SPL REPAIR FOR REPLACEMENT OF BER ACs AT WARCEN AND OTHER SANCTION WORK UNDER THE AREA OF AGE B/R-I AND B/R-II OF GE (ARMY) No 1 JODHPUR

Amount

Taking down carefully Old U/S ductable Split AC of Capacity 7.6 Ton and 5.5 Ton including Copper Duct b/w Outdoor and Indoor uinits, Drainage pipe, etc transporting to AGE E/M store Yard deposited to store, making Good to disturbed surface , complete all as specified and directed.

Taking down carefully Old U/S Split AC of Capacity 3/3.75 Ton including Copper Duct b/w Outdoor and Indoor uinits, Drainage pipe, etc transporting to AGE E/M store Yard deposited to store, making Good to disturbed surface, complete all as specified and directed by Engr-in-charge.

Supply, installation, Testing and Commissioning of New Ductable Split AC of Capacity 7.6/8.5 Ton or Nearest higher size available complete with blower section with motor and drive, DX coil, motor mated hermatically sealed Scroll Compressors, centrifugal blower for evaporator, filter and thermostatic control , wired microprocessor control panel, all the items enclosed in an attractive sheet metal cabinet complete with Copper Refrigerant piping of appropriate size (suction & liquid) above alongwith Puf Insulation as per site requirement, charging/filling of Refrigerant gas of approved quality with all accessories required for smooth functioning of the equipment, complete all as specified and directed. Note:- (1) Rates are including of copper tube ie. size and length of copper tube as per site requirement. (2) AC's should be install by OEM check list.

All as per item No. 3.00 here-in-above but capacity 5.5 Ton

All as per item No. 3.00 here-in-above but capacity 3.0/3.75 Ton

Supply, Installation of Microprocessor based Communiocation 4.0/2.5 Sqmm copper cable as per site requirement interconnecting outdoor unit to indoor unit.

Supply, laying, fixing, testing & commissioning of drain pipes with 6 mm thick nitrilerubber tube installation complete with all necessary fittings such as elbows, tees, reducers etc and supports such as U-clamps etc complete all as specified and directe.

Supply, installation, testing of site fabricated sheet metal retangular ducting wih all supports hangers, vanes, etc, complete all as specified and directe.

M&L for sub main wiring (concealed) complete with four single core 6 Sqmm FR LS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 25 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 6 Sqmm FRLS PVC insulated unsheated stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface, complete all as specified and as directed. Note: 5 runs of 6 sqmm&one run of PVC conduit shall be measured as single unit

M&L for sub main wiring (concealed) complete with four single core 10 Sqmm FR LS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 25 to 32 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 10 Sqmm FRLS PVC insulated unsheated stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface, complete all as specified and as directed. Note: 5 runs of 10 sqmm & one run of PVC conduit shall be measured as single unit

Earthing complete with galvanized steel earth plate electrodes 600x600x6 mm thick buried directly in ground eath (earth pit not less 2.25 m deep below ground level) with top edge of the plate not less then 1.5 mtr below normal ground level connected to galvanized iron earthing strip 32mm x6mm thick by means of bolt nuts check nuts and washers of galvnised iron or steel all as specified & shown in electrical plate No.5 of MES SSR part-I connected to earth test point as specified and testing on completion including provision of 40 mm dia light grade pipe & watering pipe shall be 20 mm bore medium grade including all excavation & earth work in any type of soil incl PCC for pit (1:3:6) type C-1 with RCC cover in PCC(1:2:4) including charcoal , salt funnel GI pipe 40 mm dia light grade up to to 7.5 mtr length ,all as directed at site.

M&L for Earthing strip , galvanised iron strip 32 x 6 mm , burried in ground or fixed to pole/ wall with saddles etc as specified and directed. Earth work if required shall be measured against respective item.)

S&F TPN and earth encolsure with a three pin and earth plug with socket complete with one triple pole & neutral MCB, 63 Amp, ‘B’ curve type, 415 volts, 10 KA complete all as specified and as directed.

S&F MCB TPN, 63 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc, complete all as specified and directed.

