Development of Play Ground at T.P. Scheme No. 55 (Bhestan), F.P. No. 39, Open plot in South Zone-A (Udhna), Surat.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Boring holes 3.5 mt.deep in ordinary soil (for cast in

situ piles) & disposal of the surplus excavated soil as

directed within a lead of 50 M. For following diameter of

Excavation for foundation includ.sorting out &

stacking of useful materials & disposing of the

excavated stuff upto 50 mt. Lead & all lift, watering

etc. Comp. (A) Loose or Soft soil With Machinaries

Providing & laying cement concrete 1:4:8 (1 cement: 4 sand

3 :8 graded stone agg. 40 mm nominal size) & curing comp. 0.00 2,769.69 C.M. -

excl.cost of form work in (A) Foundation and Plinth

Providing & laying cement concrete 1:2:4(1 cement:2

sand:4 graded stone agg. 20 mm nominal size)& curing

4 comp. Includ.cost of form work but exclu. Cost of 0.00 3,741.69 C.M. -

reinforcement for reinforced concrete work in : (A)

foundation, footing, base of columns and mass concrete

Providing & laying ordinary cement con.1:2:4

(1cement:2sand:4graded graded stone agg. 20 mm nominal

size) finishing smooth curing etc. comp. Incld. Cost of form

work but excl. Cost of reinforcement for R.C.C. Work in :

(1) Having c/s area up to 0.08 s.mt. 0.00 12,335.51 C.M. -

(2) Having C/S area more than 0.08 sq.mtr. & up to

(2) Having C/S area more than 0.08 sq.mtr. & up to

Filling available excavated earth (excluding rock) in

trenches plinth, sides of foundations etc. in layer not

exceeding 20cm in depth consolidating each deposited layer

by ramming & watering.

Providing & laying C.C 1:3:6 (1cement :3 coarse sand :6

7 crushed stone agg. 20 m.m Nominal size)& curing comp. 17.00 4,085.83 C.M.

incl. cost of from work in: wall caps/ copings.

Providing & fixing IS Mark TMT Bar FE 500 / FE 500D

8 reinforcement for R.C.C. work incl. bending, binding & 1105.00 77.29 Kg

placing in position etc. comp. Upto G.L./P.L.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Brick work using common bunt clay buliding bricks having

9 crushing strength not less than 35 Kg./sq.cm. in C.M. 1:6 297.00 4,729.83 C.M.

(1 cement:6 fine sand ) (c) Fly Ash Bricks - Ground Floor

Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:4 (1- Cement : 4 - coarse sand ) in

foundation and plinth (C)Fly Ash Bricks

20mm thick sand faced cement plaster on walls upto height

10 metres above ground level consisting of 12mm thick

11 backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm 2542.00 347.42 S.M.

thick finishing coat of C.M. 1:1 (1-cement : 1- sand) etc.

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

12 specification and directions in shade and colour approved 2542.00 82.00 S.M.

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Surface preparation:

Steel work welded in built up sections, framed work

including cutting, hoisting, fixing in position and applying a

priming coat of red lead paint

13 (A) in beams & joists channels angles, tees, flats with 0.00 91.08 K.G. -

connection plates or angle cleats as in main & cross

beams,hip & trussed purlins connected to common raffers

Applying Priming coat over new steel and other metal

surface after over and including preparing the surface by

throughly cleaning oil, grease dirt and other foreign matter

and scoured with brushed fine steel wool, scrapers and sand

paper with ready mixed priming paint brushing red lead.

Painting two coat (excluding priming coat) on new steel and

other metal surface with synthetic enemal paint, burshing to

give an even shade including leaning the surface of all dirt,

dust and other foreign matters.

Vollyball Court

Preparation of subgrade with Compacting, Levelling and

consolidation of subgrade with miniroller /Plate vibrator

16 machine including watering and filling in depressions 912.00 9.00 S.M.

which occur during the process as directed by engineer in

Providing & filling with Mix soil in layers of 20 cm. Th'.

Incl. watering,ramming & consolidation etc. complete

Supplying & filling fine sand (pana) in

mm/100mm/150mm compacted thickness over the base

18 including necessary compaction, watering etc. complete. 183.00 1,016.00 C.M.

Item includes leveling by using vibratory plates compacted

machine and as directed by engineer in charge.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Boring holes 3.5 mt.deep in ordinary soil (for cast in

situ piles) & disposal of the surplus excavated soil as

directed within a lead of 50 M. For following diameter of

For 250 mm Dia. 6.00 334.80 R.M.

Providing & laying cement concrete 1:2:4(1 cement:2

sand:4 graded stone agg. 20 mm nominal size)& curing

20 comp. Includ.cost of form work but exclu. Cost of 1.00 3,741.69 C.M.

reinforcement for reinforced concrete work in : (A)

foundation, footing, base of columns and mass concrete

Providing 100mm thick readymade C.C. kerb of strength M-

20 (size 300mm x 380mm) purchased from SMC's

approved paverblock manufacturer & setting in line, level

and in truly vertical position, including filling joints in C.M.

1:1 (1 part of cement : 1 part of stone dust) smooth pointing

in C.M. 1:1 (1 part of cement : 1 part of coarse sand)

including watering etc. complete and as directed by

engineer in charge.

Steel work welded in built up sections, framed work

including cutting,hoisting, fixing in position and applying a

priming coat of red lead paint

22 (A) in beams & joists channels angles, tees, flats with

connection plates or angle cleats as in main & cross

beams,hip & trussed purlins connected tocommon raffers &

Applying Priming coat over new steel and other metal

surface after over and including preparing the surface by

23 throughly cleaning oil, grease dirt and other foreign matter 4.00 36.74 S.M.

and scoured with brushed fine steel wool, crapers and sand

paper with ready mixed priming paint brushing red lead.

Painting two coat (excluding priming coat) on new steel and

other metal surface with synthetic enemal paint, burshing to

give an even shade including leaning the surface of all dirt,

dust and other foreign matters.

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

25 specification and directions in shade and colour approved 62.00 82.00 S.M.

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Badminton Court

Preparation of subgrade with Compacting, Levelling and

consolidation of subgrade with miniroller /Plate vibrator

26 machine including watering and filling in depressions 820.00 9.00 S.M.

which occur during the process as directed by engineer in

Providing & filling with Mix soil in layers of 20 cm. Th'.

Incl. watering,ramming & consolidation etc. complete

Boring holes 3.5 mt.deep in ordinary soil (for cast in

situ piles) & disposal of the surplus excavated soil as

directed within a lead of 50 M. For following diameter of

For 250 mm Dia. 20.00 334.80 R.M.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & laying cement concrete 1:2:4 (1 cement:2

sand:4 graded stone agg. 20 mm nominal size) & curing

29 comp. Includ.cost of form work but exclu. Cost of 1.00 3,741.69 C.M.

reinforcement for reinforced concrete work in : (A)

foundation, footing, base of columns and mass concrete

Providing 100mm thick readymade C.C. kerb of strength M-

20 (size 300mm x 380mm) purchased from SMC's

approved paverblock manufacturer & setting in line, level

and in truly vertical position, including filling joints in C.M.

1:1 (1 part of cement : 1 part of stone dust) smooth pointing

in C.M. 1:1 (1 part of cement : 1 part of coarse sand)

including watering etc. complete and as directed by

engineer in charge.

Providing & laying Granular sub base (GSB) confirming to

Grading-V of Table 400.0 of compacted thick of 150mm

with specified graded stone metal and sand mixed in place

and laid with mechanical means spreading with motor

grader and compacting with vibratory roller having

minimum 80-100 KN static weight to acheve desired

density of 98% of MDD including all material, labour,

machinery with all leads and lift etc. complete.

Providing & laying cement concrete Pavement using 1:1.5:3

(1 cement:1.5sand:3 graded stone agg. 20 mm nominal size)

& Vaccuum Dewatering technique including floating

surface with a skim powder floater, curing etc.complete.

Providing and laying 200 micron plastic sheet on prepared

sub base For V.D.S Concrete

Cutting of Groove 5 to 7 mm thick in VDS for depth 1/3 of

34 total thickness with filling of epoxy sealent as directed by 406.00 50.00 R.M

engineer in charge

Providing & fixing IS Mark TMT Bar FE 500D

35 reinforcement for R.C.C. workincl. bending, binding & 2500.00 77.29 KG

placing in position etc. comp. Upto G.L./P.L

Steel work welded in built up sections, framed work

36 including cutting,hoisting, fixing in position and applying a

priming coat of red lead paint

(A) in beams & joists channels angles, tees, flats with

connection plates orangle cleats as in main & cross

beams,hip & trussed purlins connected tocommon raffers &

Applying Priming coat over new steel and other metal

surface after over and including preparing the surface by

37 throughly cleaning oil, grease dirt and other foreign matter 7.00 36.74 S.M

and scoured with brushed fine steel wool, scrapers and sand

paper with ready mixed priming paint brushing red lead.

Painting two coat (excluding priming coat) on new steel and

other metal surface with synthetic enemal paint, burshing to

give an even shade including leaning the surface of all dirt,

dust and other foreign matters.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

39 specification and directions in shade and colour approved 60.00 82.00 S.M.

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Providing and applying 2.50 mm thick hot applied

thermoplastic road marking of white / yellow color on

bituminous / concrete surface with fully automatic

machines as per detailed drawings / engineers instructions

for Lane markings, edge markings / arrows including

materials, labour charges, tests required to be carried out

etc. complete as per details in tender specification & as

directed by engineer in charge.

Bump patta/Zebra Patta/Lane/center Line/Edge line 51.00 367.72 S.M.

Preparation of subgrade with Compacting, Levelling and

consolidation of subgrade with miniroller /Plate vibrator

41 machine including watering and filling in depressions 4900.00 9.00 S.M.

which occur during the process as directed by engineer in

Providing & filling with Mix soil in layers of 20 cm. Th'.

Incl. watering,ramming & consolidation etc. complete

Providing 100mm thick readymade C.C. kerb of strength M-

20 (size 300mm x 380mm) purchased from SMC's

approved paverblock manufacturer & setting in line, level

and in truly vertical position, including filling joints in C.M.

1:1 (1 part of cement : 1 part of stone dust) smooth pointing

in C.M. 1:1 (1 part of cement : 1 part of coarse sand)

including watering etc. complete and as directed by

engineer in charge.

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

44 specification and directions in shade and colour approved 280.00 82.00 S.M.

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

LAWN preparation:

: Area cleaning and side grading, removing

unwanted materials, plants, chrubs,wild grass,

weeds,debris,rubbish,etc. Excavating up to depth 30 C.M

surface dressing leveling, making slopes for drainage

according to landscape, Disposal of unwanted materials

with all labour and tools. Development of lawn including

preparation of bed ground, spreading and mixing the good

45 soil with Farm Yard Manure, Gypsum, fertilizer soil with 266.00 90.00 S.M.

farm Yard Manure, Gypsum, Fertilizer bas required hand

specified. Planting of lawn grass bits roots of approved

quality, watering and specified. Planting of lawn grass bits

roots of approved quality, watering, and specified. Planting

of lawn grass watering mowing, weeding etc. maintenance

of developed lawn for a period of 6 months.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Children's Play Ground

Boring holes 3.5 mt.deep in ordinary soil (for cast in

situ piles) & disposal of the surplus excavated soil as

directed within a lead of 50 M. For following diameter of

Excavation for foundation includ.sorting out &

stacking of useful materials & disposing of the

excavated stuff upto 50 mt. Lead & all lift, watering

etc. Comp. (A) Loose or Soft soil With Machinaries

Up to 1.5 Mt. Depth 18.00 123.13 C.M

Preparation of subgrade with Compacting, Levelling and

consolidation of subgrade with miniroller /plate vibrator

48 machine including watering and filling in depressions 1150.00 9.00 S.M.

which occur during the process as directed by engineer in

Providing & filling with Mix soil in layers of 20 cm. Th'.

Incl. watering,ramming & consolidation etc. complete

Providing Suppling & Sprading of Gravel in Play area

including dressing etc.comp.

Providing and laying cement concrete 1:5:10 (1- Cement : 5-

Coarse sand :10- hand broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

Providing & laying cement concrete 1:2:4 (1 cement:2

sand:4 graded stone agg. 20 mm nominal size)& curing

52 comp. Includ.cost of form work but exclu. Cost of 6.00 3,741.69 C.M.

reinforcement for reinforced concrete work in : (A)

foundation, footing, base of columns and mass concrete

Providing & laying ordinary cement con.1:2:4

(1cement:2sand:4graded graded stone agg. 20 mm nominal

53 size) finishing smooth curing etc. comp. Incld. Cost of form

work but excl. Cost of reinforcement for R.C.C. Work in :

(2) having C/S area more than 0.08 sq.mtr. & up to

(2) having C/S area more than 0.08 sq.mtr. & up to

Providing & fixing IS Mark TMT Bar FE 500 / FE 500D

54 reinforcement for R.C.C. work incl. bending, binding & 300.00 77.29 K.G.

placing in position etc. comp. Upto G.L./P.L.

Brick work using common bunt clay buliding bricks having

55 crushing strength not less than 35 Kg./sq.cm. in C.M. 1:6 9.00 4,729.83 CM.

(1 cement:6 fine sand ) (c) Fly Ash Bricks - Ground Floor

Providing & Applying 15mm.th.cement plaster in single

coat on brick/ concrete walls similar surfaces for

plastering & finished even & smooth with a floating

56 coat of cement slurry mixed with admixture of lime or 136.00 249.39 S.M.

neeru in required proportion etc. comp. in C.M 1:3 (1

cement : 3sand)

(A) For wall and similar surfaces -- Ground Floor

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & laying granite slab 18mm thick in flooring,

treads of steps and landing laid on bed of 20mm thick

57 cement mortar 1:6 (1 Cement : 6 coarse sand) or lime 22.00 2,410.00 S.M.

mortar 1:1.5 laid and finished with flush pointing in white

or colour cement including rubbing and polishing complete.

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

58 specification and directions in shade and colour approved 136.00 82.00 S.M.

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Surface preparation: Amount E

Cycle Parking/Walk Way

Preparation of subgrade with Compacting, Levelling and

consolidation of subgrade with miniroller /plate vibrator

59 machine including watering and filling in depressions 1785.00 9.00 S.M.

which occur during the process as directed by engineer in

Providing & filling with Mix soil in layers of 20 cm. Th'.

