Construction of new Furnace laboratory in Physics Department at Saurashtra University, Rajkot (Third Attempt)

Item No. Description Qty. Unit FINAL RATE Amount

Excavation for foundation upto 1.5M depth including sorting

out and stacking of useful materials and disposing of the

excavated stuff upto all lead & lift for foundation. In loose or

Excavation for foundation upto 1.5M depth including sorting

out and stacking of useful materials and disposing of the

excavated stuff upto all lead & lift for foundation. In Dense or

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

3 disposing off the excavated stuff upto 50 Meter lead.(C) 130.00 Cu.m 279.81

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

4 disposing off the excavated stuff upto 50 Meter lead.(E) 26.00 Cu.m 597.60

Excavation for foundation from 1.5mt to 3.0mt. Depth

including sorting out and stacking of useful materials and

disposing of the excavated stuff upto all required lead & lift

In Hard Murrum.

Excavation for foundation from 1.5mt to 3.0mt. depth

including sorting out and stacking of useful materials and

disposing of the excavated stuff upto all required lead & lift

Soft rock not requiring blasting

Provdg & laying cement concrete 1:3:6 (1 cement: 3 fine

sand: 6 graded stone aggregate 20 mm nominal size) and

7 curing complete,including cost of form work in Foundation 11.00 Cu.m 3065.41

(A) Foundation and plinth

Providing and laying Controlled cement concrete M.150 for

8 curing complete including cost of formwork in (A) 7.00 Cu.m 4160.88

Providing and laying in position Ready Mixed M-250 grade

concrete for reinforced cement conctere work , using cement

content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in

transit mixer for a up to all lead having continuous agitated

mixer, manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

9 R.M.C. from transit mixer to site of laying, including the cost 24.00 Cu.m 3845.40

of centering shuttering finishing and excluding the cost of

reinforcement including cost of admixtures in recommended

proportions as per IS: 9103 to accelerate/ retard setting of

concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall

be maintained) (Cement level 380 kg) Footing

Providing and laying in position Ready Mixed M-250 grade

concrete for reinforced cement conctere work , using cement

content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in

transit mixer for a up to all lead having continuous agitated

mixer, manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, including the cost

of centering shuttering finishing and excluding the cost of

reinforcement including cost of admixtures in recommended

proportions as per IS: 9103 to accelerate/ retard setting of

concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall

be maintained) (Cement level 380 kg) Column up to all floor

Providing and laying in position Ready Mixed M-250 grade

concrete for reinforced cement conctere work , using cement

content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in

transit mixer for a up to all lead having continuous agitated

mixer, manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

11 R.M.C. from transit mixer to site of laying, including the cost 11.00 Cu.m 6403.50

of centering shuttering finishing and excluding the cost of

reinforcement including cost of admixtures in recommended

proportions as per IS: 9103 to accelerate/ retard setting of

concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall

be maintained) (Cement level 380 kg) Plinth beam

Providing and laying in position Ready Mixed M-250 grade

concrete for reinforced cement conctere work , using cement

content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in

transit mixer for a up to all lead having continuous agitated

mixer, manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

12 R.M.C. from transit mixer to site of laying, including the cost 10.00 Cu.m 6606.81

of centering shuttering finishing and excluding the cost of

reinforcement including cost of admixtures in recommended

proportions as per IS: 9103 to accelerate/ retard setting of

concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall

be maintained) (Cement level 380 kg) Roof beam at all floor

Providing and laying in position Ready Mixed M-250 grade

concrete for reinforced cement conctere work , using cement

content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in

transit mixer for a up to all lead having continuous agitated

mixer, manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

13 R.M.C. from transit mixer to site of laying, including the cost 13.00 Cu.m 6449.66

of centering shuttering finishing and excluding the cost of

reinforcement including cost of admixtures in recommended

proportions as per IS: 9103 to accelerate/ retard setting of

concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall

be maintained) (Cement level 380 kg) Slab at all floor

Providing and laying in position Ready Mixed M-250 grade

concrete for reinforced cement conctere work , using cement

content as per approved Design Mix manufactured in fully

automatic batching plant and transported to site of work in

transit mixer for a up to all lead having continuous agitated

mixer, manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, including the cost

