SPL REPAIRS BLDG P54A AND P59 OF 31 INF BDE SIG COY AND INCL ROOF,FALSE CEIL WRK BLDG P130 (OR COOK HOUSE CUM DINNING HALL) AD REGT AND PROVN OF GEYSER,CEIL,PADESTAL AND EXHAST FAN AND CALL BELL TO THIS PORTION OF BLDG P273 AT MH AT MIL SN JAMNAGAR

Amount

Dismantling of Asbestos cement /CGI(corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed by the Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering, ridge, cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engr-in-Charge.

Demolition of Brickwork or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by the Engr-in-Charge.

M&L brickwork with old size flyash bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed by the Engr-in-Charge.

M&L Providing cement concrete 1:2:4, type B-1 using (20 mm graded aggregate) as in coping apex stones, bed plates, kerbs, slightly rounded or chamfered angles and throating complete all as specified and directed by the Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for window grills etc complete all as specified and directed by the Engr-in-Charge.

S&F mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails , fixed with angle cleats or other connecting plates, gusset plates, etc conforming to Gde Fe-290 (Gde E- 165)complete all as specified and directed by the Engr-in-Charge.

S&F mild steel work as in band straps, supports or stays for rain water ,ventilating pipes, including bolts, if required; clamps , wall tie, hooks , angle cleats ,hold fast etc and similar small articles conforming to Fe 290, grade E-165 complete all as specified and directed by the Engr-in-Charge.

M&L applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed by the Engr-in-Charge.

M&L for complete removing existing treatment on steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by the Engr-in-Charge.

M&L Framed work such as grills, gates, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks portions framed and hung as gates, and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by the Engr-in-Charge.

S&F Anodised aluminium snap grid frame work wih 20x25mm 'T' and 20x20mm 'L' section with grid size of 605x605mm including with necessary 3.15mm GI wire as in suspended etc complete all as specified and directed by the Engr-in-Charge.

S&F Gypsum ceiling board 60x60cm x8mm thick (pre-finished decorative type) in ceiling fixed with screw as per manufacturers instruction, or as specified and directed by Engr-in-Charge.

Demolition of (reinforced) cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by the Engr-in-Charge.

M & L for RCC (nominal mix ) 1:1.5:3 type A1 (using 20mm graded stone aggregate), as in chajja complete all as specified and directed by the Engr-in-Charge.

Use and waste of formwork to sides and soffits chajja with rough finished surfaces of concrete in flat complete all as specified and directed by the Engr-in-Charge.

M & L for RCC (nominal mix ) 1:1.5:3 type A1 (using 20mm graded stone aggregate), as in beams, lintels over 1.5m span complete all as specified and directed by the Engr-in-Charge.

Use and waste of formwork to sides and soffits of floor or roof beams, beams with rough finished surfaces of concrete in flat complete all as specified and directed by the Engr-in-Charge.

M & L for RCC (nominal mix ) 1:1.5:3 type A1 (using 20mm graded stone aggregate), as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by the Engr-in-Charge.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) with rough finished surfaces of concrete in flat complete complete all as specified and directed by the Engr-in-Charge.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide with rough finished surfaces of concrete in flat complete all as specified and directed by the Engr-in-Charge.

S&F Welded steel wire fabric of weight exc 3.5 kg/Sqm and not exc 4 kg/ Sqm, fixed to steel members with spikes complete all as specified and directed by the Engr-in-Charge.

Removal of all loose/unsound/bad/damaged concrete or plaster existing RCC structure of slab/beams/walls by using chesel/hammar .Cut and remove unsound reinforcement bars, wires etc without damaging the sound reinforcement clean loose rust from bars manually with brush, fixing mild steel welded fabric of weight exceeding 3.5 kg/sqm but n exc 4kg /Sqm with existing bars or by welding on it (supplymentary bars and steel wire wiil be measured and paid separately). Applying epoxy bonding agent and making good with polymer modified plaster as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface in ground floor as following given below :- Modified plaster 15 mm to 20 mm thick in CM 1:4 or PCC 1:1.5:3 type B0 with epoxy bonding agent complete all as specified and directed by the Engr-in-Charge.

