PROVN OF SINGLE OFFICERS ACCN NEAR BLDG NO. T-276 (OFFICERS MESS) WITH BATHROOM AND KITCHEN AT HASIMARA MILITARY STATION UNDER GE (SOUTH) BINNAGURI

Surface dressing not exc. 15 cm deep in soft/loose soil, complete all as per specified and as directed by Engineer-in-charge.

Excavation in trenches n. exc 1.5m wide and n. exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil, complete all as per specified and as directed by Engineer-in-charge.

Removing excavated Soil materials to a distance n exc 50m and depositing where directed at a level n exc 1.5m above the starting point, complete all as per specified and as directed by Engineer-in-charge.

M&L for PCC (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as per specified and as directed by Engineer-in-charge.

M&L for RCC M25 (Design mix) as in Chajjas etc. complete all as specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 10 mm dia. and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge.

M&L for mild steel TMT bars 5 mm to 10 mm dia., cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality conforming to Fe-410-S or Fe-410-O, complete all as specified and as directed by Engineer-in-charge.

M&L for brick work with fly ash old sized Bricks straight or curved on plan in CM 1:4 as in half brick thick walls, complete all as specified and as directed by Engineer-in-charge.

M&L for (10+10) mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 10mm) mixed with water proofing compound in top layer 200 ml per beg of cement or as per manufacturer's instructions finishing the surface fair and even without using extra cement complete all as specified and as directed by Engineer-in-charge. (Note: WPC shall be measured and paid separately as supply only under relevant item.)

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed by Engineer-in-charge.

M&L rendering 15 mm thick on other than fair faces of brick work or concrete block surface in cement mortar 1:6, surface to be finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-in-charge.

S&F of roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Confirming to Fe 410-W (Gde E- 250) quality-A, including steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication complete all as per specified and as directed by Engineer-in-charge.

M&L for plates (plain or chequered), channels, square-cut or notched (ordinary or countersunk), including forming holes without any attachment, with riveted, bolted or welded connections, conforming to Fe-410W (Grade E-250) Quality ‘A’. Steel shall be painted with one shop coat of zinc chromate primer (including surface preparation) at the contractor’s workshop before fabrication, complete all as specified and as directed by the Engineer-in-Charge.

S&F screw bolts (machine made) (diameter = 16 to 20 mm) with hexagonal or square head at one end and screwed the other or screwed both ends to be fitted with washers and one hexagonal or square nut exc. 22.5 cm but n.exc. 30 cm long MS Work as in bands , straps, supports or stays incl bolts, if reqd. , hold fasts, wall ties and similar small articles conforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-in-charge.

S&F MS steel work in tubular trusses including special shaped washers etc., complete using ERW or induction butt welded tubes confirming to IS 1161- 1979 graded St 240 including steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication complete all as per specified and as directed by Engineer-in-charge.

S&F of Pre-painted galvalume aluminium zinc coating GI based corrugated or semi-corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

S&F of Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

S&F of coloured non-skid ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in CM 1:6 complete all as per specified and as directed by Engineer-in-charge.

S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as per specified and as directed by Engineer-in-charge.

Supply and fixing of factory made solid panel factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as per specified and as directed by Engineer-in-charge.

S&F of 75 mm butt hinges, medium weight, cold rolled mild steel and fixed complete all as per specified and as directed by Engineer-in-charge.

All as per serial item No. 127.00 as above but with 2.5 sqmm single core multistranded copper conductor for one socket out let 5/6 AMPs point on the independent board, complete all as specified and as directed by Engineer-in-charge.

All as per serial item No. 127.00 as above but wiring with two single core, multistranded copper conductor of size 4.00 sqmm for 15/16 A socket out let point on independent board, complete all as specified and as directed by Engineer-in-charge.

M & L for preparing new Plastered surfaces of walls and finishing the walls with Acrylic smooth exterior paint of required shade : New work (Two or more coats applied @1.67 Ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 Kg/ 10 sqm), complete all as specified and as directed by Engineer-in-charge.

