Agri super market at VFPCK HQ in Kakkanad

Amount

DSR2.31 Clearing grass and other overgrowth of vegetation and small trees of grith upto 30cm including rooting out and removal of rubbish upto a distance of 150m outside the periphery of the area cleared.

DSR 2.8.1 Earth work excavation in ordinary soil depositing with initial lead of 50m and lift upto 1.50 m including breaking clods, watering, ramming and sectioning of spoil bank. All kinds of soil.

DSR 4.1.5Providing PCC 1:3:6, using 20mm broken stone including watering, curing etc.complete.1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size).

DSR 5.1.2RCC M20 using 20mm broken stone including all form work, watering, curing etc.complete but excluding the cost and labour for reinforcement for COLUMN FOOTING. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering

RCC M20 using 20mm broken stone including all form work, watering, curing etc.complete but excluding the cost and labour for reinforcement for COLUMN PEDASTAL.

DSR 7.1.1 Random Rubble Masonry with hard stone including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) in Cement mortar 1:6 (1 cement : 6 coarse sand) for RETAINING WALL Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR 50.6.1.1Solid block masonry using pre cast solid blocks ( factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part 1 of 1979 for foundation and plinth with thickness 20 cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

RCC M20 using 20mm broken stone including all form work, watering, curing etc.complete but excluding the cost and labour for reinforcement for TIE BEAM FOR RETAINING WALL

Centering and shuttering (RCC BELT)

DSR RCC M20 using 20mm broken stone including all form work, watering, curing etc.complete but excluding the cost and labour for reinforcement for PLINTH BEAM

Centering and shuttering

Providing and laying DPC 120 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)Including all materials but excluding cost of reinforcement

DSR 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

COLUMN - Supplying, fabrication and fixing of columns ( I Sections) as per drawings attached. (Reffer drawing No. COM_015_ARCH_201-210.) DSR 85.102 Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges ISMB 200 C2

Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges ISMB 250 C3

DSR 85.105 Supply of SS plates of grade 304L including cost of conveyance chargesSteel plate of 6 mm thickness, with 6 BOLTS for fixing I sections with column pedastal.

DSR 50.10.1 COLUMN FOR CANOPY - Supplying, fabrication and fixing of columns (Square Hollow Sections)(Reffer drawing No. COM_015_ARCH_201-210.) Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete SHS 80 X 80 x 3 mm, SHS 50X50X3 and SHS 40X40X3 mm

DSR 85.102 BEAMS - Supplying, fabrication and fixing of Beams ( I Sections) as per drawings attached. For structure. Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges ISMB 150, 250, 200 nad ISA 50X50X6 and ISA 50X50X3

DSR 26.43 LIFT WALL - Cement fibre panel . Wall panel supply & fabrication work with 5cm X 5cm X 3mm square tube sections at 1.2m horizontal & 0.8m vertival centre to centre. Using cement fibre board of thickness 10mm.Everest or Equivalent.(Reffer drawing No COM_015_ARCH_401-403.).Providing and fixing internal wall panels on Light gauge steel frame work with 10mm thick gypsum plaster board conforming IS 2095:2011 fixed on 8mm thick fiber cement board conforming to IS 14862:2000 of category III type B (High pressure steam cured) as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately)

DSR 26.43 WALL - Cement fibre panel . Wall panel supply & fabrication work with 4cm X 4cm X 3mm square tube sections at 1.2m horizontal & 0.8m vertical centre to centre. Using cement fibre board of thickness 8mm. Everest or Equivalent.(Reffer drawing No. COM_015_ARCH_401-403.) Cement fibre panel - 8mm

WALL - 6mm TOUGHENED GLASS PANEL- Supplying and fixing toughened plain glass panels of 6mm thickness properly fixed on steel frames (50mm x 50mm x 3mm) with rubber beading and all edges properly sealed with silicon sealent. As per attached drawing.(Reffer drawing No. COM_015_ARCH_401-403.)TOUGHENED GLASS - 6mm

DSR 85.107 Steel grid for Vertical garden - 6mm dia MS rod, at 15cm c/c placed in 50mmX50mmX3mm SHS MS Tube frame. Supply of MS round bar including cost of conveyance charges 6mm MS round bar

Terracota jali block work - Supplying and fixing terracota wall panels (20cmX20cmX6cm-Camp & Pearl model) between steel frame work of C section (4cmX7.5cmX3mm) at intervels of 5-7 blocks.terracota wall panels (20cmX20cmX6cm-Camp & Pearl model)