Incl. watering,ramming & consolidation etc. complete

Supplying & filling fine sand (pana) in

mm/100mm/150mm compacted thickness over the base

61 including necessary compaction, watering etc. complete. 134.00 1,016.00 C.M.

Item includes leveling by using vibratory plates compacted

machine and as directed by engineer in charge.

Providing and laying cement concrete 1:5:10 (1- Cement : 5-

Coarse sand :10- hand broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

Providing 100mm thick readymade C.C. kerb of strength M-

20 (size 300mm x 380mm) purchased from SMC's

approved paverblock manufacturer & setting in line, level

and in truly vertical position, including filling joints in C.M.

1:1 (1 part of cement : 1 part of stone dust) smooth pointing

in C.M. 1:1 (1 part of cement : 1 part of coarse sand)

including watering etc. complete and as directed by

engineer in charge.

Providing interlocking type Rubber moulded cement

concrete paver block of approved shape, design & colour

having 60mm thickness (M-35) purchased from SMC's

approved paverblock manufacturer only & fixing of fine

64 sand bedding. Item includes levelling by using vibratory 1785.00 524.00 S.M.

plates compacted machine. Item also includes all materials,

labour, equipments, tools, plants, watering, cleaning etc.

Providing & laying Granular sub base (GSB) confirming to

Grading-V of Table 400.0 of compacted thick of 150mm

with specified graded stone metal and sand mixed in place

and laid with mechanical means spreading with motor

grader and compacting with vibratory roller having

minimum 80-100 KN static weight to acheve desired

density of 98% of MDD including all material, labour,

machinery with all leads and lift etc. complete.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

66 specification and directions in shade and colour approved 1020.00 82.00 S.M.

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Two Wheeler & Four Wheeler Parking

Preparation of subgrade with Compacting, Levelling and

consolidation of subgrade with miniroller /plate vibrator

67 machine including watering and filling in depressions 1815.00 9.00 S.M.

which occur during the process as directed by engineer in

Providing & filling with Mix soil in layers of 20 cm. Th'.

Incl. watering,ramming & consolidation etc. complete

Providing and laying cement concrete 1:5:10 (1- Cement : 5-

Coarse sand :10- hand broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

Providing 100mm thick readymade C.C. kerb of strength M-

20 (size 300mm x 380mm) purchased from SMC's

approved paverblock manufacturer & setting in line, level

and in truly vertical position, including filling joints in C.M.

1:1 (1 part of cement : 1 part of stone dust) smooth pointing

in C.M. 1:1 (1 part of cement : 1 part of coarse sand)

including watering etc. complete and as directed by

engineer in charge.

Providing & laying Granular sub base (GSB) confirming to

Grading-V of Table 400.0 of compacted thick of 150mm

with specified graded stone metal and sand mixed in place

and laid with mechanical means spreading with motor

grader and compacting with vibratory roller having

minimum 80-100 KN static weight to acheve desired

density of 98% of MDD including all material, labour,

machinery with all leads and lift etc. complete.

Providing & laying cement concrete Pavement using 1:1.5:3

(1 cement:1.5sand:3 graded stone agg. 20 mm nominal size)

& Vaccuum Dewatering technique including floating

surface with a skim powder floater, curing etc. complete.

Providing and laying 200 micron plastic sheet on prepared

sub base For V.D.S Concrete

Cutting of Groove 5 to 7 mm thick in VDS for depth 1/3 of

74 total thickness with filling of epoxy sealent as directed by 50.00 50.00 R.M

engineer in charge

Providing & fixing IS Mark TMT Bar FE 500D

75 reinforcement for R.C.C. workincl. bending, binding & 1000.00 77.29 KG

placing in position etc. comp. Upto G.L./P.L

Providing interlocking type Rubber moulded cement

concrete paver block of approved shape, design & colour

having 60mm thickness (M-35) purchased from SMC's

approved paverblock manufacturer only & fixing of fine

sand bedding. Item includes levelling by using vibratory

plates compacted machine. Item also includes all materials,

labour, equipments, tools, plants, watering, cleaning etc.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing and applying 2.50 mm thick hot applied

thermoplastic road marking of white / yellow color on

bituminous / concrete surface with fully automatic

machines as per detailed drawings / engineers instructions

for Lane markings, edge markings / arrows including

materials, labour charges, tests required to be carried out

etc. complete as per details in tender specification & as

directed by engineer in charge.

Excavation for foundation including sorting out and

stacking of useful materials and disposing of the excavated

stuff up to 50 mt. lead and all lift, watering etc.comp.

(A) loose or soft soil with machineries

Providing and laying cement concrete 1:4:8 (1 cement :

79 sand : 8 graded stone aggregates 40 nominal size) and

curing complete including cost of form work in :

(A) Foundation and plinth 2.00 2,769.69 C.M.

Providing and laying ordinary cement concrete work

1:1.5:3 ( 1 cement, 1.5 sand, 3 graded stone aggregates

80 mm nominal size ) & curing comp.including cost of form

work but excluding cost of reinforcement for reinforced

concrete work in:

(A) Foundation, footing, Base of columns and Mass

Providing and laying ordinary cement concrete 1:1.5:3 (

cement, 1.5 sand, 3 graded stone aggregates 20 mm nominal

size ) finishing smooth curing etc. complete including cost

of form work but excluding cost of reinforcement for

81 R.C.C. work in: Up to G.L./P.L.

(1) Having c/s area up to 0.08 s.mt 1.00 12,844.32 C.M.

(B) BEAM:(G.B/P.B)

(1) Having c/s area up to 0.08 sq. mt. 1.00 9,102.61 C.M.

Providing & fixing IS Mark TMT Bar FE 500D

82 reinforcement for R.C.C. work incl. bending, binding & 410.00 77.29 K.G.

placing in position etc. comp. Upto G.L./P.L.

Brick work using common bunt clay buliding bricks having

83 crushing strength not less than 35 Kg./sq.cm. in C.M. 1:6 1.00 4,729.83 C.M.

(1 cement:6 fine sand ) (c) Fly Ash Bricks - Ground Floor

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each disposited

layer by ramming and watering

Filling in foundation and plinth with murrum or selected

85 soil in layers of 20cm.thickness including watering, 3.00 301.78 C.M.

ramming and consolidating etc. complete.

Providing & Applying 20mm. Th. Heavy Roller plaster on

walls or similar surfaces at all floor levels consisting of

mm av. Th. Backing coat of C.M. 1:3 (1 cement:3 sand) &

8 mm. th. Finishing coat of C.M. 1:1 (1 cement: 1 sand)

apply thick cement slurry and apply roller horizontal as well

as vartical ( two times ) up to good quality and size of grain

in elevation as per directed by engineer incharge.--- Upto

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

87 specification and directions in shade and colour approved 15.00 82.00 S.M.

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Surface preparation:

Work Above Plinth

Providing & laying ordinary cement con.1:1.5:3

(1cement:1.5sand: 3 graded stone agg. 20 mm nominal size)

finishing smooth curing etc. comp. Incld.Cost of form work

but excl. Cost of reinforcement for R.C.C. Work in :

(1)Having c/s area up to 0.08 s.mt- Ground Floor 1.00 12,844.32 C.M.

(1)Having c/s area up to 0.08 s.mt- Ground Floor 1.00 9,102.61 C.M.

(3) Slabs having more than 10 cm. and upto 13 cm.

Providing & fixing IS Mark TMT Bar FE 500D

89 reinforcement for R.C.C. work incl. bending, binding & 690.00 77.29 K.G.

placing in position etc. comp.-Ground Floor

Brick work using common bunt clay buliding bricks having

90 crushing strength not less than 35 Kg./sq.cm. in C.M. 1:6 7.00 4,729.83 C.M.

(1 cement:6 fine sand ) (c) Fly Ash Bricks - Ground Floor

Providing & Applying 10mm.th.cement plaster in single

coat on brick/concrete walls similar surfaces for plastering

& finished even & smooth with a floating coat of cement

slurry mixed with admixture of lime or neeru in required

proportion etc. comp. in C.M 1:3 (1 cement : 3sand) (A)

For wall and similar surfaces - Ground Floor

(A) For wall 38.00 199.28 S.M.

(B) For ceilings and soffits of stairs 10.00 225.34 S.M.

Providing & Applying 20mm. Th. Heavy Roller plaster on

walls or similar surfaces at all floor levels consisting of

mm av. Th. Backing coat of C.M. 1:3 (1 cement:3 sand) &

8 mm. th. Finishing coat of C.M. 1:1 (1 cement: 1 sand)

apply thick cement slurry and apply roller horizontal as well

as vartical ( two times ) up to good quality and size of grain

in elevation as per directed by engineer incharge.- Ground

Providing throating or plaster drip and moulding it to

R.C.C. chajja etc.comp For all Floor

Providing 20 mm. deep finished groove in plaster in line

and level etc. complete. For all floor (M.R.)

Providing & laying granite slab 18mm thick in Window-

Door seal Frame Etc laid on 10mm thick cement mortar 1:4

(1 Cement : 4 Coarse sand) with nessary adhesive material

and finished with flush pointing in white or colour cement,

including rubbing & polishing comp.. (Basic Rate:-

96 Labour Charges For Edge Finished For Granite 27.00 43.43 R.M.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing and laying Vitrified tiles 8 to 10 mm thick, 24" x

24" in flooring treads of steps and landing laid on a bed of

12mm thick cement mortar 1:3 (1 cement : 3 coarse sand)

finishing with flush pointing in white cement.

Providing and laying Vitrified tiles 8 to 10 mm thick, 24" x

24" in skrting risers of steps and dedo on 10mm thick

98 cement plaster 1:3 (1 cement : 3 coarse sand) and jointed 2.00 1,135.80 S.M.

with white cement slurry.

Providing and fixing 35mm thick shutters for Doors,

windows and clearstory windows including anodised

alluminium butt hinges with necessary screws. (A) Indian

teak wood. (i) Fully Panelled.

Providing & fixing M.S.Grills of required pattern to

wooden frames of windows etc. At all floor levels with

M.S. flats at required spacing & frame around square or

round bars with round headed bolts & round eaded bolts

and nuts or by screws incl. Priming coat of Red lead paint

etc. comp. (A) Plain grill For all Floors

Providing and fixing window having extruded aluminium

Powder Coated section frame main outer size 63.50 x

x1.95 mm (of Jindal section no.4605, @ Wt. 1.094Kg/mt)

horizontal Two track member size 61.85 mm x 31.75 mm x

1.20 mm (of jindal section no:8687, @ Wt. 0.695 Kg/mt.)

vertical member of size 61.85 mm x 31.75 mm x 130 mm

(of jindal section no:8758 @ wt. of 0.659 kg/mt) with

101 sliding shutters of horizontal member size 40 mm x18 mm x 3.00 1,705.67 S.M.

1.29 mm ( of jindal section no:8949, @ Wt. of .456 Kg/mt)

vertical member of size 40 mm x 18 mm x 1.29 mm (of

jindal section no:8947, @ Wt. of 0.456 Kg/mt/section

@ Wt. of 0.457 Kg/mt) with 5 mm thick tranparent bronze

colour tineted float glass with powder coated aluminium

fittings and fixtures and transparent silicon sealant glass

fixing to frame as per details etc. complete for window.

(1) The whole work is to be executed through specialized

agency with a guarantee of 10 (Ten) years given on a

102 prescribed proforma duly stamped (2) The rate shall include

for work at all floors & conducting water proof test as

directed. (M.R.)

(B) Providing and laying integral cement based water

proofing treatment including preparation of surface as

required for treatment of roofs, balconies, terraces etc.

consisting of following operations. (a) Applying and

grouting a slurry coat of neat cement using 2.75 kg/sqm of

cement admixed with proprietary water proofing compound

comforming to IS:2645 over the R.C.C. slab including

cleaning the surface before treatment.(b) Laying cement

concrete using broken bricks/brick bats 25 mm to 100 mm

size with 50% of cement mortar 1:5 (1 Cement : 5 Coarse

sand) admixed with proprietary water proofing compound

conforming to IS:2645 ,brick bats is finally covered by

jointless cement plaster 20mm th. in C.M. 1:4 added with

special water proofing compound confirming to IS:2645 &

top smooth finished with trowel with false chequered

marking of 300 mm.size.The treatment is carried along the

vertical surface of the parapet & other adjoining wall up to

height of about 300 mm in a shape of quarter round vata

Incl. curing etc. Comp. With average thickness of 120 mm

and minimum thickness at khurra as 65 mm.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

(c) The whole terrace so finished shall be flooded with

water for a minimum period of two weeks for curing and

for final test. All above operations to be down in order and

as directed and specified by the engineer-in-charge. With

average thickness of 120 mm and minimum thickness at

khurra as 65 mm. (Cement consumption 0.511 Bags / S.M.)

Distempering two coats with oil bound washable distemper

of approved brand& manufacture & of required shade on

wall surface to give an even shade over and & incl. a

priming coat of alkali resistance primer of approved brand

103 after throughly brushing the surface to give an even shade

after throughly brushingthe surface free from mortar

droppings and other foreign matter and also including

preparing the surface even and smooth.

(A)Wall 38.00 75.84 S.M

(B) For ceilings and soffits of stairs 10.00 84.37 S.M

Applying Priming coat over new steel and other metal

surface after over and including preparing the surface by

104 throughly cleaning oil, grease dirt and other foreign matter 2.00 36.74 S.M

and scoured with brushed fine steel wool, scrapers and sand

paper with ready mixed priming paint brushing red lead.

Painting two coat (excluding priming coat) on new steel and

other metal surface with synthetic enemal paint, burshing to

give an even shade including cleaning the surface of all dirt,

dust and other foreign matters.

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

106 specification and directions in shade and colour approved 70.00 82.00 S.M

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Surface preparation: Amount H

LAWN : Area cleaning and side grading, removing

unwanted materials, plants, chrubs,wild grass,

weeds,debris,rubbish,etc. Excavating up to depth 30 C.M

surface dressing leveling, making slopes for drainage

according to landscape, Disposal of unwanted materials

with all labour and tools. Development of lawn including

preparation of bed ground, spreading and mixing the good

soil with Farm Yard Manure, Gypsum, fertilizer soil with

farm Yard Manure, Gypsum, Fertilizer bas required hand

specified. Planting of lawn grass bits roots of approved

quality, watering and specified. Planting of lawn grass bits

roots of approved quality, watering, and specified. Planting

of lawn grass watering mowing, weeding etc. maintenance

of developed lawn for a period of 6 months.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Supplying on site plants with following specifications

.Plants would be in good condition and of specified height.

