PROVN OF HAY SHED SPECIAL REPAIR TO BLDG NO P01 OF ASCON NODE AND SPL REPAIR TO TOILETS BOTH GENTS AND LADIES AT SUNDERBANI MIL STATION UNDER GE NORTH AKHNOOR

Amount

Taking down old treatment incl paddding, removing existing bitumen felt treatment incl brushing,cleaning top surfaces of roof slab, broming etc complete all as specified.

M&L for rendering 15mm thick cement plaster with cement mortar(1:4) on fair finishes of brick work or concrete surface of roof slab all as specified.

Roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M&L for brushing neat cement slurry with 3.0kg of cement per sq. Metre complete all as specified and directed.

Roof treatment : Water proofing treatment to RCC roof slab including of parapet as under:- (a) First Course : Apply a coat of biruminous primer conforming to IS - 3384 @ 0.40 Kg/Sqm on prepardd surfaces of plaster and After drying of primer apply a coat of hot blown 85/25 penetration grade blown bitumen conforming to (IS-702 @ 1.20 Kg/Sqm on plasterd surfaces. (b) 2nd Course : APP(Atactic Polypropylene) modified polymeric 5 layed 3 mm thick weight not less than 4.0 kg/Sqm with 160 Grams/Sqm non woven polyster made at centre core reinforced laid with 75mm side overlap and 150mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints and changes in direction should be covered with cement mortar 1:3 mixed with SBR latex @200ml/bag of cement and curved before laying of membrane (c) 3rd Course: Apply a coat of ht blown 85/25 grade bitumen conforming to IS-702@ 1.20 Kg/sqm over membrane and dusted with dry sand @ 0.50 to 1 Kg/sqm.

Note:- (i) Roof treatment work shall be carried out through approved manufacture only (ii) If non accesible roof after providing (a) to (c) provide two coat of aluminium paint as per manufacture instructions (iii) Covered filled in PCC 1:2:4 type B0 using 12.5 graded crushed stone aggregate of required radius shall be provided at the junction of roof and vertical surface such as parapet wall/mumty around opening and treatment mentioned above shall be applied followed by a cement plaster 20mm thick in cement mortar (1:6)

Taking down cement plaster from brick or stone walls incl racking out joints hacking for key, scrubbing down with water etc.

M&L for rendering 15mm thick on other than fair faces of brick/concrete or stone masonary surfaces in CM 1:6 finished even & smooth without using extra cement .

M&L for rendering 5mm thick in cement mortar 1:3 finished even and smooth without using extra cement on ceiling surface complete all as specified and directed .

Rendering 10 mm thick on other than for fair faces of brick/concrete or stone masonary surfaces in CM 1:4 finished even & smooth without using extra cement

M & L Preparing new treated surfaces of walls and applying two coats of distemper of emulsion over a coat of chalk whitening.

M&L preparing of new plasterd surfaces of ceiling and apply three coat of white wash on ceilling.

M& L for preparation newly plastered or previously untreated wall surfaces and apply two coats cement base paint over a coat of primer complete all as specified and directed by Engineer -in-Charge.

M&L for preparing old surfaces of walls incl washing rubbing down and stopping of distempered and apply two coat of distempered oil emulsion complete all as specifed

M&L for preparation of old surfaces complete removal of wall existing surfaces and apply two coat of cement base paint in camafloge pattern to walls including two coat of cement primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparing new plastered surfaces of walls and apply three coats of white wash on walls

M&L for preparing new plastered surfaces of walls and apply two coats of white wash on walls

Demolition of stone/brick masonary built in cement/cement lime mortar

M&L for brick work with sub class 'B' brick straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 all as specified

All as per Srl Item No 18 here-in-above but except bricks.

S & F Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down old unserviceable existing tank complete.

Taking up or down steel water tubing and connections of 20mm dia bore.

Taking up or down steel water tubing and connections of 15 mm dia bore

Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete of 20 mm dia bore .

All as srl Item No 23 here-in- above but re-fixing old steel tubing of 20 mm dia bore

Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete of 15 mm dia bore.

