SPECIAL REPAIRS TO QUARTER NO 35/122 TO 35/125 IN CENTRAL ZONE UNDER GE (NORTH) BINNAGURI

Amount

Taking down PVC soil pipe of any dia with fittings from wall/ trenches of any description including fittings complete all as specified and as directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches or in floors complete all as specified and as directed.

S&F 110mm dia PVC bends of any radius with access door complete all as specified and as directed.

S&F 110mm dia PVC (SWR) branch piece single (single 'Y'/T) equal or unequal with access door complete all as specified and as directed.

S&F 110mm dia PVC SWR vent cowl complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches or in floors complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

Dismantling water tank exc 500 & n.exc 1000 ltr capacity and removing to store complete all as specified and as directed.

Supplying & fixing of PVC water storage tank 1000 ltr capacity HDPE double layered , cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection including locking arrangement, including supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 20 mm - 210 gms) complete all as specified and as directed. Note : GI inlet, outlet & wash out pipe will be measured and paid separately.

Supplying & fixing of PVC water storage tank 500 ltr capacity HDPE double layered, cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection including locking arrangement, including supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 20 mm - 210 gms) complete all as specified and as directed. Note : GI inlet, outlet & wash out pipe will be measured and paid separately.

S & F 20mm dia gun metal globe or gate valve conforming to IS:778 with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified and as directed.

Taking down tarfelt with cement plaster from roof surfaces and lowering and removing the same to a distance exc. 50m and n. exc. 100m including roughening of old concrete surface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified and as directed .

M&L for 10mm thick screed bed or bedding layer in cement mortar (1:4) mixed with liquid water proofing compound @200ml per bag of cement or as per manufacturer's instruction in order to maintain proper slope over existing roof surfaces for applying roof treatment, finished even and smooth without using extra cement complete all as specified and as directed. Note : Liquid WPC will be measured and paid separately.

M&L for providing and applying single component acrylic polymer modified, fibre reinforced waterproof coating in 4 coats of application:- (a) Applying primer coat with Primer @ 0.3 kg /sqm as per manufacturer instruction. (b) Over priming coat applying water proofing coat as per manufacturer instructions with fibre reinforcement @ 0.75kg/sqm on the flat or vertical surfaces over parapet wall and ensure that there are no bubbles of creases. Overlapping of the fibre is a minimum of 50mm and allow this coat to dry for a period of 2-6 hrs depending on the atmospheric condition. (c) Applying second coat of water proofing coat @0.75Kg/sqm. (d) Applying final coat of primer @ 0.08kg/sqm after 2nd coat has dried properly. Note : Water Proofing treatment shall be carried out by authorised applicator approved by the manufacturer.

Roughening surfaces of old concrete floor by picking, sweeping, cleaning and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

M&L for Vitrified Ceramic tiles light shade 8 to 9 mm thick (square/ rectangular) polished, area of each tiles exc 0.72 sqm not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles as in floor and including 15mm thick screed bed or bedding layer in CM 1:6 etc complete all as specified and as directed.

M&L for Vitrified Ceramic joint free tiles 8-9 mm thick (square/ rectangular) polished, area of each tiles exc 0.72 Sqm but not exceeding 1.00 sqm, in skirting/daddo over 10 mm thick rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises including taking down cement plaster complete all as specified and as directed.

M&L for coloured non skid ceramic tiles (1st quality) 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc set and jointed in neat cement slurry over 15mm thick screed bed or bedding layer in CM (1:6) as in floor and pointed in white or coloured cement to match complete all as specified and as directed.

M & L for glazed ceramic coloured/digital printed/ Elevation tiles 300X450X 7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. confirming IS : 13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile approved laid over 10mm thick rendering in CM (1:4) as in vertical surfaces of skirting, dados, steps complete all as specified and directed.

M & L for glazed ceramic coloured/digital printed/Elevation tiles 300 x 600 x 8 mm thick as on vertical surface of wall such as skirting, dado, riser etc. confirming to relevant IS grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile approved laid over 10mm thick rendering in CM (1:4) as in vertical surfaces of skirting dados repairs to steps complete all as specified and as directed.

