Providing BT Roads, Drains , painting to medians and developmental of park at DA Road at Padmavathi nagar Layout in Surappakasam.

Providing, Laying, Spreading and compacting graded HBG crushed stone aggregate to Wet Mix macadem specification ( 5th Revision) as per Table 400-13, including cost of all materials and including premixing the material with water at OMC in Mechanical mix plant carriage of mixed material by tipper to site , laying in uniform layers with paver in base courses on well prepared surface and compacting with Vibratory roller to acheive the desired density etc., as directed by the Engineer-in-Charge and as per MoRT&H specification.406 (5th revision) for finished item of work.

Providing and applying prime coat with bitumen emulsion (SS1) Bulk using emulsion pressure distributor on prepared surface of granular base including clearing of road surface and spraying emulsion at the rate of 0.70 kg/sqm using emulsion pressure distributor for finished item of work etc., complete as per MoRT&H Specification 502 (5th revision) and as directed by the Engineer-in-charge

Providing and applying tack coat with bitumen VG-10 (Bulk) using Bitumen pressure distributor at the rate of 0.25 kgs per sqm on the prepared Granular surface treated with primer cleaned with mechanical broom for finished item of work as per MoRT&H Specification 503 (5th revision) and as directed by the Engineer-in-Charge.

Providing and laying of 50mm thick Bituminous Macadam with 100 -120 TPH hot mix plant producing an average output of 75 tonnes per hour using hard blasted granite crushed aggregates of Grading - II as per table 500-7 of MoRT&H specificaion 504 (5th Revision) premixed with bituminous binder of VG-30 grade @ 3.4 % by weight of total mixture, transported to site, laid over a previously prepared surface with Hydrostatic paver finisher with sensor control to the required grade, level and alignment and rolled as per Clauses 501.6 and 501.7 to achieve the desired compaction for finished item of work as directed by the Engineer-in-Charge including hire and opeational charges all T&P and all other contingent charges necessary , complete and as per MoRTH specification No. 504 (5th Revision).

Providing and applying tack coat with bitumen VG-10 (Bulk) using Bitumen pressure distributor at the rate of 0.20 kgs per sqm on the prepared bituminous surface cleaned with mechanical broom for finished item of work as per MoRT&H Specification 503 (5th revision) and as directed by the Engineer-in-Charge.

Providing and laying of 30 mm thick Bituminous Concrete with 100 - 120 TPH batch type hot mix plant producing an average output of 75 tones per hour using hard blasted granite crushed aggregates of Grading – II as per Table 500-17 of specification 507 of MoRT&H (5th revision), premixed with Bituminous binder of VG 30 Grade @ 5.4 % of mix and filler, transporting the hot mix to work site, laying with hydrostatic sensor paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRT&H Specification 507 (5th revision) complete for finished item of work in all respects as directed by Engineer-in-Charge

Supply and placing of M25 Design Mix using 10mm HBG crushed metal 0.480 cu.m, 6mm HBG crushed metal 0.320 cu.m, sand 0.400 cu.m and cement 350 kg with water cement ratio of 0.53 (185.50 litres/cu.m of CC) etc., from any source conforming to the relevant ISI standards, including cost and conveyance of all materials such as cement, fine aggregate (sand), coarse aggregate, water, etc., to site and including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing, including cost of necessary form work, centering charges, shuttering charges, etc., complete with minimum cement content as per IS Code from standard suppliers approved by the department, but excluding cost of steel and its fabrication charges, for finished item of work as directed by the department (APSS No. 402 & 403) for 150 mm thick precast slabs.

Providing HYSD bars ( Fe-500 ) of different diameters, wrought and put up bars of all diameters including cost and conveyance of steel to site and all labour charges for fabrication of reinforcement including cutting, bending, binding rods, tying grills, placing them in position etc., complete including cost and conveyance of binding wire and all handling charges and operational charges etc., and including over lapping welding if required etc., complete for all R.C.C items for finished item of work as per standard drawings, as per the directions of the Engineer-in-Charge and as per MoRT&H specification 1600 & 2100 (5th revision) and as per I.S.1786 of 1985 for foundations of R.C.C items.