The rates would be inclusive of all taxes, sales tax,

108 ctroi,transportaion etc. complete F.O.R. site. (G) Garden

Conditions of plant would be verified at the time of selction

as well delivery. All complete and as per instructions of the

Engineer-in-charge.

Lagerstroemia thorell II - 3.66 m ht 60.00 Nos.

Millingtonia hortensis - 3.66m ht 60.00 Nos.

Azadirachta Indica - 2.13m ht 100.00 Nos.

Gresses & Bamboos

Bambusa valgaris - 1.83m ht. 120.00 Nos. 75.00 9000.00 35.00 75.00 Nos.

Nephrolepis exalotta smithi - 0.45x0.30m 150.00 Nos.

109 Wall Vinyl Sticker 90.00 28.00 SqFt.

Eco Solvent Vinyl Sticker (120 gsm) with Lamination (100

Solvent Vinyl Sticker (120 gsm) with Lamination (100

112 5mm PVC sheet Eco Vinyl (Any size) - 55.46 -

Decorative theme base designing & painting with all

waterproof materials

Slogan writing on walls with designing, Painting at Place

including necessary surface preparation, cleaning, removal

of dust & other foreign material and back ground priming

coat over the surface.

Recharge Borewell

Drilling 300 mm diameter borewell in all types of strata up

to required depth including cost of bentonite powder,

carting rings, cutter, other required materials, labour

charges etc. complete. The drilling shall be done by mud

flushed rotary equipment and bore holes should withstand

at least till completion of subsequent activities like

assembly jointing, lowering of casing / strainer pipes,

gravels packing, yield testing etc, complete up to required

depth as shown in drawing and directed by engineer

Cleaning of existing unusable / non working borewell by

applying air compressor of capacity not less than

CFM/200 PSI for minimum two hours or up to the

116 availability of sand free discharge whichever is later 0.00 6,000.00 No -

including all labour charges and hire charges of compressor

and other equipment etc. complete as directed by engineer-

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Excavation for foundation in and all kinds of soil including

leveling and ramming the bottom of trenches and

foundation pits, shoring, strutting, dewatering if required,

slush removing, filling the sides up to original ground level

for rectangular chamber and trench.

Providing and laying Cement Concrete nominal mix 1:3:6

(1 cement: 3 coarse sand : 6 hand broken stone aggregate

20mm nominal size) and curing complete including cost of

form work as per drawing in chamber etc. complete.

Providing & laying 230 mm Thick Fly ash Brick masonry

having rushing strength not less than 35 kg/sq.cm. 1:6 (1

cement : 6 fine sand) with scaffolding, watering, curing etc.

complete with all labours and materials. various area as

directed by Engineer-incharge.Upto G.L/P.L.

Providing 10 mm thick Cement Plaster in single coat on

brick/concrete walls far interior plastering up to Floor two

level and finished even and smooth in cement mortar 1:3(1

cement 3 sand various area as directed by incharge) .

Supplying and fixing 100 mm dia. standard PVC pipe of

approved Quality (Prince, Supreme, Finolex) with ISI mark,

including a perforated portion surrounding wire mesh

extended upto half the length of filter chamber, jali at the

end in filter chamber and fitting of outside end with casing

pipe of borewellincluding excavation, filling of earth,

plumbing, fittings, clamping etc, complete to divert the

water from filter chamber to borewell as shown in drawing

and directed by engineer –in- charge..

Supplying and filling clean best quality of well- sorted sand

having size 1 mm to 2 mm in layer of required thickness in

filter chamber as per drawing and as directed by Engineer

Supplying and filling clean best quality of well sorted- "

SEVALIYA" sorted peagravel having size 6 mm to 10 mm

123 in layer of required thickness in filter chamber as per 6.00 1,800.00 C.M.

drawing and as directed by Engineer –in- charge.

Supplying and filling clean best quality of well- sorted brick

bats having size 50 mm to 150 mm in layer of required

thickness in filter chamber as per drawing and as directed

by Engineer –in- charge.

Supplying and fixing a display board of size 450 mm x

mm or higher, near the recharge system or on outer side of

125 one wall of filter chamber with letters written 2.00 300.00 No.

“GROUNDWATER RECHARGE SYSTEM”.

Supplying and fixing of a cover made up of 2 mm thick

Poly Carbonate sheet on painted Mild Steel square pipes of

25 mm x 25mm x 2 mm and channels of 25mm x 25 mm x

2 mm as shown in drawings over filter camber including all

126 materials, fittings and labour charges etc, complete The 15.13 900.00 S.M

fixing of cover over walls should have arrangement of

removing it from the wall for cleaning of filter chamber and

re-fixing again from time to time as shown in drawing and

directed by engineer – in- charge.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Supplying and fixing 100 mm dia. Standard PVC pipe of

approved Quality (Prince, Supreme, Finolex) with ISI mark,

of required length including two valves at outside of

brickmasonary wall and nylon mesh filter bag 100 x

mm fitted on inside end of pipe including materials, fittings,

clamping, plumbing etc, complete to keep away debris from

roof top water entering into the filter chamber as shown in

drawing and directed by engineer – in- charge.

Providing, Supplying, Fixing in bore hole 160 mm dia

Kg/cm2 P.V.C Pipe of approved Quality (Prince,

Supreme,Finolex) with ISI mark, in borewell / filter

128 chamber, including 3.2 mm x 75 mm vertical perforations 98.00 650.00 R.M.

with spacing of 4 to 5 mm (or equivalent standard

openings) in necessary lengths and necessary fittings and as

per site situation and as directed by engineer –in- charge.

Supplying and filling clean best quality of well- sorted

"SEVALIYA " pea gravel having size 4 mm to 6 mm

surrounding casing pipe in borewell as per drawing and as

directed by Engineer –in- charge

Providing, fixing and binding SS-304 Hexagonal wire mesh

130 surrounding the perforated casing pipe in filter chamber as 0.90 413.00 S.M

directed by Engineer –in- charge.

Providing, supplying and fixing 100 mm dia. 6 kg / cm2

standard PVC pipe with ISI mark, in brick masonary wall

with jali at outside of wall and nylon mesh filter bag 100 x

131 500 mm fitted on inside end of pipe including plumbing, 8.00 350.00 No

fittings, clamping etc, complete to keep away debris from

surface runoff entering into the filter chamber as shown in

drawing and directed by Engineer –in- charge.

Demolition including stacking of serviceable

materials and Disposal of unserviceable materials with lead

(a) unreinforced cement concrete 3.90 270.00 CM

(b) Brick work(Cement mortar) 270.00 -

Annual pre-monsoon maintenance - cleaning, replacing

of gravel sand filter media, flushing with water etc.

complete as per site situation and directed by

Engineering-in-charge.

Steel work, welded in built up sections framed

work including cutting, hoisting, fixing in position and

applying a priming coat of red lead paint. (A)In

beams and joists, channels angles Tees, flats, with

connecting plates or angle cleats as in main and cross

beams. Hip and jack rafters, purlins conneted to

common rafters and directed by Engineering-in-

Supplying and fixing 100 mm dia. Standard PVC

Valve of approved Quality with ISI mark,

135 including materials, fittings, clamping, plumbing etc, 0.00 1,000.00 No -

complete to as shown in drawing and directed by

engineer – in- charge.

Storm-Drainage Works

Providing, Lowering & laying joining R.C.C. NP3 CLASS

136 Pipe In C.M. 1:1 of following nominal internal diameters

incl. Testing of pipes and joints etc.Comp R.M.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing constructing brick masonary INLET CHAMBER

OF 750*600*1500 mm internal dimension with necessary

excavation refilling 350 mm th Br. masonary in C.M

1:4,150 mm th. p.c.c. & benching in c.c. 1:2:4,12mm th.

plaster in C.M. 1:3 for inside & cement pointing in C.M.

1:3 for o/s prov. & fixing precast RCC frame & cover of

M30 grade as per drawing & specification. rate for 1.5 mt

Add. or ded. Rs. 701 per every 10 cm increase or decrease

Excavation for foundation includ.sorting out & stacking of

useful materials & disposing of the excavated stuff upto

138 50 mt. Lead & all lift, watering etc. Comp. (A) Loose

Boring holes 3.5 mt.deep in ordinary soil ( for cast in situ

piles) & disposal of the surplus excavated soil as

directed within a lead of 50 M. For following diameter

Providing & Filling Rubbles including hand packing &

filling interstics with Quarry Spalls complete for all leads

Providing & laying C.C 1:3:6 (1cement :3 coarse sand :6

141 Crushed stone agg 20m.m Nominal size)&curing comp. 9.00 3,095.25 C.M

excl. cost of form work in :(a) foundation & Plinth

Providing & laying cement concrete 1:2:4 (1 cement:2

sand:4 graded stone agg. 20 mm nominal size)& curing

142 comp. Includ.cost of form work but exclu. Cost of

reinforcement for reinforced concrete work in : (A)

Foundation, footing, Base of columns and Mass concrete.

Plinth area/Grade slab base 14.00 3,741.69 C.M

Providing, mixing, placing, compacting by machine

vibrator, curing, testing M25 Design mix concrete as per IS

143 456:2000 (latest revision) and as per tender

specification in all items including cost of form work and

rendering butexcluding cost of reinforcement

(A) foundation, footing, base of columns and mass concrete 10.00 4,332.00 C.M

Providing, mixing, placing, compacting by

machine vibrator, curing, testing M25 Design mix concrete

as per IS 456:2000 (latest revision) and as per tender

specification in all items including cost of form work and

excluding cost of reinforcement

(2) Having cross sectional area more than 0.085 sq. mt .up

(3) Having cross sectional area more than 0.12 sq. mt . 14.00 7,067.84 C.M

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & laying C.C 1:3:6 (1cement :3 coarse sand :6

145 crushed stone agg. 20 m.m Nominal size)& curing comp. 3.00 4,085.83 C.M

incl. cost of from work in: wall caps/ copings.

Providing & fixing IS Mark TMT Bar FE 500D

146 reinforcement for R.C.C. work incl. bending, binding & 4257.00 77.29 K.G

placing in position etc. comp. Upto G.L./P.L.

Providing and construction Brick work using common

burnt clay building bricks having crushing strength not less

than 35 kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:6 (1- Cement : 6 -fine sand)(C) Fly Ash Bricks

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each disposited

layer by ramming and watering

(EXCAVATION)-(PCC-FOUNDATION-

Filling in foundation and plinth with murrum or selected

149 soil in layers of 20cm. thickness including watering, 78.00 301.78 C.M

ramming and consolidating etc. complete.

carrying out plinth treatment to post construction/existing

structure by spraying chemical solution for termite control

treatment including labour and material consisting with ISI

specification using chlordene and chiorpurfiles 20 EC as

per 6131_part II concentration weight one litter give 1%

concentration inclusive of one litter chemicals emulsions

application at the rate of 5 litter chemicals /sqmt of surface

is recommended as per IS.

Providing & Applying 20mm. Th. Heavy Roller plaster on

walls or similar surfaces at all floor levels consisting of

mm av. Th. Backing coat of C.M. 1:3 (1 cement:3 sand) &

151 mm. th. Finishing coat of C.M. 1:1 (1cement: 1 sand) 32.00 324.00 S.M

pplythick cement slurry and apply roller horizontal as

ellasvertical ( two times ) up to good quality and size of rain

inelevation as per directed by engineer incharge

Providing & applying two coats of weather shield max

paint (3 coats may be required in case of darker

colours.)of ICI Dulux or Apex Ultima of Asian Paint

including applying exterior acrylic primer coat as per

152 manufacturers specification and directions in shade and 32.00 82.00 S.M

colour approved by architects, on exterior surfaces of the

building including scaffolding, preparing the surface,

watering, curing etc. complete and as directed by the

architects and manufacturers.

Surface Preparation

Work Above Plinth:

Providing, mixing, placing, compacting by machine

vibrator, curing, testing M25 Design mix concrete as per IS

153 456:2000 (latest revision) and as per tender specification in -

all items including cost of form work and rendering but

excluding cost of reinforcement

(2) Having cross sectional area more than 0.085 sq. mt .up

(2) Having cros sectional area more than 0.08 sq. mt and

upto 0.12 sq.mt.

(4) Having more than 13 cm. Thickness 13.00 6,793.97 C.M

(D) Lintels: 2.00 9,963.33 C.M

(E) Chhajja 2.00 7,119.46 C.M

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & laying C.C 1:3:6 (1cement :3 coarse sand :6

154 crushed stone agg. 20 m.m Nominal size)& curing comp. 2.00 4,085.83 C.M

incl. cost of from work in: wall caps/ copings

Providing & fixing IS Mark TMT Bar FE 500 / FE 500d

155 reinforcement for R.C.C. work incl. bending, binding & 4405.00 77.29 K.G

placing in position etc.comp.---

Providing & construction brick work using Fly Ash bricks

having crushing strength not less than 35 Kg./sq.cm. in

foundation & plinth in C.M. 1:6 (1 cement:6 sand ) etc.

Providing & constructing Half brick masonary in Fly Ash

157 bricks having crushing strength not less than 70 kg/sq.cm in 159.00 712.81 S.M

c.m 1:4 (1 cement: 4 sand) curing etc complete

Providing & Applying 15mm.th.cement plaster in single

coat on brick/concrete walls similar surfaces for plastering

& finished even & smooth with a floating coat of cement

slurry mixed with admixture of lime or neeru in required

proportion etc. comp. in C.M 1:3 (1 cement : 3sand) (A)

For wall and similar surfaces -- Ground Floor

Providing & Applying 10mm.th.cement plaster in single

coat on brick/ concrete walls similar surfaces for plastering

& finished even & smooth with a floating coat of cement

slurry mixed with admixture of lime or neeru in required

proportion etc. comp. in C.M 1:3 (1 cement : 3sand) (A)

For wall and similar surfaces -- Ground Floor

PUBLIC UTILITY+ CHAJJAS BOTTOM 99.00 199.28 S.M

Providing and fixing 150 mm wide, approved quality

chicken wire mesh (FRP / PVC)at junction of brick work

and RCC work or two dissimilar surfaces, at all heights

fixed by nails, rowal plugs or tag by cement mortar 1:3

before applying the plaster, including curing, scaffolding all

complete as directed.

Providing & Applying 20mm. Th. Heavy Roller plaster on

walls or similar surfaces at all floor levels consisting of

mm av. Th. Backing coat of C.M. 1:3 (1 cement:3 sand) &

161 8mm. th. Finishing coat of C.M. 1:1 (1cement: 1 sand) 168.00 324.00 S.M

pplythick cement slurry and apply roller horizontal as well

svartical ( two times ) up to good quality and size of grain

inelevation as per directed by engineer incharge.

