Addn/altrn for Provn of toilet block near II-8, Provn of hard standing in front of Bldg No II-1 and Special rep to bldg No II-10 (Magazine) at Mily Station Calicut under AGE (I) Cannanore.

Amount

Excavating in trenches n.exc. 1.5m wide and n exc 1.5m in depth for foundation, laying of LT UG cable, pipe, pole, stay etc and n exc 10sqm on plan and getting out in soft/disintegerated rock all as specified and directed.

M & L for plain cement concrete (1:4:8), type D2 using 40 mm graded stone aggregate as in foundation of building, pole, strut, stay etc all as specified and directed.

Returning and filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soil obtained from excavation all as directed

Removing surplus excavated materials (rock) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

S&F 1500mmx450mm bevelled edge mirror 6mm thick of superior quality glass mounted on 6mm thick hard board with wooden moulded frame fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for light shade glazed ceramic tiles 450x350x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

M & L for preparation of newly plastered surfaces of wall and applying a coat of wall primer and two coats of oil emulsion distemper and all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/disintegerated rock and all as specified and as directed.

M&L for MS Rolled sections as in staging for water tank and like including caps, bases, splices etc built from two or more beam or channel including stiffeners, gusset plate etc using Fe 410-w (Gde E -250) quality B all as specified and as directed.

S&F 1000 litres capacity rotational moulded polthylene water storage tanks(cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including 25mm bore brass float valve, high pressure with polythelene ball all as specified in SSR Part I,2009 and directed.

S&F ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule of 50 mm bore dia all as specified and directed.

M&L Cutting the existing PVC/UPVC tubing 50mm bore and inserting UPVC tee of 50x50x50mm for alterations or additions (or lengthening screw on pipe to form connector) if necessarily done in position without taking down all as specified and directed.

S&F for 15mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed to wall/ceiling or on floor all as specified and directed.

S&F for 25mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed to wall/ceiling or on floor all as specified and directed.

S&F for 50mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed to wall/ceiling or on floor all as specified and directed.

Cutting chases on wall of width 30mm and depth 35mm for concealing water tubing 15/20mm dia and making good the surface with plastering in cement mortar 1:4 and finish to match the existing surface etc complete all as directed.

M&L Cutting the existing PVC/UPVC tubing 15mm bore and inserting UPVC tee of 25x15x15mm for alterations or additions (or lengthening screw on pipe to form connector) if necessarily done in position without taking down all as specified and directed.

S&F Vitreous China premium/1st quality Wash down water closet pan, white or ivory (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device all as specified and directed.

S&F PVC valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including low or high density PVC flush pipe all as specified and directed.

S&F mild steel chromium plated Health faucet (ABS body), suitable for 15mm dia pipe with flexible LDPE pipe with jet of 1.25m long on one end and socket joint of 15 mm dia on other end including ABS wall hook complete all as specified and directed.

S&F Vitreous China Wash basin, white, flat back, size 630 x 450 mm, including CI brackets, (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F Soap dish, vitreous China white, approximate size 160 x 160x90 mm all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge

S&F tubular towel rail PTMT, 60cm long between flanges fixed to wall with wooden plugs with chromium plated brass screws all as specified and directed.

M & L PTMT stop valves 15mm bore, any colour high pressure screwed down, screwed for iron pipe or ferrule and complete all as directed.

Supply and fix PVC connecton 60cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

M&L Cutting and screwing existing steel tubing 25mm to 32mm bore for alterations or additions (or lengthening screw on pipe to form connector) if necessarily done in position without taking down all as specified and directed.

S&F 15 mm bore bib taps, PTMT any colour (min weight 15-90gms), high pressure screwed for iron pipe or for PVC pipe or for brass ferrule, all as specified and directed.

S&F 15 mm bore pillar tap, PTMT any colour (min weight 110gms), high pressure screwed for iron pipe or for PVC pipe or for brass ferrule, fixed all as specified and directed.

S & F brass chromium plated shower rose 125 mm dia, with or without swivel joints suitable to 15mm bore pipe complete all as specified and as directed.

S&F vitreous china bowl urinal flat back white 465 x 355 x 265 mm with grating and union for discharge pipe , providing and fixing plugs, bedding urinals against wall in cement mortar1:2, securing urinals plugs with 60mm long brass screws , pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe including M&L of vitreous china bowl urinal partition white 310x700 mm securing urinals plugs with 60mm long brass screws , etc complete all as directed.

S & F urinal spreader of PTMT any colour, 15mm bore (mininmum weight 60gms) complete complete all as specified and as directed.

S&F 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

M&L for 75mm diameter PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/dense soil all as specified and directed.

Excavating in trenches n.exc. 1.5m wide and n exc 1.5m depth for foundation, pipe, pole, stay etc and n exc 10sqm on plan and getting out in hard/dense soil all as specified and directed.