Supply, installation, testing and commissioning split type Air Conditioner Electric Driven (Single phase ), cooling Capacity 2.0 Ton BEE 3 Star Rated incl all necessary accessories like copper tubes With insulation puffs. Drainage pipe of Required length as per site Requirement. Stand for mounting the outdoor unit on Wall/roof. Gas charging if required, etc complete all as specified and directed by Engr-in-Charge.

Supply, installation, testing and commissioning split type Air Conditioner Electric Driven (Single phase ), cooling Capacity 1.5 Ton BEE 5 Star Rated incl all necessary accessories like copper tubes With insulation puffs. Drainage pipe of Required length as per site Requirement. Stand for mounting the outdoor unit on Wall/roof. Gas charging if required, etc complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130 V to 310 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA, complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 130 V to 310 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4 KVA, complete all as specified and directed.

M&Lfor sub main wiring with PVC insulated and unsheathed 2x 6 Sq mm single core multistrandred copper conductor FRLS cable passing through in and including PVC conduit of 25 mm dia, concealing in walls (by means of chasing including making good existing surface and matching existing surface ) ISI marked and conduit accessaries fixed on surface of wall, ceiling etc, making good the distrurbed surface, incl 6 Sq mm single core copper conductor FRLS cable PVC insulated and unsheathed as earth wire, complete all as specified and directed. Note :- Two runs of cable 6 Sqmm FRLS Cable and One run of 6 Sqmm FRLS Cable along with 25 mm dai conduit shall be measured as one unit length.

S&F MCB SP 20 Amps.Breaking capacity 10KA 'C' curve contirming IS/IEC 60898-1 2002. intregrated label holder. Sliding bottom clamp. IP 20 protected terminal, sliding Shutters, 240 Volts. 50 Hz including making necessary incoming nad outing electrical connection with suitable size of copper lugs etc. And all as Specified & directed by Engr-in-charge.

M&L for Metal clad box complete with plug top and MCB SP 20 Amps 240 V, complete all as specified and directed.

Supply, install & Testing OPEC DHC 90 SS (IS)- Island Chimney, Stainless Steel Finish, Heavy Duty Baffle Filter, Auto Clean TechnologyOPEC DHC 90 SS (IS)- Island Chimney, Stainless Steel Finish, Heavy Duty Baffle Filter, Auto Clean Technology, complete all as specified and directed.

M&L for Modular Point wiring (Concealed) using approved colour coding as per IS Red/Yellow/Blue, Black and green for single phase circuits) with multi stranded copper conductor 2.5 Sqmm nominal cross area single core PVC insulated and unsheathed FRLS cable 1100 Volts grade ISI 694 marked with valid CML No. in and including medium grade PVC concealed conduit of dia not less than 20mm and conduit accessories ISI marked with valid CML No. ( IS 9537 -1983 for wall/roof /floor etc with pressed flush metal boxes covered with inner plates & outer plates etc suitable for mounting of Modular switches & sockets including PVC insulated multi stranded copper conductor FRLS 2.5 sqmm nominal cross sectional area single core FRLS cable as earth continully conductor to commonearth and connecting to earrth dolly complete all as specified and directed for 15 A Independent power point controlled by one 15 Amps modular Switch etc, complete all as specified and directed.

S&F Modular switch flush type single pole one way 16 Amp ISI Marked, complete all as specified and directed.

S&F Modular socket outlet 2 in 1, 6 pin, 5 and 16 amp flush type, 230 Volts ISI Marked, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance out side MD land complete all as specified and as directed.

M&L for Plain cement concrete 1:4:8 type D-2 by using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed .

M&L for PCC 1:2:4 type B1 Mix using 20mm graded stone aggregate as in hold fast iron fixing, pilasters, buttresses,coulmn, pillars, boundary pillars, coping,etc and the like edge slightly rounded or chamfered edges including necessary form work , complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles (premium quality) of size 6 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm (size & shape, shade and pattern as approved by GE), as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including M&L 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for glazed colour ceramic tiles (premium quality) of size 350X450X7 mm /300X600X7 mm, as in vertical surface such as i.e. dado/skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over & including M&L 10mm thick backing coat in CM (1:4), (including Highlighter pattern), complete all as specified and directed.

Demolition of brick / block or stone / boulder masonry walling built in cement mortar including all quoins arches pillars etc and removal unserviceable materials, debris, rubbish to out side MD land complete all as specified and as directed.