DSR 26.45 FLOORING- Cement floor panel. Supplying and fixing of 15mm thick, 8'X4' panel, Everest Fibre Cement flooring board ( High density) or equivalent as 60cm X60cm tiles with 6 mm thick filling and support Chanel (50mm X 50mm X 3mm square tube sections). Everest Fibre Cement flooring board -6 mm thick

DSR 26.45 STAIR- with " C " sections as support beams and aluminium chequred sheets and MS gratings attached as tread. MS gratings are attached to support beams with 8 mm thick MS plate. (width = 1.50 m, Rise = 0.15 m and Tread = 0.30 m)(Reffer drawing No. COM_015_ARCH_404.)Cement Fibre board

DSR 10.28 Supplying and fixing SS (304 Grade) Hand Rails including cost of meterial,labour charge etc…complete.(Reffer drawing No. COM_015_ARCH_404.)Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Roofing with PUF Sandwitched Aluminium coloured sheets : 30 mm PUF coloured sheets, SHS 60x60x4 (Purlins) mm at 60/120 c/c. as per drawing.(Roof Truss Details)(Reffer drawing No. COM_015_ARCH_201-210.)PUF coloured sheets

EAVE BOARD Supplying and fixing of Multiwood eco board of 12 mm thickness (Thomson or equivalent.) of 15 cm height with necessary fittings.

Supplying and fixing of PVC Rain water gutter with necessary clamps and fittings (20 cm wide square type)

ROOF FOR CANOPY - Providing and fixing 12 mm thick toughened glass of approved brand and manufacture with necessary fittings and sealants.

DSR 12.26.1False Ceiling for café space( Solid panels) . Supply and fabrication works of false ceiling with cement fibre board of thickness 6 mm (Everest or equivalent) fixed on Squre Tube Sections, 50x50x 3mm, 6MM THICK CEMENT BOARD AS PER 14862

DSR 5.22.6 Reinforcement for RCC works,bent,tied and placed in position as per structural design.

DSR 13.7.2 Plastering with cement motar1:4, 12 mm thick one coat including cost of materials, labour, conveyance etc. complete (PLINTH)

DSR 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately).

Supplying and fixing of Door handle, lock and stopper.

Providing and fixing frames of aluminium door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineer-in-charge excluding cost of glass.

DSR 21.3.3 Providing and fixing glazing in aluminium door etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness

Supplying and fixing of Door handle, lock and stopper.

Service door - 40mm x 40mm x 3mm Aluminium frame with 12mm cement fibre board of size.( 0.90m x 2.00m )

( 1.00m x 1.00m ) Duct door

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing.

Aluminium sliding windows Supplying, fabricating and fixing anodised/powder coated aluminium sliding windows of size as per drawings using Aluminium extruded Architectural sections from standard manufacturers with 4 mm glass panels fixed using good quality beedings, hinges, handles etc. complete.(Reffer drawing No. COM_015_ARCH_601-602.)

Aluminium awning windows Supplying, fabricating and fixing anodised/powder coated aluminium awning windows of size as per drawings using Aluminium extruded Architectural sections from standard manufacturers with 3 mm glass panels fixed using good quality beedings, hinges, handles etc. complete.(Reffer drawing No. COM_015_ARCH_601-602.)

DSR 10.6.1 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 -part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25mm M.S. laths with 1.25 mm thick top cover.

DSR 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. (AT -1.50 LVL & +0.45 LVL)

DSR 11.38 TOILET FLOORING - Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

DSR 11.36 TOILET WALLS - Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

DSR 13.60.1 Wall painting with acrylic emulsion paint - INTERIOR - of approved brand and manufacture to give an even shade: Two or more coats on new work.

DSR 13.46.1 Wall painting with acrylic emulsion paint - EXTERIOR - of approved brand and manufacture to give an even shade: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

DSR 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: (MAT BLACK) - UNDER SIDE OF FLOOR PANELTwo or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

DSR 13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete . On steel work

Supplying and fixing of freight lift of size 1.50 m x 1.50m X 2.00 m with 3 stops, including motar and necessary fittings.(Hoist Tech Engineering works, Njarakkal)

Supplying and fixing of Wind Driven turbo Ventilator with a speed of 350 rpm, brand - Air roof Ventilators or equivalent ( Aluminium or steel , 60 cm DIA.) with necessary fittings.