Flooring with Supplying precast terrazzo chequered tiles conforming to IS: 13801 using marble aggregates of size 10 mm , sand, marble powder, white cement pigments etc., with terrazzo topping not less than 6 mm of tiles overall size not less than 20 mm thick of any coloured shades. set over base coat of cement mortar (1:6) 12 mm thick over CC bed already laid or RCC roof slab, including near cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed with neat cement to full depth mixed with pigment of matching shade including cost of all materials like cement, sand water and tiles etc., complete, including seigniorage charges, complete for finished item of work.

Earthwork excavation in soils upto SDR by mechanical means for foundations of structures as per drawing and technical specification including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing sides of bottom, back filling the excavation earth to the extent required etc., complete for finished item of work, excluding seigniorage charges, as per MoRT&H specification 304 (5th Revision) and as directed by the Engineer-in-Charge

Sand filling in foundation including cost and conveyence of all materials to site and watering, tamping etc., complete for finshed item of work as per MoRT&H specification 304 (5th Revision) and as directed by the Engineer - in - Charge.

Providing Vibrated Cement Concrete (1:4:8) mix using 40mm size HBG crushed stone aggregate and fine aggregate conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, Vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2100 (5th Revision) and as directed by the Engineer-in-Charge for base coarse below

Providing Vibrated Cement Concrete (1:2:4) using 20mm size HBG crushed stone aggregate and fine aggregate conforming to table 1000-2 of MoRT&H including cost, conveyance of all materials to site and labour charges, centering, machine mixing, laying, vibrating, curing etc., including all other incidental and operational charges of all T&P etc., complete for finished item of work as per MoRT&H specification 1500,1700, 2200 (5th Revision) and as directed by the Engineer-in-Charge for Drain walls.

Vibrated cement concrete M 15 Grade Concrete using 20mm and 10mm size HBG crushed stone aggregate (Coarse aggregate conforming to table 1000-1 and fine aggregate conforming to table 1000-2) including cost and conveyance of all materials to site and all labour charges for machine mixing,laying in position, Compacting , Vibrating and curing including all other incidental and all other operational charges of T&P required etc., complete as per MoRT&H Specification 1500,1700, 2100 (5th Revision) vent portion

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T&P etc., complete for finished item of work.

Carting of unserviceable soils loading and disposal upto 1000 mts etc., complete for finished item of work as directed by the Engineer-in-Charge

Forming embankment with borrowed useful earth from outside road boundary by mechanical means upto SDR with all leads and lifts including pre-watering of soil at borrow area, removal of top soil, excavation of soils at borrowed area, conveyance of soil, depositing the soil on the embankment, spreading soil, breaking clods, sectioning, grading and consolidation with 8 to 10 Tonnes Vibratory Road Roller @ OMC to meet requirement of table 300-2 of MoRT&H, including all hire and operational charges of T&P , complete for finished item of work as per MoRT&H specification 305 (5th revision) (Payment will be made based on level for finished item of work).

Earth Work Excavation for Ordinary Soil-Manual Means with initial lift of 3 mts for foundations and depositing on bank for all lifts and with an initial lead of 50mts including all operational, incidental, labour charges such as shoring, sheeting, planking, strutting, etc., complete for finished item of work excluding dewatering chargese etc., as per SS 20B (APSS 308) as directed by the departmental officer during execution

Filling with sand (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work.

Plain Cement Concrete (1:4:8) using 40mm HBG metal with concrete mixture for foundations etc., laid in layers of not more than 15 cms thick well compacted including cost and conveyance of all materials, labour charges and curing etc., complete

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kgs),. 10 mm HBG crushed metal, 0.362 cu.m (471 kgs) , sand 0.407 cu.m (616 kgs.) and cement 380 kgs with water cement ratio of 0.48 (182.40 ltrs/ cu.m of CC)etc., to site and including all materials, operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department including hire charges for centering, shuttering, scaffolding for unsupported height up to 3.66 m using Steel pipes, jack props, wallers, Foot plates, brackets, steel Centering plates, etc., complete and excluding cost of steel and its fabrication charges for finished item of work. FOR FOOTINGS

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kgs),. 10 mm HBG crushed metal, 0.362 cu.m (471 kgs) , sand 0.407 cu.m (616 kgs.) and cement 380 kgs with water cement ratio of 0.48 (182.40 ltrs/ cu.m of CC)etc., to site and including all materials, operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department including hire charges for centering, shuttering, scaffolding for unsupported height up to 3.66 m using Steel pipes, jack props, wallers, Foot plates, brackets, steel Centering plates, etc., complete and excluding cost of steel and its fabrication charges for finished item of work. FOR PEDETALS

