PROVN OF TOILET BLOCK GOR GRARD ROOM NEAR BG LINE MAIN GATE AND NEAR MT AREE BLDG NO P 57 AND PROVN OF BOUNDRY PILLARS FOR CERTAIN LOCATIONS AT INF LINES JAMANGAR REV 07 TO 09

Amount

Surface dressing not exc 15 cm deep in soft/loose soil.

Excavation in trenches n.exc 1.5m deep & n.exc1.5m wide on plan in soft/loose soil and getting out.

M & L Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete all as specified.

Demolition of Brickwork or stone/ boulder masonry built in cement motor

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L precast cement concrete block masonry with solid block, type C-1,1:3:6 mix ( using 20mm graded aggregate ), exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil.

Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point.

Spreading,levelling,watering and well ramming the earth filling under floor not exc. 25cm thick in layers.

M & L hardcore of broken stone or boulders of gauge n.exc.63mm,deposited,spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface,complete all as specified and directed.

M & L cement concrete tye D-2, 1:4:8 ( 40 mm graded aggregate ) 75 mm thick as in sub base of floors.

M&L 25mm th PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in flooring, finished fair and even.

M&L non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specfied and directed.

M & L rendering 10mm thick on brick wall or concrete surface in cement mortar 1:4 finished smooth and even complete all as specified.

M&L glazed ceremic tiles in vertical surfaces 300x200x7 mm thick, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specfied and directed.

M & L applying three coat of white wash on newly plastered wall surface including preperation of the surface complete all as specified.

M & L rendering 15mm thick in CM 1:4 on brick wall or concrete surface finished fair and even complete all as specified.

M & L applying two coats of cement base paint on undecorated wall surface including preparation of surfaces ,complete all as specified.

M & L 2nd class hard wood plain,solid, straight,chowkats and frames,wrought,framed rebated on the solid,rounded or chamfered,put together with glue pinned at joints.

M&L 30mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain any numbers, complete all as specified and directed.

M & L sheet glass ordinary quality 3mm thick and glazing with oil putty in squares n.exc. 0 .5 sqm each pane complete all as specified.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications complete or as directed by Engineer-In-Charge.

S&F factory made solid PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for bottom and top rails. MS frame shall be covered heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail& bottom rail on either side & as gap insert for top rail & bottom rail; Panelling for plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, fixing in the frame at the site as per specification.

M & L precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, all as specified and directed.

S&F for Rolled sections as in main and cross beams, hip and jack rafters; Purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates of Fe-410-W(Gde-E-250 quality-A) (framed) etc,complete all as specified.

M&L preparation of new untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified.

M&L applying two coats of synthetic enamel paint over a coat of pink primer to new wooden surfaces exc 10 cm width or girth, including preparation of surfaces, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L 75mm th PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia.complete all as specified.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia.complete all as specified.

S&F 100 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F 75 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F125 mm long,aluminium,anodised, barrel tower bolts of extruded section all as directed.

S&F 125mm size aluminium handles,cast type,anodised all as directed.

Cutting chases, pinning in , not exc 10 cm girth, for concealed water tubing on brick walls, making good to facing where required and pointing in cement mortar 1:3 complete all as directed.

S&F medium grade galvanised steel tubing 15 mm bore with all fittings fixed to wall or laid in floors complete all as directed.

S&F medium grade galvanised steel tubing 20 mm bore with all fittings fixed to wall or laid in floors complete all as directed.

S&F 15 mm dia bib tap cast copper alloy (fency type), chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule all as directed.

S&F stop valve, cast copper alloy, fancy type,chromium plated with long shank and cup (Concealed type), screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe all as directed.

S&F15 mm dia brass chromium plated pillar tap, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut, capstan head, screwed for 15mm dia pipe all as directed.

S & F PVC connection 15x450mm size all as directed.

S&F 10 Ltrs (PVC) white, valveless, syphonic action type, dual type fluhsing cistern, low level with inlet ball valve, float and top push button type, complete all as directed. (Note:- The rate for fixing flushing cistern are deemed to be included with the rate of fixing water closet any type.)

S&F 15mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions all as directed.

S&F 20 mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions all as directed.

S&F vitreous china,white, wash hand basin, flat back size 550x400mm including MS brackets including cutting for and pinning in, but excluding waste pipeall as directed.

Supply and fix 32mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 for wash hand basin all as directed.

S&F 20mm dia brass chromium plated tubular towel rails,D type,60cm long between flanges,complete all as specified.

S&F vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed.

S&Fvitreous china urinals,flat back of size 465mmX355mmX 265mm, white with grating and union for discharge pipe including connecting to waste pipe complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 110 mm dia SWG pipe complete all as specified & directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 110mm PVC (SWR), Junction single, (Single T) equal or unequal), fixed with solvent cement, with oval access door, complete all as specified and directed.

S&F 110mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 75mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 75mm PVC(SWR) vent cowl complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 110mm bore PVC (SWR) 'P' trap, including fixed with solvent cement complete all as specified and directed.