METERING PANELSupply, erection, testing and commissioning of cubicle type, dust and vermine proof wall mounted panel board made out of 16 SWG thick CRCA sheet duly rust inhibited degreeasing zinc phosphating and painted with epoxy paint of approved colour and quality, over a coat of zinc-chromatic primer, complete with hinged and earthed front doors, with locking and sealing provision, heavy duty rubber gaskets,remov able gland plate made of 3mm thick sheet steel, all connections and inter connections including mounting the following(testing , sanctioning and certification of Energy meter from Electrical Inspectoate and KSEB shall be obtained by the contractor)Provision for mounting of L&T make 3 phase 4 wire CT operated electronic energy meter 3 Phase 4 wire CT operated Electronic Energy Meter 100A cutout with HRC fuse unit 100A Neutral Link - 1No 100A TPN SFU - 1 No

VERTICAL DISTRIBUTION BOARD (AC DB)Supply and installation of 4way VTPN MCB DB,dust and vermin proof enclosure of vertical type with IP-43 with metal double door , including busbar ,neutral link and DIN bar suitable for fixing MCCB/MCB/MPCB isolators,necessary dummy covers etc.in recess including cutting holes on the wall making good the damage colour washing etc. as required . 63A FP MCB-1 no 32A SP MCB- 11 nos Spare- 2 nos

HORIZONTAL DISTRIBUTION BOARDS Supply and installation of 6 way TPN MCB DB, with IP-43 metal double door for three phase inclusive of bus bar, neutral link and DIN bar suitable for incorporating MCB,RCBO ,isolator, cable entry etc,in recess including cutting holes on wall,making good the damages colour washing etc as required and to install the required incomer and outgoing breakers

Supply and installation of 12 way SPN MCB DB, with IP-43 metal double door for Single phase inclusive of bus bar, neutral link and DIN bar suitable for incorporating MCB,RCBO ,isolator, cable entry etc,in recess including cutting holes on wall,making good the damages colour washing etc as required and to install the required incomer and outgoing breakers

RCBO Supply and installation of following rating RCBO of approved make in the existing enclosure and giving interconnection(Supply & labour)63A FP RCBO 100m A

40A FP RCBO 30m A

32A DP RCBO 30m A

Supply and installation of following rating MCB of approved make in the existing enclosure and giving interconnection(Supply & labour)32/20/16/10/6 A SP MCB

Isolators Supply and installling the following rating isolator on a suitable modular enclosure giving connections including cutting the brick wall, fixing , making good the damages etc63A FP Isolator

40A FP Isolator

32A FP Isolator

32A DP Isolator

EARTHING Plate Earthing Supply and installation of 600mmx600mmx6 mm CI. plate electrode earth station conforming to IS:3043-1987 / NEC / IEE complete with brick masonry chamber, CI cover, CI frame ,GI watering pipe of 25 mm dia with funnel having 20G GI wire mesh etc, The CI cover frame/ chamber shall be of 25 cms x 25 cms . CI manhole cover with frame shall be painted with bitumastic paint, identification of earthpit with yellow paint below the chamber cover, mixtures of charcoal & common salt around electrode including digging of pit up to permanent moisture level but not less than 3 metre depth and back filling. ( value of earth resistance should be less than 2 ohm )(For UPS)

Pipe Earthing Supply and providing efficient pipe earthing using 3.6m long 6mm dia class B GI pipe earth electrode , water pipe, earthing strip, terminal electrode , etc. and the pit filled with alternate layers of charcoal and salt etc. and construction of inspection chamber with a bed concrete of 1:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar 1:6, plastering the surface of brick masonry and the exposed surface of PCC bed with cement mortar 1:4, 12 mm thick, (the finished inside dimension shall be 300 x 300 x 300 mm)is covered with heavy duty CI hinged chamber cover . The earthing station should confirm to IS 3043/87. From this Earth Bus 8 SWG copper Earth conductor shall be drawn to VDB/ Meterring panel and 10 SWG copper shall be drawn to Horizontal DBs.

EARTHING CONDUCTORS Supply, laying / fixing of earthing conductor of GI / CU flat / wires jointing as per IS:3043 / 87 in trench walls pulling through pipes etc as required.All earthing connections using SWG Copper conductors are to be crimped with proper copper lugs and shall be connected to the respective earth locations of DB'S etc as per specifications25 x3 mm Cu strips

Copper wire No.8 SWG

Copper wire No.10 SWG

Earth Bus supplying ,clamping and connecting 25x3 mm Cu as earth bus.