S & F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal with access door complete all as per specified and as directed by Engineer-in-charge.

M&L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work, complete all as per specified and as directed by Engineer-in-charge.

S&F of 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as per specified and as directed by Engineer-in-charge.

M&L for form work for side of square, rectangular or polygonal pillars, posts, columns & similar works vertical or batter rough finished surfaces of concrete complete all as specified and as directed by Engineer-in-charge.

S&F Pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as per specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated steel or iron surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide, primer over 10cm width or girth complete all as specified and as directed by Engineer-in-charge.

M&L for 75 mm thick PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection with saucer drain / footpath laid in panels and finished even and smooth with using extra cement including necessary form work complete all as specified and as directed by Engineer-in-charge. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

M&L for hardcore of guage not exc. 63mm deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface of broken stone or boulders, complete all as per specified and as directed by Engineer-in-charge.

M&L for 25 mm thick for cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregates) as in sub-base, flooring etc, complete all as per specified and as directed by Engineer-in-charge.

m - 690 gms) and fixed in position complete all as per specified and as directed by Engineer-in-charge.

M&L for providing & fixing factory made solid PVC cup board frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5 mm thick prelam/plain colour PVC sheet reinforce with 19mm x 19mm MS square tube of 19 gauge thickness throughout the frame and metre cut at two corners and jointed with 2 no's of 150mm long brackets of 15mm x 15mm MS square tubes. The door frame shall be fixed to the wall using 100mm long MS screws through the frame by using PVC fasteners. A minimum 4 no's of screws to be provided for each vertical member and minimum 2 no's of screws to be provided to the horizontal member etc., complete all as per specified and as directed by Engineer-in-charge.

M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as per specified and as directed by Engineer-in-charge.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as per specified and as directed by Engineer-in-charge.

M&L for Anti-Termite treatment, treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as per specified and as directed by Engineer-in-charge.

M&L for Anti-Termite treatment, Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as per specified and as directed by Engineer-in-charge.

M&L for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone including griding & polishing with complete all as specified and as directed by Engineer-in-charge. Note : Hole to be provided in granite slab for gas pipe in kitchen platform etc.

Supply and fixing of factory made partly glazed i.e. upper panel will be wire mesh fitted externally in the clear space & lower panel will be plain colour PVC sheet 5mm thick PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as per specified and as directed by Engineer-in-charge.

M& L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe 410-W (Gde E- 250) quality-A, including steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication complete all as per specified and as directed by Engineer-in-charge.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/loose soil complete all as per specified and as directed by Engineer-in-charge.

M&L for PCC 1:3:6 Type C2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as per specified and as directed by Engineer-in-charge.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil, complete all as per specified and as directed by Engineer-in-charge.

M&L for fly ash brick work with old size bricks, straight or curved on plan exc. 6m mean radius in cement mortar 1:6, complete all as per specified and as directed by Engineer-in-charge.

M&L for brick work with fly ash Modular bricks straight or curved on plan in CM 1:4 as in half brick thick walls, complete all as specified and as directed by Engineer-in-charge.

M&L for 40 mm thick PCC 1:2:4, type B0 (using 12.5 mm graded stone agg) for DPC to horizontal or vertical surfaces including necessary form work including mixing WPC as per manufacturer's instructions and complete all as specified and as directed by Engineer-in-charge. (Note: WPC shall be measured and paid separately as supply only under relevant item.)

M&L for applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and as directed by Engineer-in-charge.

M&L for applying Polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sqm, complete all as per specified and as directed by Engineer-in-charge.

M&L for 100 mm thick PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection/ footpath/ steps finished cement concrete surface even & fair etc including necessary form work complete all as specified and as directed by Engineer-in-charge.

M&L for 50 mm thick for cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregates) as in sub-base, flooring etc, complete all as per specified and as directed by Engineer-in-charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 including surface even & smooth without using extra cement, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of cement based paint over a coat of alkali resistant priming paint, complete all as specified and as directed by Engineer-in-charge.