M&L for providing and laying of 300 x 300 mm/200 x 200 mm & 10mm thick anti-skid pavement tile Endura tile of "H & R Johnson India" or equivalent in Pavit or NITCO or techno commercially equivalent make as listed in List of Makes in approved color & Shade and in anti skid finish set and jointed in neat cement slurry and pointed in white cement & pigment to match over and including 20 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed. Note: Design/pattern shall be as approved by GE at the time of execution.

Demolition of stone slab and tiles of any description or thickness as in floors, apron etc laid dry or bedded and pointed in any mortar complete all as specified and as directed.

M&L for 15 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, Jambs, pillars, window cills, cooking platforms, corner shelf, flat shelf and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15 mm thick cement plaster (1:4) including rounding the exposed surfaces of granite complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store of 15 mm bore complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store of 20 mm bore complete all as specified and as directed..

S&F of Tubes, medium grade, 15mm bore, galvanised, with all fittings and fixed complete to wall and ceilings or laid in floors complete all as specified and as directed.

Refixing of old steel tubing and connections in new or old position (wall, ceiling, floors, etc) of 15 mm bore complete all as specified and as directed. Note : The serviceable GI tube obtained from taking down shall be reused.

S&F of Tubes, medium grade, 20 mm bore, galvanised, with all fittings and fixed complete to wall and ceilings or laid in floors complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc complete all as specified and as directed. Note : The serviceable GI tube obtained from taking down shall be reused.

Taking down cement plaster on brick work of any description including racking out joints and cleaning dust etc including removing rubbish material complete all as specified and as directed.

M&L for applying average 15mm thick plaster in two coats (10mm+5mm) with ready mix pre-packed proportioned dry mix mortar, blended with PP fibres, mixed with liquid water proofing compound on top layer on fair faces of brick wall or concrete surfaces additives on external surfaces finished the surface even and fair without using extra cement including transporting of material, mixing, curing, scaffolding etc complete all as specified and as directed. Note : Liquid water proofing compound will be measured and paid separately as supply only.

M&L for rendering 15mm thick in CM 1:6 on brick or concrete surface finished fair and even without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even and fair without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound conforming to relevant IS complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls by applying one coat of putty and sand papering surfaces to achieve smooth surfaces and applying two coats of acrylic based distemperof approved tint over a coat of alkaline resistant primer with roller including washing floors, cleaning glass, joinery, electrical fittings, wiring etc of drops and splashes complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered and painted surfaces and distempering walls by applying one coat of acrylic based distemper of any tint/shade with roller including wall putty / white cement wherever required to fill the wall cracks/holes complete all as specified and as directed.

M&L for preparation of new plastered surfaces on wall / ceiling / chajjas and applying two or more coats of 10-0% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior weather proof paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 Ltre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surfaces as per the manufacturer instruction and all coats including primer to be applied with fully automatic airless spray machine of paint application with flow speed of minimum 1 Ltr per minute having pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and as directed.

M&L for complete removal of existing treatment of old decorated treatment on wall / ceiling / chajjas by scrapping with true care wall sander : L-01/H-01 (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 grit having dia 7"/9" to make the surface free from dust, loose paints etc or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling cracks, holes etc complete and applying Two or more coats of 10-0% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 Ltre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over treated surfaces as per the manufacturer instruction and all coats including primer to be applied with fully automatic airless spray machine of paint application with flow speed of minimum 1 Ltr per minute having pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and as directed.

Material and labour of preparation of new plastered or unplastered surfaces of ceilings and applying three coats of white wash including washing floors, cleaning glass, joinery, electrical fittings, wiring etc. of drops and splashes complete all as specified and as directed.

M&L for preparing old decorated plastered or unplastered surfaces of ceiling including cornices, pilasters and other wall features etc by brooming down or steel wire brushing scrapping down to remove smoke soot moulds moss and efflorescence salts and treating oil and greasy spots etc and applying two coats of white washing on the same complete all as specified and as directed.

M&L for preparing old decorated plastered or unplastered surfaces of walls including cornices, pilasters and other wall features etc by brooming down or steel wire brushing scrapping down to remove smoke soot moulds moss and efflorescence salts and treating oil and greasy spots etc and applying two coats of white washing on the same complete all as specified and as directed.

Demolition of brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles including removing of demolished material from work site complete all as specified and as directed.

