2-Mandlayukt karyalaya adhishthan Moradabad me vidyutikaran ka karya.

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. (PWD SOR Item NO 501/ 2018)- 120 Sq.mm. x 3-1/2 core 501(o)/2018

70 Sq.mm. x 3-1/2 core 501(m)/2018

50 Sq.mm. x 3-1/2 core 501(l)/2018

S/F of palm or pin type copper tin planted cable socket (lug) to the cable leads etc. comp. (504/2018) 120 Sq.mm. 504(j)/2018

70 Sq.mm. 504(h)/2018

Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 G.I. strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. complete work as per direction of E/I. 725(a)(PWD)SOR-2018

Supply and fixing of horizontal air termination (roof conductor) of 25mm x 3mm G.I. strip, G.I. clamps on surface complete in all respects as approved by Engineer-in-charge.710(PWD)SOR-2018

Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable enteies Electrical control panel with TPN MCCB's (Four pole 36 KA with thermal maganatic release) Switches complete and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters (KVA, P.F., KW etc.) in each phase with touch type selector switches for different reading, instrument fuses, current transfomer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB's shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc. The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2mm. Cubicle type switch board shall be of cat A & B only. Incoming 200 Amp. MCCB-1 No Outgoing (a) 100 Amp. MCCB-2 Nos. (ii) Cat. B. Pannel Cubicle Type each 812/2018

Construction of plinth for generator :- R.C.C. Work with cement approved coarse sand and 2cm. gauge approved stone grit in proportion of 1:2:4 in lintels of doors, windows and sunshades excluding supply of reinforcement and its bending but including its fixing and binding the same with 24 B.W.G.G.I Binding wire and including necessary centering and shuttering etc. and supply of all meterials, labour and T&P etc. required for proper completion of work. Binding wire to be supplied by the contractor free of cost. Including making of drip coarse. Complete work as per direction of E/I. civil SOR 2022 (5.6.1)

Construction of plinth for LT distribution board/Capacitor bank of size 3 X * 1.1 * 0.7mm from G.L. in 1:3:6 sand 1st class B/w including plaster in 1:3 foundation 1:4:8 OBB on top 1:2:4 C.C. (2") including all material labour T&P etc. comp. (P.S.R.)