SITC of LAN, CCTV Camera And Electrification Work at Shooting Range Maharana Pratap Sports College Raipur Dehradun

Amount

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

8 way (4 + 24), Double door

12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Triple pole and neutral

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 240 sq. mm (62mm)

3½ X 400 sq. mm (82mm)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.

200 mm dia (OD-200 mm & ID-175 mm nominal)

Supply, Installatin, Testing & Commissioning of online 3 phase UPS system with 30 minutes back up including batteries, interconnecting cables, battery rack etc 80 KVA - 3 nos (3 nos x 80 KVA = 240 KVA)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

200 A,36KA,FPMCCB (160 to 200)

Supply of 3.5 c x 240 sq.mm aluminium armoured cable

Supply of 3.5 c x 400 sq.mm aluminium armoured cable

Supply of LED Floodlight luminaire with a single piece housing of non-corrosive high pressure ADC with corrosion resistant powder coating and Anti-dust exposed Lens to ensure protection. The luminaire should have CRI > 70, SDCM <5 and CCT of 5700K and shall be compliant with IP66 and IK08 classification. Luminaire shall be designed to emit at least 38000 nominal lumens with maximum system wattage of 300W at a system efficacy of atleast 135 lumen/watt with narrow beam optics. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 35 deg C. (For 50 mtr target)

The luminaire should have fins on the back to ensure good heat dissipation and to prevent dirt from settling on the luminaire along with aiming angle scale. The electronic driver should be fully integrated and shall have a power factor >0.95 and THD <10% ( at full load) with a minimum inbuilt surge protection of 4kV/kA and external of 20KV and suitable for an operationg voltage range of 140-270V AC. The driver should be BIS approved, fully potted and encapsulated with 440V Stress Voltage protection for 8 Hrs. High Cut off : 325V(+/- 15V) and Auto Restart function should also be available within the fixture. The luminaire should comply with all the required IEC and IS standards and Marine Salt Protection (1000-hr test in lab).

Supply of LED Floodlight luminaire with a single piece housing of non-corrosive high pressure ADC with corrosion resistant powder coating and Anti-dust exposed Lens to ensure protection. The luminaire should have CRI > 70, SDCM <5 and CCT of 5700K and shall be compliant with IP66 and IK08 classification. Luminaire shall be designed to emit at least 21000 nominal lumens with maximum system wattage of 155W at a system efficacy of atleast 120 lumen/watt. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 35 deg C. The luminaire should have choice of Narrow beam, symmetrical wide and asymmetrical wide beam suiting various applications with exposed PC optic lens.

The luminaire should have fins on the back to ensure good heat dissipation and to prevent dirt from settling on the luminaire along with aiming angle scale. The electronic driver should be fully integrated and shall have a power factor >0.95 and THD <10% with a minimum inbuilt surge protection of 4kV/kA and suitable for an operationg voltage range of 140-270V AC. The driver should be BIS approved, fully potted and encapsulated with 440V Stress Voltage protection for 8 Hrs. High Cut off : 325V(+/- 15V) and Auto Restart function should also be available within the fixture. The luminaire should comply with all the required IEC and IS standards and Marine Salt Protection (1000-hr test in lab). (For 50 mtr Middle Area)

Supply of Symetrical Beam Highbay Luminiare,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=180lumens/watt, with a minimum lumen package of 15000with maximum input power of 80W Life of fixture (Including Driver) : 100K Hrs. @ L70B50 Lumen maintenance,Design to work at Ambient temperature (Ta) of 45Degree, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, current ripple <10%, an operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 6KV, 440V P 2 P protection, The fixture design should comply with IS10322, EMC/EMI compliance maintaining driver leakage current as per as per IEC 60598, Protection of Fixture:- IP65,IK08,Class I protection. (For 50 mtr Fring Line)

Supply of LED Floodlight luminaire with a single piece housing of non-corrosive high pressure ADC with corrosion resistant powder coating and Anti-dust exposed Lens to ensure protection. The luminaire should have CRI > 70, SDCM <5 and CCT of 5700K and shall be compliant with IP66 and IK08 classification. Luminaire shall be designed to emit at least 38000 nominal lumens with maximum system wattage of 300W at a system efficacy of atleast 135 lumen/watt with narrow beam optics. The luminaire shall be designed so as to ensure lumen depreciation of up to 30% over 50k burning hours @ design ambient temp 35 deg C. The luminaire should have fins on the back to ensure good heat dissipation and to prevent dirt from settling on the luminaire along with aiming angle scale.

The electronic driver should be fully integrated and shall have a power factor >0.95 and THD <10% ( at full load) with a minimum inbuilt surge protection of 4kV/kA and external of 20KV and suitable for an operationg voltage range of 140-270V AC. The driver should be BIS approved, fully potted and encapsulated with 440V Stress Voltage protection for 8 Hrs. High Cut off : 325V(+/- 15V) and Auto Restart function should also be available within the fixture. The luminaire should comply with all the required IEC and IS standards and Marine Salt Protection (1000-hr test in lab). (For 25 mtr target)

Supply of Symetrical Beam Highbay Luminiare,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=180lumens/watt, with a minimum lumen package of 15000with maximum input power of 80W Life of fixture (Including Driver) : 100K Hrs. @ L70B50 Lumen maintenance,Design to work at Ambient temperature (Ta) of 45Degree, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, current ripple <10%, an operating Voltage Range of 140 - 270 V. Minimum Internal Surge Protection 6KV, 440V P 2 P protection, The fixture design should comply with IS10322, EMC/EMI compliance maintaining driver leakage current as per as per IEC 60598, Protection of Fixture:- IP65,IK08,Class I protection. (For 25 mtr Firing Line)

Supply and fixing of L.T panel made of CRCA sheet steel dust & vermin proof with 400 amp MCCB as incommer with change over switch and outgoing 100 amp MCCB 01 no, 63 amp FPMCB 07 no, 40 amp FPMCB 02 nos with suitable size of busbar, indicating lamp complete in all respect.