M&L for racking of cracks ,preparation and crack filling with polymer modified/chemical based crack fillers by approved manufacturer and filling as per manufacturer instructions in walls,roofs of any type or size (Make: Pidilite/dr fixit,fosroc,boschme or equivalent) complete all as specified and directed by the Engr-in-Charge.

(a)cracks up to 5 mm wide

(b)Cracks exc 5mm but not exc 10 mm

S & F TMT steel bars, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clips, Gde of steel shall be Fe-500/ Fe-500d/ Fe-550/ Fe-550d complete all as specified and directed by the Engr-in-Charge.

S & F TMT steel bars, 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clips , Gde of steel shall be Fe-500/ Fe-500d/ Fe-550/ Fe-550d complete all as specified and directed by the Engr-in-Charge.

S & F TMTsteel bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with & including MS wire (annealed) not less than 0.9mm dia or securing with clips , Gde of steel shall be Fe-500/ Fe-500d/ Fe-550/ Fe-550d complete all as specified and directed by the Engr-in-Charge.

Taking down wooden door/window chowkat or frames exc 1.5 Sqm but n exc 4 Sqm each but with shutters (without taking off shutters from the frames) complete all as specified and directed by the Engr-in-Charge.

Taking down wooden window/ventilators chowkat or frames n.exc 1.5 Sqm each but with shutters (without taking off shutters from the frames) complete all as specified and directed by the Engr-in-Charge.

Taking down of shutters of any description exc 1 sq. m each and n exc 2 sq. m each leaf complete all as specified and directed by the Engr-in-Charge.

S&F Anodised powder coating (minimum thickness of powder coating 50 micron) aluminium frame for doors of 1.50 Kg/Rm, anodised aluminium door shutters, aluminium section weighing 0.55 kg/m, 5.5 mm sheet glass,double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty,Jindal or equivalent duly fitted with neoprene beading, glazing clips, glass panes 12 mm nominal thickness aluminium alloy handles etc.complete all as specified and directed (Make: Jindal/Hindalco/Indal) NOTES: Rates include all joining ,locking arrengements,handles,door stoper,door closer etc for each all doors.)

S&F 2 nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebatedon the solid, rounded or chamfered,put together with glue pinned atjoints, complete all as specified and directed by the Engr-in-Charge.

S&F Factory made solid PVC door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening complete all as specified and directed by the Engr-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and directed by the Engr-in-Charge..

S&F Factory made 35 mm thick framed, panelled shutter (two panel) of 2nd class HW rail and style with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by the Engr-in-Charge.

S&F Factory made 35 mm thick 2nd class hard wood glazed & skeleton door shutters,open rebated and prepared to recive gauge etc(without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and metred beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I, Sec-8 Clause 8.24 (a) etc complete all as specified and directed by the Engr-in-Charge.

S&F 100mm butt hinges, medium weight, mild steel complete all as specified and directed by the Engr-in-Charge.

S&F stainless steel handles, cast type, anodised 150mm long complete all as specified and directed by the Engr-in-Charge.

S&F stainless steel, anodised, barrel tower bolts of extruded section and fixed, 150 mm long complete all as specified and directed by the Engr-in-Charge.

S&F stainless steel, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 250 mm length of bolt complete all as specified and directed by the Engr-in-Charge.

S&F Floor door stopper of stainless steel body and tongue, anodised, over all length of cover plate 140 mm, with hard drawn steel spring, fixed in floor complete all as specified and directed by the Engr-in-Charge.

M&L preparation of new untreated wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by the Engr-in-Charge.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples or with second class hard wood beadings complete all as specified and directed by the Engr-in-Charge.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber gasket and aluminium beading complete all as specified and directed by the Engr-in-Charge.

S&F powder coated aluminium sliding window of 3 tire, frame of section 62mm X 32mm X 1.47 mm or appropriate equivalent section and shutters of section 18 mm X 44 mmX 1.35 mm or appropriate equivalent section fixed with 4 mm thick tinted sheet glass with rubber gasket, handles, locking arrangement and aluminium wire mesh incl making good jambs, cills etc and including taking down old iron window complete all as specified and directed by the Engr-in-Charge.