Providing throating or plaster drip and moulding it to

R.C.C. chajja etc.comp.. For all floor

Providing 20 mm deep finished groove in plaster in line and

level etc. Comp. For all Floor (M.R.)

Providing and laying Vitrified tiles 8 to 10 mm thick, 24" x

24" in skrting risers of steps and dedo on 10mm thick

cement plaster 1:3 (1 cement : 3 coarse sand) and jointed

with white cement slurry.

Providing & laying Vitrified tiles of 8mm thick of Orient,

Kajaria,Jhonson, Nitco, Somani, Bell, Asian or Euro make

in flooring,treads of steps & Landing laid on bed of 20 mm

(Average) base of cement mortar 1:6 (1 Cement : 6 Coarse

165 sand) on new surface or fixing on existing flooring by 86.00 1,467.72 S.M

adhesive material including dismentaling of existing

flooring and jointed with colour cement slurry including

finished with flush pointing & cleaning the surface etc.

comp.Size 24" x 24" For Antiskid tiles

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing and laying polished Kota stone slab flooring over

20mm (Average) thick base of cement mortar 1:6 (1-

cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 -

coarse sand) laid over and jointed with grey cement slurry

mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete. (A) 25mm thick

Providing and laying polished kota stone slab 25mm thick

in risers of steps,skirting Dedo and pillars laid on 10mm

thick cement mortar 1:3 (1-Cement : 3 coarse sand) and

jointed with gray cement slury mixed with pigment to match

the shade of slab including rubbing and polishing etc.

Providing and fixing FRP frame size 125x65 mm and

mm thick FRP shutter with wood grain raised panneled

design finish shutter having extra reinforcement on sides &

edges in Gel coat finish. The core of the shutter & frame is

to filed up with injected polyurethane foam done in situ

168 along with embedded wooden pieces for stiffening & also 35.00 2,019.98 S.M

taking hinges & fintures. The whole FRP frame & shutter is

to be water proof weather proof, termite proof & resistance

to mild acid/alkali. Rates are to be inclusive of S.S. hinges

with fastener sleeve & alluminium fixtures & fasteningsFor

Providing & fixing 35mm.th. Flush Door Solid Double

Core type Both Face water proof Ply Vennered & 1.5 mm

th.laminate shall be pasted on both side with adhesives as

specified by the manufacturers. The laminate shall be as per

approved shade & texture, of make incl. Sal wood frames of

finished size 12cm x 7cm.incl. S.S. Hinges with nessary

screws & Anodized aluminum fixtures & fastenings For all

Providing and fixing window having extruded aluminium

colour anodized section frame main outer size 63.50 x

38.10 x1.95 mm (of Jindal section no.4605, @ Wt.

1.094Kg/mt) horizontal Two track member size 61.85 mm x

31.75 mm x 1.20 mm (of jindal section no:8687, @ Wt.

0.695 Kg/mt.) ertical member of size 61.85 mm x

mm x 130 mm (of jindal section no:8758 @ wt. of

kg/mt) with sliding shutters of horizontal member size

mm x18 mm x 1.29 mm ( of jindal section no:8949, @ Wt.

of .456 Kg/mt) vertical member of size 40 mm x 18 mm x

1.29 mm (of jindal section no:8947, @ Wt. of

Kg/mt/section 8948, @ Wt. of 0.457 Kg/mt) with 5 mm

thick tranparent bronze colour tineted float glass with

powder coated aluminium fittings and fixtures and

transparent silicon sealant glass fixing to frame as per

details etc. complete for window.For all Floors.

Providing and fixing standared extruded ofalluminium

section of size 63mm x 38.10mm x1.2mm , @ Wt.

171 Kg/mt with colour Powder Coated alluminium frame for 8.00 1,175.56 S.M

ventilation with 5 mm thick frosted glass as details etc

complete for Ventilation

Providing & laying granite slab 18 mm thick in Window-

Door seal,Frames Etc laid on 10 mm thick cement mortar

1:4 (1 Cement: 4 Coarse sand) with necessary adhesive

material and finished with flush pointing in white or colour

cement, including rubbing & polishing comp. (Basic Rate:

Rs. 1000.00/S.M.).For all Floors.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

173 Labour Charges For Edge Finished For Granite for all floors 490.00 43.43 R.M

Painting two coat (excluding priming coat) on new

steel and other metal surface with synthetic enemal

174 paint, burshing to give an even shade including 1.00 68.57 S.M

cleaning the surface of all dirt, dust and other foreign

matters. (A) For plain grill For all Floor

(1) The whole work is to be executed through

specialized agency with a guarantee of 10 (Ten) years

given on a prescribed proforma duly stamped (2) The rate

B) Providing and laying integral cement based

water proofing treatment including preparation of

surface as required for treatment of roofs, balconies,

terraces etc. consisting of following operations.

(a) Applying and grouting a slurry coat of neat

cement using 2.75 kg/sqm of cement admixed with

proprietary water proofing compound comforming to

IS:2645 over the R.C.C. slab including cleaning the

surface before tratment.(b) Laying cement concrete using

broken bricks/brick bats 25 mm to 100 mm size with 50%

of cement mortar 1:5 (1 Cement : 5 Coarse sand) admixed

with proprietary water proofing compound conforming

to IS:2645 ,brick bats is finally covered by jointless

cement plaster 20mm th. in C.M. 1:4 added with special

water proofing compound confirming to IS:2645 & top

smooth finished with trowel with false chequered

marking of 300 mm.size.The treatment is carried

along the vertical surface of the parapet & other

adjoining wall up to height of about 300 mm in a shape of

quarter round vata Incl. curing etc. Comp. With

average thickness of 120 mm and minimum thickness at

(c) The as whole terrace so finished shall be flooded

with water for a minimum period of two weeks for

curing and for final test. All above operations to be down

in order and as directed and specified by the engineer-in- 107.00 511.00 S.M

charge. With average thickness of 120 mm and

minimum thickness at khurra as 65 mm. (Cement

consumption 0.511 Bags / S.M.)

Providing and laying broken china mosaic flooring

forterrace using 12mm to20mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plainor slope and

176 to be tempered to bring mortar creme out upto surface using 107.00 779.70 S.M

white cement including rounding off junctions and

extending them upto 15 cmalong the wall clearing with

water and oxalic acid etc. as directed

Apply two coats of putty and two coats of primer of

approved brand and manufacture on new wall surface to

177 give an even shade including thoroughly brushing the 663.00 40.59 S.M

surfacefreefrommortardroppingandothermatterand sand

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

178 surface to give an even shade including throughly brushing 663.00 83.36 S.M

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & applying two coats of weather shield max

paint (3 coats may be required in case of darker colours.)of

ICI Dulux or Apex Ultima of Asian Paint including

applying exterior acrylic primer coat as per manufacturers

179 specification and directions in shade and colour approved 169.00 82.00 S.M

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

ProvidingPreparation

& laying : granite slab 18mm thick in flooring,

treads of steps and landing laid on bed of 20mm thick

cement mortar 1:6 (1 Cement : 6 coarse sand) or lime

mortar 1:1.5 laid and finished with flush pointing in white

or colour cement including rubbing and polishing complete.

(Basic Rate:- Rs.1347.46/S.M.)

Providing & laying granite slab 18mm thick in skirting,

risers of steps,dedo and pillars laid on 10mm thick cement

181 mortar 1:4 (1 Cement : 4 Coarse sand) and finished with 1.00 2,449.00 S.M

flush pointing in white or colour cement including rubbing

& polishing comp.. (Basic Rate:- Rs.1347.46/S.M.)

Providing and fixing M.S. Fan clamps type 1 to 16 mm dia

M.S. bar bent to shpe with hooked ends to RCC slabs

curing, layig including painting the exposed portion

of loops, all as per standard design complete.

Providing & fixing in position collapsible steel shutters

with vertical channels 20 x10 x 2 mm. Braced with flat iron

diagonals 20 x5mm size with top & bottom rails of T-

iron 40x40x6mm. with 38mm dia. steel pulleys comp.

with bolts, locking arrangements, stoppers, handles

incl. applying a priming coat of Redlead paint etc. comp.

184 Wall Vinyl Sticker 30.00 28.00 SQ.FT

Eco Solvent Vinyl Sticker (120 gsm) with Lamination (100

Solvent Vinyl Sticker (120 gsm) with Lamination (100

187 5mm PVC sheet Eco Vinyl (Any size) 30.00 55.46 SQ.FT

Decorative theme base designing & painting with all

waterproof materials

Providing and fixing rebar of following diameter

using chemical grout of Swanchore/Hilti/Fischer or

equivalent make including cost of all equipments, tools,

material, labour, etc. Standard procedure as

mentioned in manufacturer's specifications shall be

strictly followed, which shall be submitted and got

approved from the authority prior to start of work. The

rate shall also include cost of drilling of hole of required

diameter and depth as mentioned in manufacturer's

specification, cleaning the hole with required air blower

and other necessary tools and tackles, positioning,

providing and grouting chemical, allied fixtures and

fasteners, etc. but excluding the cost of reinforcing bar etc.

includes necessary scaffolding, staging, labour, tools

and equipments, etc. complete as directed by the

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Water Supply & Sanitation

Prov.& Fixing water closet squatting pan (Orissa

type W.C.pan) at all floor levels, size 500mm x 400 mm

incl. 100 mm size "P'or "S" trap for water closet

squatting pan joining the trap with the pan & soil

pipe in C.M. 1:1 (1cement :1 fine sand) etc. Comp.(A)

Vitreous china long pattern

Providing and fixing Wash Down Water closet

European type W.C. pan with integral P or S trap with

normal closing seat cover L bend ncluding jointing the trap

with soil pipe in cement mortar 1:1 (1 cement : 1 find sand)

china pattern - I

Providing Metropole Flush Valve Dual Flow 40mm

Size (Concealed Body)

Providing & fixing Wash Hung basin with single hole

for pillar tap , Size- 550 x 400 mm at all floor levels, with

C.I. or M.S. Brackets painted white incl. cutting holes &

making good the same etc. complete. For all Floor

Providing & fixing 600 mm.x 450 mm. mirror of

superior glass at all floor levels, mounted on 6 mm. th.

A.C. sheet or plywood sheet & fixed to wooden plugs

with C.P.brass screws and washers etc. For all Floor

Providing & fixing C.P. brass pillar cock with copper

connection, C.P. brass screws complete

Providing & Fixing 15 mm Dia bib tap with wall Flange at

all floor levels, polished bright etc. comp

Providing & Fixing 15 mm Dia 2 way bib tap with

wall Flange at all floor levels, polished bright etc. comp

Providing & fixing 15mm C.P. brass angle valve

(Stop Cock) with C.P. copper connecting pipe 450 mm

198 long and nuts, washer and brass flange complete, 7.00 1,564.36 NOS

including cutting and making good the wall where

Providing and fixing Towel Ring fabricated from

seamless stainless steel tube 2mm thick in bath room with

polished wall flange at end of bars with heavy

duty anchor fasteners & accessories

Providing & Fixing stainless steel recessed type Soap

200 dish of approved make. Including providing & fixing 7.00 839.91 NOS

screws, washers, cutting & making good the walls.

Providing & fixing of overhead shower 80 mm (3”)

201 dia with 3 flow with Overhead Shower arm 200 mm with 3.00 1,526.42 NOS

wall flange complete

Providing and fixing PVC SWR Nahni trap IS

for drain - 75 mm diameter with jali of the following

202 nominal diameter of self cleaning design with C.I. 10.00 586.27 NOS

scread down or hinged grating including the cost of

cutting and making good the walls.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & Fixing U-PVC pipe (SWR) confirming to

IS no. 13592 (Type"B") of Prince/ Supreme/ Jain/

Astral/ Tulsi/ Finolex make for soil and waste

discharge system at all floor levels incl. All fixtures

like bends, tees,shoe etc. jointed with resin of

approved brand & manufacture etc. comp.(M.R.)

(A) 75mm Dia 40.00 412.00 RMT

(C) 160 mm. Dia.

Providing & fixing U-PVC pipes Confirming to IS no.

13592 (Type "A") of Prince/ Supreme/ Jain/ Astral/ Tulsi/

204 Finolex make for rain water at all floor levels incl.

fixtures like bends, tees, shoe etc joined with resin of

approved brand & manufacture etc. comp. (M.R.)

(C) 160 mm. Dia.

Providing and fixing in position P.V.C. cowl vent to

205 pipes of prince, suprime, jain Or Eqivalent make

etc. Comp (M.R).

40 mm dia 4.00 40.00 NOS

50 mm dia 4.00 50.00 NOS

Providing & Fixing Kathi around the vertical PVC

drainage pipes for concealing with cement plaster

206 20 mm avg thickness(CM 1:3 [1 cement :3 coarse

sand]) finishing as per instruction given by Eng. incharge.

75mm PVC pipe 20.00 173.00 RMT

Providing & Fixing P.V.C. pipes (SCH-80) of

Prince/ Supreme/ Jain/ Astral/ Tulsi/Finolex make for

water supply line at all floor levels incl. fixtures like bends,

tees, shoe etc joined with resin of approved

brand & manufacture etc. comp. Pipe shall be fixed on the

wall the help of clamp at every two meter C/C or

shall be concealed as directed including necessary

fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all

15 mm dia 15.00 166.00 RMT

25 mm dia 25.00 256.00 RMT

50 mm dia 15.00 510.00 RMT

65mm dia 0.00 635.00 RMT -

Providing and fixing G.I. holder "Z" clamps at all

208 floor level,of approved pipes including cost of cutting holes

and making good the wall etc. comp. (M.R)

(A) 40 TO 50 mm Dia 15.00 62.00 NOS

(B) 75 to 90 mm Dia 10.00 75.00 NOS

(C) 150 mm to 200 mm dia 0.00 98.00 NOS

Providing and fixing gun metal check or non return full way

wheel valve at floor levels,etc. complete.

(A) 15 mm. dia 0.00

Providing and fixing abonite ball cock of approved quality

as directed etc. comp.

(A) 25mm. dia. 6.00 102.91 NOS

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing, Lowering and laying joining R.C.C. NP2

CLASS pipe in cement mortar in proportion 1:1 of

following nominal internal diameters including testing of

pipes and joints etc. complete.

