GENERAL Repair works in LI Scheme Refitting of motor pump set starter Pipe line panel board and electrification works etc of Newly constructed pump house at Parakadavu No.2 LI Scheme General Electrical Work

Amount

Refitting of motor pump , pipe , panel etc

OD175701/2022-2023:Supply , conveying , erecting and commissioning of the 400 mm dia MS pipe in Suction/Delivery side having sheet thickness 6 mm and cutting in to required length, facing the cutting edges,painting two coats of synthetic best quality enamel paint over a coats red oxide primer, including conveyance charges to pumphouse and labour charges for loading, unloading,etc.

OD150503/2022-2023:Dismantling the existing MS Suction/Delivery pipe, bend of size 400/450 mm piece by piece after providing scaffolding supports and stacking at the yard

OD176002/2022-2023:Charges for demolishing the existing concrete floor using special tools and deposite the demolished concrete blocks outside the pump house

OD152847/2022-2023:Supply and providing the rough cut flange ring joint 15 mm thick for 400 mm MS pipe after facing the cutting edges of flange rings neatly and set out the flange rings in correct position to both vertical and horizontal planes and welding in two rows accurately, painting two coats of synthetic best quality enamel paint over a coats red oxide primer including providing necessary nuts and bolts , rubber packing grease etc , all labour charges for lifting and holding of pipes as per the necessity of welder at site

OD153323/2022-2023:Charges for conveying back the 2 Nos 75 HP motor , 5 HP Vacuum motor pump sets , Oil type slipring starter with oil tank , Heavy Soft starter main panel , meter board and connected accessories etc from the temporary shed to the upper platform of pump house and then lowering down for refitting by using crane and with man labour by pushing and pulling using crobar , sleepers , rope etc and place conveniently on the shed

90.14.5:Supply and fabrication conveyance and installation of angle iron frame work for wall mounting panel board

14.7:Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.

OD153324/2022-2023:Charges for refitting the KSEB meter Board, DOL Starter, slip ring motor starter in position and 5 HP Vacuum motor pump set to the foundation.

OD153360/2022-2023:Charges for refitting the MSB /soft starter panel board, connecting the cables, testing and trial run the motor pump set at full load.

OD198353/2022-2023:Supply and fabrication conveyance of base frame of foundation of motor pump set using 75 x 40 mm rolled steel channel (ISMC) with required number of bolts and nuts

OD195737/2022-2023:Charges for providing Vacuum pipe line for Vacuum pump sets by providing 25 mm GI Pipe , GI Bend G I Coupling , Hose collar, Hose coupling , Half turn valve , Flexible hose , necessary bolts and nuts etc complete with all industrial charges and labour charges

Electrification works

1.10.1:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group A

1.33:Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.24.1:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.27.2:Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.24.3:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.5:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

90.4.5.4:Supply, Installation, testing and commissioning of ceiling fan of following sizes including wiring the down rods of standard length (up to 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. 1200mm sweep - ceiling fan complete with service value minimum 4.0(cub meter/minute/Watt), Air delivery minimum 210(cubic meter/minute), Copper winding suitable for 230V/240V single phase AC supply

90.4.1:Supply and installation of suitable size MS rod type fan clamp in the RCC slab as per IS 732 as required.

1.25:Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

90.3.20.3:Supply & installation of light fittings on TW round block <br> Supply, conveyance installation testing and commissioning the light fittings of following types made of CRCA with 0.5mm thickness complete with all accessories and lamps etc. directly on wall or ceiling with PVC round block neatly painted to suit the fitting and giving connection with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS and giving connections as required.1200 mm 1X20W LED Lamp with box type fixture

90.3.21.3:Supply & installation of light fittings on 'C/U' shaped flat iron bracket <br> Supply, conveyance, installation, testing and commissioning the light fittings of following types made from 0.5mm CRCA sheet complete with all accessories and lamps etc. directly on wall using 2 nos. 'C/U' brackets made from 20 x 3 mm MS flat, painting the flat iron bracket and giving connections with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connection etc. as required.1200 mm 1X20W LED Lamp with box type fixture

90.3.18.1:Supply, fabrication, conveyance and fixing the following sizes of B class GI pipe bent to shape / cut and welded to shape and fixing the same to wall / parapet using clamps as noted along with each size, painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer, making good the damages, colour washing etc as required.25 mm dia with HG company fabricated clamps

90.15.4.1:Supply Conveyance, installation, testing and commissioning of 20W LED street light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing,acrylic cover complete with THD Less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

OD197232/2022-2023:Supply and providing 7W LED Bulb

1.34:Supplying and fixing brass batten/ angle holder including connection etc. as required.