S&F in coloured aluminium anodised adjustable louvered ventilator, frame of section 63.5mm X 38.1mm X 1.47 mm or higher appropriate equivalent section with aluminium adjustable louvers with 4 mm thick figured/frosted sheet glass with rubber gasket, SS wire cloth 0.36mm dia of wire and average width of aperture 1.40mm incl necessary channel frame work, handles, locking arrangement etc complete all as specified and directed. Note Quoted rates shall include all glazing / SS wire cloth, rubber packing,jointing,cleat, glazing , snap beading etc.

Dismantling boardings, any description, fixed in any position with screws complete all as specified and directed by the Engr-in-Charge.

M & L 18/19mm thick Pre-laminated particle board, interior grade, prelamination one side with decorative choice lamination & other side balancing white lamination, fixed with nails as in cupboards / cabinets incl locking arrangement complete all as specified and directed by the Engr-in-Charge.

S&F 18/19 mm wide 6 mm thick lipping on veneered particle as in cupboard shutter and shelves.complete all as specified and directed by the Engr-in-Charge.

S&F in repairs 2nd class hardwood plain fillet square rectangular in section wrought sawn secured with screws exc 13 & n exc 25 sqcm in section all as specified and as directed by Engineer-In-Charge.

S&F75 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed,tupe C21 complete all as specified and directed by the Engr-in-Charge.

S&F Extruded aluminium alloy handles 100mm long, fabricated type, anodised.complete all as specified and directed by the Engr-in-Charge.

S&F Aluminium anodised 75mm hasp and staple ,safety type with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed by the Engr-in-Charge.

S&F magnetic catches for cabinets of size 50mm complete with striking plate & magnetic stud complete all as per approved sample complete all as specified and directed by the Engr-in-Charge.

M&L 16 to 18mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm screed bed in CM 1:4 complete all as specified and as directed.

M&L 20mm thick Machine cut kota stone as in partition slab, supporting to the granite slab, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engr-in-Charge.

M&L Rounding to edges of 20mm thick granite slabs one edge,such as in window cill, cooking platform, and other similar situations including grinding polishing complete all as specified and directed by the Engr-in-Charge.

Demolition of Stone slabs and tiles (kota stone/granite) laid in cement mortar of any description or thickness in floors, aprons et etc complete all as specified and directed by the Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by the Engr-in-Charge.

M&L Vitrified ceramic tiles light shade 9-10 mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in CM 1:4 complete all as specified and directed by the Engr-in-Charge.

M&L coloured, Non-skid ceramic tiles 7 to 8mm thick (square / rectangular ) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in CM 1:4 complete all as specified and directed by the Engr-in-Charge.

M&L coloured Glazed ceramic tiles in vertical surface 450mm X 300mm X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10 mm thick plaster in CM 1:3 complete all as specified and directed by the Engr-in-Charge.

M&L 20mm thick Machine cut kota stone slab as in flooring over & including 20 mm thick CM 1:4 bedding layer laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engr-in-Charge.

M&L 20mm thick Machine cut kota stone slab as in skirting, riser of steps over & including 10 mm thick CM 1:3 backing coat and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engr-in-Charge.

Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and directed by the Engr-in-Charge.

Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by the Engr-in-Charge.

M&L 75 mm thick Cement concrete 1:3:6, type C-2 using (40 mm graded aggregate) as in plinth protection complete all as specified and directed by the Engr-in-Charge.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A' complete complete all as specified and directed by the Engr-in-Charge.

Demolition of Stone slabs and tiles (interlocking paver block) laid dry of any description or thickness in floors, aprons et etc complete all as specified and directed by the Engr-in-Charge.

M&L for hard core of broken stone boulder of gauge not exceeding 63mm, deposited spread level and layers not exceeding 15cm thick, watered and rammed true surface complete all as specified and directed by the Engr-in-Charge.

M&L for 75mm thick plain cement concrete type D2, 1:4:8 (using 40 mm graded stone aggregate) as in sub base of path, hardstanding, etc complete all as specified and directed by the Engr-in-Charge.

M&L for machine pressed precast concrete interlocking paver block any shape and size jointed and pointed with gray/colour cement and pigment confirming to IS 15658-2006 of 60 mm thickness, M-35 grade including 50mm thick sand for cushioning complete all as specified and directed by the Engr-in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed by the Engr-in-Charge.

S&F in repair 25mm dia stainless steel curtain rail, cut in required length and size to fit with opening incl fixing on bracket with necessary screws fitted on bracket and decorative nobs on sides with necessary arrangement complete all as specified and as directed by Engr-in-charge.

