SPECIAL REPAIR TO BLDG No. T-88 (OTM) OF 849 FD WKSP COY EME AT RAIWALA MIL STN.

Amount

Excavating in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation or for shafts, well cesspits, manholes etc / for laying of cable etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed.

Removing excavated material exc 1.5Km but n.exc 5.0 Km and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for post construction anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for Cement concrete ( reinforced) including removal of debris etc to a distance out side MoD land complete all as specified and directed.

M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, and in shelves complete all as specified and directed.

M&L for formwork for rough finish to soffits of suspended slabs such as roof slabs, floor slabs, landing slab and similar work, not exceeding 200mm thick complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete and all as specified and directed.

M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) and set in CM (1:6) including necessary fair finish formwork complete all as specified and directed.

Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with old size full brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for brick work with old size half brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed.

Demolition of concrete (un-reinforced)of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of PCC in ground floor and pavings not exc 15 cm thickness below or above ground level including removal of rubbish out side MOD land complete all as specified and directed.

M&L for PCC (1:4:8) type D2, (40 mm graded stone agg) as in sub base of floor/ hardstanding/ footpath complete all as specified and directed.

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water and removing unseviceable materials out side MoD land complete all as specified and as directed.

M&L for 15mm thick plastering on fair faces of brick wall in CM (1:6) surface finished even and fair complete all as specified and directed.

M&L for 15mm thick plastering on fair faces of brick wall in two layers, Ist layer 10mm thick CM (1:6), and IInd layer 5mm thick CM (1:4), surface finished even and fair mixed with @ 200ml per bag WPC (liquid type) complete all as specified and directed. Note :- WPC (Liquid type) shall be measured and paid separately as supply only.

Supply only WPC integral water proofing compound (Liquid type) complete all as specified and directed.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (walmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge.

M&L for preparation of old decorated surface of exterior wall by complete removal of existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching powder solution for treatment of fungal growth and applying two coats of exterior anti fungal acrylic emulsion paint of required shade (wallmista of Berger paint or equitant in Asian paint, Nerolac etc having three years of performance warranty) over a coat of exterior water based primer of same make all as specified and prescribed by manufacture of point and as directed at site by Engineer-in-Charge.

M&L for preparation of newly plastered surface of interior wall by application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper over a coat of primer using roller all as specified and prescribed by manufacturer of paint/ distemper and as directed at site by Engineer-in-Charge.

M&L for preparation of old decorated surface of interior wall by complete removal of existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers and application of wall care putty to remove the dent and to make the surface even and smooth by grinding or rubbing with sand paper and applying two coats of acrylic distemper using roller all as specified and prescribed by manufacturer of paint and all as directed at site by Engr-in-Charge .

Note for item No. 21 to 24:- (i) The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of emulsion paint. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. (ii) The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE/ AGE (I) before commencement of work. (iii) All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv) after carrying out preparation of surface the same shall be got approved from GE /AGE (I) before application of distemper for each building. (v) The colour / shade will be all as approved by GE / AGE (I). (vi) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor.

S&F in repair 5mm thick beveled edge best quality looking mirror of size 600x450 mm with 30 mm PVC beading all around the glass, mounted over 3mm thick PVC sheet or 6mm thick AC bldg board, complete all as specified and directed.

S&F 150mm in repair of stainless steel peg set of 3 Nos fixed to wooden plank complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed.

Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) of following size complete all as specified and directed:-

Area not exc 1.5 sqm each

Area exc 1.5 sqm but not exc 4 sqm each

M&L for MS fastner of size 200 to 250mm for fixing wooden door frame and like in postion complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable and variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately.

50mm x100mm size

65mm x125mm size

M&L for 30mm thick factory made solid WPC (wood plastic composit) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texteure, including stainless steel wire mesh shall be fixed with 15 x15 mm square tube in side rails with screwing 8 x 28 heat metal zink coated screw can be remove or fix again after changing of wire mesh, when needed. The density of the shall be as per manufacture instruction compete all as specified and directed.