of centering shuttering finishing and excluding the cost of

14 reinforcement including cost of admixtures in recommended 4.00 Cu.m 5733.47

proportions as per IS: 9103 to accelerate/ retard setting of

concrete, improve workability without impairing strength

and durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS 456 shall

be maintained) (Cement level 380 kg) up to floor two level

including finishing the exposed surfaces with cement mortar

1:3 (1-cement:3-fine sand) to give a smooth and even surface

centring and formwork and curing complete excluding cost of

reinforcement,Chhajjah Up to All Floor

Providing and laying controlled Cement Concrete M200 and

curing etc. complete including the cost of formwork and

excluding the cost of reinforcement for reinforced concrete

work for following work. Copping/Lintel/RCC BEND at all floor

Providing TMT Bar FE 500D reinforcement for R.C.C.

16 work including bending, binding and placing in position 8500.00 kg 77.29

complete upto floor two level

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:5 (1- Cement : 5 -fine

sand)(B) Conventional For foundation & plinth

Masonary work using Aerated light weight concrete block

having crushing strength not less than 35 kg/sqcm for super

18 structure above plinth level upto floor two level in cement 31.00 Cu.m 4598.28

mortar 1:5 (1-Cement : 5-Fine Sand) complete as per

Technical Specification up to all floor level

Filling available excavated earth (excluding rock) in trenches,

plinth, sides of foundations etc. in layers not exceeding

cm. in depth consolidating each deposited layer by ramming

Filling in foundation and plinth with Murrum or selected soil

20 in layers of 20 cm. thickness including watering ramming and 30.00 Cu.m 279.47

consolidating etc. completed.

Carring out plinth treatment to by spraying chemical solution

for termite control treatment including labour and material

consistment with I.S.I specification. Using Chlordene and

Chiorpurfiles 20 EC. As Per 6131_paret-II Consentration

21 Weight one percent is recommended i.e one litre 20 EC 85.00 sq.mt 124.35

chemical emulsion with 19 liter give 1 % concrentration

inclusive of one litre chemical emulsion appication at the

rate of 5 Litre chemical / Sqm of surface is recommended as

Providing 15mm thk. Cement plaster in single coat on

brick/concrete walls for interior plastering of following

22 finished even and smooth in Cement Mortar 1:4 (1-Cement : 104.00 sq.mt 221.90

4-Sand) incl. finishing with a floating coat of neat cement

slurry. For All Floor

Providing 10mm Thick Cement Plaster to Ceilling in single

coat for Interior plastering upto all floor level finished even

23 and smooth in Cement mortar 1:4 (1-Cement : 4-sand) 213.00 sq.mt 208.41

finishing with a floating coat of Lime neeru etc.complete for

up to all floor level

20mm thick sand faced cement plaster on walls upto all

height above ground level consisting of 12 mm thick backing

24 coat of C. M. 1:3 (1- Cement : 3-sand) and 8mm thick 209.00 sq.mt 330.72

finishing coat of C.M. 1:1 (1- Cement : 1- Sand) etc.

complete up to all height.

Providing and laying mirror polished Granite 18mm to 20mm

thick in risers of steps,skirting Dedo and pillars laid on 10mm

thick cement mortar 1:3 (1-Cement : 3 coarse sand) and

25 jointed with gray cement slury mixed with pigment to match 15.00 sq.mt 2304.82

the shade of slab including rubbing and polishing etc.

complete. As per Design & Pattern & instruction given by

engineer in charge.

Providing and fixing Double polished kota stone shelves

storage as per detail drawing including all labour and

transportation as approved by engineer incharge. As per

instruction given by engineer in charge.

Construction of Sandwitch type kotah stone Platform 60cm.

width and 75cm. height on resting on both side polished

kotah stone 25 mm thick top,12cm facing pati and 40mm

thick polished kotah stone vertical support fixing by making

grooves with 25mm thick kotah stone slab top including

external edge of the Kotah stone shall be finished with Half

round molding & mirror polished etc. completed. as per

Drawing and as directed by Engineer-in-charge.