Material and labour for brickwork with fly ash bricks, old size, having compressive strength not less than 75Kg sqcm, straight or curved on plan exc 6 M mean radius in built in cement and sand mortar 1:6 complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for including removing of demolished material from site to distance exc 100 mtr but n.exc 150 mtr complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specially provided for as in floors, surface channel etc complete all as specified and as directed.

M&L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) in water tank platforms, flooring etc complete all as specified and as directed.

Material and labour for 75mm thick PCC (1:3:6), type C-2 (using 40 mm graded crushed stone aggregate ) as in plinth protection; pathway / hard standing etc laid in bays / panels not exc. 2.00 Sqm each including construction joints at suitable interval and each corner and filled with bituminous mastic filling (1 part bitumen & 3 part sand) and finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 as in sub base using 40mm graded mechanically crushed stone aggregate complete all as specified and as directed.

Material and labour for 80 mm thick coloured rubber moulded machine pressed precast concrete interlocking paver block chemically treated any shape, size and colour conforming to IS 15658-2006 of M-40 Grade with grey cement and pigment over and including 40 mm thick sand cushion spread and laid leveled in layers complete all as specified and as directed.

Taking down chowkat with shutter exc 1.5 sqm and n. exc. 4.00sqm each including Builder's Hardware complete all as specified and as directed.

Taking down chowkat with shutter n.exc 1.5sqm each (without taking off shutter from the frame) including Builder's Hardware complete all as specified and as directed.

M&L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filling hollow space of steel chowkats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and as directed.

M&L for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/chowkhat of size 50 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note : For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and as directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L for factory made single extruded WPC (Wood Polymer Composite) solid coloured decorative flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and as directed. Notes: (a) Stainless steel butt hinges and necessary fittings shall be paid separately. (b) Design and pattern shall be approved by the Engr-in-Charge/GE at the time of execution of work.

M&L of factory made partly glazed i.e upper colour panel will be wire mesh fitted externally in the clear space & lower panel will be colour PVC sheet 5mm thick PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom, rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for sides and plain colour PVC sheets for botop rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet PVC sheet beading, and jointed together with solvent cement complete all as specified and as directed. Notes: (a) Stainless steel butt hinges and necessary fittings shall be paid separately. (b) Design and pattern shall be approved by the Engr-in-Charge/GE at the time of execution of work.

M&L for providing and fixing factory made single UPVC white colour sliding window three track made of extruded profiles with wall thickness of 2.3mm ( + 0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x52mm), sliding mesh sash (42x75mm ). sliding interlock ( one vertical length in each shutters) (45.5mmx28mm), glazing bead (24.5mmx16mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware . EPDM gasket , 1.2+ 0.2mm thick galvanised steel frame (30mmx 18mm) 2 Nos , sliding sash (30x18mm), sliding mesh sash (26x10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x100mm long fasteners, (Hardware; Touch lock of zinc alloyed (white powder coated), steel roller system Stainless steel wire cloth 0.36mm normal dia of wire and average width of aperture 1.40mm and required accessories) complete all as specified and as directed.

S&F powder coated aluminium louvered ventilators of size 600X600mm with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading, screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing steel ventilator and making good disturbed surface of wall complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification with Wood free EPS as per specification and drawing complete all as specified and as directed.

M & L for providing & fixing factory made solid PVC cup board frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5 mm thick PVC sheet of density 600Kg/cbm having pattam width of 50mm and thickness of 10mm. All three frame length reinforced with 19mm x 19mm MS square tube of 19 gauge. Mitre cut at two corners and joined with two nos of 150mm long brackets of 15X15mm MS square tube or joint by fusion hit welding. The door frame shall be fixed to the wall thickness using 8Xthroughout the frame and metre cut at two corners and jointed with 2 Nos of 150mm long brackets of 15mm x 15mm MS square tubes. The door frame shall be fixed to the wall using 8/100mm long MS screws through the frame by using PVC fasteners. A minimum 4 nos of screws to be provided for each vertical member and minimum 2 Nos of screws to be provided to the horizontal member etc complete all as specified and as directed.

M & L for providing & fixing factory made solid PVC cup board shutter (Flush type) of 24 mm thick made from co-extruded 3 layer rigid PVC foam sheet (single extruded) with density not less than 600kg/cbm outer layer (0.8-1mm) thick should be of rigid PVC with density of not less than 1400kg/cbm manufactured byan ISO 9001-2015 certified company. Door should be water proof, termite proof, fire retardant and having good screw holding capacity complete all as specified and as directed.