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kgs),. 10 mm HBG crushed metal, 0.362 cu.m (471 kgs) , sand 0.407 cu.m (616 kgs.) and cement 380 kgs with water cement ratio of 0.48 (182.40 ltrs/ cu.m of CC)etc., to site and including all materials, operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department including hire charges for centering, shuttering, scaffolding for unsupported height up to 3.66 m using Steel pipes, jack props, wallers, Foot plates, brackets, steel Centering plates, etc., complete and excluding cost of steel and its fabrication charges for finished item of work. FOR PLINTH BEAM

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kgs),. 10 mm HBG crushed metal, 0.362 cu.m (471 kgs) , sand 0.407 cu.m (616 kgs.) and cement 380 kgs with water cement ratio of 0.48 (182.40 ltrs/ cu.m of CC)etc., to site and including all materials, operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department including hire charges for centering, shuttering, scaffolding for unsupported height up to 3.66 m using Steel pipes, jack props, wallers, Foot plates, brackets, steel Centering plates, etc., complete and excluding cost of steel and its fabrication charges for finished item of work. FOR COLUMNS

Earth Filling with Ordinary Soil useful available excavated sand (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15 cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T & P etc., complete for finished item of work.

Supply and delivery of Steel Reinforcement H.Y.S.D. Confirming to I.S.S. including cost & conveyance of all materials , cost of binding wire and its fabrication charges, placing in position tying grills etc., complete. (Fe 500) ( as per amendment vide sl no: 5 of SSR 2011-12 )

Masonry Work in CM (1:6) Prop with Flyash Cement Solid Blocks of size 290X200X140mm for manufacturing of Flyash Solid Blocks using Flyash of 50KGs/ Sqm, Cement of 15 KGs, Gypsum of 5 Kgs and Stone Dust including cost and conveyance of all materials, labour charges, seiniorage charges, scaffolding and curing etc., complete with a compresive strength not less than 75KG/ Sqm for Walls for Walls

Plastering in CM (1:4) 20 mm thick using best river sand from approved source including cost and conveyance of all materials, scaffolding, labour charges, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete., FOR out SIDE

Painting to new walls with 2 coats over primary coat ( total 3 coats )of plastic emulsion paint of approved brand and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc. complete for finished item of work as per SS 911 for External Walls

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for verandah openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with ready mixed Synthetic enamel paint gr-I over a Primary coat (Red oxide metal primer gr-I) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply and fixing of C.C. Kerb not less than M30 strength of size 600(length as directed by the department) X 450 X 110 mm thick with bottom thickness of 110 mm up to height of 400 mm and top width of 50 mm thick chamfering with 45° at starts at 400 mm height to 450 mm height as selected by the Engineer-in-charge from approved source/ factory which is laid on existing CC Bed in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required and including cost and conveyance of all materials & labour charges including transportation charges from approved source, loading & unloading charges to site of work and internal transportation at site including contractor profit & overhead charges complete for finished item of work.

Providing and laying of interlocking concrete block pavements using CC M 35 having thickness 60mm for Medium traffic areas conforming to IS 15658:2006 in all shapes and designs as per the manufacturer's specification of approved shade design with colour pigmentation on top with imported colours etc., laid over a sand bed of 50mm thick using 12mm& down size HBG crushed metal for manufacture of blocks - approved by the department and of approved size & shape of dumbell, zigzag, I-block or any other shape approved by the department., over sand bed of 50 mm average thickness and compacting with vibrating plate compactor having 3 tone compaction force there by forcing part of sand underneath to come up in between joints. final compaction of paver surface to be done after spreading and brushing the fine sand into joints to its final level. The work includes cost of all materials such as cobble stone. inter lock pavers, sand etc., Labour and equipments such as cutting machine, lift, loading & unloading to work site clearing, bringing required for the successful completion of work as per drawings and Technical Specification Clause 1504 MORD and as directed during execution (RBR-CCPV-13-II) P.No: 421

Supply, Delivery and Commissioning of Arch Swing 3.0 Mtr x 1.25 Mtr x 2.8 Mtr.(L x W x H) Thickness of Pipe is 3" support Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Bearing :- The bearings used are “6202” permanent lubricated sealed bearing of repute brand. Bearings are mounted in specially designed M.S. bush.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all Excavation of Ground surface and Concrete work.