Providing and fixing 19mm thick water proof plywood

shutters with both side 1 mm thick Formica including teak

wood Frame size 50 X 35 mm for kitchen / cupboard cabinet

including using approved Formica on shutter and teakwood

decorative batten Patti in front portion with necessary

fixtures,Handle , magnetic and fastening including polishing

work etc. complete and As per instruction given by engineer

Providing and laying polished Kota stone slab flooring over

20mm (Average) thick base of cement mortar 1:6 (1-cement :

6-coarse sand) and as per required Chemical laid over and

jointed with grey cement slurry mixed with pigment to match

the shade of slab including rubbing and polishing etc.

complete. (A)25mm thick

Providing and laying Approved Size full body Vitrified tiles

to 10 mm thick, in skirting risers of steps and dedo on 10mm

thick cement plaster 1:3 (1-Cement : 3-Coarse Sand) and

30 jointed with color cement slurry including finised with flush 65.00 sq.mt 1542.27

pointing & cleaning the surface etc. complete for antiskid

approved Shade & Design & Paterrn as directed by Engineer-

in-charge At All Floor

Providing and laying cement concrete flooring 1:2:4 (1-

cement : 2-coarse sand : 4-graded stone aggregate 20mm

31 nominal size) laid in one layer and finished with a floating 81.00 sq.mt 355.22

coat of neat cement.For All Floor. 50mm Thick (Average), As

per instruction given by engineer in charge.

Providing and laying broken China Mosaic Flooring for

terrace using 12 mm to 20 mm broken pieces of glazed tiles

to be laid over cement mortar 1:3 to plain or slope and to be

32 tempared to bring mortar crème out upto surface using 81.00 sq.mt 779.70

white cement including rounding off junctions and extending

them upto 15 cm along the wall, clearing with water and

oxalic acid etc. as directed.

Providing Cement Vata (10cm. x 10cm. Size ) quarter round

33 in Cement Mortar 1:1 including neat cement 72.00 R.mt 24.28

finishing,watering etc. complete.

Finishing wall with water proofing cement paint of on

wall surfaces (Two coats) to give an approved brand and

manufacture and of required shape even shade after

thoroughly brushing the surface to remove all dirt and

remains of loose powered materials. etc complete

Applying two coats of putty & two coats of primer of

approved brand and manufacture on new wall surface to

35 give an even shade including thoroughly brushing the 317.00 sq.mt 40.59

surface free from mortar dropping and other foreign

matter and sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

surface & celling to give an even shade including throughly

brushing the surface free from mortar droppings and other

foreign matter and sand papered smooth. up to all height

Ceilling painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

surface & celling to give an even shade including throughly

37 brushing the surface free from mortar droppings and other 213.00 sq.mt 94.17

foreign matter and sand papered smooth. up to all height for

a celling and slopping roofs

Providing and fixing standared extruded of alluminium

section of size 63mm x 38.10mm x 1.2mm (Jindal Section

:2434, @ Wt. 0.643 Kg/mt) with colour Powder Coated

38 alluminium frame for ventilation with 5 mm thick frosted 20.00 sq.mt 1175.56

glass as details etc complete for Ventilation. up to all height

and As per instruction given by engineer in charge.

Providing and fixing extruded aluminum window having

extruded aluminum Colour Powder Coated section frame

main outer size 127mm x 38.10mm x 1.35mm ,@ Wt.1.384

Kg/mt,horizontal Four track member size 122.20mm x

31.75mm x 1.10mm @ Wt. 1.205 Kg/mt,vertical member of

size 122.20mm x 31.75mm x 1.50mm ,@ Wt. 1.398 Kg/mt

with sliding shutters of horizontal member size 40mm x

18mm x 1.29mm @ wt.of 0.456Kg/mt,vertical member of

size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt,@ with

39 mm thick transparent bronze colour tinted float glass with 20.00 sq.mt 2140.33

powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as per details

etc complete for window of approved shade & sliding

shutters and providing rubber gasket and Glazing Clips if

necessary around the glass allover including providing heavy

handle, heavy lock, bracket, stoppers. As per drawing or as

per instruction given by engineer in charge.

Providing & fixing M.S. Plain Grills of required pattern to sill

jams of window or wall etc.with m.s. flats at required

spacings & frame all-round, square or round bars with round

headed bolts and nuts or by screws.

Painting Two coats (Including priming coat) on new steel

and other metal surface with enamel paint, brushing,

interior to give an even shade including cleaning cleaning the

surface an even shade including cleaning the surface of all

dirt, dust and other foreign matter.