M&L for providing and fixing factory made PVC shelf/partitation of required size consisting of 40mm thick solid PVC sandwich with 1mm thick plain PVC sheet on both sides suitably fixed in MS angle frame complete all as specified and as directed.

M & L for 75mm Hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S & F 75mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 100 mm size butt hinges stainless steel complete all as specified and as directed.

S&F for stainless steel of 150mm long decorative type handle complete all as specified and as directed.

S&F for stainless steel of 200mm long barrel tower bolt complete all as specified and as directed.

S&F for stainless steel, sliding door bolt of 300mm long bolt plate type decorative with bright bolt not less than 12mm dia with and including min of 6 bolts and nuts, four on bolt plate and two on staple fixing complete all as specified and as directed.

S&F door stopper 14cm long of alluminium alloy and tongue, anodised with hard drawn steel spring, foxed in floor etc complete all as specified and as directed.

S&F of stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned stacks, or galvanised wire staples etc complete all as specified and as directed.

S&F of mild steel work such as window guard bars, ladders and similar work conforming to Fe – 290 Grade – E 165 complete all as specified and as directed.

S&F of medium weight, cold rolled mild steel, SS finish, (Partial overlay/fully overlay of any type) diameter of cup 35mm, hinge cup depth 11.5mm, soft-closing hinge complete all as specified and as directed. Make : Godrej kitchen fitting or techno commercially equivalent make as approved by the GE.

M&L for stainless steel of 304 grade electro -polished for corrosion resistance modular thali holder / basket having size of 42x58.5 x20cm including telescopic drawer having weighting capacity of 6 kg complete all as specified and as directed. Make : Cat Part No 5704 Godrej kitchen fittings or techno commercially equivalent make as approved by the GE.

M&L for stainless steel of 304 grade electro -polished for corrosion resistance modular cup & saucer holder / basket having size of 52x53.5 x10cm with telescopic drawer chaenal having weighting capacity of 4 kg complete all as specified and as directed. Make: Cat Part No 5837 Godrej kitchen fittings or techno commercially equivalent make as approved by the GE.

S&F SS of 304 grade 200mm length stainless steel cabinet drawers handles complete all as specified and as directed. Make : Godrej kitchen fittings or techno commercially equivalent make as approved by the GE.

S&F of stainless steel grain trolley SS 304 grade having size 525x485x350mm, with heavy duty and steel with finish of zinc , corrosion resistance with telescopic drawer channel having weight capacity of 25 kg complete all as specified and as directed. Make: Cat Part No 6175 Godrej kitchen fittings or techno commercially equivalent make as approved by the GE.

S&F of stainless steel plane wire basket / trolley SS 304 grade having size 506x480x200mm, with heavy duty and steel with finish of zinc , corrosion resistance with telescopic drawer channel having weight capacity of 25 kg complete all as specified and as directed. Make: Cat Part No 4265 Godrej kitchen fittings or techno commercially equivalent make as approved by the GE.

S&F of stainless steel modular perfored cutlery basket / trolley SS 304 grade having size 520x485x100mm, with heavy duty telescopic drawer channel having weight capacity of 6 kg complete all as specified and as directed. Make: Godrej kitchen fittings or techno commercially equivalent make as approved by the GE.

S&F of stainless steel 304 grade size 180x515x485 mm, pull out detergent rack having two shelf spacers with telescopic drawer channel having weight capacity of 6 kg complete all as specified and as directed. Make: Godrej kitchen fittings or techno commercially equivalent make as approved by the GE.

Taking down rolling shutter of any description exc 2 sqm but n exc 5 sqm each and removing to store from site complete all as specified and as directed.

M&L for Rolled Mild Steel framed work as in doors or gates of angle or other section Fe-410-W(Gde-E-250)Quality-B with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (including steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for compete all as specified and as directed.

M&L for Rolled Mild Steel framed work in tubular trusses such as in column, roof trusses, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle channel or flat section, tube etc) including distance pieces, cleats etc including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 complete all as specified and as directed.

M&L for preparation of new or previously untreated steel and Iron surface of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old steel and iron surfaces of any description not otherwise described, over 10 Cm width or girth and applying one coat of synthetic enamel paint 1st quality complete all as specified and as directed.

