SPECIAL REPAIR TO BUILDING NO. P-6, P-13, P-83 TO 88 AND P-90 AT AF STN PHALODI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiles from site and rubbish off the premisses complete all as specified and directed.

Demolition of stone slab and tiles of any description or thickness in floors, etc. laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down and refixing shutters exceeding 1.0 Sqm and not exceeding 2.0 Sqm each in same opening after resecuring or easing and adjusting complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) not exceeding 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frames) exceeding 1.5 Sqm but n.exc 4.0 Sqm each complete all as specified and directed.

Dismantling Wall and ceiling boards (Fiber, pulp, insulation,etc) or insulation board/slabs/blankets of any thickness including cone fillets complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames, including punching or drilling out old glazing pins / spring clips, also providing and fixing new ones complete all as specified and directed.

Taking down of cement plaster or cement lime plaster of any description on PCC/stone surface/brick surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking up or down 20mm bore steel water tubing galvanised with connection including cleaning for refixing or removed from site complete all as specified and directed.

Taking up or down 15 mm bore steel water tubing galvanised with connection including cleaning for refixing or removed from site complete all as specified and directed.

Dismantling water tank of capacity exceeding 250 but not exceeding 500 litres complete all as specified and directed.

Dismantling water tank of capacity exceeding 500 but not exceeding 1000 litres complete all as specified and directed.

Demolition of reinforced cement concrete of roofs, floors (other than ground floor), beams, stair cases, landings, slabs, chajjas and similar items including cutting reinforcement to facilitate demolition complete all as specified and directed.

Dismantling cast iron work of any description and any position complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan–necks, etc. including cleaning of or refixing or removed from site complete all as specified and directed. Note: It shall be measured overall as fixed along the centre line over fittings and accessories.

Demolition of brick work or stone/boulder/block masonry built in cement mortar of any description including all quins, arches, pillars etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Taking down wall panelling and similar work of any description including cover fillets and frame work complete all as specified and directed.

Taking down carefully existing copper/aluminium point wiring (light/fan/bell/sockets) and flame proof point wiring complete with all accessories such as switches sockets ceiling rose, wall bracket etc and removing dismantled material and making good disturbed surface of walls/floors etc matching with existing surface etc complete all as specified and directed.

Taking down of Sub main wiring with two single core cable PVC insulated unsheathed of copper multi strandard conductor cable of any size complete all as specified and directed.

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 200mm, 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match and over including 10 mm thick rendering in cement plaster (1:4) complete all as specified and directed.

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and over including 15 mm thick screed bed or bedding layer in cement plaster (1:6) complete all as specified and directed.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for 10 mm thick Vetrified Ceramic tiles (square/rectangular) polished area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement slurry and pointed in white cement or coloured cement to match the shade of tiles, over and including 15 mm thick screed of beding layer in cement plaster (1:6) complete all as specified and directed.

All as per Srl item No. 26 here in before but on vertical surfaces over 10 mm thick rendering in cement plaster (1:3) finished even and fair, complete all as specified and directed.

M&L for 20-25 mm thick Machine cut kota stone slab flooring over cement screed 20 mm thick in cement mortar (1:6), laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 20-25 mm thick machine cut kota stone slab in riser of steps, skirting, dedo, pillar and verticle surfaces laid over including 15 mm thick in cement plaster (1:4), laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 25 mm thick cement concrete flooring (1:2:4) type B-0 using 12.5 mm graded stone aggregate finished even and smooth without using extra cement complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 using 40mm graded aggregate as in sub base finishing even and fair complete all as specified and directed.

S&F APP based polymeric membrane (Green colour) not less than 3 mm thick ,weighing notless than 3.5 kg/sqm ,reinforced with polyster non woven fabric(weighing notless than 150 gm/sqm ) and upper side of membrane thermally insulated with white mineral gravel finish ,informly embedded during manufacturing process shall only be used .it shall be used by torch application, side overlap shall be75 mm and the ends shall be 100 mm and all over laps shall be sealed by torch application including applying a coat of cold applied bitumen primer confirming IS :3384 @0.4 kg/Sqm complete all as specified and directed.

M&L for cement concrete (1:3:6), type C-2 using, 40mm graded stone aggregate, as in filling and mass concrete etc complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour pvc sheet reinforced with mild steel squre tube complete all as specified and directed.

