Renovation of Har ki Pauri in Haridwar Distt. Haridwar Under Namami Gange Programme

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent mix)

"Disposal of moorum/ building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-Charge.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Earthwork in excavation by mechanical means(Hydraulic excavator) / manual means over areas(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm. on plan) including getting out and disposal of excavated earth lead upto 50 m. and lift upto 1.5 m , as directed by engineer -in -in charge.All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches,plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 Cement :2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:1.5:3 (1 Cement: 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth

Supplies and stacking 63 mm to 45 mm size stone aggregate (Hard core base)

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx2.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal embers/bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 2.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/ direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work).

Provinding and Applying one coat of approved primer of Asian paint /ICI and two coats of apex. Ultima of asian paints or weather shield max of ICI(as per manufacturer's specification) to the entire external surface of the building after scrpping, burshing, cleaning, washing the surface and including scaffolding, curing, filling, the crevices and cracks with filler materials, leveling etc.m all complete.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landing,balconies and access plateform

Wall(any thickness) including attached pilasters,butteresses,plinth and stringcourses etc.

Lintels,beams,Plinth,beams,Girders,Bressumers and Cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab upto 0.50 sqm

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.All works above plinth level upto floor V level.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, olumns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing andreinforcement : 1:1.5:3 (1 cement : 1.5 coarse and(zone-III) : 3 graded stoneaggregate 20 mm nominal size)

Half bricks masonry with common burnt clay F.P.S.(non modular)bricks of class designation 7.5 in superstructure above plinth level up to floor V level cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S.(non modular)briks of class designation 7.5 in foundation and plinth in: cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S.(non modular)briks of class designation 7.5 in foundation and plinth in:

Extra for providing and placing in position 2 Nos 6mm dia M.S. bars at every third course of half brick masonry

Brick work with common burnt clay F.P.S.(non modular)briks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:cement mortar 1:6 (1 cement : 6 coarse sand)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S.Tube

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations. (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by ngineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing ompound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge. With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing LED flood light 30 W.Cat. Reference : BVP 161 LED

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge,

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Gang saw cut stone 30mm thick Red sand stone

40 mm thick rubbed Red Sand stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick side buttered with cement mortar 1:2 (1 cement :2 stone dust ) with admixedpigment to match the shade and pointing with same mortar Red Sand Stone

Extra for pre finished nosing in treads of steps of Red Sand Stone slab.

Kota stone slab flooring over 20 mm.(average)thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab,including rubbing and polishing complete with base of cement mortar 1:4(1 cement :4 coarse sand):25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :Raj Nagar plain

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse and(zone-III) : 3 graded stone aggregate 20 mm nominal size).

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)

12 mm cement plaster of mix :1:6(1 cement: 6 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Finishing walls with textured exterior paint of required shade:New work (Two or more coats applied @ 3.28 Litr./10 sqm )over and including priming coat of exterior primer applied)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes

SOUND SYSTEM........Supply, installation, testing & commissioning of one unit of 12 no. Bosch make 2 way Musical Horn in ABS housing . . Unit is a combination of re-entrant horn and 2 transducers one for low frequency and the other for high frequency . Unit is weather protected and suitable to use in high humidity areas, The horn loudspeaker has built-in protection to ensure that, in the event of a fire, damage to the loudspeaker does not result in failure of the circuit to which it is connected. Maximum power: 45 Watts Power tapings: 4 SPL at rated power / 1 watt : 115dB /100dB Horizontal 68° / 68° Vertical 98° / 118° Rated input voltage 70 / 100 V Rated impedance 167 / 333 ohm All Bosch loudspeakers are designed to withstand operating at their rated power for 100 hours in accordance with IEC 268-5 Power Handling Capacity (PHC) standards. CERTIFICATIONS Safety acc. to EN 60065 Emergency acc. to EN 54-24 / BS 5839-8 / EN 60849 Self-extinguishing ABS acc. to UL 94 V 0 Water and dust protection acc. to IEC 60529, IP 65 Wind-force acc. to NEN 6702 + A1, Bft 11 including 1 no. Bosch make Booster amplifier 480 Watt , Temperature controlled forced front to back ventilation, directly stackable The amplifier is protected against overload and short circuits. A temperature-controlled fan ensures high reliability at high output levels and low acoustic noise at lower output levels An overheat protection circuit switches off the power stage, if the internal temperature reaches a critical limit due to poor ventilation or overload. Input The system has two balanced inputs with prior Inrush current : 19 Amp Freq response : 60 to 18000 Hz, S/N Ratio > 90 dB, with ................1 no. Bosch Dynacord 10 Channel Mixer having 2 high quality editable effects, digital effect devices offering 100 factory + 20 user presets , professional 4x4 24 bit / 96 KHz USB interphase with MIDI, equipped with 11 band stereo graphic equalizer tap delay presets, unit is equipped with equalizer Unit has builtin anti feedback filter in the master , Phantom power switchable in groups, Mice channels . Unit has 6 mono + 4 Stereo Line inputs, Switchable voice filter mono inputs. Display 128 x 64 pixel OLED, Unit comes with dust cover, with .......................1 no. Bosch cardiode hand held wired unidirectional mic for general purpose , Freq 80 to 12000 Hz, sensitivity 1.7 mV/pascal , rugged body in dark grey finish LBC 2900, with ............1 metre 2 core 2.5 Sq mm armoured copper cable balanced LS grade Asian make, Installation of Horn Speaker on clamps for poles. Connections using patch cords & integration of amplifier with mixer complete in running condition inc. all costs etc. complete..

Providing and fixing Waterproofing canopy tensile fabric over ms work i/c all necessary arrangement complete all respect.

Extra for plastering done on moulding, cornices or architraves including neat finish to line and level:In two coats

66mm overall thickness partition using 8mm thick double skin multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS : 14862 with suitable fibre cement screws

Supply & Fixing of 30 mm thick GRC Pannel with jali i/c all necessary arrangement complete all respect.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.

Providing and fixing bright finished brass handles with screws etc. complete:125 mm

Mural Relief Work- Regional culture at arrival exit. 2- Dimensional fibre art work depicting our regional reich culture will be created of according as shown in the drawing Mural/sculptural embossed art work shall be created in the media of clay on wooden base according to the drawing initially Art work shall be made with clay in accordance to the drawing after completing

Supplying & fixing Engraving in sand stone with colour

Washed stone grit plaster on exterior walls height upto 10 metre above ground level, in two layers, under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand ), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2 Kg of cement per square metre, top layer 15 mm cement plaster 1:1/ 2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10 mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings ,complete as per specification and direction of Engineer-in-charge

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment).Overhead informatory road signage

Providing an fixing signage on S.S sheet 4 TO 5 MM .Thick as per design

Supply and Fixing of Solar street Light: Moudle 2W,2000Lumen,Integrated Solar LED street light with microcontroller Based integrated MPPT Charge Controller and driver.Cat. Refference : BRP710 LED20 CW AOR S1 12 V LFP AIO Solar , Pole and Structure (5.0 M) for all in one solar LED Street Light including Construction of concrete base mixture as relevant,laying,jointing,installation and Transportation etc. Inclusive of all.

Supply & Fixing of 12 mm thick WPC Jali

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488kg/sqm mixed with water proofing cement compound @ 0.253kg/sqm.(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 20 mm nominal bore

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outle Sand cast iron S&S as per IS: 3989

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5

Trash bins :2 wheeler of 120 Ltr.capacity size :D 480XD 550X H 940 mm. i/c all required cost complete etc.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole,300 mm apart including drilling 12mm diameter holes and plugging with cement mortar 1:2 (1 cement :2 coarse sand )to match the existing floor: Whith Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 12.5 mm nominal size)

Providing and fixing ISI marked flush door shutters conforming to IS :2202(Part I) decorative type ,core of block board construction withframe of 1st class hard wood and well matched teak 3 ply veneers with vertical grains or cross bands and face vaneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

35 mm thick factory made Solid panel PVC Door shutter made out of single piece extruded solid PVC profiles, 5 mm (± 0.2mm) thick, having styles &rails (except lock rail) of size 95 mm x 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner . Non decorative finish (matt finish).

Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc.300x16 mm

Providing and fixing ISI marked oxidised M.S.handles conforming to IS:4992 with necessary screws etc. 125mm

Providing and fixing oxidised M.S.casement stays (straight peg type)with necessary screws etc.300 mm weighing not less than 200 gms

Providing and fixing ISI marked oxidised M.S. Tower bolt black finish,(Barrel type) with necessary screws etc.complete: 250x10 mm

Providing and fixing ISI marked oxidised M.S. Tower bolt black finish,(Barrel type) with necessary screws etc.complete: 150x10 mm

Providing and fixing aluminium hanging floor door stopper,ISI marked, anodised (anodic coating not less then grade AC 10 as per IS:1868)transparent of dyed to required colour or shade,with necessary screws etc.complete Single rubber stopper

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Secondclass teak wood 35 mm thick

Providing and fixing PVC Door Frame of size 50x47mm with a wall thickness of 5 mm (± 0.2 mm) made out of single piece extruded PVC profile, with mitred cut joints and joint with 2nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8x100mm long anchor asteners complete, all as per manufacturer's specification and direction of Engineer -in- charge.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multichambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screwsProfile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately)Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/top hung Upvc windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge.200 x 19 x 1.9 mm

Providing and fixing casement handle made of zinc alloyed (white powder coated) for UPVC casement window with necessary screws etc. complete.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: Fixing with adjustable lugs with split end tail tomeach jamb

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.Coupler 110mm

Bend 87.5 degree 110mm bend

Shoe (Plain) 110mm shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs,screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement :4 coarse sand )and making good the wall etc. complete. 110 mm

Providing and Laying Firstly clean surface with wire and grass brush for remove all dust and loose particles and surface making it dust free with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges etc.Providing and Laying bond coat of SIKA LATEX(SBR Based multipurpose polymer for water proofing and repair)Providing and applying 20 mm thick layer of SIKAREP MICROCRETE(Ready to use non shrink cementitious micro concrete ) as per manufacture's specification over surface duly prepared and repaired including all cost of materials,labour and T& P Etc. for proper completion of work.

Dismantling wood work in frames, truses,purlin and rafters upto 10 mtr. Span in 5.0 mtr. Height i/c stacking the materials within 50 mmtr. Lead : of sectional area 40 sqm. And above .

Renewing wooden beams in roofs i/c making good the hools in wall and painting with oil type wood preservative of approved brand and manufacturing complete i/c removal of rubbish to the dumping ground, all complete as per Direction Engineer in charge above 4,0 m and upto 5,0 m lenth.Sal wood Beams.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Supply and Fixing of Solar street Light: Moudle 28 W 4500Lumen,Integrated Solar LED street light with microcontroller Based integrated MPPT Charge Controller and driver.Cat. Refference : BRP710 LED45 CW AORS1 12 V LFP AIO Solar, Pole and Structure (5.0 M) for all in one solar LED Street Light including Construction of concrete base mixture as relevant,laying,jointing,installation and Transportation etc. Inclusive of all.

Providing & Fixing cast iron Bench Approximate weight 1.05 Qtl. Including cost of painting, fixing etc.complete in all respect…

Providing & Fixing 02 No. Dustbin Trash bins :2 wheeler of 120 Ltr.capacity size :D 480XD 550X H 940 mm.

Supply and stacking at site Moorum

Supplying,stacking and spreading 6mm thick red bajari,watering and rolling complete including preparation of the surface and rolling.with Road Roller/Hand Roller

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. In Diffrent Colours

Supply and stacking of Bombax ceiba plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Nauclea cadamba (Kadam) plant of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.v

Supply and stacking of Bassia latifolia (Mahua) plant of height 90-105 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and Displaying of of Cuphea chinensis plant of ht. 30-45 cm full of branches and healthy foliage in 25 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Supply and stacking of Azadirachta indica ( Neem ) plant of height 120130cm in big polybag of size 25 cm as per direction of the officer-in-charge. ge.

Supply and stacking of Butea frondosa (Flame of Forest) plant of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Cassia fistula (Amaltash) plant of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Cassia javanica plant of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Erythrina indica plant of height 150-165 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Ficus religiosa (Peepal) plant of height 150-165 cm. in big poly bags of size 30 cm as per direction of the officer-in-charge.