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 110 mm bore drain pipe.

M&L for RCC (1:2:4) type B1 ( using 20mm graded stone aggregete) as in slabs supported on walls and the like

Form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick, complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I.500 ltr capacity incl 15 mm bore Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule all as directed.

M&L for providing precast cement concrete 1:2:4 type B-1 (using 20/15 mm graded stone aggregates) in precast manhole covers all as directed.

Excavating in post holes ( or similar holes ) each n exc 0.5 cum , getting out , returning , filling in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25 cm complete in hard /dense soil all as directed.

M&L for providing plain Cement concrete 1:3:6 type D2 using 40 mm gradded aggregate as in foundation , filling and mass concrete all as directed.

M&L for Providing precast cement concrete 1:1.5:3 (using 20 mm graded stone aggregate) as in posts , boundary pillars , etc. (of any section indicated ), with plain fair faces , including chamfers , weatherings ,throating etc. and placing in required post holes incl necessary use of forms , moulds or machine moulds etc. Note :- 1. Reinforcement shall be measured separately. 2. Rates shall include writing of boundary pillar's No in three digit (e.g. : MES 444) in each pillars .

M&L for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits),with multi stranded copper conductor 1.5 sq mm nominal cross sectional area, single core, pvc insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No in and including medium grade, PVC Concealed conduit of dia not less than 20mm and conduit accessories concealed in wall, ISI marked with valid CML No (IS-9537-1983 for conduits and IS: 3419:1976 for conduit accessories), with mild steel/pressed steel sunken boxes (with earth duly) duly painted with two coats of anticorrosive paint over a coat of red oxide primer internally and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3mm thick Hylam laminated sheet cover for fixing of switches, sockets etc including PVC insulated multi stranded copper conductor 1.5 sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dully complete all as specified and directed at site for the following : (a) One light/ Fan point controlled by one way switch.

S&F switch piano flush type single pole one way 5 Amps 230 V.

Supply& Fixing LED Batten fittings 1ft 5 Watt (min 380 lumens) with clamps incl PVC gutties and flexible wire and connecting to ceiling rose complete . Make:.Wipro Garnet D560565 or eqvt in Jaguar/Philips /Shakti

Supply& Fixing LED Batten fittings 2 ft 10 Watt (min 800lumens) with clamps incl PVC gutties and flexible wire and connecting to ceiling rose complete . Make:.Wipro Garnet D561065 or eqvt in Jaguar/Philips /Shakti

LED light fitting, 1x10 w bulk head luminaries, complete with all accessories and including connection up with twin core twisted flesible copper conductor cable with suitable size of 230v, 50 HZ comple all as specified and directed.MAKE: CG LBHN10CDL / Philips/Wipro /Shakti

Supply and fix Metal body exhaust fan 225/230 mm sweep AC, 240 volts consist of Double ball bearing & Louvers metal body, fixed as per manufacturer instruction, connecting with and including 1.5 Sqmm copper conductor, PVC insulated and PVC sheathed three core cable including making sutable size circular hole in brick / PCC block / stone masonary wall built in cement mortar and making good finishing and painting as existing colour to disturbed surface complete all as specified & directed by Engr in charge. Make :Crompton greaves Trans air / Havells ventilair DB / Bajaj Freshee MKII or eqvt in Orient.

S&F ceiling rose surface backel ISI marked , 2 to 3 terminal all as specified.

S&F DB sheet metal enclosure 4 way Single door SPN. Make:Indoasian /Havells/C&S

S&F MCB SPN 10 to 40 Amps all as specified and rupturing capacity 10 KA, Make:Indoasian /Havells/ABB /Shakti

S&F MCB single pole 5 to 32 Amps all as specified and rupturing capacity 10 KA,Make:Indoasian /Havells/ABB /Shakti

Supply & Laying cable of 6 Sqmm x 2 core, only in trenches / poles / walls XLPE insulated, armoured, Heavy duty electric power cable with aluminium conductor 1100 volts grade with suitable lugs complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches not exc 1.5m wide and not exc 1.5m depth for trenches of pipe line in soft/loose soil all as specified and directed.

Returning, filling in, including spreading, levelling watering and well ramming in layers n.exc 25cm in soft/loose soil etc complete as specified and directed

Removing excavated material to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point.

M&L dry river sand in trenches for cable cushioning & protection including spreading, ramming all as specified and directed.

Supply & Laying precast PCC cable concrete cable cover LV low voltage type -I flat size 250 mm x 150 mm x 40 mm complete

S&F GI Pipe light grade 20 mm for road crossing/ on pole/ on wall for protection of LT Cable.

S&F tube GI medium grade 15mm dia with all fittings laid in trenches all as specified and directed by Engr in charge

S&F stop valve cast copper alloy screw down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union of size 15mm all as specified and directed by engr in charge

Ravi enterprise

M/S Badri Electicals

motwani and associate