S&F 30 mm thick (style) factory made solid panel PVC door shutter consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement all as specified and shown on serial pages No. 178 of SSR 2010 (Part-II) and Particular specifications complete all as specified and directed Note: Contractor shall give 6 years guarantee for PVC shutters.

S&F 100 mm Butt hinges stainless steel complete all as specified and directecd complete all as specified and directecd.

S&F 105x60 mm pressed steel door frames with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and directed.

All as per Srl item No. 37 here in before but 125 x 60mm size complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints in complete all as specified and directed.

S&F 25 mm thick block board grade 2 quality interior grade decorative face veneers on both face with including 6 mm thick teak wood lipping fixed with glue and nails all around shutter and fixed with screw to frame work as in kitchen cabinet and cupboards shutters complete all as specified and directed.

S&F 100mm size hasp and staple, safety type of aluminiun anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F 30 mm width of flap continuous piano hinges mild steel bright finish or electro galvanised complete all as specified and directed.

S&F 35 mm thick second class hard wood gauged skeleton shutters open rebeted and prepared to receive glass, gauze etc(without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing gauze,glass etc size of members of shutters as specified in SSR part I, Section 8, Clause 8.24 (a); complete all as specified and directed.

S&F 35 mm thick factory made second class hard wood plain framed panelled shutters (two panels) with lock rails and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces . the size of rail and stile as per IS :1003 (Part -I) Klin Seasoned and chemically pressure treated all as specified and directed.

Preparing new or previously untreated wood of wood based surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel on wooden surfaces (ordinary tint) over one coat of pink primer complete all as specified and directed.

Preparing old painted wood or wood based surface of any description , not otherwise described over 10 cm width or girth and apply one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed.

Preparing new or previously untreated steel and iron surface of any description 10 cm width or girth, not otherwise described and apply two coat of synthetic enamel paint (ordinary tint) complete all as specified and directed.

Preparing old or previously treated steel and iron surface of any description 10 cm width or girth, not otherwise described and apply one coat of synthetic enamel paint (ordinary tint) complete all as specified and directed .

S&F 100mm long mild steel butt hinges 'medium weight', cold rolled mild steel complete all as specified and directed.

S&F 150 mm size extruded aluminium handles fabricated type, anodised and polished etc complete all as specified and directed.

S&F 150mm size aluminium anodised barrel tower bolt of extruded section with cast or sheet barrel and rolled or cast bolts etc all as specified and directed.

S&F 300 mm length aluminium alloy anodised sliding door bolt with hasp,staple and fixed clips of sheet,cast or extruded section, bolts and sliding bolts of extruded section or cast aluminium alloy, etc complete all as specified and directed.

S&F in repairs, 300mm mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall lenth of cover plate 150mm etc complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average wirth of aperture 1.40mm and fixed with stainless steel wire staple etc complete all as specified and directed.

S&F aluminum anodized snap Grid of size 605x605 mm frame work , including 6 mm dia hangers (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60 mm long and expansion hold fasteners 12,5 mm dia 40 mm long complete all as specified and directed.

S&F 12 mm thick gypsum board/ tiles for insulation and acoustic purpose of size 60 cm x 60 cm fixed with screws with staples on aluminum snap grid complete all as specified and directed.

S&F anodised aluminium frame for doors, window, ventilators with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawl plug and screw or with fixing clip or with expansion hold plate fasteners . Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and directed.

S&F anodised aluminium epoxy powder coated door shutter of aluminium section weighing 0.55 Kg/m including necessary joining cleat, glazing clip,ruber neoprene packing handle 2 Nos in each door, hing anodised aluminum, snap beading screws etc complete all as specified and directed.

S&F anodised aluminium window and ventilator shutter, fixed type without sashbars,aluminium section weighing 0.55 Kg/m including necessary joining claets,glazing clips,rubber packing,anodised aluminium snap beading screws, handle, hinges, tower bolts as per requirment etc complete all as specified and directed.

S&F 5.5 mm thick sheet glass ordinary quality in square not exceeding 0.5 sqm in each pane complete all as specified and directed .

S&F 6 mm thick bakelite sheet coloured, preliminated both sides with colour choice laminations for fixing in doors partitions etc., confirming to relevant IS complete all as specified and directed.

S & F framed work such as grills, grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290 (Gde–E–165) complete all as specified and directed.

M&L for cement concrete (1:3:6) type C–0 using 12.5 mm graded stone aggregate, as in filling of pressed steel frame and hold fast blocks etc complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed.