M&L for squarred rubble walling Jodhpur type regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6 complate all as specified and directed.

All as per item No 32.00 here-in-above but except stone , complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:4 finished even and smooth without extra cement on stone wall surface mixed with WPC, complete all as specified & directed.

M&L for 15 mm thick rendering in CM 1:6 finished even and smooth without extra cement on stone wall surface complete all as specified & directed.

M&L Rendering 10 mm thick CM (1:3) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth, complete all as specified and directed.

M&L Preparation of new plastered or un-plastered surfaces of walls and applying two coats of cement base paint over & including M&L single coat of chalk white complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-0 (using 12.50 mm graded crushed stone aggregate), as in base course, to receive floor finishes, complete all as specified & directed.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per item No. 29.00 here-in-above, but area of tile exc 0.18Sqm but not exc. 0.38 Sqm, complete all as specified and directed.

All as per item No. 42.00 here-in-above, but as in skirting/dado with 10mm thick backing coat in CM 1:4, complete all as specified and directed.

M&L for Elevated 3D colour stone wall tiles of size 300x450x10/300x600x 10mm thick, laid in vertical surface dado/skirting joint free etc, set and jointed in neat cement slurry and pointed in coloured tiles to match the shade of tiles including 10mm thick rendering in CM 1:4 over stone masonary surfaces finished even & rough to receive tiling etc,complete all as specified and directed.

All as per item No. 35.00 here-in-above, but 10mm thick rendering, complete all as specified and directed.

M&L for preparation of newly/old plastered or unplastered surfaces of wall and applying with 1.5-2.0 mm thick wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of oil bound distemper (shade or tint as approved by GE) over & including one coat of primer on walls complete all as specified and as directed

M&L for 16 to 18 mm thick (telephone black shade) granite stone, as in cooking plateform, oval type WHB counter, sink, window cill & etc. machine cut, (table rubbed and polished) best quality as per sample, including & over 20 mm thick screeding in CM1:3 including rounding & double mouldlng with jointless finish of the edges, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.providing suitable dia hole in the slab for the gas pipe, complete all as specified and as directed.

M&L precast cement concrete block masonry using PCC 1:2:4, type B-1 solid blocks, 10 cm in width and setting in cement mortar 1:6, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed.

M&L for carrying out water proofing treatment for roofs in the following stages - (i) Rendering 15mm thick in cement mortar (1:4), mixed with integral water proofing liquid all as per manufacturer's instructions over concrete surfaces finished even and smooth with out using extra cement. Note: (WPC shell be measured separately and paid for under respective item of schedule), (ii) Material and labour for UV stable single component fibre reinforced elastomeric liquid applied waterproofing membrane having solid content of 55% formulated wih PU hybrid polymers and reinforcing acrylic fibres and having sun reflectivity Index (SRI) of 106. The application of the material should be done in three coat (6 hr gap after each coat) on the substrate, applying first self priming coat at ratio of damp proof ultra and water 3:1 then 2 undiluted coat of damp proof ultra obtaining coverage @1 Itr/10 sqft in two coats (10-12 hrs gap between each coat. The vital physical and chemical parameters shall be as under. Min elongationat break of 350%, crack bridging ability of 2.5 mm @650 microns thickness, resists positive hydrostatic pressure of up to 10 bars. The material shall be appliied with brush or roller, complete in all respect as per the direction of Engr-in charge/consultant. Also, proper surface preparation along with covingat corners is must. Note: The work shall be executed by the authorized applicator of the manufacturer only. Note:- 1. The authorized applicator of manufacturer shall be approved by GE. 2. The color of final finish shall be decided by the GE

M&L chequered cement concrete tile 30CM x 30CM x 19 to 20 mm thick with grey cement and pigment set, jointed and pointed in neat cement slurry over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes etc, complete all as specified and directed.

M&L for UPVC Caoted Celuka printed in one of two different colours( with wood grain printed pattern /ivory clour finish) polyvinyl chloride (PVC) sheet frame of width 150mm & 18mm thickness made out of extruded 18mm PVC sheet and joined with suitable Cement Solvent adhesive and screw.The frame shall be fixed to the wall using 75mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 3 Nos. of screws to be provided for each vertical member & minimum 2 Nos. for horizontal member etc, all as per manufracturers specifications, complete all as specified and as directed.