Supply of superior quality copper earth socket for No 10SWG copper conductor including crimping

Supply of superior quality copper earth socket for No 8SWG copper conductor including crimping

CABLE TRAY Wire mesh Cable tray shall be designed and tested as per IEC 61537.The Mesh cable tray shall be of Hot Dip Galvanised confirming to DIN E 12329 should be interlocked for connecting the consecutive tray with additional connectors. The Diameter of the steel wire shall be minimum 4.8 mm The Wire mesh cable tray shall be supplied with the standard length of 3 Mtr. All the wires in the Mesh cable tray shall be with the same thickness. The weight bearing capacity for a span of 1 meter shall be 60 kg complete with accessories including support from walls, and cover for cable tray .400 mm width x 50mm Height

Supports for cable tray from wall

Cover for cable tray

CABLE LAYING & END TERMINATION Supplying and laying the following X.L.P.E insulated 1.1 kV grade aluminium conductor cable conforming IS:1554 ( Part-I ) in cable trenches or on concrete wall or through pipes as per specifications. Necessary clamping should be provided while burying cables in prepared trenches etc. as instructed by the Consultant 3.5 Cx 50 sq. mm Armoured Al Cable3.5C x 25 sq. mm AL Cable

4C x 16 sq. mm AL Cable

4C x 16 sq. mm Cu Cable 4C x 10 sq. mm AL Cable

2C x 10sq. mm Al Cable

4C x 6sq. mm Al Cable

2C x 6sq. mm Al Cable

4C x 6sq. mm Cu Cable

2C x 6sq. mm Cu Cable

Supplying Siemens type / tropodor type compression gland for. XLPE /PVC insulated and PVC sheathed armoured Aluminium / Copper conductor cable 1.1kV grade and making end termination using alluminium lugs, earth clamp etc complete for suitable cables of the following sizes as required. 3.5C x50 sq. mm Al Cable

3.5C x 25 sq. mm AL Cable

4C x 16 sq. mm AL Cable

4C x 16 sq. mm Cu Cable

4C x 10 sq. mm AL Cable

4C x 10sq. mm Cu Cable

2C x 10sq. mm Al Cable

4C x 6sq. mm Al Cable

2C x 6sq. mm Al Cable

4C x 6sq. mm Cu Cable

2C x 6sq. mm Cu Cable

Supply and wiring of the following wires through existing suitable size ISI grade PVC round conduits/ floor ducts2 runs 1.5 sqmm Cu wire(For point wiring additional length exceeding 5m)

2 runs 2.5 sqmm Cu wire + 1 run 2.5 sqmm green Cu wire (Circuit mains , 6A multi sockets looping , power point wiring, Master switch control lighting points )

2 runs 4 sqmm Cu wire + 1 run 4 sqmm green Cu wire (A/C point wiring)

Conduits Supplying and laying of ISI grade rigid PVC conduits concealed in wall/slab etc complete with necessary accessories for DB incomer wiring /telephone/music system wiring. The rate includes chasing of wall/slab and plastering the chased portion as required. 32mm dia

25mm dia

20mm dia

Supplying all materials and wiring for light and exhaust fan points using 1.5 sq.mm 1100V grade PVC insulated copper conductor single core stranded wires of IS 694 specification and should have IS marking, through ISI medium grade 20mm rigid PVC conduits concealed in wall / slab etc,complete with necessary accessories, including supplying and fixing 6A modular type switch housed in a suitable factory made M. S box with moulded front plate including earthing the box, complete as required.(The rate include removing debris, packing and rough plastering the grews after conduiting)Single control light Point / Exhaust fan point

Two way control points (one light controlled by two switches)

Two lights controlled by one switch

Three lights controlled by one switch

Four lights controlled by one switch

Five lights controlled by one switch

Six lights controlled by one switch

Supplying all materials and wiring for ceiling fan points with 100 W electronic regulator using 1.5sq.mm PVC insulated copper conductor single core stranded wires of 1100V grade and1 run of 1.5 sq.mm green copper wire for earthing continuously run as per IS through ISI medium grade rigid PVC conduits concealed in wall/slab etc., complete with necessary accessories, including supplying and fixing 6A modular type switch and 100W electronic fan regulator housed in a suitable factory made M. S. box with moulded front plate including earthing the box,complete as required.(The rate include removing debris, packing and rough plastering the grews after conduiting)(Length upto 5M)

Wall fan point

Supplying all materials and wiring for 6A plug points in independent positions using 2 runs of 1.5 sq.mm PVC insulated copper conductor single core stranded wire, earthing with 1 run of 1.5 sq.mm green copper wire inside the conduit/flat conduit , and fixing 6A modular type plug socket (2 in 1) controlled by 6A switch with moulded front plate, housed in a suitable factory built MS box. Giving connections, earthing etc complete as required.