S&F in repairs, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperature 1.40mm to steel frame of window with tinned tacks or galvanised wire stapels complete all as specified and directed.

S&F 150 mm size Aluminium anodised barrel tower bolts of extruded section complete all as specified and directed

S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast – aluminium alloy and fixed complete all as specified and directed.

S&F 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast – aluminium alloy and fixed complete all as specified and directed.

S&F 150mm size extruded aluminium alloy handles fabricated type complete all as specified and directed.

M&L for 15 mm thick rendering cement plaster in cement martar (1:4) to wall surfaces on fair faces of brickwork or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement martar (1:6) to wall surfaces other than fair faces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5mm thick, rendering in cement plaster in cement martar (1:3) to ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed.

Preparing new plaster surfaces on celling and apply three coats of white wash complete all as specified and directed .

Preparing old decorated plastered surfaces of ceilling and apply one coat of white lime wash complete all as specified and directed.

Preparing new plastered surfaces on walls and apply two coats of oil bound distemper of approved shade/tint over a coat of primer complete all as specified & directed.

Complete removal of existing treatment of walls and apply two coats of oil bound distemper over chalk whiting including filling spots with wall care putty complete all as specified and directed.

Preparing old decorated plastered or unplastered surfaces of walls and apply one coat of lime white wash complete all as specified and directed.

Preparing new plastered surfaces of walls and apply two coats of white wash complete all as specified and directed.

Preparing new plastered surfaces of walls and apply two coats of cement base paint of approved shade over chalk whiting complete all as specified and directed.

Preparing old plastered surfaces of walls and apply one coat of cement base paint complete all as specified and directed.

S&F steel ventilators with top hung shutter including hinges ,steel peg stay ,complete all as specified and directed.

S&F 20mm bore steel water tubing galvanised, “medium grade” with all fittings fixed to wall and ceiling or in floor complete all as specified and directed.

All as per Srl item No.83 here in before but refixing with new fittings complete all as specified and directed.

S&F 15mm bore steel water tubing galvanised , “medium grade” with all fittings and fixed to walls and ceiling or in floor complete all as specified and directed.

All as per Srl item No.85 here in before but refixing with new fittings complete all as specified and directed.

S&F in repairs, 15mm bore bib taps , cast copper alloy chromium plated, fancy type with crutch or butterfly handle, screwed down screwed for iron pipe complete all as specified and directed.

S&F in repairs, 15mm bore, bib taps, cast copper alloy, with crutch or butterfly handles, screwed down, screwed for iron pipe or brass ferrule for complete all as specified and directed.

S&F in repairs, 15mm bore, Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe etc complete all as specified and directed.

S&F in repairs, 20mm bore, Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe etc complete all as specified and directed.

S&F in repairs, 15 mm bore, fancy type chromium plated concealed type, stop valves, cast copper alloy with long shank and cup with crutch or butterfly handles screwed down high pressure, screwed both ends for iron complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 500 ltrs capacity double layer ISI marked (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 1000 ltrs capacity double layer ISI marked (Cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

S&F 20mm bore ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repairs, 15mm bore, Brass CP basin mixer for mixing hot and cold water screwed down for iron pipe and fied complete all as specified and directed.

M&L for reinforced cement concrete (1:2:4), nominal mix, type B-1, using 20 mm graded stone aggregate for chajjas and similar items complete all as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slab and similar work not exceeding 200mm thick with rough finished surface of concrete complete all as specified and directed.

S&F mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed.

All as per Serial Item No. 98 here in before but in stirrups, spacers and binder etc complete all as specified and directed.

S&F of 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with lead joints, laid in trenches or in floors complete all as specified and directed.

S&F 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with lead joints, laid in trenches or in floors complete all as specified and directed.

S&F 100mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed.

S&F 75mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed.

S&F for 75 mm dia of outlet cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed.

S&F for 100 mm dia for outlet cast iron floor trap 100 mm with grating including jointing to waste pipe fixed in cement concrete (1:2:4), type B-1 all as specified and directed.

S&F in repair 100mm dia Grating doom PTMT(minimum weight 25gms) complete all as specified and directed.

S&F bands straps supports or stays for rainwater ventilating pipes including bolts confirming to Fe 290Gde-E-165 all as specified and directed.