M&L for 18 mm thick solid PVC sheet UPVC Caoted Celuka printed in one of two different colours( with wood grain printed pattern /ivory clour finish) as in kitchen cabinet shutters ,all round body of cabinets , shelves ,drawers etc cut to required size jointed with solvent cement & steel screws etc complete all as specified & directed .

Extra over solid PVC sheet for fixing 18 mm width & 2-3 mm thick PVC coloured lipping of approved design & colour fixed with solvent cement or headless nails, complete all as specified and as directed.

S&F '0' degree clip type self closing hinges for cabinets fixed with cadimum coated screws, complete all as specified and as directed.

S&F 75mm size bright finished chromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabint drawers, complete all as specified and as directed.

S&F magnetic catches for cabinets of size 50 mm complete with striking plate & magnetic stud complete all as per approved smaple, complete all as specified and as directed.

S&F drawer runners folding type with guide channels & sliding channel with approipiate ball bearing/ rollers etc complete to obtain smooth movement of the drawers, complete all as specified and as directed.

M&L for stainless steel tray as per trade pattern of various sizes for drawer to keep the kitchen utensil as directed by Engineer-in-charge, complete all as specified and as directed.

Taking down shutter of any description, exc. 1 Sqm but n exc 2 Sqm each complete all as specified and directed.

M&L factory Made flush shutters, 35 mm thick solid core with block board core construction as per IS 2202(part-I, 1999), both side decorative type. The stiles & rails shall be with out any joint and made with non- coniferous timber hard wood (Hillock/ Mirantee/ Bosum/ Benteak) with moisture content not less than 12% as per IS. The face panel comprising of ply wood or cross band and face veneers shall be glued by hot pressed process. The over all finished thickness of face panel shall not be less than 30mm while the thickness face veneer shall not be less than 0.6 mm complete all as specified and directed.

M&L 35mm thick factory made 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I Section 8 Clause 8.24 (a) complete all as specified and as directed.

S&F of aluminium anodized,tower bolt 200 mm long complete all as specified and directed.

S&F aluminum anodised handle extruded section of size 150mm long complete all as specified and directed.

S&F of aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long complete all as specified and directed.

S&F of mild steel butt hinges 100 mm size complete all as specified and directed.

S&F 100mm size single action door spring hinge complete all as specified and directed.

S&F floor door stopper of alluminium alloy body and toungue anodised with hard drawn steel spring 140mm long complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm with necessary fitting on steel/ wooden surface complete all as specified and directed.

S&F ONE PEACE vitreous china wash down EWC with and including inbuilt flush tank with seat cover fixing accessories etc complete all as specified and as directed.

Surface excavation n. exc. (not exceeding 30 cm deep and avg 15 cm deep) and getting out in any type of soil complete all as specified and directed.

Surface dressing n exc 15 cm deep over any type of soil, complete all as secified and direceted

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in hard/dense type of soil, complete all as specified and as directed .

Returning, filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in soils complete all as specified and directed.

Removal of excavated material soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

M&L plain Cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) as in 40mm thick damp proof course to horizontal or vertical surfaces in including necessary formwork etc, complete all as specified and directed.

M&L precast cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in solid block masonry or slab 10cm thick with plain, joints setting in cement mortar 1:6, complete all as specified & directed by Engineer-in-charge.

M&L Hardcore of gauge not exceeding 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, compacting with power roller, complete all as specified and as directed.

M&L for 100mm thick Plain cement concrete 1:4:8 type C-2 by using 40 mm graded crushed stone aggregate as in sub base of foundation, complete all as specified and as directed .

M&L for 75mm thick Plain cement concrete 1:3:6 type C-2 by using 40 mm graded crushed stone aggregate as in sub base to receive floor finish, complete all as specified and as directed .

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 80mm thick with 6 mm thick top layers of anti abrasive material of M-40 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Supply and laying machine / factory made kerb stone of M-25 grade,at or near ground level, cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, complete all as specified and directed.