Providing and fixing 35 mm thick good quality flush door

shutter with 01 mm laminated sheet on both side and

necessary SS and aluminium fixtures and fastening as per

satisfaction of Engineer in charge complete.

Providing Throating of plaster drip and moulding to R.C.C.

Providing and laying machine cut moulded edges machine

polished Granite marble for shelves/sill/jam in walls in Zig

zag pattern 18 mm thick including cutting grooves in walls

and fixing the stone with cement mortar 1:3 and finishing the

same with neat cement slurry in true line and level as

directed . etc. complete. (All Open edges should be Quarter

round polished). As per drawing or as per instruction given

by engineer in charge.

Providing, erecting and fixing double coated Sintex or

equivalent PVC (ISI) Mark Water Tank of required capacity

each with all necessary fittings & connection etc. complete

Providing and fixing in position Collapsible steel shutters

with vertical channesl 20 x 10 x 2 mm braced with flat iron

diagonals 20 x 5 mm size with top & bottom rails of T iron

x 40 x 6 mm with 38 mm dia steel pulleys complete with

bolts, nuts, locking arrangements, stoppers handels including

applying a priming coat with two coat of paint etc. complete

Providing, laying and jointing in true line and level U.P.V.C.

Pipe (SCH-40) line including fitting of approved make list.

Pipe shall be fixed on the wall with the help of clamp at every

two meter C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all

materials.As per instruction given by engineer in charge.

Dia. of 15mm dia.

Providing, laying and jointing in true line and level U.P.V.C.

Pipe (SCH-40) line including fitting of approved make list.

Pipe shall be fixed on the wall with the help of clamp at every

two meter C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all

materials.As per instruction given by engineer in charge. Dia.

Providing, laying and jointing in true line and level U.P.V.C.

Pipe (SCH-40) line including fitting of approved make list.

Pipe shall be fixed on the wall with the help of clamp at every

two meter C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all

materials.As per instruction given by engineer in charge. Dia.

Providing, laying and jointing in true line and level U.P.V.C.

Pipe (SCH-40) line including fitting of approved make list.

Pipe shall be fixed on the wall with the help of clamp at every

two meter C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all

materials.As per instruction given by engineer in charge.Dia.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge , elbow , Door

tee and coupler compression type fittings, wall clips / Chilly

clamp etc. including making good the wall ceiling and

floor.(G)110 mm Including Providing and fixing scaffolding

with H-frame and pipe, chilly clamp system including to and

fro transportation,Excavation & Refilling, Leveling,

loading/unloading erection and dismantling after completion

of repair/ replacement job. Work includes all material,

consumable, tools, tackles complete as per direction of site

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge , elbow , Door

tee and coupler compression type fittings, wall clips / Chilly

clamp etc. including making good the wall ceiling and

floor.(G)75 mm Including Providing and fixing scaffolding

with H-frame and pipe, chilly clamp system including to and

fro transportation,Excavation & Refilling, Leveling,

loading/unloading erection and dismantling after completion

of repair/ replacement job. Work includes all material,

consumable, tools, tackles complete as per direction of site

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge , elbow , Door

tee and coupler compression type fittings, wall clips / Chilly

clamp etc. including making good the wall ceiling and

floor.(G)160 mm Including Providing and fixing scaffolding

with H-frame and pipe, chilly clamp system including to and

fro transportation,Excavation & Refilling, Leveling,

loading/unloading erection and dismantling after completion

of repair/ replacement job. Work includes all material,

consumable, tools, tackles complete as per direction of site

Providing and fixing S.W. gully trap with C.I. grating brick

masonry chamber and water tight C.I. cover with frame of

300mm x 300mm size (inside) with standard weight.(i)

Square mouth traps. (A) 100mm x 100mm size P type.

Providing and fixing PVC SWR Nahni Trap IS 14735 for drain

with jali of the following nominal diameter of self cleansing

55 design with C.I. Scrwed down or hinged grating including the 10.00 Each 614.19

cost of cutting and making good the walls.

Providing and fixing chromium plated brass half trun Valve of

56 approved quality including fixing in pipe line etc. 2.00 Each 275.76

complete.(ii) 32mm dia.