All as srl Item No 25 here-in- above but re-fixing old steel tubing of 15mm dia bore.

S&F stop valves cast copper alloy serwed down high pressure , 15 dia bore fixed in repairs.

S&F ball valve high pressure PTMT with epoxy coated aluminium rod & high density plastic ball 20mm dia bore.

Demolition of cement concrete any description and in any postion not otherwise all as specified & directed

M& L for 25mm thick cement concrete type B1 1:2:4 using 20 mm graded aggregate as in sub floor all as per specified & directed by Engr-in-Charge.

M&L for 50 mm thick 75 cm wide PCC type C-1 1:3:6 (using 20mm graded stone aggregate) as in plinth protection laid in bays complete including 75mm thick consolidated hard core of broken stone over rammed earth finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight) complete all as specified and as directed by Engineer-in-Charge. Note :- The rate quoted shall be deemed to include for use and waste of form work / screed strips and to divide the area in panels including hardcore.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store andd rubbish off the premises

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and directed.

M&L Glazed ceramic tile 300 x 200 x 06-7mm thick (coloured) on vertical surfaces such as dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick screed bed in cement and sand mortar 1:4, complete all as specified and directed.

M & L for vitrified cermaic tiles light shade 9-10mm thick ( square or rectangular ) area of each tiles n.exceeding 0.36 sqm floor /skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed in cement and sand mortar 1:4 complete all as specified and directed.

M & L Green Marble work 18mm to 20mm thick (tabel rubbed and polished) in steps of staircase/kitchen platform and like in cement mortar (1:4) inclduing pointing in white cment (1:2) using marble dust with admixture of opigment ot match with marble shade of Green marble including 15mm thick screed bed/base in CM 1:4, roughening/cleaning to existing surface of old concrete floor by pickin, sweeping clean and washing down with water to remove dirt/dust and brushing neat cement slurry with 3.0 kg of cement persqm all as specified and as approved by the GE/Engr-in-Charge.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 m and n.exc 4.00 Sqm each.

Refixing of shutter of any description exc 1.5 and n exc 4.00 sqm complete all as specified and directed by Engr-in-Charge

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) nexc 1.50 sqm complete all as specified and directed.

PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame.and including 50 mm parapet coping all as specified etc.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia thresh old bar and filling hollow of frame of following sizes of frame :-105x60mm.

S & F 35mm thick Flush shutters, solid core with particle board exterior grade as per IS-2202 of 199 (Part-I). Flush door shutter shall be internally lipped as per clause 8.25.2 of SSR-2009 Part-I complete all as specified and directed by Engr-in-Charge.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as a gap insert for top rail and bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S frame welded / sealed to the stiles and nails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at side as per specification and drawings.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing.

M&L for preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide premier.

M&L for preparation of new untreated wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and painting with two coats of synthetic enamel paint over a coat of pink primer.

M & L Plain, solid, straight chowkats and frames made out of 2nd class hard wood, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, supplied and fixed, complete all as specified and as directed by Engineer-in-Charge.

Mild steel springs for doors, 150 mm, ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F 100 mm butt hinges, medium weight cold rolled mild steel.

S&F 75 mm butt hinges, meium weight cold rolled mild steel.

S&F Aluminium handles cast type anodised of size 150mm long ISI marked complete.

S&F Aluminium anodised barrel tower bolt 200 mm, extruded section complete all as specified.

S& F aluminium anodised sliding door bolts round nuckle with hasp and stapple extruded section or cast aluminium alloy 300 mm long complete all as specified.

S&F Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue,nodised,with hard drawn steel spring,fixed in bottom body of door complete all as specified and directed.

S&F stop valves cast copper alloy serwed down high pressure with crutch or butterfly handle 20mm dia bore fixed in repairs.

S&F Vitreous china, wash hand basin (WHB) flat back size 630 x 450mm including pillar tap, waste fittings, bracket all as specified and directed.

S&F PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs.