Supply and fixing of copper bonded chemical earthing with G.I earth strip complete as per I.E rules

Supply and fixing of main feeder pillar made of CRCA sheet steel dust & vermin proof with incommer 800 amp FPACB 50 KA microprocessor based with O/L, S/C & E/F protection release, auxiliary contractor, TNC switch, RYB phase indication lamp, On/Off/Trip/S.charge indication lamp, digital multifunction meter, CT's for metering, 2 nos 630 amp FPACB for 2 nos D.G set with bus coupler section with D.G synchronization system with fully load operation and outgoing 250 amp FPMCCB 03 no, 100 amp FPMCCB 1 no, 200 amp FPMCCB 02 no, 160 amp FPMCCB 02 nos, 63 amp FPMCB 01 no, 25 amp FPMCB 04 no with suitable size busbar complete in all respect.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

3 run of cable

Supply, installation, testing and commissioning of Layer III Ethnernet switch : 24 port RJ45 10 base 1000 T (POE) with 2 nos uplink fiber ports

Supply, installation, testing and commissioning of Layer II Ethnernet switch : 24 port RJ45 10 base 1000 T (POE) with 2 nos uplink fiber ports

Supply, installation, testing and commissioning of 1 Giga Fiber Module

Supply, installation, testing and commissioning of signal port I/O with SMB

Supply, installation, testing and commissioning of 1 mtr patch cord

Supply, installation, testing and commissioning of 3 mtr patch cord

Supply, installation, testing and commissioning of 24 Port patch Panal

Supply, Installation, Testing & Commissioning of 18 U rack complete with all accessories etc complete as per specifications and as required.

Supply, Installation, Testing & Commissioning of 42 U rack complete with all accessories etc complete as per specifications and as required.

6 Core Fiber Cable with laying , termination of fiber optic cable and requires accessories

Configuration, Installation Charges with One Year Onsite Warranty Support

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

3 run of cable

Supply, Installation, Testing & Commissioning of 64Ch Embedded Network Video Recorder with 8 HDD Bays Supports 4K Cameras, HDMI, VGA and ONVIF Camera

Supply, Installation, Testing & Commissioning of IP (Network) motorized Varifocal lens (2.8-12mm MFZ) bullet camera 2 megapixel, Progressive scan, CMOS, with 1920X1080 resolution @25 fps,WDR 120dB, 3D DNR, True Daynight,0.005 lux color sensitivity, 0 lux with IR upto 30 mts,IP66, rated, with POE, onboard storage upto 128GB micro SB card support, motion detection along with privacy masking. The camera shall be UL, CE, FCC certified. Complete with mounting bracket and all necessary accessories, civil, electrical works & peripheral items, as required.

Supply, Installation, Testing & Commissioning of 2 MPX IP (Network) Motorized Verifocal lens 2.8 - 12mm MFZ, Vandal Proof Dome Camera Progressive scan, CMOS, with 1980X1080 resolution @25 fps,WDR 120dB, 3D DNR, True Daynight,0.01 lux color sensitivity, 0 lux with IR 30 mts, IP66, IK10 rated, with POE, onboard storage upto 128GB micro SB card support, motion detection along with privacy masking for Parking Area. The camera shall be UL, CE, FCC certified. Complete with mounting bracket and all necessary accessories, civil, electrical works & peripheral items, as required.

Supply, installation, testing and commissioning of Layer II Ethnernet switch : 24 port RJ45 10 base 1000 T (POE) with 2 nos uplink fiber ports

Supply, installation, testing and commissioning of 1 Giga Fiber Module

8 TB HDD (Surveillance)

Supply, Installation, Testing & Commissioning of 9U rack complete with all accessories etc complete as per specifications and as required.

Supply, Installation, Testing & Commissioning of 18 U rack complete with all accessories etc complete as per specifications and as required.

Intel Xeon Server Max Number of sockets available on chipset 2 populated with processor 2 Number of core per processor 8 or more Processor configuration Inter Xeon silver or higher series PCI slots ( Express Gen 3.0) 1 or more Type of RAM DDR4 SDRAM with ECC RAM Size (GB) 64 RAM upgradable upto (GB) 256 or more Type of Hard Disk Drive SAS Total number of SAS slots At least 08 Hard disk drive capacity per SAS (GB) 480 or more Total capacity offered with SAS (GB) 1440 or more RAID controller cache (GB) 1 or more RAID type RAID 5 or higher LAN ports (1G/10G) 2 or more Video controller ( support VGA or above resolution) Yes Keyboard / Mous

Supply, Installation, Testing & Commissioning of 65 " LED 7 X 24 Duty Cycle Commercial Display for CCTV

Supply, Installation & Testing of 6 Core Fiber Cable with laying , termination of fiber optic cable and requires accessories

Supply, Installaton & Testing of Enclosure Box for IP Camera

Supply, Installation & Testing of HDMI Cable 5 Mtr

NVR Configuration, Rack Mounting & IP CCTV Camera Installation Charges with One Year Onsite Warranty Support

SHREE BALAJI ASSOCIATES (BID ID -353368)