Cutting holes into brick wall for inserting hold fast etc built in cement martar not exceeding half brick wall and making good in cement concrete (1:2:4), type B-I, complete all as specified and directed. Note: Depth of embedded portion of hold fast and lugs shall be measured from the face of the jamb into the wall.

S&F 110mm bore PVC (SWR) rain water pipe single socketed in any length with rubber ring joints, jointed with solvent joint fixed to wall complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

M&L for precast cement concrete type (1:5:10), type E-1, using 20 mm graded crushed stone aggregate in block masonry with solid blocks exc. 10 cm in width and setting in cement mortar (1:6) complete all as specified and directed.

S&F in repair, brass chromium plated tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and directed.

S&F in repair, PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F water closet vitreous china squatting pan "Orissa pattern" size 580mmx440mm white with integral foot rests (Excl flushing cistern and flush pipe) complete all as specified including CI 'P' trap all as specified and directed.

S&F in repairs, vitreous china urinal, bowl type (back or corner wall type) complete including providing and fixing plugs badding uinal against wall in cement concrete (1:2) ,securing urinal to plugs with and including 60 mm long bass scews ,pointing around urinal back in cement ,fixing automatic flushing cistern in brackets,flush pipe,grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern ,trap and waste pipe) complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (Pedstal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including plastic water closet seat cover, black cosed pattern with flat bottom, and cover and mild steel chromimum plated hinging device complete all as specified and directed.

S&F in repairs, 10 litres capacity low level PVC valveless syphonic action type flushing cistern with inlet ball valve, float and handle including brackets with 32mm dia flush pipe of polyethylene of low or high density complete all as specified and directed

S&F in repair 25 mm dia stainless steel curtain rod (minimum weight 0.36 Kg per RM) with brackets, fancy knobs and rings (20 cm c/c) etc complete all as specified and directed.

M & L for 50 mm thick cement concrete (1:3:6), type C–1, using 20mm graded stone aggregate as in plinth protection finished even and smooth etc complete all as specified and directed.

S&F second class hard wood small fittings such as brackets of any type shaped door and window stops and the like including all necessary labour article n.exc 200cucm each all as specified and directed.

Supply only internal Water proofing compound complete all as specified and directed.

M&L for cement concrete (1:5:10), type E-2, using 40mm graded aggregate as in filling and mass concrete etc complete all as specified and directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etccomplete all as specified & directed.

Taking down carefully steel rolling shutters including hood of size exceeding 25 Sqm for replacement of unserviceable & defective parts and refixing in the same opening after cleaning of guide rails, lath top cover by kerosene and proper greasing, oiling, replacement of rusted nuts bolts etc. removing of bent, disturbed surface, making alignment etc. to make good the system and size, bearing of adequate size/in hinges for rolling shutters and bevel gear complete all as specified and directed.

S&F ball bearing for rolling shutters suitable for any size of rolling shutters complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

S&F bevel gear box and crank handle of suitable size to existing old rolling shutters including making opening to wall and making good disturbed surface after fixing of gear box complete all as specified and directed.

S&F steel rolling shutter made out of 1.25 mm thick laths, without ball bearing ,as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer ,erecteted in position as indicated ,complete:gear operated type with bevel gear box and crank handle complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc.,conforming Fe-290 (Gde E-165 complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular or polygonal on rough finished surfaces of concrete complete all as specified and directed.

M&L for form work to sides and soffits of floor or roof beams ,beam haunchings ,girders,bressumers,lintels,cantilevers,shelves including supports,overhangs etc also splays between floor and beams complete all as specified and directed.

M&L for RCC M-25 design mix (using 20 mm graded stone aggregate) as in beams ,cantilevers ,bressumers,lintels over 1.5 m span all as specified and directed. Note: Design mix shall be got carried out by the contractor from NIT/IIT/Govt Engg College/Govt approved labs and approved by GE before concrete work. Nothing extra shall be admissible to contractor this work.

M&L for RCC M-25 design mix (using 20 mm graded stone aggregate) as in columns, piers piers posts and struts all as specified and directed. Note: Design mix shall be got carried out by the contractor from NIT/IIT/Govt Engg College/Govt approved labs and approved by GE before concrete work. Nothing extra shall be admissible to contractor this work.

S&F mild steel frame work for fixing PUF panels including drilling holes in frame works complete all as specified and directed.

S&F in repair dash through bolts of dia 6 to 8 mm and length not less than 80 mm including drilling holes using electric drill machine in concrete /masonry work complete all as specified and directed.