S&F SS Curtain Rod Bracket decorative type suitable for 25 mm dia curtain rod complete all as specified and directed by the Engr-in-Charge.

S&F in repair Rotational moulded polye?thylene water storage tanks of capacity 500 ltrs (cylindrical vertical) with closed top hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by the Engr-in-Charge.

S&F in repair Rotational moulded polye?thylene water storage tanks of capacity 1000 ltrs (cylindrical vertical) with closed top hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by the Engr-in-Charge.

S&F in repair 25 mm bore Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by the Engr-in-Charge.

S&F in repair gun-metal, globe or gate valve with iron wheel, screwed both ends for iron pipe, ISI marked of size 20mm bore , fixed in repairs ,complete all as specified and directed by the Engr-in-Charge.

Taking up/down GI tubing and connections 15 mm size of pipes including all fittings complete all as specified and directed by the Engr-in-Charge.

Taking up/down GI tubing and connections 20 mm size of pipes including all fittings complete all as specified and directed by the Engr-in-Charge.

Supplying and laying of 20 mm dia.(outer dia.) CPVC pipes SDR 11 with plain CPVC SDR 11 fittings jointed with CPVC adesive taflon tape complete to walls/ceiling or laying in floors including all connected brass CPVC fitting complete all as specified and directed by the Engr-in-Charge.

Supplying and laying of 25 mm dia.(outer dia.) CPVC pipes SDR 11 with plain CPVC SDR 11 fittings jointed with sealant solvent leak proof on walls/ceiling or laying in floors including all connected brass CPVC fitting complete all as specified and directed by the Engr-in-Charge.

S&F in repair vitreous china squatting pan, 'Orrisa' pattern, size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including ‘S’ Traps complete all as specified and directed by the Engr-in-Charge..

S&F in repair PVC valveless syphonic action type flushing cistern low level white with inlet ball valve float and handle of capacity 10 litres including brackets complete all as specified and directed by the Engr-in-Charge.

S&F in repairs vitreous china wash basin ovel type, decorative pattern and necessary fittings complete all as specified and directed by the Engr-in-Charge.

S&F repair sinks without drainage board made of stainless steel overall size 610mm x 460mm bowl size 560mm x 410mm x225mm Make - Bluestar, Cat. No. SSHMSB-121 complete all as specified and directed by the Engr-in-Charge.

S&F in repairs15 mm bore pillar tap cast copper alloy, with capstan heads chromium plated, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut, capstan head, screwed for pipe complete all as specified and directed by the Engr-in-Charge.

S&F in repairs 15mm bore Bib taps cast copper alloy chromium plated, fancy type, with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed by the Engr-in-Charge.

S&F in repairs angle cock 15 mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions.complete all as specified and directed by the Engr-in-Charge.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed by the Engr-in-Charge.

S&F in repair Tubular towel rail, brass CP 20mm dia, D type, 60cm long between flanges complete all as specified and directed by the Engr-in-Charge.

S&F in repairs Soap dish, vitreous China white, approximate size 160x 160x90mm18272Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed by the Engr-in-Charge.

S & F in repair grating doom 100mm dia of PTMT(Minimum weight 25gms) fixed in repairs complete all as specified and directed by the Engr-in-Charge.

S & F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) with rubber rings joints fixed in repairs complete all as specified and directed by the Engr-in-Charge.

M&L 32mm dia waste fittings for pipe, brass chromium plated for glazed ware sinks, basins, etc and fly-nuts, flange end bedded in red lead cement and otherend fixed complete all as specified and directed by the Engr-in-Charge.

S&F in repairs 32 mm bore PVC waste pipe with fittings of approved make suitable for WHB, sink etc all as specified and directed.

S&F in repair PVC(SWR) pipe 110 mm dia, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by the Engr-in-Charge.

S&F in repair PVC(SWR) pipe 75 mm dia, single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by the Engr-in-Charge.

S&F in repair PVC(SWR) bend any radius, 110 mm dia complete all as specified and directed by the Engr-in-Charge.

S&F in repair PVC(SWR) bend any radius, 75 mm dia complete complete all as specified and directed by the Engr-in-Charge.

S&F in repair 75mm dia of outlet, PVC (SWR) floor trap, plain with grating including jointing with solvent complete all as specified and directed by the Engr-in-Charge.