M&L for factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter comprising of virgin polymer of K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws of following thickness complete all as specified and directed :- Note: stainless steel butt hinges and necessary stainless steel screws shall be paid separately.

35mm thick

30mm thick

M&L for factory made 35mm thick 100% solid WPC window glazed shutter and Gauzed (wire mesh) shutter 95 mm x35mm thick. Made from WPC material with density not less than 800 kg/cum. All four corner are fusion welded & screwed with 8 x 50mm self-screws for additional strength. After joining all 4 corner clear space to be paneled with 5mm thick glass / S S mosquito mesh after glazing of inside of shutter 10 x 12mm pvc “L” shape bead to be nailed or sticked with shutter. Provided 2 Nos SS hinges of 100 mm, 1 Nos aluminium handle of 125 mm , 2 Nosaluminium tower bolt of 125mm and 01 peg stay for each shutter (Glazed and Gauzed) incl factory made 100 % solid WPC window frame 125 mm x 65 mm double rebated frame & mullion 125 x 80mm. made from WPC (Single extruded process) material comparising of virgin PVC polymer of K value 57-60 (suspension grade), calcium carbonate and natural fibers (Wood powder/ rice husk/wheat husk) and nontoxic additives fabricated with meter joints after applying PVC solvent cement & screwed with fully body treated star headed screws having minimum frame desity not less than 800 kg /cum, having good screw holding capacity (screw withdrawal strength of (min 990N). Minimum compressive strength of 58 N/mm2. Modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof, water / mosquito proof & fire retardant & fixed in position with fasteners / hold fast of required size. Window shall be provided with MS Grill/Guard Bars made of 10mm MS Sq Bar welded to 6 x 12mm MS Flat including painting with countersunk holes at both vertical ends. Gap between the bars should not be more than 125mm. All as per specification drawing as directed by Engr-in-charge. Note - (i) Glazed and Gauzed shutter both are deemed in this quoted rate (ii) Glass pane, wire mesh and grill are deemed in this quoted rate

M&L for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised (ISI marked) of following size complete all as directed and specified:-

150 mm long

S&F anodised aluminium barrel tower bolts (ISI marked) of extruded section of following size complete all as directed and specified:-

300 mm long

200 mm long

S&F anodised aluminium sliding door bolt (ISI marked) with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of following size complete all as specified and directed:-

300mm long

S&F stainless steel butt hinge (ISI marked) as approved by GE complete all as specified and directed.

S&F in repair plain mild steel GI wire 2.5mm dia, galvanised class 3, fixied with GI pipe along with straining ang necessary fitting in detached work such as for mosquito net and fixing to straing bolts, hooks, eyes etc complete all as specified and directed.

S&F mild steel adjustable hook both side (min 250mm to 300mm), solid body, fixed to walls with suitable fastener for fitment of steel wire hanging lines complete all as specified and directed.

S&F floor door stopper (ISI Marked) of aluminium alloy body and tongue anodised, with hard drawn steel spring, fixed in floor of following size complete all as specified and directed :-

150mm long (overall length of cover plate)

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

S&F stack clamps out of 50mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for following bore of pipe complete all as specified and directed :-

100/ 110mm bore pipe

75mm bore pipe

Dismantling of timber scantling 40 sqcm and over in section, in any position as in framed work complete all as specified and as directed.

M&L for second class hard wood (sal) in timber scantling (wrought) as in framed and fixed complete all as specified and as directed.

M&L for preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote complete all as specified and directed.

M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

Dismantling of wall and ceiling boards ( fibre, pulp insulation etc.) or insulation boards/ slabs/ blankets of any thickness, including cover fillets complete all as specified and directed.