Providing & fixing Wash Basin of Vitreous china size

550x400 mm with single hole for pillar tap with C.I. or M.S.

brackets painted white including cutting holes and making

good the same including C.P. Brass waste, M.I. Fisher union

32mm dia., capstan head, screw down high pressor with

screws,angal cock,back nuts and plastic connection P.V.C.

Waste pipe, Rubber Plug . Etc As per instruction given by

engineer in charge.

Providing and fixing C.P. brass towel rail comlete with C.P.

brass brackets fixed to wooden plugs with C.P. brass

scews.(B) 600mm x 20mm size. As per instruction given by

engineer in charge.

Providing and fixing Brass chromium plated screws down bib

59 tap of 15mm nominal dia. of approved quality and brand.As 2.00 Each 186.83

per instruction given by engineer in charge.

Providing and fixing pillar tap, capstan head, screw down

60 high pressure with screws, shanks and back nuts. (i) 15mm 21.00 Each 308.73

Providing and fixing 25 mm gun metal check or non return

61 full way wheel valve, As per instruction given by engineer in 2.00 Each 420.63

Providing and fixing 32 mm gun metal check or non return

62 full way wheel valve, As per instruction given by engineer in 1.00 Each 314.73

Providing and fixing in position cowel went to pipes.(B)

Providing & fixing in position Cowel went to pipes. 100mm

dia. (As per Pipe Diameter)

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire

of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to 10 mtr

length , in below type of pipe erected with 6A Modular type

switch / bell push & accessories and earth continuity of

65 following type, erected on PVC / Metallic/Wooden box, 25.00 Pt. 375.72

single mounting base frame covered with

textured/metallic/white front plate modules erected on / in

wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed.(e) in existing

pipe erected flushed on wall/ceiling complete Cat.III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected with 6A Modular type switch

and hum free EME step type electronic fan regulator

66 mounted and accessories with earth continuity of following 10.00 Pt. 522.17

type erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed.(e) in

existing pipe erected flushed on wall/ceiling complete Cat.III

Providing and erecting ISI mark Medium class RIGID PVC

PIPES of following size complete to be erected on/in wall or

67 ceiling erected with necessary PVC fittings & Junction boxes 180.00 Mtr. 33.33

fixed with adhesive solution & Clamps with following dia of

pipes, in approved manner as directed (b) 25 mm

Providing and erecting ISI mark Medium class RIGID PVC

PIPES of following size complete to be erected on/in wall or

68 ceiling erected with necessary PVC fittings & Junction boxes 50.00 Mtr. 54.54

fixed with adhesive solution & Clamps with following dia of

pipes, in approved manner as directed (c) 32 mm

Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan

complete with proper insulation without leakage and

Providing Fan clamp of 30 x 5 mm flat of required length &

70 10 mm M.S. Bolt & Nuts erected with necessary hook of 10 10.00 Nos 98.98

mm M.S. Round Bar.

Supplying & erecting fan hook box of 10 mm M.S. round bar

bounded to the RCC bars up to 50mm length each side and

71 pierced through a 16 Gauge M.S. box / Heavy Duty PVC box 10.00 Nos 108.07

complete erected concealed in Ceiling with necessary

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick sheet

Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.) (A) Tube Light with

integral driver (iv) 22-24 Watts, Surge - 2KV,IP-20,

conventional 4 feet Cat-lll

Supplying & erecting single phase approved make industrial

exhaust fan suitable for medium duty ring mounted low

73 noise operation suitable for medium duty having following 10.00 Nos 2054.34

dia size and maximum speed in RPM [A] 305 mm dia

Providing and erecting Approved make Ceiling fan with

double ball bearing ISI mark with condenser A.C. 23OV.50

74 c/s.1200 mm. sweep complete, canopy erected on existing 10.00 Nos 1596.81

hook or clamp with earthing. [Make shall be approved by

Engineer in charge]

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate , modules erected with necessary connections as per

site situation directed by Engineer In charge. (1)One No. SP

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate , modules erected with necessary connections as per

site situation directed by Engineer In charge. (2) One No 5 pin

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate , modules erected with necessary connections as per

site situation directed by Engineer In charge.(5) Electronic

hum Free steps EME Fan regulator Cat.III

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate , modules erected with necessary connections as per

site situation directed by Engineer In charge.(10) 6/16Amp.