Providing and fixing s.w. Gully trap with C.I. gratting brick

masonary chamber and water tight Pre cast R.C.C.cover of

300mm X 300mm size (inside) including plastering smooth

212 inside and outside 15 mm thick in C.M 1:3 etc. 4.00 1,098.05 NOS

comp.i) square mouth traps (A)300 MM X

type.For all Floors.

Prov. & Fix. 10 cm.x15 cm.(4" x 6") S.W. trap with

Inside dimension ,455 x 610 mm & 450 mm deep

sewer trap chamber with 23 cm th' B.B. masonary

walls in C.M 1:5 with cement plaster 15 mm th' in C.M.

1:3 inside & outside to exposed faces, R.C.C. top slab with

1:2:4 mix ( 1 cement: 2 Sand : 4 Grade stone aggregate

20mm size) ,Foundation concrete 1:5:10 & fixing C.I.

cover with frame to be not less than 38 kg. On top

etc. comp. for single pipe.'.(A) Precast RCC heavy duty

Cover instead of C.I. Cover

(A).Same as above but Precast RCC heavy duty

Cover 4.00 2,915.61 NO

instead of C.I. Cover

Extra for every additional depth of 0.1 mt.beyond 0.45 mt. 0.00 - NO -

Providing & construction simple chamber of 23 cm. th'

B.B. Masonary in C.M 1:5 with cement plaster 15 mm th' in

C.M. 1:3 inside & outside to exposed faces, R.C.C. top

slab with 1:2:4 mix ( 1 cement: 2 Sand :

Grade stone aggregate 20mm size), Foundation concrete

1: 5: 10 & fixing C.I. cover with frame to be not less

than 38 kg. On top etc. comp. Inside dimension, 455 x

mm &450 mm deep for single pipe

(A).Same as above but Precast RCC heavy duty

Cover 4.00 2,681.76 NOS

instead of C.I. Cover

Extra for every additional depth of 0.1 mt.beyond 0.45 mt. 0.00 242.39 NOS -

Providing and fixing C.I. Machinehole cover 0.60 x

mt. Size having weight not less than 35 Kg. etc. complete.

Providing and fixing G.I, Rain water spout of 50 mm dia

and 30 cm Length

Providing & fixing white vitreous china urinal of size

x325mm as per IS-2556 (Part-2 ) with C.I. hangers and

217 15mm dia. C.P. spreader,32mm dia CP bottle trap and pipe

to wall with C.P. flange complete including cutting and

making good the walls and floors wherever required.

Make- CeraCat. No. S4020103, Parry ware C0501*,

Jaquar URS-WHT 13261H ,HindWare BACK SMALL 5.00 2,535.70 NOS

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & fixing at all floor levels,both face

polished machine cut edge Marble slab for urinal

218 partition joined with grey/White cement slurry (1:1) -

incl. Rubbing & polishing etc. complete. (M.R.)( Basic

Cost Rs. 450/S.M.)

Providing & laying ordinary C.C.1:1.5:3 mix for R.C.C.

work incl. boxing, centering, vibrating, curing &

mixed with approved water proofing cement

compound or "CEMWET"or"PIDICRETE

LW"integral water proofing admixture as water

proofing agent to be mixed with 50 kg. cement bag shall be

as recommended by the manufacture of the water

proofing material, concrete work for top, bottom slab &

side pardi for under ground Tank & Item incl.

219 Necessary excavation & refilling the available earth,

cm th' C.C 1:4:8 for bedding concrete, Half B.M. in C.M.

1:4 outside wall, inside R.C.C. pardi as per

design, 10mm.th. water proofing cement plaster in C.M.

1:3 with smooth finishing,watering etc.Comp.to all inner

face of tank curing etc. comp. incl. Locking

arrangement, outlet, inlet, overflow & wash out pipe

arrangement as necessary & C.I. Cover 0.60 x .045

weight not less then 35kg. etc. com. as per structural

drawing excluding Steel & as directed by Engineer-in-

Under Ground water Tank 5000.00 6.87 LIT

Providing & Laying white glazed tiles 6mm. th. of

Orient, Kajaria, Jhonson, Nitco, Somani, Bell make at

all floor levels, in flooring, treads of steps & landings laid

on a bed of 12 mm. Av. Th.C.M.1:3 (1cement : 3 sand)

finished with flush pointing in white cement etc.com. For

Under Ground water Tank 2.00 900.29 S.M

Providing & Laying white glazed tiles 6mm. th. Of

Orient, Kajaria, Jhonson, Nitco, Somani, Bell make at

all floor levels in skirting risers of steps & dado on

221 mm. th. C.M.1:3 (1cement :3 sand) including

necessary cement paste for fixing and joined with

white cement slurry

etc.complete. For all floors

Under Ground water Tank (SIDE) 13.00 932.02 S.M

Providing & fixing IS Mark TMT FE 500D reinforcement

222 for R.C.C. work incl. bending, binding & placing in

position etc. comp. Upto G.L./P.L.

Upto G.L./P.L. 450.00 77.29 K.G

Providing erecting and fixing double

coated Sintex/Super/Reno PVC (ISI) mark water tank of

223 required capacity each with all necessary fittings & 4000.00 3.95 LIT

connection etc.

complete on terrace.

Excavation for foundation including sorting out and

224 stacking of useful materials and disposing of the excavated

stuff up to 50 mt. lead and all lift, watering etc.comp.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Boring holes 3.5 mt.deep in ordinary soil (for cast in

situ piles) & disposal of the surplus excavated soil as

directed within a lead of 50 M. For following diameter of

For 300 mm Dia. 24.00 401.28 R.M.

Providing and laying cement concrete 1:4:8 (1 cement :

226 sand : 8 graded stone aggregates 40 nominal size) and 4.00 2,769.69 C.M.

curing complete excluding cost of form work in :

Providing and laying ordinary cement concrete work

1:1.5:3 ( 1 cement, 1.5 sand, 3 graded stone aggregates

227 mm nominal size ) & curing comp.including cost of form

work but excluding cost of reinforcement for reinforced

concrete work in:

(A) Foundation, footing, Base of columns and Mass

Providing and laying ordinary cement concrete 1:1.5:3 (

cement, 1.5 sand, 3 graded stone aggregates 20 mm nominal

228 size ) finishing smooth curing etc. complete including cost

of form work but excluding cost of reinforcement for

R.C.C. work in: Up to G.L./P.L.

(1) Having c/s area up to 0.08 s.mt 1.00 12,844.32 C.M.

(B) BEAM:(G.B/P.B)

(1) Having c/s area up to 0.08 sq. mt. 2.00 9,102.61 C.M.

Providing & fixing IS Mark TMT Bar FE 500D

229 reinforcement for R.C.C. work incl. bending, binding & 590.00 77.29 K.G

placing in position etc. comp. Upto G.L./P.L.

Brick work using common bunt clay buliding bricks having

230 crushing strength not less than 35 Kg./sq.cm. in C.M. 1:6 2.00 4,441.11 C.M.

(1 cement:6 fine sand ) (c) Fly Ash Bricks - Ground Floor

Filling in foundation and plinth with murrum or selected

231 soil in layers of 20cm.thickness including watering, 11.00 301.78 C.M.

ramming and consolidating etc. complete.

Providing & Applying 20mm. Th. Heavy Roller plaster on

walls or similar surfaces at all floor levels consisting of

mm av. Th. Backing coat of C.M. 1:3 (1 cement:3 sand) &

8 mm. th. Finishing coat of C.M. 1:1 (1 cement: 1 sand)

apply thick cement slurry and apply roller horizontal as well

as vartical ( two times ) up to good quality and size of grain

in elevation as per directed by engineer incharge.--- Upto

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

233 specification and directions in shade and colour approved 11.00 82.00 S.M.

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Providing & laying ordinary cement con.1:1.5:3

(1cement:1.5sand: 3 graded stone agg. 20 mm nominal size)

finishing smooth curing etc. comp. Incld.Cost of form work

but excl. Cost of reinforcement for R.C.C. Work in :

(1)Having c/s area up to 0.08 s.mt- Ground Floor Column 1.00 12,844.32 C.M.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

(2) Having c/s area more than 0.08 sq. mt. & upto

(3) Slabs having more than 10 cm. and upto 13 cm.

Providing & fixing IS Mark TMT Bar FE 500D

235 reinforcement for R.C.C. work incl. bending, binding & 510.00 77.29 KG

placing in position etc. comp.-Ground Floor

Brick work using common bunt clay buliding bricks having

236 crushing strength not less than 35 Kg./sq.cm. in C.M. 1:6 5.00 4,441.11 C.M.

(1 cement:6 fine sand ) (c) Fly Ash Bricks - Ground Floor

Providing & Applying 10mm.th.cement plaster in single

coat on brick/concrete walls similar surfaces for plastering

& finished even & smooth with a floating coat of cement

slurry mixed with admixture of lime or neeru in required

proportion etc. comp. in C.M 1:3 (1 cement : 3sand) (A)

For wall and similar surfaces - Ground Floor

Providing & Applying 20mm. Th. Heavy Roller plaster on

walls or similar surfaces at all floor levels consisting of

mm av. Th. Backing coat of C.M. 1:3 (1 cement:3 sand) &

238 8 mm. th. Finishing coat of C.M. 1:1 (1 cement: 1 sand) 33.00 324.00 S.M.

apply thick cement slurry and apply roller horizontal as well

as vartical ( two times ) up to good quality and size of grain

in elevation as per directed by engineer incharge.

Providing throating or plaster drip and moulding it to

R.C.C. chajja etc.comp For all Floor

Providing & laying granite slab 18mm thick in flooring,

treads of steps and landing laid on bed of 20mm thick

cement mortar 1:6 (1 Cement : 6 coarse sand) or lime

240 mortar 1:1.5 laid and finished with flush pointing in white 4.00 2,410.00 S.M.

or colour cement including rubbing and polishing complete

( Basic Rate:- Rs.1347.46/S.M.)

Providing & laying granite slab 18mm thick in skirting,

risers of steps, dedo and pillars laid on 10mm thick cement

241 mortar 1:4 (1 Cement : 4 Coarse sand) and finished with 3.00 2,449.00 S.M.

flush pointing in white or colour cement including rubbing

& polishing comp.. (Basic Rate:-s.1347.46/S.M.)

Providing and laying Vitrified tiles 8 to 10 mm thick, 24" x

24" in flooring treads of steps and landing laid on a bed of

12mm thick cement mortar 1:3 (1 cement : 3 coarse sand)

finishing with flush pointing in white cement.

Providing and laying Ceramic tiles 6mm thick in skrting

risers of steps and dedo on 10mm thick cement plaster 1:3

(1-cement : 3-coarse sand) and jointed with white cement

(1) The whole work is to be executed through specialized

agency with a guarantee of 10 (Ten) years given on a

244 prescribed proforma duly stamped (2) The rate shall include

for work at all floors & conducting water proof test as

directed. (M.R.)

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

(B) Providing and laying integral cement based water

proofing treatment including preparation of surface as

required for treatment of roofs, balconies, terraces etc.

consisting of following operations. (a) Applying and

grouting a slurry coat of neat cement using 2.75 kg/sqm of

cement admixed with proprietary water proofing compound

comforming to IS:2645 over the R.C.C. slab including

cleaning the surface before treatment.(b) Laying cement

concrete using broken bricks/brick bats 25 mm to 100 mm

size with 50% of cement mortar 1:5 (1 Cement : 5 Coarse

sand) admixed with proprietary water proofing compound

conforming to IS:2645 ,brick bats is finally covered by

jointless cement plaster 20mm th. in C.M. 1:4 added with

special water proofing compound confirming to IS:2645 &

top smooth finished with trowel with false chequered

marking of 300 mm.size.The treatment is carried along the

vertical surface of the parapet & other adjoining wall up to

height of about 300 mm in a shape of quarter round vata

Incl. curing etc. Comp. With average thickness of 120 mm

and minimum thickness at khurra as 65 mm.

(c) The whole terrace so finished shall be flooded with

water for a minimum period of two weeks for curing and

for final test. All above operations to be down in order and

as directed and specified by the engineer-in-charge. With

average thickness of 120 mm and minimum thickness at

khurra as 65 mm. (Cement consumption 0.511 Bags / S.M.)

Distempering two coats with oil bound washable distemper

of approved brand& manufacture & of required shade on

wall surface to give an even shade over and & incl. a

priming coat of alkali resistance primer of approved brand

245 after throughly brushing the surface to give an even shade 22.00 75.84 S.M.

after throughly brushingthe surface free from mortar

droppings and other foreign matter and also including

preparing the surface even and smooth.

Apply two coats of putty and two coats of primer of

approved brand and manufacture on new wall surface to

246 give an even shade including thoroughly brushing the 22.00 40.59 S.M.

surface free from mortar dropping and other matter and

sand papered smooth.

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

247.0 specification and directions in shade and colour approved 33.00 82.00 S.M.

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Water preparation:

Prov. & Fixing S.W. Gully trap with C.I.grating brick

masonary (C.M1:5)chamber & water tight C.I. cover with

frame of 300mmx300mm size (inside) with weight includ.

248 plastering smooth inside & outside 15mm. th' in C.M.1:3 2.00 1,098.05 No.

etc. comp. (i) Square mouth traps---(A) 100mm x 100mm

Size -P type(B) 150mm x 100mm Size- P Type

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & construction simple chamber of 23 cm. th' B.B.

Masonary in C.M 1:5 with cement plaster 15 mm th' in

C.M. 1:3 inside & outside to exposed faces, R.C.C. top slab

with 1:2:4 mix ( 1 cement: 2 Sand : 4 Grade stone aggregate

249 20mm size) ,Foundation concrete 1:5:10 & fixing C.I. cover 2.00 2,932.93 No.

with frame to be not less than 38 kg. On top etc. comp.

Inside dimension,455 x 610 mm &450 mm deep for single

Providing, Lowering & laying joining R.C.C. NP2 CLASS

Pipe In C.M. 1:1 of following nominal internal diameters

250 incl. Testing of pipes and joints etc. Comp 20.00 257.19 R.M.

(A) 150 mm. dia

Providing & Fixing C.P. Brass screw down bib tap at all

251 floor levels, polished bright etc. comp.-(A) 15mm dia. For 12.00 186.83 No.

Providing & Fixing abonite ball cock of approved qualities

directed etc. comp. (A) 25 mm. dia.