M&L for cutting holes in brick walls built in cement mortar of superficial area nexc 150 sqcm complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F of table top WHB, vitreous china, white flat back of size 550mm x 400 mm x 140 mm including 32mm nominal size, copper alloy, nickel chromium plated finish waste fittings including S&F of fittings and brackets, sealing gap between wall and table top basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste fitting etc with silicone sealant complete all as specified and as directed.

Supply & fixing in repair 10 ltr capacity, low level, symphonic type, white twin flushing cistern conforming to as per IS 7231 :1994 with intel, ball valve, float and handle including brackets and 40mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed.

S&F vitreous china squatting pan "Orissa" pattern of size 580x440mm white with integral foot rests(excluding flushing cistern and flush pipe) with 'P' or 'S" trap fron or back inlet etc including connection to trap tand flushing pipe and provision of cement concrete bedding complete all as specified and as directed in repairs including demolition of existing one.

Supply & fixing in repairs white vitreous china wash down water closet pan floor mounted type including flushing cistern of size 645x355x675mmm with "P" of "S" trap, plastic water closet seat cover (soft landing) and mild steel chromium plated or aluminised hinging device, including making all necessary connections etc complete all as specified and as directed. Make : Cera Cat Part No S1013201 or techno commercially equivalent as listed in List of Makes as approved by the GE.

Supply & fixing in repairs vitreous china wash down water closet pedestal pattern white excluding fixing bolts, including flushing cistern and flush pipe complete but including PVC seat cover with aluminium/PVC hinging devices & etc complete all as specified and as directed. Make : Hindware cat part no 20044 or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F in repair 15 mm bore fancy type bib taps cast copper alloy 15 mm bore with fancy chromium plated screwed down , screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make: CERA Cat part No. F 1015151 or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F in repair 15 mm bore fancy type bib taps long body (two in one) cast copper alloy 15 mm bore single handle and wall flange with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. Make : CERA Cat Part No F-1015163 or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F in repairs 15mm bore stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union complete all as specified and as directed.

S & F in repair 15mm bore PVC Connection with PTMT nuts of length 600 mm complete all as specified and as directed

&F in repair 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions complete all as specified and as directed. Make: Cera Cat part No.F-1015201 or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

Supply and fixed for central hole basin mixer, cast copper alloy with capstan head, chromium plated screwed down, high pressure with or without lettered "Hot" or "Cold" with long screwed shank and fly nuts screwed for iron pipe of 15mm bore complete all as specified and as directed. Make: CERA Cat part No. F-1012451 or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F Toilet Paper Holder chromium plated, including all necessary fittings, connections etc. complete all as specified and as directed. Make : Jaquar Cat Part No ACN 1151N or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed.

S&F in repairs Towel Rail 600 long chromium plated, including all necessary fittings, connections etc. complete all as specified and as directed. Make : Cera Cat Part No F5003103 or techno commercially equivalent as listed in List of Makes as approved by the GE.

S & F of Towel Ring Round chromium plated , including all necessary fittings, connections etc. complete all as specified and as directed. Make : Jaquar Cat Part No AQN 7721 or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F PVC mirror cabinet of size 350x450 mm complete all as specified and as directed. Make : Cat Part No 551 of Prayag or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F in repairs stainless steel soap dish complete all as specified and as directed.

S&F in repairs of Chromium plated over head shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified. Make : Cera Cat Part No. F7010213AB or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F of 15 mm Brass CP single lever Wall mixer long body three in one with arrangement for both telephonic shower and overhead shower with bend pipe and connected fittings for mixing hot & cold water screwed down for iron pipe. Make : Cera Cat Part No. F-1003403 or techno commercially equivalent as listed in List of Makes as approved by the GE.

S&F in repair stainless steel (AISI-304 grade) square grating with frame of size 150 x 150 mm complete all as specified and as directed.

M&L for cement concrete type C-2 1:3:6, using 40mm graded stone aggregate as in surface channel complete all as specified and as directed.

M&L for double nosing and stepping granite stone 15 mm thick of colour as approved as in treads of stair case set and jointed in neat cement slurry over and including 10 mm thick screed bed for laying floor finishes in cement mortar 1:4 complete all as specified and as directed. Note: Single piece stone shall be provided for treads and no jointing of pieces.