Universal socket Cat.III

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate , modules erected with necessary connections as per

site situation directed by Engineer In charge. (9) 16 Amp. SP

one way switch Cat.III

Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed

on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity

of following size (E) in existing pipe (a) 2 wire 1.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed

on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity

of following size (E) in existing pipe (b) 2 wire 2.5 sq. mm

Providing & erecting weather proof, dust & vermin proof,

floor mounted front operated indoor type cubical panel

board necessary IP-42 and above protection as per approval

from engineer incharge made from 14 SWG thick CRC M.S.

sheet for outer body & doors, 16 SWG thick CRC M.S.sheet

for internal partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with

supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips,

rubber grommets, rib, bakelite control fuses/MCB for

82 measuring instruments, earth bus & earth bolts, foundation 1.00 Sq.Mtr 14902.55

flange - bolts-base Plates, sufficient nos. of hinged doors,

handles with locking arrangement and rubber gasket,heavy

duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating.

(The rates excludes the cost of switchgears, bus bars, inter

connecting mains & Copper Aluminium strips, meters, Fuses

etc. The dimension shall be measured excluding base beams)

The panel shall be supplied with following approved

manufacturers with following size. (B) The standard

companies switch gear shall be used and only manufacturers

at CPRI approved factory (i) with 350mm depth

Supplying and erecting HYLAM sheet on existing angle iron

frame.for following thickness (C) 6mm

Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 25 KA. at

415 V,having normal current rating up to 25 A to 100A. with

Fixed thermal & magnetic release suitable to work on A.C.

supply 50 c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S. (Make:-

L&T, ABB, Schnider, Siemens, C&S) ICS=100% of ICU only Cat

Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 35 KA. at

415 V. having Normal current rating 200A.with variable

85 Thermal & magnetic release suitable to work on A.C.supply 1.00 Each 16221.61

50 c/s. with all internal connections, spreader tinned copper

& complete erected in existing 16 (Make:- L&T, ABB,

Schnider, Siemens, C&S) ICS=100% of ICU only Cat III

Supplying and erecting triple pole & neutral 440V / 500V

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

86 wrapped with colour insulating tape for phase sequence of 1.00 R.mt 3202.71

following current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary connections.

(B) Suitable for 200 Amp. capacity

Providing and erecting Sheet Steel powder coated Vertical

MCB distribution board (VTPN) - flush / surface mounted

double door (IP54) fitted with copper insulated busbar,

isolated neutral bar, earth bar and DIN rail, Conforms to IS

87 8623-1 & 3, IEC 61439-1 & 3, suitable for 63/100 AMP TPN 2.00 Each 5817.60

MCCB + RCCB as incomer and three phase outgoing as per

following .(The DBs should be used of same company of MCB

to be used) (A)4 way outgoing (Make:- L&T, ABB, Schnider,

providing and erecting Miniature circuit breaker single pole

6A to 25A suitable to operate on 240 V A.C. system and

88 having breaking capacity 10 KA to be erected in existing box. 36.00 Each 112.11

confirming to IS 8828/1996 with ISI Mark (Make:- L&T, ABB,

Schnider, Siemens, C&S) Cat. III

Providing & erecting 415 V MCB Four Pole for Motor &

Inductive Load (C Curve) having 10KA breaking capacity &

89 confirms to IS :8828 in existing box having following capacity 12.00 Each 737.30

(Make:- L&T, ABB, Schnider, Siemens, C&S) (c)63 Amp. Cat.

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA breaking

90 capacity & confirms to IS : 8828 in existing box having 30.00 Each 299.97

following capacity (Make:- L&T, ABB, Schnider, Siemens, C&S)

(A) 6 to 32 Amp. Cat. III

Providing and erecting Approved make RCCBs conforming to

IS: 12640 and having sensitivity of 30 mA and Short Circuit

withstand capacity of 10 KA and suitable for operation on

phase and neutral 415V,50Hz. having characteristic of quick

action & tripping with all advance feature & do not

incorporate any electronic component for following Max.