Providing & Fixing U-PVC pipe (SWR) confirming to IS

no. 13592 (Type "B") of

rince/Supreme/Jain/Astral/Tulsi/Finolex make for soil and

253 waste discharge system at all floor levels incl. All fixtures 10.00 412.00 R.M.

like bends, tees, shoe etc. jointed with resin of approved

brand & manufacture etc. comp. (M.R.) (A) 75mm Dia

Providing & fixing U-PVC pipes Confirming to IS no.

13592 (Type "A") of Prince/Supreme/Jain/Astral/

Tulsi/Finolex make for rain water at all floor levels incl.

fixtures like bends, tees, shoe etc joined with resin of

approved brand & manufacture etc. comp. (M.R.)

Providing, Laying and jointing on true line and level UPVC

pipe (SCH-40) line of Prince/Supreme/Jain/Astral/

Tulsi/Finolex make including fittings make or equivalent as

approved by angineer-in-charge. Pipe shall be fixed on the

255 wall the help of clamp at every two meter C/C or shall be

concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

Providing and fixing PVC SWR Nahni trap IS 14735 for

drain - 110x110 mm diameter with jali of the following

256 nominal diameter of self cleaning design with C.I. scread 5.00 586.27 No.

down or hinged grating including the cost of cutting and

making good the walls.

Providing erecting and fixing double coated

Sintex/Super/Reno PVC (ISI) mark water tank of required

capacity each with all necessary fittings & connection etc.

complete on terrace

Providing & Fixing Kathi around the vertical PVC drainage

pipes for concealing with cement plaster 20 mm avg

thickness(CM 1:3 [1 cement :3 coarse sand]) finishing as

per instruction given by Eng. incharge. for

(A) 75 mm PVC PIPE 7.00 173.00 R.M.

(B) 100 mm /110 mm PVC PIPE 10.00 180.00 R.M.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Store Room / Electric Room

Excavation for foundation including sorting out and

259 stacking of useful materials and disposing of the excavated

stuff up to 50 mt. lead and all lift, watering etc.comp.

(A) loose or soft soil with machineries

Providing and laying cement concrete 1:4:8 (1 cement :

260 sand : 8 graded stone aggregates 40 nominal size) and 2.00 2,769.69 C.M.

curing complete including cost of form work in :

Providing and laying ordinary cement concrete work

1:1.5:3 ( 1 cement, 1.5 sand, 3 graded stone aggregates

261 mm nominal size ) & curing comp.including cost of form

work but excluding cost of reinforcement for reinforced

concrete work in:

(A) Foundation, footing, Base of columns and Mass

Providing and laying ordinary cement concrete 1:1.5:3 (

cement, 1.5 sand, 3 graded stone aggregates 20 mm nominal

262 size ) finishing smooth curing etc. complete including cost

of form work but excluding cost of reinforcement for

R.C.C. work in: Up to G.L./P.L.

(1) Having c/s area up to 0.08 s.mt 1.00 12,844.32 C.M.

(B) BEAM:(G.B/P.B)

(1) Having c/s area up to 0.08 sq. mt. 1.00 9,102.61 C.M.

Providing & fixing IS Mark TMT Bar FE 500D

263 reinforcement for R.C.C. work incl. bending, binding & 410.00 77.29 K.G.

placing in position etc. comp. Upto G.L./P.L.

Brick work using common bunt clay buliding bricks having

264 crushing strength not less than 35 Kg./sq.cm. in C.M. 1:6 1.00 4,729.83 C.M.

(1 cement:6 fine sand ) (c) Fly Ash Bricks - Ground Floor

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each disposited

layer by ramming and watering

Filling in foundation and plinth with murrum or selected

266 soil in layers of 20cm.thickness including watering, 3.00 301.78 C.M.

ramming and consolidating etc. complete.

Providing & Applying 20mm. Th. Heavy Roller plaster on

walls or similar surfaces at all floor levels consisting of

mm av. Th. Backing coat of C.M. 1:3 (1 cement:3 sand) &

8 mm. th. Finishing coat of C.M. 1:1 (1 cement: 1 sand)

apply thick cement slurry and apply roller horizontal as well

as vartical ( two times ) up to good quality and size of grain

in elevation as per directed by engineer incharge.--- Upto

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

specification and directions in shade and colour approved

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

Surface preparation:

Surface is thoroughly clean, dry and free from all loose dirt,

chalk, grease, funfi, algae and flaking paint. This can be

achieved by brushing with a wire / stiff coir brush, followed

by water jetting if required. Fill up all minor cracks and

defects with white cement and sand mixture in the ratio 1:3.

For application on previously painted wall, previous

coatings of paint must be thoroughly scraped off and clean

the surface thoroughly using wire brushes.

Work above Plinth -

Providing & laying ordinary cement con.1:1.5:3

(1cement:1.5sand: 3 graded stone agg. 20 mm nominal size)

finishing smooth curing etc. comp. Incld.Cost of form work

but excl. Cost of reinforcement for R.C.C. Work in :

(1)Having c/s area up to 0.08 s.mt- Ground Floor 1.00 12,844.32 C.M.

(1)Having c/s area up to 0.08 s.mt- Ground Floor 1.00 9,102.61 C.M.

(3) Slabs having more than 10 cm. and upto 13 cm.

Providing & fixing IS Mark TMT Bar FE 500D

270 reinforcement for R.C.C. work incl. bending, binding & 690.00 77.29 K.G.

placing in position etc. comp.-Ground Floor

Brick work using common bunt clay buliding bricks having

271 crushing strength not less than 35 Kg./sq.cm. in C.M. 1:6 7.00 4,729.83 C.M.

(1 cement:6 fine sand ) (c) Fly Ash Bricks - Ground Floor

Providing & Applying 10mm.th.cement plaster in single

coat on brick/concrete walls similar surfaces for plastering

& finished even & smooth with a floating coat of cement

slurry mixed with admixture of lime or neeru in required

proportion etc. comp. in C.M 1:3 (1 cement : 3sand) (A)

For wall and similar surfaces - Ground Floor

(A) For wall 38.00 199.28 S.M.

(B) For ceilings and soffits of stairs 10.00 225.34 S.M.

Providing & Applying 20mm. Th. Heavy Roller plaster on

walls or similar surfaces at all floor levels consisting of

mm av. Th. Backing coat of C.M. 1:3 (1 cement:3 sand) &

8 mm. th. Finishing coat of C.M. 1:1 (1 cement: 1 sand)

apply thick cement slurry and apply roller horizontal as well

as vartical ( two times ) up to good quality and size of grain

in elevation as per directed by engineer incharge.- Ground

Providing throating or plaster drip and moulding it to

R.C.C. chajja etc.comp For all Floor

Providing 20 mm. deep finished groove in plaster in line

and level etc. complete. For all floor (M.R.)

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & laying granite slab 18mm thick in Window-

Door seal Frame Etc laid on 10mm thick cement mortar 1:4

(1 Cement : 4 Coarse sand) with nessary adhesive material

and finished with flush pointing in white or colour cement,

including rubbing & polishing comp.. (Basic Rate:-

277 Labour Charges For Edge Finished For Granite 27.00 43.43 R.M.

Providing and laying Vitrified tiles 8 to 10 mm thick, 24" x

24" in flooring treads of steps and landing laid on a bed of

12mm thick cement mortar 1:3 (1 cement : 3 coarse sand)

finishing with flush pointing in white cement.

Providing and laying Vitrified tiles 8 to 10 mm thick, 24" x

24" in skrting risers of steps and dedo on 10mm thick

279 cement plaster 1:3 (1 cement : 3 coarse sand) and jointed 2.00 1,135.80 S.M.

with white cement slurry.

Providing and fixing 35mm thick shutters for Doors,

windows and clearstory windows including anodised

alluminium butt hinges with necessary screws. (A) Indian

teak wood. (i) Fully Panelled.

Providing & fixing M.S.Grills of required pattern to

wooden frames of windows etc. At all floor levels with

M.S. flats at required spacing & frame around square or

round bars with round headed bolts & round eaded bolts

and nuts or by screws incl. Priming coat of Red lead paint

etc. comp. (A) Plain grill For all Floors

Providing and fixing window having extruded aluminium

Powder Coated section frame main outer size 63.50 x

x1.95 mm (of Jindal section no.4605, @ Wt. 1.094Kg/mt)

horizontal Two track member size 61.85 mm x 31.75 mm x

1.20 mm (of jindal section no:8687, @ Wt. 0.695 Kg/mt.)

vertical member of size 61.85 mm x 31.75 mm x 130 mm

(of jindal section no:8758 @ wt. of 0.659 kg/mt) with

282 sliding shutters of horizontal member size 40 mm x18 mm x 3.00 1,705.67 S.M.

1.29 mm ( of jindal section no:8949, @ Wt. of .456 Kg/mt)

vertical member of size 40 mm x 18 mm x 1.29 mm (of

jindal section no:8947, @ Wt. of 0.456 Kg/mt/section

@ Wt. of 0.457 Kg/mt) with 5 mm thick tranparent bronze

colour tineted float glass with powder coated aluminium

fittings and fixtures and transparent silicon sealant glass

fixing to frame as per details etc. complete for window.

(1) The whole work is to be executed through specialized

agency with a guarantee of 10 (Ten) years given on a

283 prescribed proforma duly stamped (2) The rate shall include -

for work at all floors & conducting water proof test as

directed. (M.R.)

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

(B) Providing and laying integral cement based water

proofing treatment including preparation of surface as

required for treatment of roofs, balconies, terraces etc.

consisting of following operations. (a) Applying and

grouting a slurry coat of neat cement using 2.75 kg/sqm of

cement admixed with proprietary water proofing compound

comforming to IS:2645 over the R.C.C. slab including

cleaning the surface before treatment.(b) Laying cement

concrete using broken bricks/brick bats 25 mm to 100 mm

size with 50% of cement mortar 1:5 (1 Cement : 5 Coarse

sand) admixed with proprietary water proofing compound

conforming to IS:2645 ,brick bats is finally covered by

jointless cement plaster 20mm th. in C.M. 1:4 added with

special water proofing compound confirming to IS:2645 &

top smooth finished with trowel with false chequered

marking of 300 mm.size.The treatment is carried along the

vertical surface of the parapet & other adjoining wall up to

height of about 300 mm in a shape of quarter round vata

Incl. curing etc. Comp. With average thickness of 120 mm

and minimum thickness at khurra as 65 mm.

(c) The whole terrace so finished shall be flooded with

water for a minimum period of two weeks for curing and

for final test. All above operations to be down in order and

as directed and specified by the engineer-in-charge. With

average thickness of 120 mm and minimum thickness at

khurra as 65 mm. (Cement consumption 0.511 Bags / S.M.)

Distempering two coats with oil bound washable distemper

of approved brand& manufacture & of required shade on

wall surface to give an even shade over and & incl. a

priming coat of alkali resistance primer of approved brand

284 after throughly brushing the surface to give an even shade

after throughly brushingthe surface free from mortar

droppings and other foreign matter and also including

preparing the surface even and smooth.

(A)Wall 38.00 75.84 S.M

(B) For ceilings and soffits of stairs 10.00 84.37 S.M

Applying Priming coat over new steel and other metal

surface after over and including preparing the surface by

285 throughly cleaning oil, grease dirt and other foreign matter 2.00 36.74 S.M

and scoured with brushed fine steel wool, scrapers and sand

paper with ready mixed priming paint brushing red lead.

Painting two coat (excluding priming coat) on new steel and

other metal surface with synthetic enemal paint, burshing to

give an even shade including cleaning the surface of all dirt,

dust and other foreign matters.

Providing and applying two coats of weathershield max

paint (3 coats may be required in case of darker colours) of

ICI Dulux or Apex Ultima of Asian paint including

applying exterior acrylic primer coat as per manufacturers

287 specification and directions in shade and colour approved 70.00 82.00 S.M

by architects, on exterior surfaces of the building including

scaffolding, preparing the surface, watering, curing etc.

complete and as directed by the architects and

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Steel work welded in built up sections, framed work

288 including cutting,hoisting, fixing in position and applying a -

priming coat of red lead paint

(A) in beams & joists channels angles, tees, flats with

connection plates orangle cleats as in main & cross 20.00 9,108.48 Qtl.

beams,hip & trussed purlins connected tocommon raffers &

Civil Work Amount

ELECTRIFICATION WORK OF BUILDING

INTERNAL WIRING

Point wiring for Light / Bell with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to

10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame covered

with textured/metallic/white front plate modules erected on

/ in wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

2 (For point wiring in bathroom and W/C and washbasin area 0 224.73 Pt. -

in residential quarters reduce overall rate by 50% of point

wiring for light.)

Point wiring for secondary light point with 2-1.5 sq.mm

& earth wire of 1.5 sq.mm (green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand copper

wires, in below type of pipe to be erected complete with

earth continuity and necessary connection with primary

light with accessories erected on Metal / PVC / wooden

box covered covered with appropriate front plate modules

2 erected on / in wall / ceiling for open / concealed wiring. 0 151.50 Pt. -

with necessary Lamp holder / ceiling rose / H.D.Connector

as directed.as per pipe erected with following type of

Note:- Maximum up to 6 mtrs length, excess will be

considered as Mains for Secondary Point.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete

Point wiring for FAN with 2-1.5 sq.mm & earth wire of

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade

FRLS PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected with 6A Modular

type switch and hum free EME step type electronic fan

regulator mounted and accessories with earth continuity of

3 following type erected on PVC / Metallic/Wooden box, 3 629.23 Pt.

single mounting base frame covered with

textured/metallic/white front plate modules erected on / in

wall / ceiling as per pipe erected. with necessary ceiling

rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete, Cat. III

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected

with following type of accessories.

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu.

Wire from nearby switchboard/mcb db board

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete, Cat. III

Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected

with following type of accessories.

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm

Cu. Wire from mcb db board.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete, Cat. III

Point wiring for Individual Plug with & earth wire both

are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of

pipe erected complete with Modular type switch & 5 pin

Plug erected on PVC / Metallic/Wooden box covered with

appropriate front plate modules erected on / in wall / ceiling

as per pipe erected with following type of accessories.

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm

Cu. Wire with 2.5 sq.mm ( green) earthing wire from mcb

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete, Cat. III

Point wiring for on board Looped Plug with 6A Modular

type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame covered

with textured / metallic/white front plate modules erected

on / in wall / ceiling with following type accessories, Cat.