S&F of curtain rod of stainless steel 25 mm dia chromium plated with fixing brackets, stop, rollers etc, clamps etc. complete all as specified and as directed.

M&L for Stainless Steel (SS) framed work such as Stairs railing (framed) including stringers, treades, landing, balusters, hand rails etc in Kg including clears, brickers, etc of Ornamental stainless steel of grade 304 as approved design / drawing etc complete all as specified and as directed. Note: Design and pattern shall be approved by Engr-in-Charge /GE at the time of execution of work.

S&F for 3mm thick Poly Carbonate sheet (Compact clear / Bronze sheet) such as grills , gratings, chajja etc. fixed with self tapping screws or nut and bolts complete all as specified and as directed.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten/ conduit/ gutties/ wooden boards/ switches/ sockets/ regulators/ light fittings etc and separating the serviceable items like fan regulators and light fittings for re-use under respective items and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes complete all as specified and as directed.

M&L for point wiring complete for one power point for one metal plug & socket for AC or one socket for geyser point on independent board with 4.0 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 4.0 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, including cutting chases of existing wall for conduits and fixing for Metal Plug and socket boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be done through proper size copper/brass thimbles complete all as specified and as directed.

M&L for point wiring with 1.5 sqmm single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with multistranded copper conductor with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI Marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI Marked) with proper colour coding as earth continuity conductor connected to common earth dolly, modular sheet steel sunken terminal box of appropriate size suitable for modular switch/ fittings concealed in walls, with modular back plate, top cover fixed flush to wall for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles complete all as specified and as directed for the following :-

One light point controlled by one way switch 5/6 Amps complete all as specified and as directed.

One ceiling fan/exhaust fan point controlled by one way switch 5/6 amps complete all as specified and as directed.

One socket out let 5/6 amps point on the independent board complete all as specified and as directed.

One socket out let 5/6 amps point on the same board complete all as specified and as directed.

One bell point controlled by one way switch 5/6 Amps complete all as specified and as directed.

One light point controlled by two way switch 5/6 Amps complete all as specified and as directed.

All as per item No 121 above but wiring with 2.5 Sqmm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified and as directed

S&F of Modular switch, single pole, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, Two way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular switch, single pole, one way, 16 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 5 Pin, 6 Amp, 2 Module, 230 volts, ISI marked complete all as specified and as directed.

S&F of Modular shuttered Socket outlet 6 Pin, 6/16 Amp, 2 Module, 230 volts, (ISI marked) complete all as specified and as directed.

S&F of Modular bell push, one way, 6 Amp, 1 Module, 230 volt, ISI marked complete all as specified and as directed.

S&F of stepped type modular electronic fan regulator 120 watt 2 module suitable for 1200/1400 mm sweep energy saving fans, ISI marked complete all as specified and as directed.

S&F Call bell Ding dong, 230 Volt single phase complete all as specified and as directed.

S&F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and as directed.

S&F LED white glass Lamp 1x9 Watt 230V Base-22 complete all as specified and as directed.

S&F in ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and as directed.

S&F IP 20, class I, LED light 1X20 W (or nearest next higher wattage) (4feet), 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified. Make : Havells, Cat Part No. EDURALINEARNEOBS20WLED865SPCWH or techno commercially equivalent as listed in List o Makes and as approved by the GE.

S&F IP 20, Class I, LED Mirror light fitting 1 x 10 W, (or nearest next higher wattage) 5700 K, wall /Surface mounted with aluminium housing 2 feet long, integrated type, with high efficiency PMMA diffuser, integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 95 lumens/Watt, power factor >/ 0.90, operating range – 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/square blocks, screws etc complete including 01 No 10 W LED lamp with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size including necessary taking down the old unserviceable fitting complete all as specified. Make : Havells, Cat Part No. EDURALINEARNEOBS10WLED865SPCWH or techno commercially equivalent as listed in List of Makes and as approved by the GE.

S&F of Bulk head luminaire suitable for 10 Watt LED (or nearest next higher wattage) light IP66 grade, luminaire efficiency not less than 120 lumens/watts with and including 10 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor from ceiling rose to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified and as directed.

Fixing only LED Tube light of any watt on wall/surface mounted fixed with 02 Nos of PVC round/ square blocks, screws etc complete all as specified and as directed.