S&F tiled false ceiling of desginer tile (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gsm, both side inclusive and black painted groove on all T webs) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32mm made of 0.30mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 15x32mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20x0.40 mm and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanized Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width,including making good all the disturbed portion with existing surface with necesary arrangemnets of scaffolding at all heights complete all as specified and directed. Note : Cost of making frame work and board (cut out) for fixing light fitting grill diffuser etc shall be deemed included in the quoted rate.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises from MoD land complete all as specified and as directed.

M&L for non skid, joint free, coloured ceramic tiles 7-8mm thick (Square/Rectunglar), as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles laid with and including over 15mm thick screed bed in CM (1:4), area of each tiles shall be of following complete all as specified and directed :-

Area of each tile exc 0.11 Sqm but not exc 0.18 Sqm.

M&L for coloured glazed ceramic tiles of any design and pattern, 300x450x 7 to 8mm thick, as in dado etc incl 10 mm thick rendering in CM (1:3), set and jointed in neat cement slurry and pointed in white of coloured cement to match the shade of the tiles. Tiles shall be confirming to IS-15622:2017, Group B III with average water absorption between 10% to 15%. Length, width and straightness of sides + 0.20% (Max deviation). Thickness + 4.0% (Max deviation). Straightness of sides and Rectangularity +0.15% (Max Deviation). surface flatness + 0.22% (Max deviation). Breaking strength 500 N (Minimum) and minimum 95% tiles shall be free from visible defects complete all as specified and directed. Note: Shade of the tiles including Colour, design and pattern shall be got approved by AGE(I)

M&L for 25 mm thick PCC (1:2:4) type B1 (20 mm graded stone agg) as in sub floor of flooring complete all as specified and directed.

M&L for mirror polished machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing over and including 15mm thick screed bed in cement mortar (1:3) complete all as specified and as directed Note:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced).

Description same all as per Item No. 54 above but, as in riser of steps, skirting etc ( 10-12mm thick Kota stone ) over and including 10mm thick rendering in cement mortar (1:3) complete all as specified and as directed. Note : Only one stone piece on one riser must be use.

M&L for 18-20mm thick pre polished udaipur green stone (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including rubbing and polishing over and including 15mm thick screed bed in cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of stone complete all as specified and as directed.

S&F in repairs for stainless steel non magnetic curtain rod of 25mm dia with and including fixing brackets and decorative type knobs (as approved by AGE (I)/ GE both side of each rod complete all as specified and directed. Note: - Measurement will be taken between end point of knobs.

S&F aluminium door seal upto 1200mm long on bottom of door complete all as specified and directed.

S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approvrd by GE complete all as specified & directed. MAKE: Parryware, Model E8090 SLIMLINE or equivalent model of make as specified in appendix.

S&F in repair vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed.

S&F in repairs Vitreous China wash down water closet pan (Pedestal pattern) incl close seat cover, hinges,fixing accessories and accessories set and cistern with cistern fitting complete, flush pipe incl all joints complete all as specified and directed. Make – Jaquar Cat No-ECS-WHT-851S220NPP or equivalent model of make as specified in appendix.

S&F in repair vitreous china urinal half stall type urinal complete including providing and fixing plugs bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm brass screws pointing around urinal back in cement fixing automatic flushing cistern with brackets flush pipe grating and union for discharge pipe complete all as specified and directed.

S&F brass CP urinal spreader fixing with 15 mmdia pipe complete and all as specified and directed.

S&F rotational moulded polyethylene water storage tank, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, of following capacity of tank complete all as specified and as directed:-

Capacity 2000 Ltrs

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipes or brass ferrule and fixed of following size complete all as specified and as directed :-

20mm bore ( minimum weight 210gms)

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and laid in trenches or in floor of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to wall of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) bends any radius including necessary cutting in brick wall and making good to match with existing surface of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) bends with access door any radius of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) junction single, (single T) equal or unequal of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR) vent cowl of following size complete all as specified and as directed :-

75 mm bore

S&F PVC (SWR) multi floor trap, out let dia 75mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F PVC (SWR) floor trap, out let dia 75mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F PVC (SWR) P trap, out let dia 110mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F PVC (SWR) reducers of size 110 mm x75 mm complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required of following size complete all as specified & directed :-

110mm bore

S&F chromium plated brass tubular towel rail, D type, 60 cm long between flanges complete all as specified and directed. MAKE: Jaguar, Model ACN-1111NM (Continental series) or equivalent model of make as specified in appendix.