S&F in repair 40 mm thick PPGS (Pre painted Galvalume steel)PUF ecofriendly panel board comprising of 0.5 mm thick pre painted MS sheet face panels sandwitched with PUF (polyurathane foam) injected to achieve foam density not less than 40 Kg/cum complete all as specified and directed. Note: No deduction shall be made for openings made for accomodating windows ventilators

S&F solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixed at site on PVC frame as per specification and drawing complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC Frame inclusive PVC fillets & PVC strips as per specification and drawing complete all as specified and directed.

Dismantiling old existing unserviceable cement plaster, loose/unsound weaken cement concrete of any description and in any position from existing external/ internal surfaces of RCC/ slab beam/ columns RCC facias/ masonary wall etc average depth 25mm (approx height upto 15 m from natural ground level) with power driven pnnumatic chisel and removal of rabbish upto the approved municipal dumping ground outside MOD land including cutting of all making square shoukders of the cavities roughening the smooth surfaces scrapping out/removing corrosion all loose/scale/urst etc from the visible reinforcement properly and then applying single component cementious corrosion inhibiting primer fro steel reinforcement on visible reinforcement surfaces to form a continuous film not less then 1mm thick and preparing the surface to receive concrete of epoxy grount mortar and including providing necessary props bracing and runners of relieve the members from as required and as per design and pattern including preparing the surfaces to match with the existing surface complete all as specified and directed.

M&L for providing and filling epoxy putty into RCC crack after opening up RCC cracks in V-groove manner approximate 5X5 mm size using mechanical cutter properly cleaning the same to remove loose dust,dirt etc and filling the same using Nitcote VF.Three component slovent free thixotropic Epoxy resin based putty having 100% solid contents mixed density of 1.6 g/cc compressive strength 50 N/sqmm pot life of 40 minutes at 24C Drying time 8 hrs recoatable time 24 hrs and finishing in line and level with existing concrete surface etc comolets all as specified and derected.

M&L for providing and applying corrosion resistant non shrink free flow cementitious one component micro concrete with average thickness 50mm using having compressive strength (BS 4551-80-60) MPA at 28 days tensile strength (ASTM C 348)-2.0 N/MM2 @ 28 days Flexural strength (ASTM C 348)-9 EPOXY BONDING AGENT TM Bond FP Thermax having mix density of 1.45 to 1.5 kg/ltr compressive strength (BS-6319 PT 3) -25 Mpa at 7 days , having an over lay time of 3 hrs at 30c pouring of micro concrete into thye formwork using suitable arrangementy or if required using pumping device for and the bottom shutering after 7 days ensuring proper bond between the micro concrete and existing concrete substrata etc including all tools and tackles as per acceptingofficver complete all as specified and directed.

M&L for providing and applying rendering 15mm thick first layer of thermax BS 5F (single component Thixotropic fibre reinforced polymer modified repair mortar to achieve compresove strength to apply epoxy bonding agent TM bond ED thermax haing mix density of 1.45 to 1.5 Kg/Ltr, compressive strength (BS 6319 pt 2)-40 MPa at 7 days flexural strength (BS 6319 PT 3)-25 MPa at 7 days, bond strength (ASTM C 881) 11 N/mm2 at 7 days, having an over lay time 3 hrs at 30C complete all as specified and directed by Engr-in-Charge.

M&L for point wiring for one light point /fan point/bell point controlled by one switch with 1.5 Sqmm (nominal area) PVC insulated, unsheathed multi strand copper conductor cable FR-LS (Phase and Neutral) in existing concealed PVC conduit and fitting including new steel terminal sunken boxes suitable for modular switch/socket flush to surface (including modular frame and cover plate) for one light point, fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 Sqmm multi stranded copper conductor cable FR-LS (Earth) connected to common earth dolly complete all as specified and directed.

All as per Serial Item No 144.00 here-in-before but for one socket point outlet 3 Pin, 5 Amp 230 Volt on independent board complete all as specified and directed.

All as per Serial Item No. 144.00 here-in-before but for 3 pin 15 Amp socket out let by using 2.5 Sqmm PVC insulated unsheathed copper conductor cable FR-LS multi strand (phase & Neutral) on independent board including provn of 2.5 Sqmm unsheathed, multi stranded copper conductor cable FR-LSH continues as earth wire connected to earth dolly etc complete all as specified and directed.