M&L for cement concrete 1:2:4 type, B-1 (using 20 mm graded stone aggregates) as in copings, bed plate, fillets and other similar works including necessary formwork, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed by Engineer-in-charge.

Removing excavated materials (soils) exceeding 1.00 km but n exc. 1.5 km and deposited, complete all as specified and as directed by Engineer-in-charge.

M&L for Plastic dividing strips of 38 mm wide, 1.5mm thick, inserted in position, conform to design, complete all as specified and as directed by Engineer-in-charge.

M&L for MS framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing quality confirming to Fe-410 W (Gde E-250) quality A, complete all as per specified and as directed by Engineer-in-charge.

M&L for Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. confirming to Fe-410 W (Gde E-250) quality A, complete all as per specified and as directed by Engineer-in-charge.

M&L for 75 mm thick PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection/ footpath/ steps finished cement concrete surface even & f

air etc including necessary form work complete all as specified and as directed by Engineer-in-charge.

M&L for fly ash Modular brick work, straight or curved on plan exc. 6m mean radius in cement mortar 1:4, complete all as per specified and as directed by Engineer-in-charge.

M&L for 15 mm thick plastering in cement mortar 1:4 on other than fair faces of brick or concrete surface finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L for Mild steel TMT bars 6 to 8 mm dia. cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed by Engineer-in-charge.

M&L for Reinforced concrete pipes of size 150 mm, class NP2, laid and jointed complete with collars, complete all as specified and as directed by Engineer-in-charge.

M & L for horizontal boring across the existing road without disturbing the road surface for inserting GI pipe, Complete all as specified and directed by Engineer-in-Charge. Note :- GI pipe Shall be measured and paid respective

M&L for 20 mm Drilling and tapping cast iron water mains (in position) for branch connections of the internal dia, complete all as per specified and as directed by Engineer-in-charge.

POINT

Rough excavation not exceeding 1.5 m deep and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge. NOTE:-The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

All as per serial item No. 127.00 as above but for one ceiling/exhaust fan point controlled by one switch.

All as per serial item No. 127.00 as above but for one socket outlet 5/6 AMPs on same board.

M&L for concrete bed 1:3:6 type C2 (40 mm graded stone aggregate) to 150 mm dia. drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as per specified and as directed by Engineer-in-charge.

M&L for precast cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces set in cement mortar 1:4, complete all as specified and as directed by Engineer-in-charge.

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, modular type sunken terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes duly painted with aluminium inside and anticorrosive paint outside, concealed in walls, with modular frame for housing modular type switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be done through proper size copper/brass thimbles. Where concealing of conduit is not feasible i.e. on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost complete all as specified and as directed for one light point controlled by one way switch, complete all as per specified and as directed by Engineer-in-Charge.

S&F of Modular Switch single pole, one way, 6 Amps, 1 module, 230 volts, ISI marked, complete all as specified and as directed by Engineer-in-charge.

S&F of Modular shutter socket outlet 5 pin, 6 Amps, 2 module, 230 volts, ISI marked, complete all as specified and as directed by Engineer-in-charge.

S&F of Modular shutter socket outlet 6 pin, 6/16 Amps, 2 module, 230 volts, ISI marked, complete all as specified and as directed by Engineer-in-charge.

S&F of Modular Switch single pole, one way, 16 Amps, 1 module, 230 volts, ISI marked, complete all as specified and as directed by Engineer-in-charge.

S&F of Modular Bell push 6 Amp, 1 Module, 230 volt, ISI marked, complete all as specified and as directed by Engineer-in-charge.

S&F of modular Metal flush box 1/2 module, complete all as specified and as directed by Engineer-in-charge.

S&F of modular Metal flush box 3 module, complete all as specified and as directed by Engineer-in-charge.

S&F of modular Metal flush box 4 module, complete all as specified and as directed by Engineer-in-charge.

S&F of modular Metal flush box 6 module, complete all as specified and as directed by Engineer-in-charge.