S&F vitreous china squtting pan "Orissa Pattern" size 580 x 440 mm in any coloured with integral foot rest incl lime motor, 'S' trap and complete all as specified, fixed in repairs.including taking down all as specified.

S&F Vitreous china wash down water closet pan (S-trap) while (size 370x690)mm with seat cover. Hinges and flushing cistern (single Piece) incl in fittings incl making connection to trap and to flush pipe incl fixed in repairs complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts 450 mm long.

S&F Aluminium anodised towel rail 20mm dia 'D' type 50 cm long between flanges .

S & F stainless steel cockraoch traps Single piece in a box size 101 x 101mm with waste hole complete all as specified fixed in repairs.

S& F liquid soap container of PTMT fixed with and including chroumium plated brass screws and wooden/plastic cleats(mm weight 105gms) fixed in repairs complete all as specified and directed

S & F Towel rail 600mm long of PTMT fixed with and including chromium plated brass screw and wooden/plastic cleats (mm weight 190gms) fixed in repairs complete all as specified and directed

S & F Health facuet fixing in pipe fixed in repair etc complete

S&F CP Bib taps, cast copper alloy, fency type ISI marked with wall flange for iron pipe of 15 mm bore and if fixed in repairs complete all as specified and directed

S&F CP Angle valve/concealed stop cock of cast copper alloy (ISI Marked) chromium plated facny type screwed down high pressure with capstain head screwed both ends for iron pipe of 15mm bore incl add if fixed in repairs complete all as specified and directed

S&F Corner Glass shelf assembly (with bracket) complete all as specified

S & F Sheet glass self assembly consisting of 5.5 mm thick sheet glass 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed fixed in repairs .

S&F vitreous china wash basin (white) flat back size 560x430 x195mm including all fitting accessories CP, waste coupling and PVC wate pipe all as specified and directed.

S & F in repair chromium plated fancy tap pillar tap with lift type operating knob and base flange 15 mm bore dia all as specified and as directed

CP Brass wall mixture with Telephonic shower arrangement for mixing hot cold water supply screwed down incl connecting legs & wall flanges for iron pipe 15mm dia bore fancy type in repair complete all as specified and directed.

S&F curtain 19-20 dia aluminium powder coated teak wood texture finish 1mm thick with encl butts hinges of required size including bracket complete all as specified and directed.

S&F Vitreous china bowl urinal flat back, size 465 x 355 x 265 mm, white, with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement martar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing against urinal back in cement fixed in repair all as specified and as directed.

S&F vitreous china urinal, half stall type, white (back or corner wall type) complete including waste pipe, coupling and providing and fixing plugs, bedding urinal against wall in cement martar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing against urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe fixed in repair complete all as specified and as directed.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 m deep in any type of soil and getting out complete.

Removal of surplus soil to a distance no exc. 50 mtr and depositing where directed at a level n exc. 1.50 mtr above the starting point all as specified and directed by Engr-in-charge

Returning and filling including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified

M&L PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in surface channel and drains complete all as specified

M&L Brick work with sub class 'B' bricks , straight or curved on plan half brick thick wall in CM 1:4 all as specified and directed

M&L for rendering 15mm thick Cement Plaster CM 1:4 on fair faces of brick work including finishing surfaces fair and even (without using extra cement)complete all as specified .

M&L for rendering 5mm thick Cement Plaster CM 1:4 on fair faces of brick work including finishing surfaces fair and even (without using extra cement)complete all as specified .

M&L for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including moulds metre/stopped end etc

M&L for precast cement concrete RCC cover 200 mm thick type B-1 (1:2:4) using 20 mm graded aggregate all as specified

M&L for TMT Bar 8mm dia bar and over cut to length bent to shape required including cranking bending hooking ends binding with and including mild steel wire (annealed) not less than steel wire 0.9mm dia or securing with clips and conforming to Fe 410-S and 310-0)

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in any type of soil as directed by Engineer-in-Charge.

Excavation in post holes (or similar holes) in any type of soil, each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified.