Taking down cement plaster any description on brick/stone or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water to receive plaster complete all as specified and directed by the Engr-in-Charge.

M&L for 10 mm thick rendering in CM 1:6 on on stone masonry surfaces of wall and finising even & smooth without using extra cement complete all as specified and directed by the Engr-in-Charge.

M&L for rendering 5 mm thick in CM 1:3 on ceiling to be finished even & smooth without using extra cement complete all as specified and directed by the Engr-in-Charge.

M&L dubbing out average 20 mm thick 1:4 in cement plaster on irregular face of walls complete all as specified and directed by the Engr-in-Charge.

M & L rendering 15mm thick on stone masonry surfaces or other than fair surface of wall consisting two layers of 5mm thick in cement mortar 1:4 over 10mm thick in CM (1:6) finished even and smooth with using water proofing compound complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid saperately.)

Supply only water proofing compound

M&L for preparation of newly plastered surfaces and applying two coats of oil emulsion distemper including one coat of suiatable primer including 3mm thick wall care putty in two layers on wall etc complete all as specified and directed by the Engr-in-Charge.

M&L for complete removal of existing treatment on wall and applying two coats of oil bond distemper over & including one coat of primer including 3mm thick wall care putty in two layers on wall complete all as specified and directed by the Engr-in-Charge.

M&L for preparation of new palstered surfaces and appling three coats of white wash on walls complete all as specified and directed by the Engr-in-Charge.

M&L for complete removal of existing treatment on wall and applying three coats of white wash complete all as specified and directed by the Engr-in-Charge.

M&L for preparation of new plastered surface of ceiling and applying 3 coats of white wash complete all as specified and directed by the Engr-in-Charge.

M&L for complete removal of existing treatment on ceiling and applying three coats of white wash complete all as specified and directed by the Engr-in-Charge.

M&L for preparation of new plastered or unplastered surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed by the Engr-in-Charge.

M&L for complete removal of existing treatment on wall surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed by the Engr-in-Charge.

M & L for reinforced concrete pipes, class NP2, 150 mm dia, laid and jointed complete with collars in trenches and jointed as specified complete all as specified and directed by the Engr-in-Charge.

M & L for concrete bed to drain pipes of 150 mm bore, including packing under, and haunching against the sides of pipes after they are laid and tested cement concrete 1:3:6 type C-2 complete all as specified and directed by the Engr-in-Charge.

M&L precast RCC 1:2:4 type B1 using 20mm graded stone aggregate as in landings, cover slab,chajjas etc.and similar articles with plain faces set in CM 1:6 complete all as specified and directed by the Engr-in-Charge.

Taking down all existing roof treatment and demolition of cement concrete padding/levelling course incl wire brushing and cleaning loose dust etc from surfaces of RCC roof incl flashing and juntion of parapet complete all as specified and directed by the Engr-in-Charge.

M&L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in padding to obtained desired slope and fill the depression and PCC coving etc complete all as specified and directed by the Engr-in-Charge.

M&L for water proofing treatment to non assessible RCC roofs by providing 10mm thick rendering in CM 1:3 mixed with & including water proofing compound @3% by weight of cement & applying one coat of bitumenous primer @ 0.30 kg/Sqm and laying APP based polymeric modifed membrane with polyster non woven reinforced of weight not less than 3kg/Sqm of 3 mm thick with polythene finished sealing with side overlaps of 75mm & 100 mm laps at the ends of membrane by torch application method & applying two coats of aluminium paint (0.20 litre per sqm) complete all as specified and directed.(Note:- Water proofing compound shall be measured and paid saperately.)

Dismanteling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillet complete all as specified and directed by the Engr-in-Charge.

M & L for RCC (nominal mix ) 1:1.5:3 type A1 (using 20mm graded stone aggregate), as in beams, lintels over 1.5m span complete all as specified and directed by the Engr-in-Charge.

S&F Pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of primer complete all as specified and directed by the Engr-in-Charge.

S&F Pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of primer complete all as specified and directed by the Engr-in-Charge.

M&L plain cement concrete 1:2:4, type B-0 using (12.5 mm graded aggregate) in door frames, any size complete all as specified and directed by the Engr-in-Charge.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, 140 mm with hard drawn steel spring, fixed in floor complete all as specified and directed by the Engr-in-Charge.