S&F of Decorative wall light fixture made up of polycarbonate suitable for 15 Watt LED retrofit of type B-22 base, IP66 grade, with and including 15 watt LED (or nearest next higher wattage) lamp and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified. Make : Havells, CAT No. LHFOECE1TZ1B014 or techno commercially equivalent as listed in Makes of List as approved by the GE.

S & F Energy saving new generation environmental friendly long life versatile pressure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete including removal of old unserviceable fitting complete all as specified and as directed. Make : Havells, Cat Part No ENDCITYLITPLAT+SL35WLED757SASYBOPCWOSPD or techno commercially equivalent as listed in List of Makes and as approved by the GE.

Taking down carefully ceiling fan from its original position and refixing / hanging after B/R plaster work complete all as specified and as directed.

M&L for painting to ceiling fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc complete all as specified and as directed.

Material and labour for concealed sub-main wiring alongwith earth wire of size of 10 sq. mm earth wire, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, including taking down old unserviceable aluminium sub main wiring complete all as specified and as directed. Note : Two runs of 10 sqmm conductor for main and one run of 10 sqmm conductor as earth wire with proper colour coding including one run of PVC conduit shall be measured as one unit length. Connections of cables wit MCBs or bus bar shall be done through appropriate size brass/ copper thimbles.

S & F of MCB, DB Vertical TPN, 415 volts 4 ways (8+18 WAYS), DOUBLE DOOR, IP-43, with MCCB Incomer, metal door, rated bus bars, earth bar, neutral links complete incl. blanking plates as required & fixed flush to wall/other surface complete all as specified and as directed.

S&F Sheet metal enclosure for 4 way Distribution Boards (DB’s), double door, Triple pole & neutral with 200 amps rated bus bar, 415Volt IP-20 protection suitable for fixing MCB"S/isolators with and including taking down old one complete all as specified and as directed.

Supply and fixing of moulded case circuit breaker (MCCB) four pole Adjustable type 415 volt, 50 Cycles, 125 Amps of breaking capacity 36 KA after and including taking down / dismantling of old existing unserviceable one complete all as specified and as directed.

S&F MCB, triple pole & neutral 63 amps, 240 volts, ‘C’ curve, 10KA complete all as specified and as directed.

S&F MCB, single pole & neutral, 32 to 63 amps, 240 volts, ‘C’ curve, 10KA all complete with and including taking down old unserviceable one complete all as specified and as directed.

S&F MCB, single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete with and including taking down old unserviceable one complete all as specified and as directed.

M&L for sheet metal enclosure fabricated out of 2.0 mm thick CRCA sheet, totally enclosed type, dust & vermin proof, with suitable sized supporting MS angles & suitable openings at top & bottom for entry of outgoing / incoming cables, fixed with nuts & bolts & front side openable with hinged shutter with suitable locking arrangement duly painted with 2 coats of powder coated paint over a coat of red oxide primer (spray paint) with minimum dimensions (90 x 75 x 20 cm ) flush to wall for incorporating 01 No TPN DB, 04 Nos electronic meters etc complete all as specified and as directed.

M&L for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised wire 4.00 mm earth lead by means of nuts, bolts, check nuts and washers including 15 mm bore galvanized iron pipe, medium grade for protection of earth lead upto the length of 7.5 meter towards test terminal and 20 mm bore galvanized iron pipe, medium grade for watering, and providing of charcoal and common salt in alternate layers, including necessary earth work in any type of soil and including PCC pit in PCC 1:2:4 with provision of wire mesh and funnel, and PCC cover complete all as shown in electrical plate No 3 of SSR Part- I including testing on complete all as specified and as directed.

S&F exhaust fan with louvers 250 mm sweep (Plastic rust proof Body and blade), BLDC Fan, energy efficient, AC single phase 240 volts, 50Hz,, Air Delivery – 860 CMH and connecting up complete including built in louvers and provision of 3 core flexible multistranded copper conductor of size 0.75 Sqmm from ceiling rose to fan complete all as specified and as directed.

S&F exhaust fan 300 mm sweep MS body with antidust painting, 3 blade with motor and double ball bearing, 1320 RPM, single phase 230/240 volts copper wounds, Air delivery -1600 CMH complete with all accessories as bird guard/ louvers shutters etc including making connections with 3 core flexible multistranded copper conductor of size 0.75 Sqmm run through flexible pipe all as specified and as directed including cutting holes and making good the disturbed surfaces of walls in CM(1:4) and finishing the surface as per existing color scheme complete all as specified and as directed.