Supply, Delivery and Commissioning of Circular Swing 2.0Mtr x 1.25 Mtr x 2.1 Mtr.(L x W x H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Bearing :- The bearings used are “6202” permanent lubricated sealed bearing of repute brand. Bearings are mounted in specially designed M.S. bush.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work.

Supply, Delivery and Commissioning of Four Seater MGR Dia.1.2 Mtr Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.MGR Seat :- Seats are made from best quality F.R.P. material with thickness of 5mm in attractive colours. Bearing :- Bearings are used are of “6209” and “30206” of reputed make. Bearings are mounted in specially designed M.S. bush.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work.

Supply, Delivery and Commissioning of Sea Saw 2.4 Mtr X 0.5 Mtr x 0.5 Mtr (L x W x H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Sea Saw Seat :- Seats are made from best quality F.R.P. material with thickness of 5mm in attractive colours. Bearing :- The bearings used are “6202” permanent lubricated sealed bearing of repute brand. Bearings are mounted in specially designed M.S. bush.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work

Supply, Delivery and Commissioning of Economy swing 2.8 Mtr x 1.2 Mtr x 2.8 Mtr.(L x W x H) Thickness of Pipe is 2" support Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Bearing :- The bearings used are “6202” permanent lubricated sealed bearing of repute brand. Bearings are mounted in specially designed M.S. bush.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all Excavation of Ground surface and Concrete work.

Supply, Delivery and Commissioning of Roto Model Slide 1.5 Meter 3.5 Mtr x 0.6 Mtrsx 2.1Mtrs Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work

Supply, Delivery and Commissioning of Rocking Boat 2.0Mtr x 1.25 Mtr x 2.1 Mtr.(L x W x H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Bearing :- The bearings used are “6202” permanent lubricated sealed bearing of repute brand. Bearings are mounted in specially designed M.S. bush.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work.

Supply, Delivery and Commissioning of Rainbow Climber 3.0Mtr x 0.45 Mtr x 2.1 Mtr.(L x W x H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work.

Supply, Delivery and Commissioning of Animla Spring Rider 0.9Mtr x 0.5 Mtr x 0.80 Mtr.(L x W x H) - Roto Model Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work.

Supply, Delivery and Commissioning of Rocking Boat 1Mtr x 0.30 Mtr x 1.2mtrs Mtr.(L x W x H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Bearing :- The bearings used are “6202” permanent lubricated sealed bearing of repute brand. Bearings are mounted in specially designed M.S. bush.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work.

Supply, Delivery and Commissioning of Flying Butterfly 2.0Mtr x 1.25 Mtr x 2.1 Mtr.(L x W x H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Bearing :- The bearings used are “6202” permanent lubricated sealed bearing of repute brand. Bearings are mounted in specially designed M.S. bush.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work. Including all excavation and Concrete work

Supply, Delivery and Commissioning of Bridge Ladder 2.1 Meter Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work

Supply, Delivery and Commissioning of See Saw Four seated Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work

Supply, Delivery and Commissioning of BIke Spring Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work

upply, Delivery and Commissioning of Spring Duck Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work

Supply, Delivery and Commissioning of Ganesh Play Slide 1.5 Mter Meter Metal:- All pipes make should be Tata or Jindal. All pipes should be of "medium grade" as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.Safety & Maintenance:-All products of equipment should be tested as per EN1176 safety norms and ce certification must. Maintanance should be followed as per EN 1176 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Hardwares :- All Nuts, Bolts,Washers should be of high tensile galvanised material. Including all excavation and Concrete work