S&F in repair chromium plated brass tubular towel ring fixed with CP screws and wood cleats with wall complete all as specified and directed. MAKE: Jaguar, Model AQN-7721 or equivalent model of make as specified in appendix.

S&F in repair Glass shelf with Sheet Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long.complete all as specified and directed. MAKE: Jaguar, Model ACN-1171N or equivalent of other make as specified in appendix.

S&F in repair sheet glass cornor self of 3 tier assembly consisting of 5.5mm thick sheet glass self 15cm radius with chromium plated bracket guard and rail and fixed with CP screws and wood cleats with wall complete all as specified and directed.

S&F gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, for following bore complete all as specified and directed:-

20 mm bore

S&F in repairs 15mm bore Stop valves (angular stop cock), cast copper alloy, fancy type, chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle or concealed screwed both ends for iron pipe or for unions complete all as specified and directed. Note for all CP item :- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

S&F in repair 15mm bore stop angle valve, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed.

S&F 15 mm dia bore bib taps, long body, cast copper alloy with fancy type, chromium plated capstan head long body with wall flange, screwed for iron pipe, or for brass ferrule complete all as specified and as directed. Make : JAQUAR, Cat Part No. CON-107KN or equivalent make as specified.

S&F in repair wall mixer with with connector for hand shower arrangement with connecting legs, wall flanges and wall bracket for hand shower and shower arm chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm bore pipes complete all as specified and directed. Make : JAQUAR, Cat Part No. CON-267KN or equivalent of other make as specified.

S&F in repair 15 mm dia brass chromium plated central hole wash basin mixture, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut capstanhead screwed for 15mm dia pipe complete all as specified and directed. MAKE: Jaguar, Model CON-169KNB (Continental series) or equivalent other make as specified in appendix.

S&F in repairs Chromium plated shower rose 120 mm size with or without swivel joints, any size, including fixing to 15mm GI pipe or union complete all as specified and directed. Make : JAQUAR, Cat Part No. OHS-1789 or equivalent of other make as specified.

Supply only PVC connection 15 mm size with PTMT nut of following length complete all as specified and directed :-

S&F in repair vitreous china oval shape counter top wash hand basin, coloured, flat back, size 570 x 450mm excluding taps, waste pipe & waste coupling complete all as specified and directed. MAKE: Cera, Model - COMET 1016 or equivalent model of make as specified in appendix. Note : Rate quoted under this item deemed included fixing of taps, waste fittings and union, plug and chain and connecting up to supply pipes, wastes or traps etc.

S&F in repair 127mm dia round grating chromium plated complete all as specified and directed.

S&F in repair stainless steel jet spray suitable for europian western commode (EWC) including 1.5m length braided tube with PTMT nut and washer complete all as specified and directed.

M&L for chequered cement concrete tiles, ISI Marked, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 15mm thick screed bed in cement mortar (1:4) for following size of tile complete all as specified and as directed:-

30cm x 30cm x 25mm thick

S&F in repair soap dish recessed type (stainless steel) fixed with CP screws and wood cleats with wall complete all as specified and directed. MAKE: Jaguar, ESSCO Model AEC-1131N or equivalent model of make as specified in appendix.