S&F epoxy powder coated sheet metal enclosure with socket plug top and MCB, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 32 Amps, 240 Volts, C Series current carrying capacity 10 kA, including necessary connection complete all as specified and as directed.

S&F of Bulk head luminaire with B22 base holder suitable for 9 Watt LED inverter type bulb light IP66 grade, with and including 9 watt LED (or nearest next higher wattage) lamp (LED Bulb with B22 base 900 Lumens in normal mode and 450 lumens in power back up mode, charging time 8-10 Hrs and around 4 Hrs Power backup with inbuilt surge protection of 3 KV) (or nearest next higher wattage) and connecting up with and including PVC insulated 3 core of size 0.75 Sqmm copper conductor from ceiling rose to terminal block of light fitting including necessary taking down the old unserviceable fitting complete all as specified and as directed.

Taking down electric meter three phase any capacity/size disconnecting electrical connections and refixing the same complete all as specified and as directed.

S&F non-metallic rigid PVC medium grade 20mm dia conduit and conduit accessories (ISI Marked) concealed in wall including cutting chases etc complete all as specified and as directed.

S & F Post top lanterns 20 watt LED light fitting ,new generation, energy saving, environmental friendly, longlife with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source, spun aluminium canopy, with opal/clear acrylic diffuser and complete with all accessories internally prewired including connecting up with three core twisted flexible copper conductor cable up to ceiling rose and necessary mounting arrangements complete all as specified and as directed.

M&L for PVC insulated unarmoured copper conductor cable 4 sqmm 2 core complete all as specified and as directed

Taking out old unserviceable GI Pipe of any size from site complete all as specified and as directed. Note : The Excavation and earth work shall be measured and paid separately under relevant item of Schedule.

Supply and lay 25mm dia pipe galvanized, “Medium grade”, including fittings 25 mm fixed complete to walls and ceiling or laid in floor complete all as specified and as directed.

Supply and fix 25mm dia gun metal, globe Gate Valves with iron wheel head of 25 mm dia bore complete with all accessories complete all as specified and as directed.

M& L for cutting existing GI pipe alteration or addition of 40/50 mm dia bore for inerstion of reducer Tee complete with all accessories complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up / laying under ground electric cable complete with all accessories complete all as specified and as directed.

Returning, filling in, including spreading leveling watering and well rammming in layers not exceeding 25 cms in depth complete with all accessories complete all as specified and as directed.

Taking out old unserviceable cable of any size carefully from trenches ofter disconnecting electric connection, GI pipe protection, with and including separating serviceable bricks & set aside and removing un-serviceable bricks from site complete all as specified and as directed. Note : The Excavation and earth work shall be measured and paid separately under relevant item of Schedule.

Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded, galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 50 sqmm 3.5 core with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete all as specified and as directed. Note: Earthwork & Excavation, GI pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule 'A'.

Supply and laying sub class B bricks of old size for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed.

M & L for horizontal boring across the existing road without disturbing the road surface for inserting 50mm GI pipe complete all as specified and as directed. Notes : (a) Removal of surplus soil shall be deemed to be include in the unit Rate. (b) GI pipe will be measured and paid separately under relevant item of Schedule 'A'.

M&L for 50 mm bore steel tubing light grade ISI marked for protection of cable including necessary joints complete all as specified and as directed.

Removing excavated material (soil) n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed.

Supply and fixing of moulded case circuit breaker (MCCB) four pole Adjustable type 415 volt, 50 Cycles, 125 Amps of breaking capacity 36 KA after and including taking down / dismantling of old existing unserviceable one complete all as specified and as directed.

M/S MOHAN KUMAR BANSAL (BID ID -3122893)

Hanuman Prasad Agarwal (BID ID -3119926)

M/S NIKITA ENGINEERING CO (BID ID -3122874)

SHRI MRITYUNJOY KAR (BID ID -3123158)

BHARAT ELECTRIC (BID ID -3119931)

L. B. SHARMA (BID ID -3123646)

R K AGARWAL (BID ID -3123886)

PRAVESH KUMAR (BID ID -3123736)