Dismantling floor kota/granite , hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by the Engr-in-Charge.

M&L Vitrified ceramic tiles light shade 9-10 mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick backing coat in CM 1:3 complete all as specified and directed by the Engr-in-Charge.

M&L 18-20mm thick Machine cut kota stone slab as in flooring over & including 20 mm thick CM 1:4 bedding layer laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engr-in-Charge.

M&L 18-20mm thick Machine cut kota stone slab as in skirting, riser of steps over & including 10 mm thick CM 1:3 backing coat and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engr-in-Charge.

M&L 25mm thick PCC 1:2:4, type B0 (using 12.5mm size stone aggregate) as levelling course complete all as specified and directed by the Engr-in-Charge.

S&F in repairs Vitreous china wash basin, white , flat back , size 550 x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, and restoring connection componants complete all as specified and directed by the Engr-in-Charge.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including 32 mm waste coupling brass, chromium plated with PVC waste pipe for glazed ware basins, etc. with long screwed shanks and fly-nuts complete all as specified and directed by the Engr-in-Charge.

S&F in repair Fancy type Stop valves angle /concealed 15mm bore, cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed incl female brass threaded adaptor on CPVC pipes complete all as specified and directed by the Engr-in-Charge.

M & L rendering 15mm thick on brick wall or concrete surface consisting two layers of 5mm thick in cement mortar 1:4 over 10mm thick in CM (1:6) finished even and smooth with using water proofing compound complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid saperately.)

Excavation in trenches not exc 1.5m wide and not exc 1.5m depth for trenches of pipe line in soft/loose soil complete all as specified and directed by the Engr-in-Charge.

Returning, filling in , including spreading, leveling, watering and well ramming in layers not exc 25cms complete all as specified and directed by the Engr-in-Charge.

Removing excavated material not exc 50 m and depositing where directed at a level not exc 1.5 meter above the starting point complete all as specified and directed by the Engr-in-Charge.

Taking up/down GI tubing and connections 20mm size of pipes including all fittings complete all as specified and directed by the Engr-in-Charge.

Taking up/down GI tubing and connections 25mm size of pipes including all fittings complete all as specified and directed by the Engr-in-Charge.

S&F tube GI medium grade 20mm dia with all fittings laid in trenches complete all as specified and directed by the Engr-in-Charge.

S&F tube GI medium grade 25mm dia with all fittings laid in trenches complete all as specified and directed by the Engr-in-Charge.

S&F gun metal valvs with iron wheel head ,screwed both ends for iron pipe and fixed of size 20 mm complete all as specified and directed.

M & L for XLPE insulated screened PVC bedded galvanised steel strip or wire armoured UG heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area of 25 sqmm 4 core size laid in trenches under floor/roads/hard standing along poles etc complete all as specified and directed by Engr in Charge.

Supply and fixing GI pipe light grade 40 mm bore for cable protection fixed to poles/along wall/floor/under road/across the drain or nallah including taking down old unserviceable GI pipe complete all as specified and directed by Engr-in-Charge .

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe(CPVC) etc.

Supply and fix oscillating Pedestal fan with tilt mechanism and AC single phase 230/240 volt of size 400mm sweeps with 1350 RPM, copper winding, Three speeds controle, Telescopic arrangement with 2 year warranty.( Bajaj, Orient, Atomberg, Havells)

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage230v , 50Hz, RPM 1200, Copper winding of sweeps 300mm complete all as specified and directed by the Engr-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1400mm sweep, min air delivery 245 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by the Engr-in-Charge.

S&F 2 key bed side unit, 150 cm flexible cord, hand remote wall holder , also providing call/ cancel keys with 23A 12 V battery. complete all as specified and directed by the Engr-in-Charge.

S & F Display pannel ( 4 digit, 1 group) , 250 call button capacity, one group show at a time and providing delay reminders caller tone. complete all as specified and directed by the Engr-in-Charge.

S&F wire less signal repeater, range extended to up to 50mtr, used to avoid signal bouncing. complete all as specified and directed by the Engr-in-Charge.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed by the Engr-in-Charge.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed by the Engr-in-Charge.

Taking down ceiling fan/ Exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M Jamnagar complete all as specified and as directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

Description all as per item No 162 here in before but using 4.0 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 15 amps switch socket cobmination point including necessary running of 4.0 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly. (power point) complete all as specified and directed by the Engr-in-Charge.