Supply and stacking of Mangifera indica (Mangografted ) plant of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-incharge.

Supply and stacking of Michelia champa (Golden Champa)plant of height 90-105 cm. in earthen pots of size 25 cm as per direction of the officerincharge

Supply and stacking of Millingtonia hortensis plant of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.v

Supply and stacking of Mimusops elengi (Maulsri) plant of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Pinus longifolia (Pinus) plant of height 90-105 cm. in cement pots of size 35 cm as per direction of the officer-in-charge.

Supply and stacking of Tectona grandis (Teak) plant of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Melia azedarach plant of height 120-135 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge

Providing and Displaying plants Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Supply and stacking of Ficus Benghalensisi height 120-135 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge

Supply and stacking of Ficus Racemosa height 120- 135 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge

Supply and stacking of Purnus persica height 120- 135 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge

Supply and stacking of sapindus mukorossi height 120-135 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge

Supply and stacking of santalum album height 120- 135 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge

Providing and Displaying plants Chrysenthemum single variety in different colour well developed having 45 to 60 cm ht., minimum 100 and above half bloom flowers open well stacked with bamboo stick having three layer tiding by thread fresh and healthy foliage in 25 cm Earthen Pot and as per direction of the officer-in-charge. .

Supply and stacking of plant Nerium oleander (kaner) of height 45-60 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge.

Supply and stacking of Jasminum grandiflorum (chameli) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Supply and stacking of plant Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-incharge

Supply and stacking of Allamanda cathartica plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-incharge

Sunflower Dwarf ( one Set 100 plants)

Vinca Hybrid( one Set 100 plants)

Gaillardia Double( one Set 100 plants)

Salvia( one Set 100 plants)

Rose plant

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Spreading of Sludge Farm Yard Manure or/and good Earth (Spreading of sludge farm yard manure or/ and good earth in required thisludge, farm- yard manure or/and good earth to be paid for separately)) Screened through sieve of I.S.designation 20 mm

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.external work) 50 mm dia nominal bore

25 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :50 mm nominal bore

25 mm nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

50 mm nominal bore

Providing & Fixing Bore well of Transportation of ring machine,air compressor,OP unit,camp equipage connected T & P and necessary materials required for drilling up to site .Drilling of Borehole from GL to 30 Mtr. Deep odex drilling of maximum pilot bore size 152 mm after remaining i/c water arrangement for drilling back ashing collecting of sample from different strata,preparing and submitting strata chart etc.complete.with 5 Hp Submersibble Pump of Crompton Greaves including all wiring casing pipes ,Development , Structure etc. all complete in all respect as per site incharge

Supply, installation, testing & commissioning of LED Display system P 6.94 of LG, SONY and Samsung brand of display size 18.044 x 9.84 feet, with LED video processor, Pitch Name P6.9, Encapsulation Bonding Wire of gold. Physical Parameters - 3 in 1 SMD Pixel Configuraiton, Pixel Pitchof 6.94mm, Module Resolution (WxH) 36x72, Module Dimensions(WxH,mm) of 250x500, Weight per Module 1.80 kg, No. of Modules per Unit Case (WxH) 2x2, Unit Case Resolution (WxH) of 72x144, Unit Case Dimensions (W x H x D, mm) 500x1000x68, Unit Case Surface Area of 0.50 m2, Weight per Unit Case 12.0 kg, Weight per Square Meter 24 kg/m2, Physical Pixel Density 20736 pixels/m, Flatness of Unit Case ±0.5 mm , Unit Case material of Magnesium, Rear Service access. Optical Specifications- Min. Brightness (After Calibration) of 5000, Color Temperature of 6500, Visual Viewing Angle (Horizontal) 1600, Visual Viewing Angle (Vertical) of 1200, Brightness Uniformity of 97%, Color Uniformity ±0.003CxCy, Contrast Ratio of 5000, Processing Depth 14 bit. Electrical Specifications- Power Consumption (W/Unit, Max.) of 330, Power Consumption (W/Unit, Avg.) of 110, Power Consumption (W/m, Max.) 660, Power Supply (V) 100 to 240, Frame Rate (Hz) of 50 / 60, Refresh Rate (Hz) 3840, Operating Temperature of -10°to +45°, Operating Humidity of 0-80%RH, IP rating Front IP65, IP rating Rear IP54. Controller- Controller Name LCIN006, Loading Capacity 1920*1200@60HZ, Maximum Width: 2560pixels, Max Output Range of Maximum Height: 1200 pixels, Output Resolution of 2.304 Million Pixels, Input Interface HDMI and DVI, Output Ethernet 4-channel, Sensor interface V, Brightness Adjustment V, Chroma Adjustment V, Cascading V, Regulatory Compliance (both for LED Wall and Controller) IEC 60950-1 / EN 60950-1 / UL 60950-1, CE / KC, BIS, RoHS. Video wall controller and screen should be of same make.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 Sqm.

