Construction of store room near Shamshan ghat back side of War memorial Dharamshala, Ward No. 8, Sakoh District Kangra H.P. (Under MPLAD Scheme)

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. as directed by Engineer-in-Charge with in all leads and lifts, disposed earth to be levelled and neatly dressed including carriage of materials within all leads and lifts.The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete nominal mix 1:5:10 (One cement isto five sand isto ten graded crushed stone aggregate 40mm (Forty millimeter) nominal size), on ground or under water for all type of structure, in R/wall / B/wall and the like etcetera complete including pumping or bailing out water, dewatering (surface/sub soil water)including removal of slush which may arise at time of laying concrete for all heights/depths including cost of form work and curing complete for 14 (fourteen) days as per drawing and MORD Technical specification section 800, 900, 1200 and 1600 as per entire satisfaction and directions of Engineer-in-charge, including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, toll tax,GST or any other taxes imposed by the Government.

providing and laying Randum rubble masonry brought to courses with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement is to six sand is to twelve graded crushed/broken stone aggregate 20mm (twenty millimeter) nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand) and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced concrete work Grade M-20 (Twenty) design mix to obtain the minimum compressive strength of 20 N/mm2 (twenty newton) per square millimeter) with cement contents not less than 330 kg (three hundred thirty Killogramme) per cubic meter and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in up plinth lavel and the like mass concrete complete as per HPPWD specification or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax or any taxes imposed by the Government.

Filling in plinth with sand of approved quality under floors including watering ramming, consolidating and dressing complete as per HPPWD specifications and as directed by Engineer-in-Charge, including carriage of material within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Stone filling in plinth with approved quality under floor including watering, ramming, consolidating and dressing complete within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) above plinth level upto all floor level in cement mortar 1:6 (one cement isto six sand) and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Centering and shuttering including strutting, propping etc. and removal of form work for Lintels, beams, plinth beams, girders, bressumers and cantilevers as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, Toll Tax Sales tax or any other taxes imposed by the Government.

Centering and shuttering including strutting, propping etc. and removal of form work for Suspended floors, roofs, landings, balconies and access platform as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, Toll Tax Sales tax or any other taxes imposed by the Government.

Centering and shuttering including strutting, propping etc. and removal of form work for Edges of slabs and breaks in floors and walls Under 20 cm wide as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, Toll Tax Sales tax or any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed and vibrated reinforced concrete work Grade M-25 (Twenty five ) design mix to obtain the minimum compressive strength of 25 N/mm2 (twenty five newton) per square millimeter) with cement contents not less than 360 kg (three hundred sixty Killogramme) per cubic meter or as per approved design mix and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in all works above plinth lavel to all floor level to give smooth surface mechanically mixed and vibrated including curring complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering,finishing and reinforcement,including admixtures in recommended proportion as per IS ; 9103 to accelerate, retard setting of concrete improve workability without impairing strength and durability for reinforced concrete work including of material within all leads lifts and other incidentals as per approved specification drawing , design and as directed by the Engineer in charge within all leads lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax,sale tax ,GST and any taxes imposed by the Government.

Providing and laying Tor steel of TATA/SAIL reinforcement thermo mechanically coated bars of grade Fe 500D for Reinforced Cement Concrete work including bending, binding and placing in position complete including cost of binding wire and other incidentals for its completion up to all floor levels as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing angle iron door,window,clerestory window frame manufactured from steel iron section of 40X40X6 mm,thickness including hinges jamb,lock jamb,beed and if required angle thrashold ofmild steel angle 50X25 mm welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in- Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing 1 mm thick M.S sheet garrage door with frame of 40 mmX 40mm X6mm angle iron 3.15 mm m.s gusset plates at the junctions and corners,all necessary fittingscomplete including applying a priming coat of red lead paint..The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and fixing M.S. grills (TATA/SAIL)of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer Fixed to steel windows by welding .all complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Ceiling plaster Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). complete as per HPPWD specifications or as directed by the Engineer-in-Charge including carriage of materials leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeter) thick cement plaster with cement mortar 1:6 (one cement isto six sand) in single coat on rough side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers or rounded angles in all girth and finished even and smooth as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying 15mm (fifteen millimeters) thick cement plaster with cement mortar 1:4 (one cement isto four sand) in single coat on fair side of brick/concrete/ stone walls for interior plastering up to all floor level including arises, internal rounded angles, chamfers and/or rounded angles in all girth and finished even and smooth for septic tank complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and applying white cement (Birla white/JK) /based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Wall painting with acrylic emulsion paint of Asians Paints /Nerolac suraksha /Berger paint approved brand and manufacture to give an even shade: two or more coats , as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Finishing wall with Apex weather proof exterior grade emulsion of Asians Paints /Nerolac suraksha /Bergar paint Exterior Emulsion as per approved shade approved design (Apexultima) on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete , as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge

Painting two coat (excluding priming coat) of Asians Paints /Nerolac suraksha /Bergar paint on previously painted steel and other metal surfaces with enamel paint to give an even shade two or more coatsincluding cleaning the surface of all dirt,dust and other foreign matter and sand papering as required , as per approved drawing, design and specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying (600x 600mm) (six hundred into six hundred milimetres) vetrified tiles in flooring / skiring of Restile/ Nitco/Kajaria / AGL / Simpolo / Somany / Johnson / Agl/Somany as per approved shade and design of the office (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty milimetres)thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (at the rate of three point three kilograme per square metre) including grouting the joints with white cement and matching pigments etcetra complete sqm including grouting the joints with white cement and matching pigments etcetra complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST and any other taxes imposed by the Government..

Providing and fixing 125mm (one hundred twenty five millimeters) fixing oxidized M.S. handles, ISI marked, anodised nodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (one hundred millimeters) fixing oxidized M.S. handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 250x16mm (two hundred fifty into sixteen millimeters) oxidized MS finished sliding door bolts, make of PILOT/Sheel or equivalent anodized transparent or dyed to required colour and shade with necessary bolts, nuts and screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 250x10mm (two hundred fifty into ten millimeters) oxidized MS tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

roviding and fixing 150x10mm (one hundred fifty into ten millimeters) oxidized MS tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etc. complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.