Supplying all materials and wiring for 6A plug points in combined positions using 1.5 sq.mm PVC insulated copper conductor single core stranded wire, earthing with earthing with 1 run of 1.5 sq.mm green copper wire inside the conduit/flat conduit , and fixing 6A modular type plug socket (2 in 1) controlled by 6A switch with moulded front plate, housed in a suitable factory built MS box. Giving connections, earthing etc complete as required.

Supplying all materials and fixing modular type 16A power plug point with 16A 3 pin modular type plug socket controlled with 16A switch with moulded front plate, housed in a suitable factory built MS/PVC box. as per IS, giving inter connection etc complete as required (Wire, conduit not included).

Supplying all materials and fixing modular type 20 A power plug point with 20A 3 pin socket controlled with 20 A SP modular switch with moulded front plate, housed in a suitable factory built MS box. as per IS giving inter connection etc complete as required.(1 Ton AC point) the switch shall be fixed at a height of 120 cm from finished floor level (Wire, conduit not included)

Supplying all materials and fixing modular type 25 A power plug point with 25A 3 pin socket controlled with 25 A SP modular switch with moulded front plate, housed in a suitable factory built MS box. as per IS giving inter connection etc complete as required.(1.5 Ton AC point) the switch shall be fixed at a height of 120 cm from finished floor level (Wire, conduit not included)

Supplying all materials and fixing modular type 32 A power plug point with 32A 3 pin socket controlled with 32 A SP modular switch with moulded front plate, housed in a suitable factory built MS box. as per IS giving inter connection etc complete as required.(2 Ton AC point) the switch shall be fixed at a height of 120 cm from finished floor level(Wire, conduit not included)

supply and installling 450mm sweep industrial exhaust fan including fixing , making good the damages etc as approved by the consultant

supply and installling 1200 mm sweep ceiling fan with double ball bearing including all accessories etc as approved by the consultant

Installation ,testing and commisioning of wall mounted LED wall light pre-wired, complete with all accessories

Installation , testing and commissioning of wall mounted flood light, pre-wired and complete with all accessories

Installation , testing and commissioning of spot lights on track, complete with all accessories

Installation , testing and commissioning of Round down lights complete with all accessories

Installation , testing and commissioning of round down spot lights complete with all accessories

Installation ,testing and commisioning of Air curtain complete with all accessories

Preparation of as built drawings & obtaining power connection from KSEB for commissioning of the whole installation in the premises. All statutory payments will be reimbursed on production of the original receipts.

European type white glazed earthern ware W.C pan with P trap (Indian make - best quality) and duro plastic seat and lid with C.P brass hinges and rubber buffers ,PVC low level flush tank of 5 litres capacity (Indian make - best quality) with 15 mm float valve fitting and C.I brackets, 32mm dia PVC telescopic flush pipe 165 cm long with fittings and clamps, over flow pipe with mosquito proof arrangement, 15mm PVC connection 1no,15mm CP angle valve 1no, etc. complete including cutting and making good the walls and floor.

Ovel Counter Top wash basin installed below granite/ marble with CI / MS brackets, 15mm dia CP pillar cock fitting, 32mm dia CP waste coupling with plug and chain,32mm dia CP brass bottle trap, PVC / CP hot & cold watersupply connecting pipe, two nos of 15mm dia CP angle stop cock for hot & cold watersupply liness with wall flange etc., The works shall include cutting in walls and making good the walls & floors. Size of wash basin 55 x 40cm

Stainless Steel Soap dish 150 x 150mm including cutting and setting in walls with cement joints and making good the wall.

15mm dia CP Long Body Bib Cock with CP wall flange etc.

CP Health Faucet consisting of:

CP angle stop cock with wall flange.

PVC flexible tube.

C.P. Brass Pillar tap (Wash Basin)

Concealed stop cock with adjustable wall flange complete including cutting and making good the wall etc. complete

Gratings( toilet) including white cement pointing.(in Toilets)

Shower rose CP (with Stop Cock)

PVC pipe 3Kg/cm2 and 4 Kg/cm2 and joining specials such as tees, bends, elbows, checknuts, etc. with clamps including cutting and making good the walls, painting with suitable paint 2 coats complete. 6Kg/cm2 I NTERNAL (CONCEALED IN WALL)32 mm dia

40 mm dia

50 mm dia

63 mm dia

75 mm dia

110mm dia

8Kg/cm2 25 mm dia

Ball valves of brass body nickel plated with stainless steel ball, lever operated (RB make) and tested to 20kg / sq.cm.32 mm dia

50 mm dia

100 mm dia

Plastic ball float valve with gun metal lever of approved quality for muncipal water inlet pipe to UG sump.