Point wiring for Two Way Controlled Light Point with

2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of

.ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires erected in below type of pipe with 6A

Modular type switches and following type of accessories

erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate modules erected on / in wall / ceiling as per pipe

erected. with necessary batten/angle holder or ceiling rose

or H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete, Cat. III

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

but for 2 nos of 2.5 sq.mm FRLS PVC insulated copper

conductor wires with 1 no 1.5 sq.mm FRLS PVC insulated

conductor wire (Green color for earthing) for 16 A AC

starter with universal socket up to satisfaction of E.I.C.

(Excluding Main Line, including 16A AC starter & Socket)

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate , modules erected with necessary connections as per

site situation directed by Engineer In charge.

(3) Two Pin/RJ-11 Telephone Socket

[A] For One Gang, Cat. III 0 153.52 Ea. -

[B] For Two Gang, Cat. III 0 200.99 Ea. -

(4) TV Co-axial Socket outlet, Cat. III 0 153.52 Ea. -

(7) Blank Plate Single, Cat. III 0 24.24 Ea. -

(8) Computer RJ-45 socket, Cat. III 0 153.52 Ea. -

(22) 16/20/25 Amp. Modular Starter for Motor / A.C. Unit

Complete, Cat. III

(19) Modular Indicating Call Bell, Cat.III 0 314.11 Ea. -

(20) Modular Buzzer, Cat.III 0 143.42 Ea. -

Providing and erecting ISI mark Medium class RIGID

PVC PIPES of following size complete to be erected on/in

wall or ceiling erected with necessary PVC fittings &

11 Junction boxes fixed with adhesive solution & Clamps with

following dia of pipes, in approved manner as directed.

Providing & erecting PVC Corrugated Flexible Conduit

with required nos. of coupling, PVC bushes, Check-nuts

12 etc. complete of following sizes.

Supplying & erecting UPVC Mini trunking (PVC Casing-n-

Capping) having double-locking arrangement with grooves,

trunking of size not below 12.5 mm in height as per IS with

13 accessories of PVC/Resin polypropylene not below 1.8 mm thick

duly sealed in joint & erected on wall / ceiling of following size .

Providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor wire

in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper conductor

14 FRLS PVC insulated stranded wire of green colour for earth

continuity of following size

(A) With medium class Rigid PVC pipe and accessories

(a) 2 wire 1.5 sq. mm 150 59.59 Mtr.

(b) 2 wire 2.5 sq. mm 120 78.78 Mtr.

providing and erecting Mains with 1.1 KV grade FRLS

PVC insulated ISI marked stranded Copper conductor wire

in following type of pipe to be erected in / on wall / ceiling

with 2.5 sq. mm copper conductor FRLS PVC insulated

15 stranded wire of green colour for earth continuity of

(A) with medium class Rigid PVC pipe and accessories

(a) 2 wire 4 sq. mm 10 107.06 Mtr.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

(d) 3 wire 4 sq. mm 10 136.35 Mtr.

Providing & Erecting approved make following size of TV

Co-axial flexible cable comprising inner conductor of

solid bare copper insulated with Foam PE & Secondary

16 conductor made of poly - Aluminium film bonded Al.

Braids @ suitable coverage overall sheathed with black

PVC insulation.

Supplying & erecting approved make Telephone Cable

electrolytic copper conductor PE insulation twisted in

two pairs, & wrapped with FRLS PVC tape & sheathed

with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in

existing pipe. of following size of conductors & nos.of

pairs. With necessary connections.

[A] Conductor Size 0.5 mm

(2) Two Pairs 0 19.19 Mtr. -

(b) Armoured [Jelly Filled]

(1) Ten Pairs 0 120.19 Mtr. -

(2) Twenty Pairs 0 190.89 Mtr. -

(3) Fifty Pairs 0 446.42 Mtr. -

Supplying & erecting approved make LAN cable of

following size in existing pipe as per direction [C] CAT -

Providing & erecting main Distribution (MDF) indoor

type, back mounted frame as per DoT standard approved

with krone strips

(a) Suitable for 10 pair 0 949.40 Ea. -

(b) Suitable for 20 pair 0 1,311.99 Ea. -

(c) Suitable for 50 pair 0 1,678.62 Ea. -

Supplying & erecting M.S. Box having 16 Gauge painted

with red oxide or Heavy duty PVC box erected flushed on

wall or concealed in wall with necessary plastering &

finishing as directed of following size.

Providing & erecting Switch board for Computer or

electric apparatus consisting of following items in single

board erected on PVC / Metal/Wooden board

concealed/open with 3 mm thick PC (Polycarbonate) /

21 Acrylic sheet erected as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories, Cat. III 0 1,081.71 Ea. -

Decorative call bell Ting-tong box type 250 volts

complete erected

L.T. SWITCHGEAR AND DIST. BOARD & L.T. PANEL

Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of

KA. at 415 V,having normal current rating up to 25 A to

23 100A. with Fixed thermal & magnetic release suitable to 1 6,173.12 Ea.

work on A.C. supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing

G.M.S. housing.

MCB single pole 6A to 25A, 10 KA Cat. III (10

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing & erecting 240 V MCB double pole switch for

motor & inductive load (C Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in existing box

having following capacity, Cat III, (A) 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch for

lighting Load (B Curve) having 10 KA breaking capacity

& confirms to IS : 8828 in existing box having following

capacity, Cat (III), 6 to 32 Amp.

27 MCB, 10 KA, 40 Amp., FP, Cat. III (INCOMER) 2 638.32 Ea.

Providing & erecting 415 V MCB Four Pole for Motor

& Inductive Load (C Curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having

following capacity, Cat III, 6 to 32 Amp.

Supplying & erecting approved make Electronics Starter

and relay for air conditioners in ABS plastic moulded

housing. Company fabricated with bakelite terminal for

connection with silver coating bimetallic contact in

switching device for o/p with following features.

29 (1) Low Voltage Protection below 130 V 1 886.78 Ea.

(2) High Voltage protection above 270 V

(3) Overload protection for 2-5, 4-10, 8-14, 10-16, 14-22

Amp. (inverse time chara-)

(4) Indicating LEDs for AC on LV, HV, O/L, T/D

(5) With unique feature of 3 minute of time delay

Plastic enclosure fitted with DIN rail suitable for

incorporating One / Two nos. MCB

Plastic enclosure fitted with DIN rail suitable for

incorporating Three /Four nos. MCB

Sheets steel powder coated enclosure suitable for

incorporating One/Two nos. MCB.

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase

(b) sheet steel double door (IP-43)

(ii)4 way 2 629.23 Ea.

(iii)8 way 2 1,152.41 Ea.

(B) three phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI)

(b) sheet steel double door

RCCBs, 30 mA, 10 KA, 25 Amp., DP, Cat. III

Providing and erecting metallic vitrified danger notice

board as per language suggested by engineer incharge for

MEDIUM VOLTAGE installation to be erected as per IS-

Providing & erecting Medium Voltage Danger Notice

36 Board sticker as per language suggested by engineer 0 26.26 Ea. -

incharge of standard size as per IS-2551

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

providng and erecting Approved make single phase

electronic energy meter rating 5A/20A/40A based on

ASIC (Application Specific integral circuit) digital

technology with accuracy Class-I, temper proof, free from

37 effect of external magnetic field with phase, earth, reverse 0 1,738.21 Ea. -

and impulse indications, 6 digit electro-mechanical counter

suitable to work on 120 V to 300V, 45 - 55 Hz., housed in

robust enclosure complete to be erected as directed with

year replacement guarantee. Cat. III

providng and erecting Approved make energy meter

phase 4 wire unbalanced load rating, 10A to 60 Amp.

based on ASIC(Application specific Integral Circuits)

digital technology with accuracy Class - 1 , temper proof,

38 free from effect of external magnetic field with 3 phase 0 2,696.70 Ea -

indication, earth & impulse indication, 6 digit electro

mechanical impulse counter, suitable work on 120 V to

300V per phase 45-55 HZ, housed in robust enclosure with

erection as directed. Cat. III

INDOOR LIGHTING ITEM

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die

cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V,

Power Factor more than 0.9, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

39 Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

(i) 5-10 Watts, Surge-2 KV, IP-20, conventional 1 to

(iii) 18-20 Watts, Surge - 2KV,IP-20, conventional 4 feet 34 295.93 Ea.

(iv) 22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet 0 373.70 Ea. -

(v) 36-40 Watts, Surge-2 KV, IP-20, conventional

Supplying and erecting LED lamps with following wattage

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp

40 holders, pf >=

(A) LED Lamps integral type, with PC diffuser suitable

LAMP holder, Cat. III

(i) 2 to 3 watts 0 69.69 Ea. -

(ii) 5 to 8 watts 4 112.11 Ea.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body

with company mark/name

160V to 270V,Power Factor more than 0.9, THD < 15 %,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

41 Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount

Downlight with provision for spring loaded mounting clips

(ii) 11-15 watts, Surge-2 KV, Cat. III 0 427.23 Ea. -

(iii) 16-20 watts, Surge-2 KV, Cat. III 0 589.84 Ea. -

(iv) 22-24 watts, Surge-2 KV, Cat. III 0 758.51 Ea. -

(B) LED Panel Light with provision for Plane front frame

with translucent cover fixed to housing complete.IP20

(vi) 36 watts, 24" x 24", Surge- 2KV, Ct. III 0 1,794.77 Ea. -

Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with

toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD <

%, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

42 efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(

fittings required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral

and ,Light must have 440VAC line supply with over-

voltage protection.

(iv) above 90 to 120 watts, Cat. III

(Wall mounting outside)

Supplying and Erecting Of L.E.D. type High bay fixture

having Power Consumption of following watts with, Input

Voltage 110 - 290 V.AC with full efficiency, Power Factor

> 0.9 with 50/60 HZ, CCVC LED Driver used for

maximum power saving, Best Quality luminium alloy

housing and aluminium Dome for etter heat dissipation,

CCT Cool white (6000K), CRI 80, Beam angle >

dgrees, working temperature -20 degc to +55 degc, Body IP

FAN AND RELEATED ITEM

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Supply, Installation, Testing and Commissioning of suitable

sweep, BEE 5 Star rated, Ceiling fan with Brush Less

Direct Current (BLDC) permanent ferrite magnet Motor,

class of insulation: B, Rust free 3 nos.Aluminium blades,

nos. canopies, shackle kit with earthing provision, copper

winding, Power factor not < 0.9, Service Value (CMM/W)

minimum 6.85, Air delivery minimum 215 CMM,

RPM,230v (tolerance as per IS : 374-2019), THD < 10%,

compitible with electronic regulator unit for Speed Control

and all remaining accessories including safety pin, nut bolts,

washers, temperature rise = 75 degree C (Max.), suitable

for 140 to 285 Voltage and rectifier circuit with surge, over

current and overload protection , 50 Hz, Single phase AC

Supply, earthing etc. Complete as required.[ Make shall be

approved by Engineer in Charge]

(A) 1200 mm Sweep (48")

Providing & erecting Approved make Ceiling Fan with

double ball bearing ISI mark with Condenser 230 volt

A.C.50 Hz 1200 mm sweep complete having 3 blades

aluminium body and blade sets having ornamental design

shanks , canopy erected with earthing. [ Make shall be

approved by Engineer in Charge]

Providing & erecting Approved make Power Saving

Watt Ceiling Fan with double ball bearing ISI mark with

Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete

having 3blades with aluminium blades with , canopy &

cm. down rod erected with earthing.(Make shall be

approved by Engineer in charge))

Supplying and erecting 19 / 20 mm. nominal bore Medium

Class M.S. Pipe down rod erected duly painted for fan

complete with proper insulation without leakage and

Supplying & erecting fan hook box of 10 mm M.S. round

bar bounded to the RCC bars up to 50mm length each side

47 and pierced through a 16 Gauge M.S. box / Heavy Duty 3 108.07 Ea.

PVC box complete erected concealed in Ceiling with

necessary finishing.

Providing 2.5mm.thick laminated acrylic sheet to cover

the fan hook or Fan box.

Supplying & erecting single phase approved make

industrial exhaust fan suitable for medium duty ring

49 mounted low noise operation suitable for medium duty 6 2,054.34 Ea

having following dia size and maximum speed in RPM

[A] 305 mm dia 900 RPM, Cat. III

Providing suitable M.S. louver shutter of the Exhaust

Supplying & erecting electro galvanised G.I. wire micro

mesh jali cover of grade 304 required size with suitable

wooden frame duly fitted in wall outside of exhaust fan for

insect protection.

Providing & erecting fresh air fan 250 mm dia with

square frame make of ABS body with louvers, Cat. III

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Supplying and erecting approved make oscillating type

medium duty bracket fan with Aluminium Blades A.C.

23OV. 50cy/s, with thermal overload protection wall

mounted with height adjustment and rotary tilting device

complete with guard, pull cord for speed and oscillation

flexible Core plug top complete erected with lead wires as

EARTHING SYSTEM

Providing and erecting required size HOT deep

Galvanised iron strip for earthing of H.T. , OCB/ ACB/

Transformer LT panel board, Motors etc. using proper

Providing and erecting Annealed bare Copper wire 8 to

Providing and erecting HOT deep Galvanised iron strip

wire 8 to 16 SWG.

Providing and erecting Pipe type earthing having

cms. long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

Providing and erecting Pipe type earthing with 40 mm

dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling

buch buried in specially prepared earth pit & G.I. earth wire

of 8 SWG erected & connected as directed

For using salt and charcoal / coke as required for pipe

Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 80 mm having 80-200 Micron galvanising,

Inner pipe dia of 40 mm having 200-250 Micron

galvanising, connection terminal dia of 14 mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for

following type of applications with chamber and heavy

duty cover.(approved make OEM has to submit test

certificate including value of earth resistane of installation.

[B] For Electrical installation up to 11 KV located in other

than normal soil i.e. Soft Rock, Marshy Soil etc.

-Length of Pipe : 2 mtr 1 7,095.25 Ea.

-Back filling Compound :1 no. Bag of 25 Kg. two for body

earth and one for neutral earth

[C] For Electrical Installation covering Transformer

Neutrals, Lightning arrester Earthing, A.C.Plant &

Sensitive Computer System(like Automation,

SCADA)i.e. independent Earthing located in other than 1 10,593.89 Ea.

normal soil i.e. Soft Rock, Marshy Soil etc..

-Length of Pipe : 3 Mtrs.

-Back filling Compound :2 nos Bags of 25 Kg.