M&L Cement concrete in foundations, filling and mass-concrete Type D2, 1:2:4 (using 40 mm graded stone aggregate) as in post hole complete all as specified & directed.

M& L for hardcore broken stone or boulders of gauge n exc. 63 mm but n.exc 100mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 100mm thick 1:3:6 type C-2, using 40 mm graded stone aggregate, as floors including necessary form work finishing cement concrete surfaces even and smooth without using extra cement all as specified and as directed by Engineer-in-charge. .

M&L for machine cut kota stone slab flooring 20-25mm thick as in flooring jointed with grey cement slurry mixed with pigment to match the shade or the slab including rubbing and polishing complete including 20mm thick screed bed in CM 1:4 for laying floor finishes complete all as specified and as directed by Engineer-in-Charge.

S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 including notching, drilling, fitting, riveting and or welding or connecting with bolts and nuts including rivets or nuts and bolts ,providing and fixing cleats fish plates, gusset plate etc and also for wedging , plumbing, turning up and fixing complete all as specified and directed by Engineer-in-Charge.

S&F for mild steel flat iron hold fasts, clamps etc and similar small articles conforming to FE-290 Gde -E-165 complete all as specified and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof overing/ cladding to wall, fixed with self tapping screws incl ridge including dismantlling of existing asbestos cement (corrugated, semi corrugated) sheets as in roof covering including ridges,hips, valleys and flashings etc complete all as specified & directed by Engineer-in-Charge.

M&L for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof overing/ cladding to wall, fixed with self tapping screws incl ridge complete all as specified & directed by Engineer-in-Charge.

S&F Welded steel wire fabric complete to wood or steel members n exc 4 kg per Sqm complete all as specified.

M&L Cement concrete in foundations, filling and mass-concrete Type D2, 1:4:8 (using 40 mm graded stone aggregate) as in sub base complete all as specified & directed.

Machine pressed precast concrete interlocking paver block any shape and size conforming IS 15658-2006 of 80mm thickness M-35 grade over a layer and including 25mm thick sand cushioning complete all as specified and directed.

M&L for rendering 15mm thick cement plaster with cement mortar (1:4) on fair faces of brickwork or concrete surfaces and finished even and smooth without using extra cement with using water proofing compound all as specified and directed. (Note: WPC shall be measured and paid separately)

Supply only Integral waterproofing compound all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified & directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in pane complete all as specified & directed.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified & directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (Minimum weight 60 gms) all as specified & directed.

S&F Salt glazed stoneware gully trap, square or round mouthed type 'P' of size 150x150mm all as specified & directed.

M&L for 150 mm dia SGSW drain pipes grade ‘A’ laid in trenches and jointed in cm 1:1 including concrete bedding and haunching complete all as specified and directed.

M&L for PCC 1:4:8 type D-2, (using 40mm graded crushed stone aggregate) as in bed of drain pipe including packing under, and haunching against the sides of pipes after they are laid and tested for the 150mm dia of pipe complete all as specified and directed.

S&F in repair steel chromium plated round grating 100mm dia, fixed in position in cement mortar (1:3) complete all as specified & directed.

M&L for Disconnecting existing water tank, setting aside (or lowering if required) for repair, cleaning etc and hoisting if required, reconnecting and re-fixing in position all as specified & directed.

M&L for chequerred cement concrete colour tiles 20 cm x 20 cm x 25mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors complete all as specified and as directed by Engineer-in-Charge.

M&L for sand filling under floors or in foundation including watering and consolidation as sand cushioning 25mm thick complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully, copper / aluminium conductor unserviceable / perished point wiring (any type) for light/ fan/ light socket or power socket etc complete with fittings such as switches, sockets, ceiling roses, pendant holders, bracket holder, light fittings, regulators etc, including making good to disturbed surfaces of wall/floor etc, complete, all as specified & directed.

