M/o W/s (Two Year Repairing of PVC/C.I./D.I./M.S. Water Line, R/o Sluice Valve and Reflex Valve and S/F Flushing Sluice Valve in Network Sector-130, 162 and Village- Gulavali, Mohiyapur, Yakootpur, Nagla Nagli, Nagli Sakhpur, Rohillapur) Noida.

Cutting road and making good the same i/c supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required of bituminous portion.

Cutting road and making good the same i/c supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri and labour required of water wound macadam.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (Not exceeding 1.5 m in width as we as 10 sqm on plan) including getting out and disposal of excavated earth, lead upto 50 and lift upto 1.5m, as directed by Engineer-in-charge. The contractor has to detect different utilities like sewer line, water supply line, electric cable, telephone cable, gas pipe line etc. using utility detecting machine before start of excavation and shall start excavating only after getting permission of Engineer-in-Charge. All kinds of soil.

Repairing of Existing PVC water line bailing out of water by / Beldar / Deisel Engine, P/F PVC coupler, CID joint etc. complete work as per direction of E/I (But Excluding cost of Excavation filling) 90 mm dia

110 mm dia

140 mm dia

160 mm dia

200 mm dia

250 mm dia

Supply of PVC pipe 6 Kg/cm2 Pressure with required PVC Standard special confirming to IS:4985-2000 with latest amendment Make-Finolex Industries Ltd./Kisan/Superme Industried Ltd. (Rate As Per Comparative Statement Per Rm.) 90 mm dia with coupler @ 6 Kg/Cm2 pressure

110 mm dia with coupler @ 6 Kg/Cm2 pressure

140 mm dia with coupler @ 6 Kg/Cm2 pressure

160 mm dia with coupler @ 6 Kg/Cm2 pressure

200 mm dia with coupler @ 6 Kg/Cm2 pressure

250 mm dia with coupler @ 6 Kg/Cm2 pressure

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth consolidating each deposited layer by ramming & watering, lead upto 50 m and lift upto 1.5 m.

P/F M.S. specials such as Tee, Bend, Collars, Tapers, Gap pieces, including Flange Ends as required, Painting, Cutting, welding as per site requirement of MS pipe thickness etc complete in all respect as per direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : "1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

P/F Sluice Valve shall generally conform to IS 14846 with latest amendment, with length over flanged as per PD of IS 14846 corresponding to BS EN-558 / ISO 5752 Basic series 3 in CI construction having metal seating (IS 318 Gr. LTB 2). With comple component & material of construction following below:- 1 - Body / Door / Dome - Cast Iron IS 210 Gr. FC 260 2 - Spindle - Non rising: Stainless Steel AISI 410 3 - Body seat / Door face - Gun metal : IS 318 Gr. LTB 2 (rings to be press fitted and riveted: no screws allowed) 4 - Rivets - Soft annealed brass 5 - Spindle Nut - Gun metal : IS 318 Gr. LTB 2 6 - Stem Seal - Greased Hemp 7 - Fasteners - Carbon steel 8 - Flange Drilling - IS 1538 Table 4 & 6 9 - PN 1.0 10 - Accessories (400 mm and above) - Ball thrust bearings to be housed above the wet chamber ie. above the gland. Enclosed Spur Gear Box for ease of operation. Air Plug 11 - Painting / Coating - Inside & Outside epoxy liquid coated; DFT minimum 250 micron, shade RAL 5005 / 5015 (BLUE) 12 - Hydro-test-(Open Ended only) (Seat : 10/16 Kg/cm2; Body: 15 / 24 Kg/cm2 13 - Upto 600mm dia Mannual Operated & above 600mm Gear box Make-Indian Valve Pvt. Ltd. (IVC) / Kirloskar Brothers Limited KIRLOSKAR) 150 mm dia

