GE AF/AMB-51/2020-21 PROVISION OF OPEN SHED OVER MAIN GATE AND TWO WHEELER PARKING SHED NEAR MAIN GATE AT SITE-II (RAJPURA) UNDER GE (AF) AMBALA

Amount

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundations, manholes, etc. or for laying cables/pipes, erecting poles, etc.not exceeding 10sqm on plan and getting out in soft / loose soil complete all as specified and as directed

Returning, filling in, including, spreading, leveling, watering and well ramming in layers not exceeding 25cm deep as in any type of soil complete all as specified and as directed

Removing excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point in any type of soil including spreading in low lying area and leveling complete all as specified and as directed

Formwork to plinth beams, foundation footings, etc. and similar works for rough finish surface complete all as specified and as directed

Formwork to sides of pillar, columns, etc. in flat surfaces for rough finish complete all as specified and as directed

M&L for plain cement concrete in 1:4:8 (type D-2) using 40mm graded stone aggregates as in foundation, filling, mass concrete, etc. complete all as specified and as directed

M&L for RCC M-25 (nominal mix) as in plinth beams, bands, lintels, etc. complete all as specified and as directed Note: Formwork and reinforcement will be measured and paid separatey under respective item herein

M&L for RCC M-25 (nominal mix) as in columns, footings, etc. and similar works complete all as specified and as directed Note: Formwork and reinforcement will be measured and paid separatey under respective item herein

M&L for mild steel TMT bars grade Fe-500D, 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M&L for mild steel TMT bars grade Fe-500D, 6mm dia upto and including 10mm, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M&L for mild steel joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-290 (grade E-165) complete all as specified and as directed

S&F mild steel work in tubular trusses including special shaped washers, etc. using ERW or induction butt welded tubes conforming to IS-1161-1979 structural grade 240 complete all as specified and as directed

S&F in location mild steel sheet 1.25mm thick eaves gutters 150mm dia, galvanised class 3, half round with rounded edges with and including necessary clamps as required complete all as specified and as directed

M&L rendering 15mm thick in cement mortar (1:4) on fair surfaces of PCC block / brick masonry wall / concrete surfaces, etc. finished even and smooth without using extra cement complete all as specified and as directed

M&L for preparing of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint (tint as approved) over a coat of red oxide zinc chrome primer complete all as specified and as directed

M&L for preparing of new plastered or unplastered surfaces and applying two coats of cement based paint (of approved tint) over a coat of chalk whitening on walls complete all as specified and as directed

M&L preparation of new plastered / unplastered and applying three coats of white wash on walls, etc. complete all as specified and as directed

S&F in position aluminium-zinc colour coated high tensile alloy steel trap sheeting of 0.5 to 0.53mm thick, high rib, having 550 Mpa yeild strength BMT 0.45mm and zinc (galvanized) and aluminum combined coating of 150 gms/sqm (AZ-150) of 0.50mm TCT having top colour coat of regular modified polyester/silicon modified polyester/HDPE polyester of 18 to 20micron and back coat of 5 to7 micron epoxy primer fixes, RMR 1040 profile width 1125mm in roofing panels / sheeting complete as per manufacturer's instructions, all as specified and as directed Note: The sheet shall be fixed to MS angles with self drilling and self topping screws conforming to AS 3566 with moulded EPDM washers

M&L for fine dry river sand cushioning by laying 8cm thick layer below the cable for making soft bed and 15cm above the cable and then punning down to its consolidated thickness of 18cm after the cable is laid all as specified in SSR Part-I complete all as specified and as directed Note: Only punned thickness of sand shall be considered for measurement purposes

Supply and laying burnt bricks of sub-class 'B' designation 75 laid in trenches for cable protection complete all as specified and as directed

Supplying, fixing to walls, poles, etc. / laying in trenches 1100V grade, heavy duty cable, PVC insulated solid aluminium conductor of c/s area 6sqmm, served with inner sheathing of PVC tape and overall PVC sheathed complete all as specified and as directed

S&F isolator SPN 240V 5 to 40A, 10kA complete all as specified and as directed

S&F isolator SP 240V 6 to 32A, 10kA complete all as specified and as directed

S&F sheet metal enclosures for MCB distribution board 240V SPN 8 way double door, flushed inside walls, etc. with 100Amps rated busbar with and including necessary thimbles, plugs, nuts, bolts, etc. and making good the disturbed surfaces complete all as specified and as directed

M&L for point wiring with 1.5sqmm, single core, FRLS PVC insulated, ISI marked, unsheathed cable 1100V grade with multi-stranded copper conductor, drawn through and including non-metallic rigid PVC casing capping not less than 20mm wide and accessories surface on walls, ceiling etc., and including provision of 1.5sqmm copper wire, green colour as earth continuity conductor and connected to common earth dolly with MS sheet (1.6mm thick) sunken box or pressed steel terminal boxes with provision of 3mm thick plastic laminated sheet top cover complete all as specified and as directed for the following:

One light / ceiling fan / exhaust fan point controlled by one 5A one way switch

One switch socket outlet 3 pin 5Amps on independent board

One switch socket outlet 3 pin 5Amps on same board

S&F switch piano flush button type, single pole, ISI marked, one way 5A, 240V complete all as specified and as directed

S&F ceiling rose surface bakelite 65x50mm, ISI marked, with three terminals complete all as specified and as directed

S&F highly efficient LED bay light 100W made out of die cast aluminium housing with 10kV SPD lens with toughened glass enclosure of IP-66 protection class, all accessories pre-wired and connecting up complete all as specified and as directed

S&F air circulators, heavy duty, PVC body with PVC blades, ISI marked energy efficient, 230V, BEE five star rated, 450mm sweep with lauvers and connecting up including provision of three core flexible copper wire of size 1.5sqmm from ceiling rose to circulator including grouting the nuts and bolts complete all as specified and as directed

S&F pedestal fans, heavy duty, PVC body with PVC blades, ISI marked energy efficient, 230V, BEE five star rated, 400mm sweep with lauvers and connecting up including provision of three core flexible copper wire of size 1.5sqmm and connecting up complete all as specified and as directed

M&L for earthing with galvanized steel earth plate electrode 600x600x6mm buried directly in ground to a depth not less than 2.25m below ground level and top edge of plate not less than 1.5m below ground level, connected to galvanized earth wire 4mm by means of GI bolts, nuts, check nut, washers, etc. including earth pit in any type of soil, filling of charcoal, common salt, black cotton soil in pit, 15cm all around earth plate, pit built in PCC 1:2:4 type B1 with 40x40x6mm angle iron frame and PCC 1:2:4 type B1 cover, water pipe, funnel, GI wire mesh and GI protection pipe light grade 15mm dia 7.5m in length, connecting to earth lead or DB/ LT panel, etc. all as shown on electric plate No. 3 of SSR complete all as specified and as directed

Notes for serial item No. 34: (i) The cost of GI earth continuity wire with GI pipe 50mm medium grade upto 7.5m is deemed to be included (ii) The earth chamber to be constructed 0.5m from edge of earth pit with necessary watering arrangement. The cost for the same is deemed to be included in above item (iii) Earthing shall produce desired earth resistance values as directed by the Engineer-in-charge

Swami Engineers

M/s Kang Builders

Swami Enterprises

Karishan Kumar goel