M&L for point wiring for one light / fan/bell point controlled by one switch with 1.5 Sqmm (nominal area) PVC insulated, unsheathed multi strand copper conductor cable FR-LS (Phase & Neutral) in concealed PVC conduit 20 mm dia heavy duty ISI marked, steel terminal sunken boxes and 3 mm thick phenolic laminated sheet top cover for sunken boxes flush to surface for one light point/fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 Sqmm copper conductor cable FR-LSH connected to common earth dolly complete all as specified and directed. (Note :- Chases cutting & making good ,Switches, sockets etc shall be measured and paid for separately under appropriate items of Sch of work)

All as per Serial Item No 147.00 here-in-before but for socket 5 Pin, 5 Amp 230 Volt on same board complete all as specified and directed.

All as per Serial Item No 147.00 here-in-before but for one socket point outlet 3 Pin, 5 Amp 230 Volt on independent board complete all as specified and directed.

All as per Serial Item No 147.00 here-in-before but for 15 Amp socket out let by using 2.5 Sqmm PVC insulated unsheathed copper conductor cable FR-LS multi strand on independent board complete all as specified and directed.

Cutting chases, pinning in brick walls. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F switch piano flush type, 5 Amp 240 Volt, AC (ISI Marked) one way etc complete all as specified and directed.

S&F bell push flush type, 5 Amp 240 Volt complete all as specified and directed.

S&F one socket flush type outlet 5 Pin 5 Amp, 230 volts AC complete all as specified and directed.

S&F one switch socket combination 2 in 1, 5 Amp, flush type complete all as specified and directed.

S&F Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal 230 volts AC complete all as specified and directed.

S&F in replacement of LED fitting 1 x20 Watt, 220 V, AC decorative box type with driver, holder including LED tube light rod connection with 3 core flexible copper conductor of suitable size from ceiling rose to tube fitting connection etc complete all as specified and directed.

S&F in replacement of LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F stepped type elecronic fan regulator flush type existing phenolic laminated sheet ect as required suitable wattage, 230V suitable for 1200/1400 mm ceiling fan etc complete all as specified and directed.

S&F ceiling rose surface bakelite 65mm x 50mm, 2 to 3 terminals with back plate etc complete all as specified and directed..

S&F in replacement of LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.with GI bracket made out of suitable size of light grade pipe 32 mm dia tubing upto 1.2 mtr length bent to shape with 02 sets of MS clamps made out of 25x3 mm MS flat iron with suitable bolt and nuts and testing etc complete all as specified

S&F call bell ding dong type, AC, 230 V etc complete all as specified and directed.

S&F Sub main wiring with two single core cable PVC insulated unsheathed of copper multi strandard conductor cable of size 4 sqmm, 1100 volts grade drawn through concealed PVC conduit not less than 20 mm medium duty and including PVC insulated 2.5 sqmm unsheathed multistranded FR-LSH copper conductor cable for earth continuity and connected to common earth dolly complete all as specified and directed

S&F Sub main wiring with two single core cable PVC insulated unsheathed of copper multi strandard conductor cable of size 6 sqmm, 1100 volts grade drawn (2x4.0 Sqmt + 1x4 Sqm earth wire) through concealed PVC conduit not less than 20 mm medium duty and including PVC insulated 4 sqmm unsheathed multistranded FR-LSH copper conductor cable for earth continuity and connected to common earth dolly complete all as specified and directed

S&F in replacement of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 240 volt 20Amps complete all as specified and directed

S&F in repairs, double door sheet metal enclosure made out of CRCA mild steel sheet concealed surface mounting TPN, 4 way, 415Volt, suitable for fixing MCBs, isolators etc including taking down old complete all as specified and directed.

S&F in repairs, double door sheet metal enclosure made out of CRCA mild steel sheet concealed surface mounting SPN, 8 way,240Volt, suitable for fixing MCBs, isolators etc including taking down old complete all as specified and directed.

S&F in repairs, double door sheet metal enclosure made out of CRCA mild steel sheet concealed surface mounting SPN, 12 way,240Volt, suitable for fixing MCBs, isolators etccomplete all as specified and directed.

S&F in replacement of MCB TPN 125 Amps 'C' curves repturing capacity 10 KA etc complete all as specified and directed

S&F in replacement of MCB TPN 63 Amps 'C' curves repturing capacity 10 KA etc complete all as specified and directed

S&F in replacement of MCB SPN 63 Amp 'C' curves repturing capacity 10 KA etc complete all as specified and directed

S&F in replacement of MCB SPN 40 Amp 'C' curves repturing capacity 10 KA etc complete all as specified and directed

S&F in replacement of MCB SP 6 Amp to 32 Amp 'C' curves repturing capacity 10KA rupturing capacaity complete all as specified and directed.