M&L for Sub main wiring with two runs of 6.0 Sqmm single core FRLS PVC insulated unsheathed cable upto and including 1100 volts grade with multistranded copper conductor drawn through in and including PVC surface conduit or casing caping of 20/30mm, 2.0 mm wall thickness (ISI marked) with all fittings and fixing accessories, surface type on walls, roofs etc including one run of 2.5 Sqmm FRLS PVC insulated copper conductor for earth continuity wire in green color including taking down carefully existing copper submain wiring with PVC surface conduit or casing caping and making good disturbed surfaces complete all as specified & directed by Engineer-in-Charge. Note:- Two runs of copper conductor 6.0 sqmm and one run of 2.5 Sqmm copper earth wire including PVC casing caping will be measured and paid as one unit only.

M&L for Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan/bell point controlled by one way switch, complete all as specified & directed.

All as per Srl item No. 115 here-in-above but for one 5 pin 6 Amps socket outlet on same board with other switches.

All as per Srl item No. 115 here-in-above but for one 5 pin 6 Amps socket outlet on independent board.

M&L for point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable 1100 volt grade, single core of 2.5 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling/false ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one 3/5 pin socket outlet 16 Amps controlled by one switch on independent board, complete all as specified & directed. Notes for Srl Item No. 115 to 118 (i) Unit rate includes for cutting chases whereever required and sinking for boxes, making good to walls / floors etc., complete, including white wash / colour wash as directed. (ii) Uniform coding of wiring i.e red / yellow / blue for phase black for neutral and green for earth is to be maintained.

Supply & fixing modular type switch 6 Amps, single pole, 1way,1 module,240V, ISI Marked complete all as specified and directed. Make Indoasian Glint,Crabtree, Havells REO

Supply & fixing modular type switch 16 Amps, single pole,1 way,1 module,240V, ISI Marked Complete all as specified and directed. Make Indoasian Glint,Crabtree, Havells REO

Supply & fixing modular type socket shuttered type 6 Amps- 2/3 Pin combined 2 module,240V,AC ISI Marked Complete all as specified and directed. Make Indoasian Glint,Crabtree, Havells REO

Supply & fixing modular type socket 6 A/16 Amps -2/3 Pin combined shuttered socket 2 module 240V AC ISI Marked Complete all as specified and directed .Make Indoasian Glint,Crabtree, Havells REO

Supply & fix fan regulator modular type electronic, stepped type 100 Watts, 2 module 240Volts,AC ISI marked complete all as specified and directed. Make Indoasian Glint,Crabtree, Havells REO

S&F ceiling rose 5 amp, 3 plates polycarbonate body complete all as specified & directed.

Supply and fixing sheet metal enclosure double door type for DBs single pole and neutral 12 way 240 V with 200 Amp bus bar including blanking plates where required including fixed flush in wall chases wall for fixing DB and making good surfaces to match with existing surface all as specified and directed. Make : Indoasian, Legrand, Schiender, Havells etc.

S&F in replacement MCB, single pole, (SP) 6 to 32 Amp, AC, 10 KA repturing capacity, ISI marked, 240 Volt, 'C' series, including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified & directed by Engineer-in-Charge.

S&F in replacement MCB, single pole & neutral, (SPN) 63 Amp, AC, 10 KA repturing capacity, ISI marked 240 Volt, 'C' series, including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified & directed.

S&F Energy saving 10W LED bulk head luminaires, IP-65, oval shape, surface mounted with all other accessories prewired and making connections with copper flexible twisted twin cord of appropriate gauge and length, 230v, 50Hz complete all as specified & directed. Make. Havells, Cat Part No. RUGBYNEONFT10WLED760SSYMBOPC or equivalent in Philips/ Crompton/ Bajaj

Taking down UNSV flourescent fitting and M & L for LED batten Regal suitable for T8 LED tube incl T8 LED tube crystal glass with very high efficacy suitable for installation in existing T8 fitting with G13 lamp 20 watt 4 ft long all as specified and directed. Make : Havells Part No for batten- REGALBATTENT8UPTO1X22W DSBSWH, Cat Part No- LED Tube T8 : CRYSTAL1213T8DSTL18WLED865SGLASS or equivalent in CG, Philips, Bajaj . Note :- Rate quoted include the cost of both batten and Tube rod T8 and shall match with the batten.