rating erected as directed. (Make:- L&T, ABB, Schnider,

Siemens, C&S) (iv) 100 Amps. FP (100 mA Sensitivity) . Cat. III

Supplying & fixing box for housing RCCB + MCB combination

made of 18 SWG sheet steel duly powder coated with gasket,

dust & vermin proof bakelite shield two earthing terminals

for following type of RCCB, RCCB + MCB [a] For 2 pole

Supplying and erecting approved make panel mounting type

Digital Voltmeter having 3 digits LED display, 0 to 750 AC

93 Volts range erected on existing panel board with all 1.00 Each 1275.63

connection, wiring etc .with manufacturers calibration

Supplying and erecting approved make panel mounting type

Digital Ammeter having 3 digits LED display, external CT

operated, calibrated for 0 to 1000 Amps suitable to operate

on 500 Volt AC , erected on existing panel board with all

connection, wiring etc .with manufacturers calibration

Providing & erecting L.T. Current Transformer with bar

primary 50/5 to 1000/5 ratio 15 VA burden erected in

existing CRCA box duly secured with insulating materials

connected to the meter

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on

96 wall with necessary clamps or in existing trench / pipe of 10.00 Mtr. 540.35

following size of cables (F) 3 1/2 core 120 Sq. mm ( 70 Sq.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on

97 wall with necessary clamps or in existing trench / pipe of 100.00 Mtr. 284.82

following size of cables (C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2

Supplying and laying UPVC cable trunking system comprising

unplasticised polyvinyl, chloride rigid material with ignition

free and flame proof confirming BS with necessary end caps

Internal and external bend, flat bends, coupler, tee etc..All

necessary accessories and measuring of following sizes (2)

100 mm x 50 mm trunking

Supplying and laying UPVC cable trunking system comprising

unplasticised polyvinyl, chloride rigid material with ignition

free and flame proof confirming BS with necessary end caps

Internal and external bend, flat bends, coupler, tee etc..All

necessary accessories and measuring of following sizes (3)

mm x 50 mm trunking

providing and erecting Mains with ISI marked, 1.5KV grade

electrolyte multi stranded, annealed copper conductor with

heat resistant PVC insulated conforms to IS 694, IEC -

100 erected in existing pipe of following size (Specifically for 5.00 Mtr. 12.12

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required. (a) One wire 1.00 sq. mm

providing and erecting Mains with ISI marked, 1.5KV grade

electrolyte multi stranded, annealed copper conductor with

heat resistant PVC insulated conforms to IS 694, IEC -

101 erected in existing pipe of following size (Specifically for 5.00 Mtr. 27.27

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required. (c) One wire 2.50 sq. mm

Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987 made

of corrosion free hot dipped G.I.Pipes having Outer pipe dia

of 80 mm having 80-200 Micron galvanising, Inner pipe dia of

40 mm having 200-250 Micron galvanising, connection

terminal dia of 14 mm with constant ohmic value

surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with

chamber and heavy duty cover.(approved make OEM has to

submit test certificate including value of earth resistane of

installation. [B] For Electrical installation up to 11 KV

located in other than normal soil i.e. Soft Rock, Marshy

-Length of Pipe : 2 mtr

-Back filling Compound :1 no. Bag of 25 Kg.

Providing and erecting required size HOT deep Galvanised

103 iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT 20.00 Kg. 77.77

panel board, Motors etc. using proper clamp.

Providing and erecting metallic vitrified danger notice board

104 as per language suggested by engineer incharge for MEDIUM 1.00 Each 69.69

VOLTAGE installation to be erected as per IS-2551.

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC

105 insulated armoured cable complete with out going tails, 2.00 Each 75.75

insulating tape etc for following size of cables. (B) 3 & 1/2

core 35/50 Sq. mm

Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC

106 insulated armoured cable complete with out going tails, 4.00 Each 140.39

insulating tape etc for following size of cables. (E) 3 & 1/2

core 120 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

107 pressure tool & connected to switchgear terminals with 12.00 Each 20.20

brass/cadmium plated nut bolts in an approved manner. (D)

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

108 pressure tool & connected to switchgear terminals with 8.00 Each 45.45

brass/cadmium plated nut bolts in an approved manner. (G)

Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

109 pressure tool & connected to switchgear terminals with 150.00 Each 6.06

brass/cadmium plated nut bolts in an approved manner. (A)