Supply, Delivery and Commissioning of Sky walker-1700 mm (L) X 830 mm (W) X 1650 mm (H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.80mm NB:- Prime Stand. Duly bend with CLR 250mm,32mm NB:- Handle frame.25mm NB:- Handle duly bend with CLR115mm,Square pipe 50x50x3 mm :- Paddle footrest frame,Seamless pipe 95mm ID and 105mm OD :- I frame,The foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness. Bearings and Pins:- Bearings 6205 and 6203 should be of SKF 2RS1 type and press fitted for smooth rotation , and does not require relubrication i.e,maintenance-free ball bearing. Pins should be case hardened and centreless finish for life long durability. Footrest :- Foorests are of aluminum pressure casted having size 305x125x26 (LxWxH) with thickness 4.0 mmand of material of grade ADC-12.Pipe end close cap, bearing cap :- SS 304 grade Should be used for protection of pipe end closing duly riveted, bearings and bushes open end closed. Cap Height for 100 NB - 57 mm and for 80 NB - 54 mm. Instruction Sticker: - " Name of Department" Rivetable Instruction sticker 0.8 mm thick SS 304 grade material of size 90mm x 160mm duly laser marked with how to use instructions and tender authority name with logo along with manufacturer details. Customer redressal contacts should be printed on every sticker.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304 material. Including Excavation and Concreting the base of Equipment and installation

Supply, Delivery and Commissioning of Seated Puller Double 1650 mm (L) X 640 mm (W) X 1870 mm (H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.100mm NB:- Prime Stand.32mm NB:- Supporting frame, Handle frame, Seat frame.25mm NB:- Handle hold, Connecting Links.15mm NB:- Support to profile.The foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness. Seat & Backrest :- G.I. Seat of size 330mm X 300mm X 20 mm and 2.0mm thickness duly deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Bearings and Pins:- All bearings of 6205 and 6205 should be of SKF 2RS1 type and press fitted for smooth rotation , and does not require relubrication i.e,maintenance-free ball bearing. Pins should be case hardened and centreless finish for life long durability.Pipe end close cap, bearing cap :- SS 304 grade Should be used for protection of pipe end closing duly riveted, bearings and bushes open end closed. Cap Height for 100 NB - 57 mm and for 80 NB - 54 mm. Base Cover :- SS 304 grade material is used for base cover duly bolted. Size of cover is of Diameter 280 mm with height of 88 mm and 0.8 mm thick.Instruction Sticker: - Rivetable Instruction sticker 0.8 mm thick SS 304 grade material of size 90mm x 160mm duly laser marked with how to use instructions and tender authority name with logo along with manufacturer details. Customer redressal contacts should be printed on every sticker.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304 material. Including Excavation and Concreting the base of Equipment and installation.

Supply, Delivery and Commissioning of Horse Rider -1000 mm (L) X 695 mm (W) X 1000 mm (H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.80mm NB:- Base pipe.32mm NB:- Handle support and Best support.25mm NB:- Connecting Links and Handle.The foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness.Seat :- G.I. Seat of size 330mm X 300mm X 1.8mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. Bearings and Pins:- Bearings 6205 and 6203 should be of SKF 2RS1 type and press fitted for smooth rotation , and does not require relubrication i.e,maintenance-free ball bearing. Pins should be case hardened and centreless grinded finish for life long durability.Rubber:-High quality rubber should be used for the handle grips.Footrest :- Foorests are of aluminum pressure casted having size 305x125x26 (LxWxH) with thickness 4.0 mmand of material of grade ADC-12.Bearing cap :- SS 304 grade Should be used for protection of bearings and bushes open end closed.Instruction Sticker: - Instruction sticker of size 90mm x 160mm of SS 304 grade plate with 0.8mm thickness & duly riveted on 5mm thick MS plate.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304 material. Including Excavation and Concreting the base of Equipment and installation

Supply, Delivery and Commissioning of Rower - 1200 mm (L) X 1000 mm (W) X 800 mm (H)Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.80mm NB:- Base pipe.50mm NB:- Top Seating Frame.32mm NB:- Handle support.25mm NB:- Connecting Links and Handle.15mm NB:- Handle Support40mm NB:- For Shock absorbing PU bush hold.The foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness.Bearings and Pins:- All bearings should be of SKF 2RS1 type and press fitted for smooth rotation , and does not require relubrication i.e,maintenance-free ball bearing. Pins should be case hardened and centreless grinded finish for life long durability.Rubber:-High quality rubber should be used for the handle grips.Footrest :- Foorests are of high quality rubber.Bearing cap :- SS 304 grade Should be used for protection of pipe end closing, bearings and bushes open end closed duly riveted.Instruction Sticker: - Instruction sticker of size 90mm x 160mm of SS 304 grade plate with 0.8mm thickness & duly riveted on 5mm thick MS plate.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304 material. Including Excavation and Concreting the base of Equipment and installation.