Taking up or down steel water tubing (GI Pipe) and connections of following bore complete all as specified and as directed :-

15mm bore

20mm bore

S&F galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling of following bore complete all as specified and as directed :-

15mm bore

20mm bore

Refixing old galvanised steel water tubing, with all new fittings (ISI Marked) and fixed to wall, floor and ceiling of following bore complete all as specified and as directed :-

20mm bore

M&L for cutting chases in brick wall, pinning in and making good in cement mortar (1:3) to match with existing surface for following girth complete all as specified and as directed :-

Cutting not exc 10cm girth.

S&F low density polythene pipe (LDPE) of pressure rating 6 Kgf / sqcm fixed to wall or laid in floor etc including fittings of following size complete all as specified and as directed :-

32 mm bore

Demolition and breaking up drain pipes (PVC/ SGSW/ AC/ RCC pipe) of following bore of pipe, set in cement mortar complete all as specified and as directed:-

100mm bore

M&L concrete bed to pipes in PCC (1:4:8) type D2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid on slope and tested for following bore sewer pipe line complete all as specified and directed :-

100mm bore

M&L for salt glazed stone ware (SGSW) pipe, grade A, ISI marked, laid in trenches and jointed in CM (1:1) for following bore of pipe complete all as specified and directed :-

100mm bore

M&L for writing letters or figures (Block, Roman, Italic or Indian) not exc 30cm high complete all as specified and as directed.

M&L for cutting of bushes small trees (Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas , wall junction parapet etc at any height by necessary demoliton of brick work etc if requried and making good distrubed surfaces to match with existing finihes with and including in CM (1:4) mixed with WPC /PCC (1:3:6) type B0 /Bk work in CM (1:4) as required at site and as directed by Engr-in-Charge.

Dismantling and taking down old unserviceable point wiring of any type (light, fan, socket, power etc) complete with fitting such as switches, sockets, ceiling roses, pendants, lamp holders, light fitting etc including CI/ pressed steel terminals, switch box and making good the disturbed surface of wall/ floor etc to match with the existing surfaces of wall/ floor complete all as specified and directed. Note :- (i) If the contractor fail to make good the disturbed surface of wall/ floor etc and do not match with the existing surface of wall/ floor to the entire satisfaction of Engr-in-Charge, a recovery of @ Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute, the decision of Accepting Officer will be final and binding. (ii) Old fittings/ fixtures / accessories like switches, sockets, lamp holders, regulators etc., if found in serviceable condition shall be removed carefully for reuse in the work or taking on charge. (iii) Only old unserviceable items will be considered in credit Sch.

M&L for point wiring with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 Sqmm multi stranded copper conductor cable (FRLSH) with continious earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed, drawn in and including concealed PVC conduit "medium grade" (ISI marked), not less than 20mm dia duly concealed on wall/ ceiling or above false ceiling with fittings medium grade (Color coding of wires shall be phase, neutral and earth wire all as specified) sunk metal flush box suitable for modular fixture with and including decorative polycarbonate frame for housing modular switches, sockets, fan regulators etc including white cover plate complete all as specified and directed for following:- Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface in CM (1:3) and matching with the existing surface deemed included in quoted rates. (ii) If the contractor fail to make good the disturbed surface of wall/ ceiling etc and do not match with the existing surface of wall/ceiling to the entire satisfaction of Engr-in-Charge a recovery of @ Rs. 50/- per RM will be made from payment due to the contractor. In case of any dispute the decision of Accepting Officer will be final and binding.

One light/fan/exhaust fan/call bell point controlled by one way 5 Amp switch.

One 5 pin socket out let 5/6 Amp on independent board.

One 5 pin socket out let 5/6 Amp on same board.

Descrition same all as per item No 105 above, but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point complete all as specified & directed.

S&F modular switch piano, 1module, flush type button 5/6 Amp single pole one way conforming to IS: 3854 and ISI marked complete all as specified and directed. Make: Legrand cat No: 6734 01 or equivalent of make as specified.

S&F modular switch piano, 1module, flush type button 15/16 Amp single pole one way conforming to IS: 3854 and ISI marked complete all as specified and directed. Make: Legrand cat No: 6734 11 or equivalent of make as specified.