Description all as per item No 162 here in before but using 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly. (for Geyser & others) complete all as specified and directed by the Engr-in-Charge.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and,cutting chases for concealed water,tubing or concealed conduit wiring,,etc., and making good, cutting not,exc 10 cm girth ®(stone massonary)

S & F for modular switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified and directed by the Engr-in-Charge.

S & F for modular switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified and directed by the Engr-in-Charge.

S & F for modular socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified and directed by the Engr-in-Charge.

S & F for modular socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified and directed by the Engr-in-Charge.

S & F for modular step type fan regulator (BLDC) 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and directed by the Engr-in-Charge.

S & F for modular switch socket combination multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified and directed by the Engr-in-Charge.

S & F for modular step type fan regulator 100/120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and directed by the Engr-in-Charge.

S&F For Switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal , 230 Volts complete all as specified and directed.

S & F for switch Piano type single pole 5 amp, 230 Volts complete all as specified and directed.

S & F for ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6 sqmm cable,one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit complete all as specified and directed by the Engr-in-Charge.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 4 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 4.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 4 sqmm cable,one run of 4 sqmm cable and one run of PVC conduit will be measured as one unit complete all as specified and directed by the Engr-in-Charge.

S & F for sheet metal enclosure MCB DB TPN 4 way with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F Sheet metal enclosures with socket plug top and single pole and neutral enclosure with a two pin and earth plug and socket complete, concealed in wall with one single pole 20Amp MCB SP 'C' series of 240 volts complete all as specified and directed by Engr-in-Charge.

S & F for MCB Tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for ceiling fan, 230 Volts, 1400 mm sweep with mian air delivary 245 CFM, service value of the fan shall be greater than 6.1 (5 star rated) as per BIS with blades, down rod & other necessary accessories with brushless direct current motor (BLDC) with out remote system and electrical connections from ceiling rose to fan teriminal complete all as specified and as directed ( with hanging arrangement)

S & F for ceiling fan, 230 Volts, 1200 mm sweep with mian air delivary 210 CFM, service value of the fan shall be greater than 6.1 (5 star rated) as per BIS with blades, down rod & other necessary accessories with brushless direct current motor (BLDC) with out remote system and electrical connections from ceiling rose to fan teriminal complete all as specified and directed by the Engr-in-Charge.

S & F for LED tube light fitting 2 feet x 10 watts mirror type with high out put diffuser, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting complete all as specified and directed by the Engr-in-Charge.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Make Bajaj Cat part No BCLAB 20W WH LED P, Wipro Cat part No LL20-281-XXX065-ALI or its equvalent in Philips, Havells.

S & F for LED luminaire 600 mm x 600 mm square LED panel 36/30 watts, 220V AC surface type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cable of suitable size with warranty option of 5 years from date of installation complete all as directed by Engineer- in-charge.Make :- Bajaj Cat No BZSSQL 36L LED WH GX or Philips Cat Part No SM366C LED32-6500 PSU OD WH, or Wipro Cat part No CRCO10R036HP57G2.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25/35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make :- Bajaj Cat part No ENXT P 24L WH CR PC SD (Edge plus series) or its equvalent in Philips, Wipro.

S & F for energy efficient exhaust fan of 230 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

S & F for energy efficient exhaust fan of 450 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed by the Engr-in-Charge.

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed(concealed in wall)

S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by the Engr-in-Charge.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc. complete all as specified and directed by the Engr-in-Charge.

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed

S & F for modular plates white colour with frame of 4 module including removal of old unserviceable one complete complete all as specified and as directed

S & F for modular plates white colour with frame of 6 module including removal of old unserviceable one complete all as specified and directed by the Engr-in-Charge.

S & F for modular plates white colour with frame of 8/10 or 12 module including removal of old unserviceable one complete all as specified and directed by the Engr-in-Charge.

S & F for energy efficient exhaust fan of 450 mm sweep heavy duty made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted). complete all as specified and directed by the Engr-in-Charge.

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted. complete all as specified and directed by the Engr-in-Charge.

M/S Badri Electicals (BID ID -3334290)

ABR Trading Co (BID ID -3334071)