Taking down serviceable/unserviceable ceiling fans 1200mm/1400 mm sweep 230 V, AC, single phase from ceiling, dismantling the ceiling fan and taking out complete rewinding the same with super enameled copper winding wire of existing gauge & size including throughly cleaning all the components of fan, oiling varnishing the fan with and including replacement of rusted/unserviceable nuts, bolts, split pin, rubber reel, flexible twin core copper cable of size 23/.00076 approximate one metre long for each fan, machine screws and painting the fans etc, and refixing the repaired fan to existing place complete all as specified and as directed.

Taking down serviceable/unserviceable exhaust fan /flame proof exhaust fan of any sweep 230 V, AC, single phase , dismantling the Exhaust fan and taking out complete rewinding the same with super enameled copper winding wire of existing gauge & size including throughly cleaning all the components of fan, oiling varnishing the fan with and including replacement of rusted/unserviceable nuts, bolts, split pin, rubber reel, flexible twin core copper cable of size 23/.00076 approximate one metre long for each fan, machine screws and painting the fans etc, and refixing the repaired fan to respective bathrooms complete all as specified and as directed.

M&L for earthing with galvanized steel plate electrode 600 x 600 mm x 6 mm size directly burred in ground vertically earth pit not less than 2.25 deep below normal ground level with top edge of the earth plate not less than 1.5 m below normal ground level surrounded with coal dust and common salt filling in alternative layers of 15 cm thick each connected to and including GI earth wire 4 mm dia by means of GI nuts, bolts, check nuts & washers etc connecting to earthing test point, main switch board and including 15 mm dia GI pipe light grade for protection of earth lead from earth plate upto 5 mtr and 20 mm dia GI pipe medium grade connected with funnel having wire mess for watering purpose including necessary excavation and earth work, PCC (1:2:4) type B-1 (using stone aggregates) for earthing pit, 10mm thick cast iron cover with angle iron frame all as specified and shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and as directed.

M&L for flameproof point wiring for one light/fan point controlled by one switch with 1.5 Sqmm (nominal area) PVC insulated, unsheathed multi strand copper conductor cable FR-LS drawn in and including concealed stove enamelled steel conduit of 20 mm dia heavy duty including accessories such as Tee, bend, Elbow etc, ISI marked, fire proof steel terminal sunken boxes flush to surface for one light/fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 Sqmm copper conductor cable FR-LS connected to common earth dolly complete.

All as per Serial Item No. 177.00 here-in-before but for 15 Amp socket out let by using 2.5 Sqmm PVC insulated unsheathed copper conductor cable FR-LS multi strand on independent board including provn of 2.5 Sqmm unsheathed, multi stranded copper conductor cable FR-LS continues as earth wire connected to earth dolly etc complete all as specified and directed.

S&F in replacement of switch flame proof rotary type with termination box in LM 6,16Amp, single pole ON-OFF ,250 Volt complete all as specified and as directed.

S&F in replacement of flame proof switch socket & plug combine in LM6 cable termination box in LM6,16A, 250V, 2P+earth complete all as specified and as directed.

S&F in replacement of LED light fitting 2 x 16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed.

S&F in repairs, submain for flameproof Sub main wiring with two single core cable PVC insulated unsheathed of copper multi strandard conductor FR-LSH cable of size 2.5 sqmm, 1100 votls grade drawing through and including concealed flame proof steel conduit 20 mm dia heavy duty including accessories such as tee, bend, elbow etc, ISI marked with and including PVC insulated 1.5 sqmm unsheathed multistranded FR-LSH copper conductor cable for earth continuity and connected to common earth dolly complete all as specified and as directed.

S&F in repairs, flame proof sheet metal enclosure made out of CRCA mild steel sheet concealed surface mounting SPN, 2 way, 415 Volt IP protection 65, including MCB DP 16/25 Amp -1 No and MCB SP 6Amp/10Amp - 2 Nos complete all as specified and as directed.

M/S SOLANKI GENERAL SUPPLIERS

Beenu Co. Company

KRISHNA CONSTRUCTION COMPANY

M/S VISHNOI ENTERPRISES