Removing surplus excavated materials (soil) exc 250m and not exceeding 500 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block approved colour, design and pattern confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment as in foot path, lawn, drive ways etc made by table vibratory method using PU mould, including 50mm thick compacted bed of fine sand compacting and proper embedding, laying of paver block into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand all as specified.

Providing, cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) in coping, rounded or chamfered on edges including necessary form works all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on brick or concrete surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for preparation of new plastered wall surfaces and applying two coats of white wash all as specified and directed.

M&L for preparation of new plastered wall surfaces and applying three coats of white wash all as specified and directed.

Dismantling single layer Mangalore pattern tiles in roofing all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

M&L for structural work in tubular sections including special shaped washer, etc, complete using ERW or induction butt welded tubes etc Fe 410W (Gde E-250) quality B all as specified and directed.

Providing, cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge/valley gutter/roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

M&L for preparing surfaces of wood and wood based materials new of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed

M&L for preparation of new or old untreated steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for rendering 15mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for complete removal of existing treatment on surfaces of wall by scrapping down and preparation of surfaces and applying three coats of white wash all as specified and directed.

M&L for complete removal of existing treatment on surfaces of wall by scrapping down, preparation of surfaces and applying two coats of cement base paint over a coat of primer all as specified and as directed.

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer all as specified and as directed.

Dismantling wall and ceiling boards or insulation boards/slabs/blankets any thickness, including cover fillets all as directed.

S & F for anodized aluminium snap grid frame work as in clause No. 10.38 of MES Schedule Part I for false ceiling of size 605 mm x 605mm with supporting hanger comprising of 6 mm GI rod / GI flat 40x3mm, adjusting level with cleats, necessary washers, bolts and nuts for securing frame work to ceiling and to the snap grid complete all as specified and directed

S&F 4 mm thick non asbestos fiber cement building boards inserted to aluminium grid as per manufacturers instructions as in ceilings flat or sloping complete all as specified and directed.

M&L for preparation of new non AC ceiling board or gypsum board ceiling surfaces and applying three coats of white wash all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding(but not backing),removing serviceable tiles and rubbish off the premises all as directed.

M&L 25mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring and finished fair and even all as specified and directed.

M&L forcoloured joint free non-skid ceramic tiles, 7mm to 8mm thick, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

M&L for light shade glazed ceramic tiles 450x350x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

Taking down chowkats with shutters any description n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters any description exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

Taking down door shutters of any description not exceeding 1 Sqm each and refixing the same opening after easing and adjusting and refixing/renewal of builders hardware with screws all as directed.

Taking down door shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each and refixing the same opening after easing and adjusting and refixing/renewal of builders hardware with screws all as directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast including necessary form works all as specified and directed.

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

All as per item No 78 here in before but for with transoms and mullions, with double rebated on the solid frame for fixing double shutters all as specified and directed.

M&L for second class hardwood, panelled shutter 30mm thick (any number of panel) with lock rail and panel of 9mm BWP, 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc; (devide into square sash bar), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

S&F 4mm thick frosted glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane with putty or fixed with beads all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L preparing old treated wooden surfaces of any description over 10 cm width or girth and applying a coat of synthetic enamel painting all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treating back of chowkats,area tarred exc. 0.1 sqm but n.exc 0.5 sqm with tar or coal tar black paint each all as specified and directed.

S&F 200mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F Harrison rails 25mm dia, chromium plated with fixing brackets , stops, rollers etc. all as specified and as directed.

S&F stainless steel butt hinges medium weight; 100mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F stainless steel butt hinges medium weight; 75mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size fixed with stainless steel screws all as specified.

S&F mild steel or cast iron (malleable) casement stays 250mm long with hinged joints and two plates with studs complete all as specified and directed.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

S&F exhaust fan,metallic body AC single phase, 230 V of 300mm sweep, BEE 5 star rated with accessories of Havells or CG or Usha including making suiable size hole to wall and finished as per direction complete including connecting up with 2 core twisted flexible copper conductor 23/0.0076 from ceiling rose to fan, testing and commissioning all as specified and directed.

M&L Point wiring complete with 1.5 Sq mm single core PVC insulated unsheathed copper conductor FRLSH cable multi stranded 1100 Volt grade drawn through and including non metallic rigid PVC conduit, medium grade concealed and fixed to ceiling/roof etc with necessary fixing accessories such as bend elbow socket etc with fixing material including terminal box made out of 1.22mm thick GI sheet concealed in wall covered with bakalite/plastic laminated sheet top cover of 3mm thick cadmium plated screws with cup washer including 1.5Sqmm single core PVC insulated un sheathed copper conductor FRLSH cable multi stranded 1100Volt grade as earth continuity conductor green in colour connected to common earth dolly complete all as specified and as directed for One light/fan/bell point controlled by one switch.

S & F switch piano flush type, single pole, one way, 5 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F PVC ceiling rose 65x50mm size, three terminals, polycarbonate, isolated body including connecting up electrically all as specified and as directed.

JEETH CONSTRUCTION