including a 4 lever mild steel safety lock, lockable from both inside and outside (area of wicket door to be only measured) complete all as specified and directed

M/L for taking down existing steel window Z section shutter by cutting projected type MS hinges and refixing/ irrecting the same by welding box type MS hinge 2 Nos in each shutter including necessary arrangement for works upto 4th story.

S&F for safety lever locks mild steel with 4 leavers for rolling shutters

S&F ball bearing for rolling shutters

M&L for applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth complete all as specified and directed.

Removal of demolished materials to a distance out side defence land at contractor own arrangement complete all as specified and directed .

M&L for Running welding in repairs Thickness of metal to be welded n exc 6mm coplete .

S&F in repairs mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate complete fixed with screw or by welding complete all as specified and directed.

Taking up or down 15 mm steel tubing and connections,including cleaning for refixing or removal to store complete all as specified.

S & F 15 mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors.

M&L for refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 15 mm dia pipes with and including all new fittings complete all as specified and directed. Note:- GI pipe shall be reused after cleaning as retirved from Item No.99 here in above.

Taking up or down 20 mm steel tubing and connections,including cleaning for refixing or removal to store complete all as specified.

S & F 20 mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors.

M&L for Fixing only 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.Note:- GI pipe shall be reused after cleaning as retirved from Item No.102 here in above.

S&F in repair Galvanised sheet water tank covers including nut-bolt, hinges, Hasp & staple, handle etc suitable for water tanks of Cap 500 ltrs to 1000 ltr as per sample kept in AGE office complete all as specified and directed.

Disconnecting & taking down existing water tank of capacity exc 250 liter and not exc. 500 liter and removing from site complte and S&F rotational moulded polyethylene water storage tanks 500 lts capacity (cylindrical vertical with closed top) hoisted with and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part I complete all as specified & directed.

Disconnecting & taking down existing water tank of capacity exc 500 liter and not exc. 1000 liter and removing from site complte and S&F rotational moulded polyethylene water storage tanks 1000 lts capacity (cylindrical vertical with closed top) hoisted with and including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule and fixed in position all as per SSR Part I complete all as specified & directed.

S&F in repair Ball valves 15mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe & fixed. (min. weight 15mm-142 gms)

Dismantling of cast iron, SGSW, PVC or reinforced concrete drain pipes jointed in neat cement mortor and taking out of trenches or floor or wall if required

S&F PVC (SWR) pipe 75 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive and laid in treanches or in floors complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipe 150 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipe 200 mm bore, single socketed , in any length with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&FPVC (SWR) bend/shoe 75 mm dia, any radius as required and jointed with approved adhesive and fixed to floor complete all as specified and directed.

S&F PVC (SWR) Tee, Reducer/junction (single T) equal or unequal 75 mm dia, any radius as required and jointed with approved adhesive and fixed to floor complete all as specified and directed.

S&F PVC (SWR) bend/shoe 110 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) Tee, Reducer/junction (single T) equal or unequal 110 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) bend/shoe 150 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F in repair PVC (SWR) Tee, Reducer/junction (single T) equal or unequal 150 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F PVC (SWR) bend/shoe 200 mm dia, any radius as required and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) floor trap , plain with grating including jointing with solvent cement .

Cleaning and removing all scale and dirt, etc. from tanks and form mouths of circulating pipes, etc., capacity of tank exc 250 & n exc 500 litres including writing date of cleaning on the tank with suitable synthetic enamel paint etc complete all as specified and directed.

Cleaning and removing all scale and dirt, etc. from tanks and form mouths of circulating pipes, etc., capacity of tank exc 500 & n exc 1000 litres including writing date of cleaning on the tank with suitable synthetic enamel paint etc complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

S&F in repairs Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete.

Taking down shutter n.exc 1 Sqm each of any description complete all as specified and directed.

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing , anodised aluminium snap, rubber packing , anodised aluminium snap beading , screws , anodised aluminium fittings such as peg stays 150 mm long (1 No), hinges type B-21 100 mm long (2 No) suitable handle (1 No) complete all as specified and directed.

Amit Associates

Gaur Construction Co