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, totalweight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing in position pre-cast R.C.C.manhole cover and frame of required shape and approved quality 19.19.1 L D- 2.5 Rectangular shape 600x450 mm internal dimensions

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in 20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

50 mm dia. nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing uplasticised PVC connection pipe with brass unions : 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I.brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar tap

(a)Providing and fixing soil, waste and vent pipes:100 mm dia Sand cast iron S&S pipe as per IS: 1729

(b) 75 mm diameter :Sand cast iron S&S pipe as per IS: 1729

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :20 mm dia (heavy type)

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : for 75 mm dia pipe

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 1500x450 mm

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing double equal plain junction of required degree 100x100x100x100mm

75x75x75x75mm

Providing and fixing heel rest sanitary bend Sand cast iron S&S as per IS - 17295 mm diameter pipe Sand cast iron S&S as per IS - 1729 100 mm diameter pipe

75mm dia

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Range of three half stall urinals with 10 litre P.V.C. automatic flushing cistern.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size)as per direction of Engineer-in-charge and finished smooth Granite Stone of approved shade. .

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A Point 717

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required. Each 406

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. Each 401

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. -2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door Each 1661

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A Each 339

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of ollowing poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole.

Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

S/F of Exhaust Fan 230/300mm as approved by E/I ---complete in all respect

S/F of ceiling Fan 1200mm(48") as approved by E/I ---complete in all resepct.

Supplying and fixing of Decorative LED tube light fitting 18W, 4 feet long including tube rod complete with making connection and complete with all respect directed/approved by E/I.

Supply of fixingh of factory eired ISI/ ECRTIFIED LED street light 40-45 W Capacity pressure dia cast or extruded Aluminium housing with corrossion resistant polyster powder coated side entry type shall consist at separate and control gear campatoment thoughened glass energy afficenvy LP- 18 watt operation voltage 140-270 HZ freequency 140-270 V electronic driver with internal surge protection of 4 KV street light should be protected with short circuit open circuit Reverse polarity and automatic safe shut down after 300 V AC and below 100 V A.C as per direction by E/I complete in all respect.

Supply of LED Lamp 15 W 230/250 Volt,50 Hz etc.

Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture 150 mm diameter S.W, pipe

Supplying and fixing M.S Man hole Cover for Collection Tank

Pump Motor : (0.5 HP) Texmo-3 phase 415, 50 Hz, Suction Size 65 mm, Delivery Size 50mm, for 5 m head +Sump

Bio-Digester Tank 6000 Ltr installation, plumbing and delivery at Site

Providing and fixing Smart IT Enabled Bio-Toilet with Ladies toilet with basin +2 Gents Toilet basin and 2 urinals(06 Units)

Plantation of Trees,Shurbs and Hedge at site i/c watering and removal of unserveiceable materials as per direction of officer in charge (excluding cost of plant & water )Hedge Plant

Trees

Opearation and Maintenance for one year

Supervisor

Helper

Gardner

Sweeper

Soap, Brooms, Mpos, Dustpan, Detergent, Phenyal Tool etc (LS)

Water and Electricity Charge (LS)

Security Guard round the clock

Electricion

Plumber

Comprehensive maintenance of drain and existing sewer

Consumble items likes manuare, fertilizers, seasonall flowers, seeds, tool etc.

Civil Works (LS)

Electric Item (LS)

M/s Om Veer Singh