90.6.10.1:Supply and fixing of following sizes of light gauge PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required20 mm

90.6.10.2:Supply and fixing of following sizes of light gauge PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required25 mm

1.17.3:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

2.3.2:Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8 way, Double door

2.12.1:Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.14.2:Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.10.1:Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

5.4:Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.14:Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

5.15:Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

OD167587/2022-2023:supply and providing test joint for the earthing system using 2x25x3mm size tinned copper strips including cutting and bending to shape drilling necessary holes and fixed to the watering pipe etc as required.

1.17.12:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.11:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 2.5 sq. mm

1.17.20:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.2 x 4 sq. mm

90.12.24.1:Supply of superior quality copper tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required.2.5 sq mm

1.17.21:Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

90.12.24.2:Supply of superior quality copper tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required.4 sq mm

90.16.1.6:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required6.00 mm copper conductor (4 SWG)

90.16.1.3:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.1.2:Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.65 mm copper conductor (12 SWG)

90.16.5.2:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.65 mm (12 SWG)

90.16.5.6:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.6. mm ( 4 SWG)

90.16.5.3:Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

OD167585/2022-2023:Supply and providing the following sizes of bolt and nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required 25 x 6mm brass bolt & nut

OD167584/2022-2023:Supply and providing the following sizes of bolt and nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required 25 x 3mm brass bolt & nut

OD167583/2022-2023:Supply and providing 70 sq mm FRLS PVC insulated and sheathed single core flexible copper conductor cable

90.12.24.9:Supply of superior quality copper tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required.70 sq mm

1.21.4:Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.40 mm

OD167637/2022-2023:supply, installation testing and commissioning of Illuminated flush head Push Button with LED, for operating the75HP slip ring Motor from near side on suitable size fabricated 1.6mm CRCA sheet, powder coated

OD167640/2022-2023:Supply and filling of transformer oil of good quality to the Transformer /starter/ regulator etc as required

90.14.24.2:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.2 KVAr, 3 phase, 440 V, delta connected standard duty Metalised Poly Propylene Capacitor, Cylinderical Type, suitable for direct connection to motors.

90.14.24.11:Supply & fixing the following Power Capacitors 3 phase delta connected in positon and giving connection.20 KVAr, 3 phase, 440 V, delta connected standard duty Metalised Poly Propylene Cylinderical Type Capacitor, suitable for direct connection to motors.

OD205789/2022-2023:Supply of insulated fuse pulling handle L&T , C&S or equivalent for Type HN fuse-link from 63A-800A

OD206130/2022-2023: Supply and providing make 300 mm Heavy duty flat screw driver

OD206131/2022-2023:Supply and providing 150 mm medium duty flat screw driver

OD206132/2022-2023:Supply and providing Double ended spanner set

OD206133/2022-2023:Supply and providing Combination Plier 210 mm

OD206134/2022-2023:Supply and providing Line Tester 200 mm

OD206135/2022-2023:Supply and providing 4 Kg. Dry Chemical Powder type Fire Extinguisher with hose and clamps including fixing it to wall as required.

OD207921/2022-2023:supply and providing chain pulley block and connected accessories having 3 Ton capacity.

OD207953/2022-2023:Supply , Conveyance and fitting 200A/250, HRC Fuse Base suitable for HRC Fuse link in the existing Meter box.

OD207954/2022-2023:Supply and providing 200 A HRC FUSE ( Type 1 ) suitable for DIN type base

Bidder Name

JEFRIN PINHERO