Supply, Delivery and Commissioning of Shoulder Builder Double - 900 mm (L) X 600 mm (W) X 1780 mm (H)Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.100mm NB:- Base pipe for prime stand.32mm NB:- Prime Stand support.25mm NB:- Rotating ring duly bend with Uniform diaeter of 880 mm.The foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness.Bearings and Pins:- Bearings 6205 and 6001 should be of SKF 2RS1 type and press fitted for smooth rotation , and does not require relubrication i.e,maintenance-free ball bearing. Pins should be case hardened and centreless grinded finish for life long durability.Knob:-Nylon 6 plastic should be used for the handle knobs.Base Cover :- SS 304 grade material is used for base cover duly bolted. Size of cover is of Diameter 280 mm with height of 88 mm and 0.8 mm thick.Pipe end close cap, bearing cap :- SS 304 grade Should be used for protection of pipe end closing duly riveted, bearings and bushes open end closed. Cap Height for 80 NB - 54 mm. Instruction Sticker: - Rivetable Instruction sticker 0.8 mm thick SS 304 grade material of size 90mm x 160mm duly laser marked with how to use instructions and tender authority name with logo along with manufacturer details. Customer redressal contacts should be printed on every sticker.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304 material. Including Excavation and Concreting the base of Equipment and installation.

Supply, Delivery and Commissioning of Leg Press Double 1730 mm (L) X 380mm (W) X 1550mm (H) Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.100mm NB:- Prime Stand Centre pipe.32mm NB:- Seat frame.25mm NB:- Foot resting frame.The foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness. Seat & Backrest :- G.I. Seat of size 330mm X 300mm X 20 mm and 2.0mm thickness duly deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Bearings and Pins:- All bearings should be of SKF 2RS1 type and press fitted for smooth rotation , and does not require relubrication i.e,maintenance-free ball bearing. Pins should be case hardened and centreless finish for life long durability.Seat & Backrest :- G.I. Seat of size 330mm X 300mm X 20 mm and 2.0mm thickness duly deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Pipe end close cap, bearing cap :- SS 304 grade Should be used for protection of pipe end closing duly riveted, bearings and bushes open end closed. Cap Height for 100 NB - 57 mm and for 80 NB - 54 mm. Base Cover :- SS 304 grade material is used for base cover duly bolted. Size of cover is of Diameter 280 mm with height of 88 mm and 0.8 mm thick.Instruction Sticker: - Rivetable Instruction sticker 0.8 mm thick SS 304 grade material of size 90mm x 160mm duly laser marked with how to use instructions and tender authority name with logo along with manufacturer details. Customer redressal contacts should be printed on every sticker.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304 mmaterial.Including Excavation and Concreting the base of Equipment and installation.

Supply, Delivery and Commissioning of Surf Board Double- 1550mm (L) x 900mm (W) x 1400mm. (H).Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.100mm NB:- Prime Stand Pipe.32mm NB:- Paddle frame duly bend.25mm NB:- Hand rail duly bend.The foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness. Bearings and Pins:- Bearings 6205 should be of SKF 2RS1 type and press fitted for smooth rotation , and does not require relubrication i.e,maintenance-free ball bearing. Pins should be case hardened and centreless finish for life long durability.Footrest :- Foorests are of aluminum pressure casted having material of grade LM-26.Pipe end close cap, bearing cap :- SS 304 grade Should be used for protection of pipe end closing duly riveted, bearings and bushes open end closed. Cap Height for 100 NB - 57 mmBase Cover :- SS 304 grade material is used for base cover duly bolted. Size of cover is of Diameter 280 mm with height of 88 mm and 0.8 mm thick.Instruction Sticker: - Rivetable Instruction sticker 0.8 mm thick SS 304 grade material of size 90mm x 160mm duly laser marked with how to use instructions and tender authority name with logo along with manufacturer details. Customer redressal contacts should be printed on every sticker.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304 material. Including Excavation and Concreting the base of Equipment and installation.