Use and waste of formwork to sides and soffits of slabs,suspended slab such as roof slabs, floor slabs,landing etc n. exc. 200 mm thick and similar works fair finished surfaces of concrete complete all as specified and directed.

M&L RCC nominal mix type B1, 1:2:4 (20mm graded aggregate) as in slab supported on wall,beam,columns in floors,roofs,landing,balconies,canopies, deck slabs, roof slab, chijja,shelf and in shelve etc complete all as specified and directed.

S&F mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

All as per item No. 41.00 here-in-above, but as in skirting/dado with 10mm thick backing coat in CM 1:4, complete all as specified and directed.

S&F of aluminium anodized,tower bolt 150 mm long complete all as specified and directed.

M&L 40 mm thick PCC (1:2:4) type B1 using 20mm graded stone aggregate as in floor , hard standing flooring finished even and smooth without using extra cement complete all as specified and directed.

M&L 50 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate laid in alternative bays as in plinth protection including finishing the surface even & fair & filling the joints with mastic filling i.e one part of bitumen 85/25 and 3 parts of sand by weight in 2 mtr interval, complete all as specified and directed.

Supply only Integral water proofing compund, ISI Marked, complete all as specified and directed.

M&L for cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate), as in foundation, post, sub base, mass concrete etc, complete all as specified and directed.

Earth filling under floors or in foundations including watering and consolidation, spreading and levelling in layers n.exc. 25cm thick and well ramming including watering as rerquired etc, complete all as specified and directed.

Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface n exc 20mm and dressing face beds and joints, complete all as specified and directed.

M&L for mild steel frame work in trusses/tubular trusses purlins, posts etc complete using MS angle iron, MS Hollow Square or rectangular sections,flat irons, special shaped washer etc complete incl necessary welding cutting to shape size and designe & hoisted & fixed in position, incl Dismantling cast iron work of any description complete all as directed & specified .

M&L for pre painted galvatume aluminium zinc GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering any shape (stright/curve) fixed with J or L hooks , incl Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc, complete all as directed & specified .

M&L for Plain, galvanised, mild steel sheeting .63 mm, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, complete all as directed & specified .

M&L Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges 1.25 mm thick 150mm dia sheet, complete all as directed & specified .

S&F for Anodised aluminium snap grid frame work ( 605x605 mm) for false ceiling all as specified and incl dismentling of existing false ceiling, etc complete, as specified and directed.

S&F Exposed metal frame ceiling with calcium silicate board 6mm tks of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately), complete all as directed & specified .

S&F for tinted glass 5.5mm thick, ordinary quality and glazing with oil putty in squares exceeding 0.5 Sq.m in each pane etc fixed to aluminium frame work including rubber beading, complete all as specified and as directed.

S&F Anodised aluminium frame powder coated (Thickness of powder coating not less than 50 micron) for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified.

S&F Anodised aluminium door/window/ventilators shutters powder coating of any colour (Thickness of powder coating not less than 50 micron) , aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed.

M&L preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over & including M&L single coat of red- oxide, zinc chrome primer complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint of any tint complete all as specified and as directed .

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed.

Supply and laying machine pressed / factory made chamfered edge cement concrete rubberised interlocking paver block, 60mm thick with 6 mm thick top layers of anti abrasive material of M-35 grade with any colour, design & pattern, & size/ shape, as approved by GE as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness made by table vibratory method using PU mould, laid in required colour & pattern over and including M&L 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

Excavating in post holes (of similar holes) each n. Exc. 0.50 cum getting out in any type of soil, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. Exc. 50m and making good surface complete all as specified and directed.

S&F mild steel sections like angle, flat etc in post and struts in fencing or with swan neck,, including cutting top to shape as directed,drilling holes,notching for wire etc;flat iron fillets (for securing wire mesh etc including all necessary drilling,bolting or riviting etc confirming to Fe-290Gde E-165 complete all as specified and as directed.

M&L for rolled mild steel work confirming to Fe 410-W, Grade-E- 250, Quality-A as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings [exclusive of steel sheeting or other covering, running rails and guides] and hanging, also fastening and fixing complete all as specified and as directed.