S&F modular socket outlet, 2 module, five pin 2 in 1, 5 Amps, flush type, 230 volts AC circuit complete all as specified and directed. Make: Legrand cat No: 6734 52 or equivalent of make as specified.

S&F modular socket outlet, 2 module, five pin 2 in1, 15 Amps, flush type, 230 volts AC circuit complete all as specified and directed. Make: Legrand cat No: 6734 55 or equivalent of make as specified.

S&F modular fan regulator electronic, 2module, stepped type, suitable for ceiling fans of any capacity, pre-wired 120/ 280 volts AC 50Hz supply 100Watt complete all as specified and directed. Make: Legrand cat No: 6734 30 or equivalent others make as specified.

S&F ceiling rose surface bakelite 65 x 25mm dia three terminals (ISI Marked) complete all as specified and directed. Make – Anchor Jumbo Code-39050 / 3224 or equivalent of make as specified.

S&F angle Lamp holder (with metal ring), insulated body, of PVC/ Polycorbonate with back plate (ISI Marked) suitable for batten fitting complete all as specified and as directed. Make– Anchor, Code-39797 or equivalent others make as specified.

Dismantling and taking down u/s sub-main wiring/service wire of any size including wooden batten / PVC Conduit etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc complete all as specified and as directed. Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

S&F sub main wiring alongwith earth wire (green colour) with single core FRLSH, PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (medium grade) with standard accessories and earth wire connected with main earth dolly, of the following sizes of cable & dia of conduit complete all as specified and directed:- NOTE :- (i) Two/four run of single core FRLSH PVC cable with one/two run of earth conductor and conduit shall be measured as one unit (RM). (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc of any description for concealing the conduits to required depth & making good the disturbed surface in CM (1:3) including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using PVC rawal plugs.

2x4 Sqmm + 1x4 Sqmm earth wire with PVC conduit 20mm dia or more

S&F surface mounted LED luminiare, 20 watt with all accessories having polymer extruded channel with diffuser for glare free light, high lumen output, driver PF >0.98 having over voltage protection upto 400 volts surge protection, level 7-10 KV thermal short circuit protection THD<10%, made up of long life LED chips (SMD) in modular with Ra>70 and lumen efficiency >120 lumen per watt, internally pre-wired through flexible wire connecting with ceiling rose complete all as specified and directed. Make :- Crompton, Cat No LCTLN-20-CDL / Havells, Cat No LHEXACP7FN1W020 or equivalent of make as specified. Note: The firm has to give warranty for fitting including driver minimum for 2 years for any defects developed during the period.

S&F LED building security light 1 x 20 W housing made out of pressure die-cast aluminium alloy with toughned glass, IP 66 protection working on 240 volts, 50 Hz, consisting of reflecting lamps wired with appropriate driver PF> 0.98 having overvoltage protection upto 440 volt, surge protection level > 10 KV, thermal short circuit prtection THD< 10% made up of long life LED chip (SMD) in modular with Ra< 70, and LED lumen efficiency > 140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive wway, 80 degree luminaire efficiciency> 120 luminous /watt power LED should be of more than 01 watt CCT should be between 5700° K- 6500 K including fixing on existing bracket including connecting with 1.5 sqmm , 3 core, PVC insulated copper onductor cable 1100 Volt grade from distribution box to light complete all as specified and directed. Make :- Havells Cat No: LHEXAYP7PN6K020 / Crompton Cat No:TRP-400-20-57-LM-NSR or equivalent of make as specified. Note :- (i) The firm has to given warranty of street light fittings including driver minimum for 03 years for any defect developed during the period. (ii) The contractor Shall submitt the third Party LM 79 report from any NABL approved laboratory. (iii) The fiitting should have BIS , CRS No(iv) Connection to luminaire shall be done in suitable PVC connector within the bracket/luminaire end and are inclusive in above.