200 mm dia

300 mm dia

P/F Reflex Valve upto 600mm dia shall conform to IS 5312 Part-1 & above to IS 5312 Part-2 with latest amendment, Valves shall be in graded CI with metal to metal (IS 318 Gr. LTB 2) seating, preferably slanted (and not perpendicular) vis-a-vis horizontal axis; SS AISI 410 stub pins & slant seat design. with comple component & material of construction following below:- 1 - Body / Door / Dome - Cast Iron IS 210 Gr. FC 260 2 - Hinge pin (single door) / Stub pin (multidoor type) - SS AISI 410 3 - Seat & Face rings - Gun metal : IS 318 Gr. LTB 2 4 - Rivets - Soft annealed brass 5 - Fasteners - Carbon steel 6 - Flange Drilling - IS 1538 Table 4 & 6 7 - PN 1.0 8 - By - pass arrangement - Optional 9 - Painting / Coating - Inside & Outside epoxy liquid coated; DFT minimum 250 micron, shade RAL 5005 / 5015 (BLUE) 10 - Hydro-test Seat : Seat : 10/16 Kg/cm2; Body: 15 / 24 Kg/cm2 Make-Indian Valve Pvt. Ltd. (IVC) / Kirloskar Brothers Limited KIRLOSKAR) 150 mm dia

200 mm dia

300 mm dia

Repairing of sluice valve with the change of spendle (I.e. S.S. non megnated) flapper adjusting nut & bolts & rod & welding machining of body for fitting the flapper properly complete as per direction of E/I. Kirloskar make. 150 mm dia

200 mm dia

250 mm dia

300 mm dia

400 mm dia

Repairing of reflex valve with the change of flapper sheet i/c new lever, rubber sheet, MS ring, S.S.pin shaft & shaft rubber etc. complete Kirloskar make. 150 mm dia

200 mm dia

250 mm dia

300 mm dia

400 mm dia

Repairing existing AC/CI/DI water line i/c all required materials such as CID joints, rubber packing, nut & bolts, bailling out of water, all labour and T&P i/c cutting of pipe etc. complete work as per direction of E/I. (But exluciding cost of Excavation filling and M.S. Special) 300 mm dia C.I.

Constructing masonry Chamber inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 10.00 90 x 90 x 100 cm.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Hiring of Diesel Engine (Including cst of Diesel, Lubricant & Operator)

Charge of Generator (Including cost Service of operating staff, supply of lubricating oil and diesel also) DG Set / Generator 50 KVA

Hiring of Gas cutting Set With oxygen and LPG Running Time @ 6 Hrs.

Hiring of Welding Set Running Time @ 6 Hrs.

Please Enable Macros to View BoQ information

CAPABILITY STATEMENT

* It is compulsory for the bidder to fill this statement and the bidder must upload only those document that support this statement

Tender Reference No : 48/SM(JAL)-I/ET/2024-25

Not Provided

Name of Tenderer

TOTAL NIT COST OF PROJECT (In Rs.) (In lacs)

Minimum Value

SOLVENCY (Issued within a period of maximum six months).

EXPERIENCE (WITH GOVERNMENT/SEMI- GOVERNEMTN/ PSUs ONLY) completed works during the last 7 years ending last day of the month previous to the one in which applications are invited

NOT QUALIFIED

NOT QUALIFIED

Two similar completed works each costing not less than the amount equal to 60% of estimated cost put to tender

NOT QUALIFIED

One similar completed works costing not less than the amount equal to 80% of estimated cost put to tender

RESULT OF EXPERIENCE

TURNOVER (During the immediate LAST 3 consecutive financial years)

Average annual financial turnover on construction works should be atleast 30% of the estimate cost during the immediate last 3 consecutive financial years.

Required Technical Staff

Required Machinary

Character certificate of Individual/Partners/directors issued from District Magistrate.

Affidavit of Not blacklisted.

Address Proof/ Id.Proof of Individual/partners/directors.

GST Registration certifcate.

Filled in form Capability Statement..

Self declaration affidavit on Rs. 100/- Notarised Stamp paper

Latest ITR

Affidavit of stating No Blood relative in Noida Authority (Regular / Contract)

Certified Copies of relevant pages of following documents:

Note :- If Tender value is Ten lacs & below Ten lacs then above condition no.-02 will not applicable.

RESULT