S&F of modular Metal flush box 8 module, complete all as specified and as directed by Engineer-in-charge.

S&F of modular white cover plate with frame 1 module inclusive of inner & outer plate, complete all as specified and as directed by Engineer-in-charge.

S&F of modular white cover plate with frame 2 module inclusive of inner & outer plate, complete all as specified and as directed by Engineer-in-charge.

S&F of modular white cover plate with frame 3 module inclusive of inner & outer plate, complete all as specified and as directed by Engineer-in-charge.

S&F of modular white cover plate with frame 4 module inclusive of inner & outer plate, complete all as specified and as directed by Engineer-in-charge.

S&F of modular white cover plate with frame 6 module inclusive of inner & outer plate, complete all as specified and as directed by Engineer-in-charge.

S&F of modular white cover plate with frame 8 module inclusive of inner & outer plate, complete all as specified and as directed by Engineer-in-charge.

Supply and fix of ceiling rose surface PVC three terminals, PVC/polycarbonate, insulated body, complete all as specified and as directed by Engineer-in-charge.

Supply and fix of Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-charge.

S&F modular electronic step regulator (speed regulation in 5 steps) 120W - 2 module suitable for ceiling fan 1200 sweep/1400 mm, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as specified and as directed by Engineer-in-charge.

S&F of LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and as directed by Engineer-in-charge.

M&L for Moorum/red bajri filling in floors or paving's, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, complete all as specified and as directed by Engineer-in-charge. Note : The Moorum/red bajri work shall be measured after consolidation.

S&F of Harrison rails curtain rod, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as per specified and as directed by Engineer-in-charge.

Supply and fix of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm, complete all as specified and as directed by Engineer-in-charge.

Supply and fix of Single pole and neutral, 240 Volt, 20Amp, enclosure with a two pin and earth plug and socket complete with one single pole MCB, complete all as specified and as directed by Engineer-in-charge.

S&F of providing and fixing factory made uPVG white colour Sliding window (Area exceeding 2.00 sqm each) Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 no's, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories, complete all as specified and as directed by Engineer-in-charge. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.)

Supply and fixing of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engineer-in-charge.

Supply and fix of amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 40 to 63 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing of amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SP 6 To 32 AMP current carrying capacity in the MCB DB complete with connection testing and commissioning, complete all as specified and as directed by Engineer-in-charge.

M&L for sand cushioning (dry) in trenches for protection of UG cables (below, above and around the cable laid in trenches) of 8cm deep before laying and 15cm covering above the top edge of cable after laying, complete all as specified and as directed by Engineer-in-charge.

Supply & Laying of Sub-Class B Bricks, well burnt, laid breadth wise along the length of cable laid in trenches over sand cushion laid for UG cable protection, complete all as specified and as directed by Engineer-in-charge. (Note. The painting shall be carried out through mechanical appliances by the company's approved applicator).

M&L for sub main wiring two run of size 6 sqmm PVC insulated, ISI marked, FRLSH unsheathed, electric power cable (heavy duty) 1100 volts grade with stranded copper conductor with 6.0 sqmm PVC insulated stranded copper conductor earth wire in PVC conduit of suitable size (t

Supply and laying GI tube 20 mm bore medium grade with fittings and fixed in trenches complete all as specified and as directed by Engineer-in-charge.

wo run of 6 sqmm cable and one of 6.0 sqmm wire and one run of PVC conduit will be measured as one unit), complete all as specified and as directed by Engineer-in-charge.

M&L for Straight plain brass ferrules (or connecting screws) screwed both ends and fixed including all necessary fitting such as nippel, reducer socket, socket etc. complete all as specified and as directed by Engr-in-Charge.

Supply, laying & testing of XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100Volt grade on walls with fixing accessories of size 16 Sqmm 2 Core cable, complete all as specified and directed by Engineer-in-charge. Note:- Excavation & earth work, sand cushioning, bricks protection & GI pipe where required shall be measured & paid separately.