Supplying, laying, commisioning and testing of 1.1 KV grade XLPE insulated, PVC sheathed, steel armoured, aluminum stranded conductor LT UG cable (Conforming to IS 7098), ISI marked, in trenches / ducts / through GI pipes under roads of following size complete all as specified and directed:- Note:- 1. The earth work, GI pipe shall be measured and paid sepretely. 2. Cable may fixing/ passing through pipe laid in trenches or fixed to pole/ wall or fixed to LT panel etc.

16 Sqmm, 4 core.

Excavating in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation or for shafts, well cesspits, manholes etc / for laying of cable/ pipe etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Removal of surplus soil to a distance n'exc. 50 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for sand cushioning with dry and clean fine river sand for underground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified and directed. Note:- Punned thickness shall be considered for payment purpose.

Supply and laying cable protection bricks, common burnt clay sub class 'B' designation 75 for protection of UG cable laid in trenches with axis of the bricks perpendicular to the axis of the cable complete all as specified and directed.

M&L for road cutting of size n'exc 20cm width and n'exc 90cm depth for laying of cable including making good the road with PCC (1:3:6) type C2 complete all as specified and directed.

S&F galvanized steel water tubing (GI Pipe) light grade (ISI marked) with all fittings as in sleeving for cable protection & laid in trenches/ floor or fixed to wall, ceiling and pole of following bore complete as specified and directed :- Note : MS Clamp, nut bolts and washer shall be measured and paid seperatly for fixing with pole etc.

50mm bore

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground, earth pit not less than 2.25 mtr depth below ground level at any type of strata with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate, connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC (1:3:6) type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM (1:4) funnel with wire mesh, RCC pit cover of 320 x 320 x 80mm size PCC (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick reinforced with XPM weighing not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

Disconnecting and taking out old damaged existing main switch/ distribution board of MCB/MCCB of any description from wall with and including all fitting and fixture and making good to disturbed surface of wall/ floor to match with the existing wall/ floor etc complete all as specified & as directed. Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/ floor to the entire satisfaction of Engr-in-Charge, a recovery of @ Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of Accepting Officer will be final and binding.

S&F connecting & testing distribution board of sheet metal enclosures double door, IP-43, 240V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps rating having following capacity complete all as specified and directed:-

DB SPN, 8 way Make :-Legrand Cat Part No- 5076 11 or equivalent others make as specified.

S&F connecting & testing distribution board of sheet metal enclosures double door, IP-43, 415V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps rating having following capacity complete all as specified and directed:-

DB TPN, 4 way Make : Legrand Cat Part No. 5076 70 or equivalent others make as specified.

S&F connecting & testing MCB, 230V/ 415V with rupturing capacity 10 KA of following capacity complete all as specified and directed:-

MCB 6 to 32 Amp, SP, 'B' series/ curve, Make :- Legrand, Cat Part No 4024 31 to 4024 36 or equivalent others make as specified.

MCB 6 to 32 Amp, SPN, 'C' series/ curve, Make :- Legrand, Cat Part No 4086 09, 4086 12, 4086 14 to 4086 17 or equivalent others make as specified.

MCB 6 to 32Amp, TP, 'B' series/ curve, Make :- Legrand, Cat Part No 4024 49 to 4024 54 or equivalent others make as specified.

S&F air fresh fan AC single phase 230/240 Volt of size 300mm sweep, metallic body powder coated painted finish, power consumption 50W, air displacement 1290 Cum/Hr, RPM-1200 complete with louvers including making whole and grouting of nut bolts etc and making good the disturbed surfaces of wall to match with existing complete all as specified and directed. Note : Core cutting of existing wall (Brick/ stone) for fixing of fresh air fan and making good as directed deemed to be included in quoted rate.

AKANSHA.ASSOCIATES

AMARJEET SINGH AND CO.

Sunil Enterprises

RAMAPATI ENGINEERING SERVICES

TARUN ENGINEERING WORKS

shreyansh construction