Supply and fixing ceiling fans complete with blades. Down rods, electronic regulator and accessories, 230 volt, 1200mm sweep, min air delievery 210 CFM with service value 6 BEE five star rated with brushless direct current motor (BLDC) incl taking down existing and deposit with MES all as specified and directed.

Taking down old unserviceable Exhaust fan of any type/size from existing location and deposit in MES store yard and Supply and fix exhaust fan single phase metal body, AC 230 Volt, 50 Hz of size 300mm sweep with louvers shouter complete with all accessories including connecting up from ceiling rose to motor all as specified and directed. Make : Havells, Bajaj, Cromption etc.

S&F Earthing of galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr depth below normal ground level) with top edge of earth not less than 1.5 metre below normal ground level, surrounded on all sides by 150mm thick charcoal & common salt starting from ground below earth plate upto 150mm above GI plate in alternate layers connected to and including earth lead wire 4.0mm (8SWG) by means of steel bolts, nuts, check nuts and washers, test point made of GI strip 40x8mm, 10cm long PCC 1:2:4, type B-1 in pit with precast RCC 1:2:4 type B-1 in cover reinforced with XPM not less than 4 Kg per Sqm with 15mm bore GI light grade protection pipe, 20mm bore GI medium grade watering pipe with funnel including charcoal, dust, salt, all as shown in electrical plate No 3 of SSR Part-I (2009) including taking down old existing earthing complete with necessary earth work in any type of soil, removal to a distance not exceeding 50 mtr, including testing on completion, complete all as specified & directed. Note : (a) The cost of earth work, PCC pit of size shown in electrical plate No.3, funnel, watering pipe, wire mesh, charcoal, dust, common salt, 20mm bore medium grade watering pipe & 15mm bore light grade GI pipe as protection to earth lead wire etc shall be deemed included in the unit rate for earthing. (b) After completion, during testing, if the earth resistance equal or less 2 ohms is not obtained, earthing will be regenerated at no extra cost till the desired earth resistance is obtained.

S & F in replacement of 20 Watt LED energy saving light fitting environment friendly long life LED street light made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 with GI bracket made of light grade GI pipe 40 mm dia of 1.2 mtr long bend to shape with 02 Nos of FI clamp 32 x 4mm with suitable size nuts, bolts, washers etc. and making the connection from ceiling rose to fitting with suitable size twin core copper conductor cable complete all as specified and directed . (Make- Havells, cat part No ENDURACITYLITEPLATSL20WLED757SASYBOPC or Bajaj/Philips/Crompton Greaves or its equivalent).

S & F in replacement of 20 Watt LED batten/inverter capacity having charging time 8 hours, driver efficiency > 85% , power factor > 95% and operating voltage 270 volt with suitable size nuts, bolts, washers etc. and making the connection from ceiling rose to fitting with suitable size twin core copper conductor cable complete all as specified and directed . (Make- Halonix/ Bajaj/Philips/Crompton Greaves or its equivalent).

Supply, laying and testing XLPE insulated, electric cable (heavy duty) with stranded aluminium conductor, 1100 volts grade, heavy duty cable, cross-sectional area 25 Sqmm 3.5 core laid in trenches or passing through pipes complete all as specified and directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately)

M&L for 50mm bore Tubes, 'light grade', galvanised, for cable protection fixed on poles or laid in trenches under floor, ducts etc with fixing clamps, nuts, bolts etc complete all as specified and directed.

Brick well burnt locally available sub class 'B' laid over sand cushioning for mechanical cable protection in trenches with width of brick perpendicular to the length of cable, complete all as specified & directed by Engineer-in-Charge.

Sand cushioning to under ground cable, laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete punned to 18cm, complete all as specified and directed. Note:- Punned thickness of sand will be measured and paid.

M/s Mool Raj Romesh Chander