Water meter confirming to IS 2372 - 1981, kranthi / dasmesh make with direct reading dia in KL with all integral parts of gun metal or brass with neccesary fittings such as threaded pieces, unions, check nuts complete.

Providing and fixing of PVC encapsulated foot steps 300 mm staggered apart for UG sump tank as per standard make of SFRC or equivalent make fixing in RCC walls during casting of RCC walls as per location shown in drawings.

Pump sets for Drinking Water - 1 HP, with 20 mts head and 1.5lps discharge

Pumping Main 50 mm PVC 8kg/cm2

Excavating trenches of required width and depth for water supply pipes, etc., in all kind of soils including excavation for sockets and dressing of sides, ramming of bottoms & getting out the excavated soil & then refilling the tranch with soil as tranch with soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc., including disposal of extra soil to a lead of min 50mtr or on instructed by the site Engineer.

PVC soil, waste and vent pipe confirming to IS 13592 of SWR quality 4 kg / sq.cmand 6Kg/sqcm pressure rated including all fittings, like Bends, Tees, Elbows, Collars, junction, inspection doors, cowls, offsets, access pipes, jointing with rubber ring / solvent cement followed by application of leak proof adhesive like FRP paste, including cutting masonry or concrete floors, sunshade etc, wherever necessary for taking connections, fixing the pipe to walls with iron clamps and screws to T.W plugs embedded in cement mortar including spare sockets, scaffolding wherever necessary, painting the exposed faces with suitable paint 2 coats etc. complete. 40mm dia (6kg / sq.cm

63mm dia (6kg / sq.cm)

75mm dia (4kg / sq.cm)

90mm dia (4kg / sq.cm)

110mm dia (4kg / sq.cm)

140mm dia (4kg / sq.cm)

100 mm Gully trap for the waste lines with brick jelly concrete in Lime mortar, necessary brick masonry around plastering with cement mortar 1:3,12 mm thick with neat cement flushing coat etc., complete including providing two nos. Heavy C.I gratings 150 x 150mm and 225 x 225mm for the inside and outside painted with black Japan two coats and necessary earth work excavation etc. complete.100mm x 100mm size `P/S' trap

Sewer Manhole of size 60cm x 60cm inside and depth not exceeding 120 cm with 20 cm( one brick) thick walls in cement mortar 1:6 plastering inside with cement mortar 1:3, 12 mm thick with neat flushing coat and foundation concrete 20 cm thick and forming channels with cement concrete 1:3:6 using 40 mm broken stones, providing collars around pipes with cement concrete 1:2:4 using 20 mm broken stones , corbels at top courses on two sides and RCC slab 100 cm X 35 cm X 7.5 cm on other side with cement concrete 1:1.5:3 using 20 mm broken stones and necessary reinforcement and providing necessary CI step and CI manhole cover (Heavy).

Excavating trenches of required width and depth for drainage pipes, etc., in all kind of soils including excavation for sockets and dressing of sides, ramming of bottoms & getting out the excavated soil & then refilling the trench with soil as tranch with soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc., including disposal of extra soil to a lead of min 50mtr or on instructed by the site Engineer.

Constructing masonry shoe to the bottom of rain water pipes with brick in CM 1:6 over 10 cm thick PCC 1:4:8 using 40 mm nominal stones, plastering the exposed surface using CM 1:5 one coat, forming circular spout etcSize- 0.2m x0.2m x0.3 m

Rain Water Collection Pipe 75 mm Class 3

Rain Water Leading Pipe to Sump - 90 mm Class 3

Pump sets for Rain Water - 1 HP, with 20 mts head and 1.5lps discharge

Rain water Pumping Main 75 mm PVC

Excavating trenches of required width and depth for rain water pipes, etc., in all kind of soils including excavation for sockets and dressing of sides, ramming of bottoms & getting out the excavated soil & then refilling the tranch with soil as tranch with soil as required in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc., including disposal of extra soil to a lead of min 50mtr or on instructed by the site Engineer.

CUBE INDIA ENGINEERING

MATRIX BUILDERS AND DEVELOPERS

Roofco Builders and Developers