Supply, Delivery and Commissioning of Tripple Standing Twister 1200 mm (Diameter) X 1250 mm (H)Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.100mm NB:- Prime Stand Centre pipe.80mm NB:- Standing twister plate support.50mm NB:- Seating twister plate support.32mm NB:- Bottom frame, support.25mm NB:- Handle frame ring, Foot resting frame.The foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness.Bearings and Pins:- All bearings should be of SKF make 2RS1 type 6007 bearings are used, press fitted for smooth rotation , and does not require relubrication i.e,maintenance-free ball bearing. Pins should be case hardened and centreless grinded finish for life long durability.Pipe end close cap, bearing cap :- SS 304 grade Should be used for protection of pipe end closing duly riveted, bearings and bushes open end closed. Cap Height for 100 NB - 57 mm and for 80 NB - 54 mm. Base Cover :- SS 304 grade material is used for base cover duly bolted. Size of cover is of Diameter 280 mm with height of 88 mm and 0.8 mm thick.Instruction Sticker: - Rivetable Instruction sticker 0.8 mm thick SS 304 grade material of size 90mm x 160mm duly laser marked with how to use instructions and tender authority name with logo along with manufacturer details. Customer redressal contacts should be printed on every sticker.User mannual with exploded diagramas, do and dont's,Trouble shootings,User guidelines as well as customer redressal mechanisms should be mentioned in.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304 material. Including Excavation and Concreting the base of Equipment and installation

Supply, Delivery and Commissioning of Sit Up Board Single-1820 mm (L) X 430 mm (W) X 480 mm (H)Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.50mm NB:- Prime Stand Pipes duly bend with CNC 3 axis pipe bending Machine with CLR 178.00 mm ..50mm NB:- Supporting Frame duly bend and leg support.32mm NB:- Support to bend frameThe foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness.Seat & Backrest :- High quality fibre reinforced plastic (FRP) is used with thickness of 3-4mm which is UV stabilised.Instruction Sticker: - Rivetable Instruction sticker 0.8 mm thick SS 304 grade material of size 90mm x 160mm duly laser marked with how to use instructions and tender authority name with logo along with manufacturer details. Customer redressal contacts should be printed on every sticker.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304.Including Excavation and Concreting the base of Equipment and installation.

Supply, Delivery and Commissioning of Air Walker SIngle - 910mm (L) x 400mm (W) x 1350mm. (H).Metal:- All pipes make should be Tata or Jindal. All pipes should be of "B" class" medium grade as per IS1239 are galvanized and zinc dipped. Prior to finishing all welded joints should scalloped as necessary and welded to an approved MIG process is dressed of removing all sharp edges and burrs. All metal parts should be coated using primer for GI up to 40 microns follwed by powder coating to the thickness of 80-120 microns. Powder and Primer should be of Ackzonobel make.80mm NB:- Prime Stand Pipes duly bend with CNC 3 axis pipe bending Machine with CLR 250.00 mm .32mm NB:- Paddle frame duly bend.25mm NB:- Hand rail duly bend.The foundation used for fixing is a structure and made from center G.I. pipe of 88 mm OD. Welded with M.S. round plate of Ø250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm of M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 2mm thickness. Bearings and Pins:- Bearings 6205 should be of SKF 2RS1 type and press fitted for smooth rotation , and does not require relubrication i.e,maintenance-free ball bearing. Pins should be case hardened and centreless finish for life long durability.Footrest :- Foorests are of aluminum pressure casted having size 305x125x26 (LxWxH) with thickness 4.0 mmand of material of grade ADC-12.Pipe end close cap, bearing cap :- SS 304 grade Should be used for protection of pipe end closing duly riveted, bearings and bushes open end closed.Base Cover :- SS 304 grade material is used for base cover duly bolted.Instruction Sticker: - Rivetable Instruction sticker 0.8 mm thick SS 304 grade material of size 90mm x 160mm duly laser marked with how to use instructions and tender authority name with logo along with manufacturer details. Customer redressal contacts should be printed on every sticker.Safety & Maintenance:-All products of equipment should be tested as per EN16630 safety norms and ce certification must. Maintanance should be followed as per EN 16630 guidelines. The equipment should be withstand for the weight of user more than 100Kg.Test Reports:- Should accopany with Raw material test reports from NABL certified testing laboratories.Hardwares :- All Nuts, Bolts,Washers should be of SS 304 material. Including Excavation and Concreting the base of Equipment and installation.