M&L for Iron plates, any size, of galvanised iron sheet 3mm thick, fixed with galvanised screws in iron gate

M&L for welding Cast iron designer pieces like spikes , spiral patterns & moulding pieces etc with intricate designs to the steel gate frame work complete all as specified & directed .

M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one end and scrfewed the other, each screwed end to be fitted with washeres and one haxagonal or square nut not exceeding 5cm long with daia of neck 5 to 11 mm complete all as specified and directed.

Supply only Chain link MS galvanised fencing any size or type (The max. size of mesh does not exc 100mm x 100mm and dia of wire exc 4mm.) as approved by G.E. Note:- BOO will consitute by GE to determinate the weight of chainlink.

Fixing only mild steel galvanised chain link fencing including line wires, any mesh size and type to any type of standards, rails, straining bolts etc including provn of binding wire if reqd complete all as specified.

S&F mild steel round bars 10mm dia cut to length bent to shape required including cranking bending etc of Gde Fe 410W (Gde E-250) quality A or Fe 290 (Gde E-165) complete all as specified and directed

M&L for preparation of plastered or un-plastered surfaces and applying with two coats of Birla / JK wall care putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces, complete all as specified and as directed.

M&L for fabrication of powder coated (powder coating min 50 micron) aluminium frame work as in frames for aluminium windows with or without rebate or for sliding windows(two track/three track ), ventilators etc with louvers having suitable mechanism for tilting , U shaped fillets for securing Jallies etc & the likes complete all as per sample kept in GE Office & fixed in position complete all as directed. Note : Glass panes in louvers & wire cloth shall be measured & paid for seperately,

S&F for sheet glass 4.8mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3 universal type,suitable for door shutters of 851 to1000 mm in width and of weight between 61 to 80 Kg complete all as specified and as directed.

M&L precast cement concrete block masonry using PCC 1:3:6, type C-1 solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4, straight or curved on plan exceeding 6 m mean radius complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1 : 4 of cement used and finishing even and smooth without using extra cement.complete all as specified and directed. Note -Rate are deemed to be included for scaffolding, trestles, ladders, cradles, etc. necessary for execution of work and protective measures.

M&L Preparation of new plastered or un-plastered surfaces of concrete and applying two coat of synthetic enamel paint over & including M&L single coat of primer complete all as specified and directed by Engr -in-charge

Supply & laying 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall/ceiling with MS clamp or laying floor of suitable size complete all as specified and as directed .

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting gussets plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410-W (Gde E-250) quality -A, complete all as specified and as directed.

S&F Mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged exc 15cm but not exceeding 30cm long of 20mm dia neck bolt , complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles joint free 7 to 8mm thick (Square/Rectangular) area of each tiles exc 0.18 Sqm but n exc 0.38 Sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including over 15 mm thick screed bed or bedding layers in CM (1:4) for laying in floors finishing ,complete all as specified and directed.

M&L for rounding to edges of stones slabs one edge , such as in steps, cooking platform, and other similar situations etc, complete all as specified and as directed.

S&F GI water tubing medium grade, 15 mm bore size, galvanized, with all fittings fixed to wall, ceilings or laid in floors, complete all as specified and as directed.

S&F of CP bib taps 15mm dia, cast copper alloy fancy type, long body screwed for iron pipe or for brass ferrule , complete all as specified and directed.

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

S&F of kitchen plate rack of size 1200mm x 900mm x 250mm made of stainless steel not less than 1 mm thick (SS grade 304) with fixing acessories pvc rawl plugs and screws complete all as specified and directed.

S&F of PTMT waste pipe 32mm dia 900mm long complete all as specified and directed.

S&F of PVC (SWR) floor trap plain with grating including jointing with solvent cement dia of outlet 75mm, complete all as specified and directed.

S&F of 75 mm bore (SWR) PVC bends any radius with access door, complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 by using 40 mm graded crushed stone aggregate as in surface chasnnels and drains etc,complete all as specified and as directed .

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc complete all as directed.

Note:- (i)- Qty's have been clubbed from 8 Nos sanction Job's, whose details as per appx NOTE:- (i)- The contract sum shall be arrived at after duducting amount of schedule of "Credit" from the Total quoted amount

M/S KAUTILYA GARG (BID ID -3371867)

M/S SUMAN ENTERPRISES (BID ID -3366213)