CABLES, WIRE AND TERMINATIONS

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (From

DISCOM energy meter to Main L.T. panel)

(G) 3 1/2 core 150 Sq. mm ( 70 Sq. mm 1/2 core) 0 726.19 Mtr. -

Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in existing

trench / pipe at road crossing or floor of following size of

(A) 3 1/2 core 25 Sq. mm ( 10 Sq. mm 1/2 core) 0 1,345.32 Mtr. -

Making trench in soft soil of suitable width of 90 cm deep

for laying cable or locating the fault all over the run and

back filling the same and making the surface as normal

Providing & laying. R.C.C. Hume pipe for cable to be laid

90 cm. below ground across the road crossing or on floor

with necessary material in an approved manner and making

the ground as per original. (F) 100 mm dia.

Providing & laying approved make Double walled

corrugated pipes (DWC) of polyethylene(conforming to

IS 14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of

cable. below ground / road surface for enclosing cable,

(A)50 mm outer dia

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand / Solid Copper conductor for 1.1 KV.

to be laid on wall with necessary clamps or in existing

trench / pipe at road crossing or floor of following size of

(A) 4 core 2.5 Sq. mm 0 269.67 Mtr. -

(B) 4 core 4 Sq. mm 0 362.59 Mtr. -

(C) 4 core 6 Sq. mm 10 508.03 Mtr.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Copper conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe at road crossing or floor of following size of cables.

(A) 4 core 10 Sq. mm 0 673.67 Mtr. -

(B) 4 core 16 Sq. mm 0 984.75 Mtr. -

Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables.

(B) 2 to 4 core 6 Sq. mm 5 38.38 Ea.

(C) 2 to 4 core 10 Sq. mm 10 38.38 Ea.

(D) 2 to 4 core 16 Sq. mm 0 47.47 Ea. -

(E) 2 to 4 core 25 Sq. mm 0 51.51 Ea. -

Providing and, fixing heavy duty flange type brass

double compression type cable gland with rubber ring

for PVC insulated armoured cable complete with out going

tails, insulating tape etc for following size of cables.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Solder less crimping type Aluminium lugs conforming to

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

Solder less crimping type Copper lugs conforming to IS

suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

WATER COOLER AND PURIFIER

Providing and erecting water cooler having storage

capacity 80Ltr. & cooling capacity 40 Ltr.per hour @ an

ambient temp of 45˚ C. The outlet temp. of the water should

drop by 15˚ C within a hour, The water cooler should be

72 comprising of hermetically sealed compressor, fan motor, 0 41,342.33 Ea. -

condensing unit, water tank surrounded by evaporating coil,

thermostats, relay etc. complete with necessary inlet &

outlet connection. The body of water cooler will be made

from Stainless Steel.

SITC of Water Purifire Eureka Forbs Make AG 200 or

Supplying & erecting bank of all polypropylene condenser

(APP type) with standard capacity of 2,3,5,7, 10,12.5 &

KVAR units of P.F. correction for operation on 3 phase

c/s, 400 /440V (+ / - 10%) with externally discharging

resistance, earthing terminal & built on angle iron of

channel iron frame work and provided with terminal cover

box. Complete erected on provided iron bracket or on floor

duly tested by license.

PUMP SETS AND STARTERS

Providing & erecting open well type horizontal mono

block pump set with stainless steel body having following

(D) 1 HP Three phase open well motor pump set suitable

for 190 LPM discharge @ 21 mtr. head, suitable for 32mm

dia. delivery pipe.

Supplying submersible pump set suitable for bore of

mm. dia. or more having three phase motor capacity not

more than 3 H.P. of different range with following capacity

(A) (20 stage) 170 to 185 LPM discharge at 57 to 48 mtrs.

Respectively head suitable for 50 mm dia. delivery pipe,

Supplying & erecting approved make self-priming

domestic monoblock water pump with 1 H.P motor,

suitable for operation on 230 volts, 50c/s. AC supply with

77 metallic flange, and M.S. impeller delivery and following 1 7,679.03 Ea.

(a) 40 LPM at 24 mtrs. head suitable for 25mm dia.

Delivery. Cat.III

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

Supplying and erecting push button operated fully

automatic Star-Delta starter with 3 Nos. of 15A.rating

contactors and directly operated thermal overload relay

having 10-21A range and erected in sheet steel enclosure

for 3 phase 415V. 50 c/s. A.C. motors from 7.5 to 15H.P.

complete erected on

(A) P.W. Block with necessary connection, Cat.III 0 9,758.52 Ea. -

(B) Angle iron frame add to the above 0 184.83 Ea. -

Supplying and erecting Direct On-line Electronics Starter

with 2-5/4-10/8-14/10-16 Amp. Rating relay (variable

current setting) directly operated in totally insulated elegant

enclosure and 18 Amp. Rating power relay with start - stop

button for single phase operation up to 3 HP as per

79 complete erected on P.W. Block with following features. 1 1,603.88 Ea.

Low voltage cut off below 140 V

High voltage cut off above 280 V

Overload protection

Indicating LEDs for motor on lv, hv & overload tripping.

Supplying and erecting Direct-on-line, Starter with

15A.rating contractor and with 4-14A. range, directly

80 operated thermal overload relay in sheet steel enclosure for 0 2,046.26 Ea. -

3phase 415V.50 c/s. A.C. motor up to 7.5 H.P.complete

erected on P.W. Block with necessary connection. Cat.III

Supplying & erecting approved make Automatic liquid

level controller 6A. with sensor testing as per instruction

81 of Engineer in charge on site complete with wiring 0 2,355.32 Ea. -

connection with existing wires , with copper conductor

from pump to upper and lower tank.

Supplying & erecting 20 Amp 10 KA ‘C Curve’ single

pole MCB with 20 Amp. Plug socket, company fabricated

powder coated sheet steel enclosure erected as directed with

[A] Metal Clad Socket with metal clad top. Cat.III 0 527.22 Ea. -

[B] 15 Amp. / 5 Amp. Five pin Universal Socket Cat.III 0 660.54 Ea. -

Supplying and erecting, commissioning and testing of

Diesel Generating set confirming to IS: 4722:1968 &

BS:5514 having continuous rating, 3 phase, 415 volts,

cycles A.C. supply comprising of a totally enclosed

air/water cooled diesel engine with multi-cylinders

developing suitable BHP not less than following capacity

at 1500 RPM with 10% overload for one hour in 24 hours

with standard accessories like fly wheel, lubricating oil

cooler, "A" class governor, heavy duty fuel wheel and

lubricating oil filter, oil bath air filler, lubricating oil

pressure gauge, end exhaust manifold, standard set of tools

with adjustable spanners, screw drivers, cylinder head to

cover, joint cylinder head to exhaust, element lube oil filter,

12 / 24 volts electric starting equipment complete with

standard heavy duty battery, dynamo, cut-outs, ammeter,

necessary wiring, pressure gauge, starter etc and heavy duty

Residential type exhaust silencer and vertical hot air duct

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

logged with asbestos rope, save oil trays, exhaust piping of

required length, standard wall/floor mounted fuel with level

indicator and piping and drip proof alternator, self excited,

self regulated, screen protected, with excitation system,

capable of delivering the rated system output at 415 volts,

phase, 0.8 PF, 50 Hz, 4 wire, running at 1500 RPM,

conforming to IS-4722- 1968 with voltage regulation +/-

83 5% of rated voltage from no load to full load. Both the

engine and alternator fitted on a common fabricated steel

base plate with antivibration mounting engine and

alternator both connected to each other by flexible flange

coupling and with floor/wall mounted control panel box

comprising of voltmeter ammeter, selector switches, ACB

/ MCCB / MCB of adequate capacity,

indicator lamps duly wired with HRC fuses. The alternator

& control panel shall be connected with provided suitable

capacity armoured cable and complete with Acoustic

enclosure (canopy) made out of 16 SWG CRCA Sheet,

sound absorbing material Rockwool of 64 density &

mm thick conforming to IS:8183 / PU Foam of 40 Density -

at least 40 mm. The resin bonded rockwool covered from

inside the canopy by perforated sheet with 3/4 mm holes,

sound level not more than 75 dB at a distance of 1 mtr, as

per PVCT norms. Erection, commissioning and satisfactory

testing as per requirement with first filling of fuel, oil, etc.

with guarantee / Warrantee of complete system for Two

years. & with obtaining all necessary certificate from

Electrical Inspector. The Capacity and Ratings of DG sets

(H) Continuous Rating of 50 KVA ,BHP not less than

(I) Continuous Rating of 62.5 KVA ,BHP not less than

Providing & erecting approved make AMF control panel

suitable for following size of 3 phase, 415 V., 50 cycles,

A.C. diesel generating set complete of scope as detailed

1) Power module: A pair of electromechanically

interlocked contactors (for mains & generator) Overload

relay for generator contactor Neutral contactor for mains

and generator Power socket for connections.

2) Control and metering module: Line voltage monitor.

Generator voltage monitor Ammeter 3 items attempt start

facility. Air circuit breakers/MCB/MCCB of suitable rating

for auto/manual operation. Auto/manual switch. Emergency

stop push buttons. Manual start push button. frequency

meter. Engine hour meter. Two earthing studs.

3) Protection module: The engine shutdown in the unlikely

event of Low lube oil pressure High cylinder head

temperature. V belt failure.

4) Indicators with alarm Load on generator.

5) Indicators Load on mains Engine fails to start .

Emergency stop battery charger.

The AMF Panel of following capacity

(A) AMF Control Panel for 50/62.5 KVA 3 phase DG Set 0 97,320.57 Each -

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

(A) GENERAL DESCRIPTION OF LIFTS.

[1] GEAR LESS LIFT DRIVE (MRL) comprising of

High Starting torque Lift 3 phase 440 V A. C. Permanent

Magnet Synchronous motor of proper rating with high

efficiency shall be used.[2] Micro processor based / PLC,

ACVVVF, vector control drive with encoder feedback

closed loop system shall be used for lift car and door

operation which shall be full collective selective operation

hall call demand response, UP/DOWN hall stops, Main,

Up/ Down Contactor with overload and phase reversal

relay and safety controls.

[3] Car with M S platform with bracings of adequate size

and to sustain the impact load cabin + passenger with safety

factor of fire for steel and side panels of Stainless steel of

sheet of grade 304 duty. Car ceiling will be S.S. finishes

with aesthetic appearance with LED ceiling lights. Car

flooring shall be of anti skid PVC with choice of colour of

engineer in charge. Car doors shall be of stainless steel

grade 304, hairline finish with centre opening / telescopic

automatic doors. Car panel will also be S.S. 304 finished

with emergency stop device, mechanical door safety device,

facility of auto/ attended mode. All car panel buttons and all

floor switches must be with brail language as per lift act.

[4] All landing doors must be fire rated for 2 hour shall be

fully automatic centre opening/ telescopic opening made of

hairline finish steel grade of 304 with key holes and

infrared curtains with Unlocking facility from outside

[5] Appropriate battery operated emergency light in the car

along with alarm switch shall be provided. Also,

Emergency Light & Fan should start immediately without

any Time Delay as soon as power fails.

[6] Digital scrolling indicator system for up-down arrow

along with floor position indicator shall be provided inside

the car and at all floors.

[7] Full height infra red curtain with multiple cross /

crossing light beams shall be provided.[8] Automatic

Rescue Device (ARD) shall be provided accordingly of

passenger capacity with Manual Rescue Operation (

Manual Cranking Facility).

[9] Audio visual indication in the lift car showing over

loading shall be provided such that doors kept open till

excess load is removed.

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with automatic sleep

timer shall be provided.

[12] Voice annunciator with suitable music shall be

provided in lift car.

[13] Self diagnostics system for operational and safety

parameters shall be provided in control panel.

[14] Mechanical over speed governor with governor

calibration as per actual site parameters and submission of

calibration certificate submission, door key holes in the

floor doors, fireman switch shall be provided.

[15] Lift machine hoisting arrangement in the lift machine

room and monkey ladder for lift pit should be provided by

the lift agency, along with the other steel structure works,

foundations for the machine etc…

[16] In the hoist way fascia plate shall be provided without

any extra cost, where ever required as / if directed by

engineer in charge.

[17] Permanent wiring with necessary safety devices like 23,39,503.40 Ea. -

85 RCCB in all circuit, Over Voltage Under Voltage protection

and THD eliminator in circuit for lift machine room and lift

well with proper numbers of light points, with fixtures,

exhaust fan and plug points shall be provided by the

agency. Only 3 phase Power Supply shall be made

available by department in lift machine room. Necessary

Earthing as per Lift Act/Rules shall be arranged by Lift

[18] Any civil/ electrical works for additional and alteration

in lift shaft and machine room related to erection of lift

shall be made by lift agency without any extra cost.

(granite/marble fixing around all landing door openings are

not in lift agency’s scope.)

[19] Agency has to provide all working drawings and

documents and liaison services for obtaining all necessary

permission from lift inspector and other authorities.

[20] acrylic transparent licence/display A4 size holder in lift

[20A] As per statutory requirement of Govt. Of Gujarat lift

& escalator act 2000, lift agency has to provide

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection during/after lift

erection and provide report by third party authorized by

concern licensing authority

5.agency has to provide third party insurance upto

completion of free maintenance period and submit the

document for the same.

[21] Car Panel Operating Buttons with floor position

indicator/buttons must be of Auto Glow type clearly visible

when view from inside cabin.

[22] For Physically Handicapped person Full Length

Handrails of hairline finish steel grade of 304 should be

provided at appropriate height on the Rear & Side Wall

Panels in Lift Car.

(B) SPECIAL FEATURES DESCRIPTION OF LIFTS for

PREMIUM category

(Without GST & With Cess)

Description Qty. Rate per Amount (Rs.)

1. Advanced control system dual 64 bit embedded

microprocessor with CANBUS Serial Communication

mode including Regenerative power efficient operation,on

site programming facility, Anti nuisance, Pte-opening,

BMS/RMS with necessary online real time monitoring

system having necessary connectivity for remote monitoring

& other suitable supporting hardware & software devices to

fulfil the purpose.

2. Floor Indication LCD Display with call registration &

brail mark with arrival gong and hall lantern & TFT Screen

in the car with MP3 Voice Announcer.

3. CAR Panel should be Scratch resistive SS Moonrock

finish / Hair Line / Honeycomb for car and all Doors, All

landing doors must have fire rating up to 2 hours and car

door must have multi-level crisscross beam door protection.

4. To & fro communication system & wiring (i.e. car

control room & guard room ) and Each elevator are

equipped with remote monitoring system.agency has to

provide mobile app and user id and password for

15/16 Passengers, Ground plus 2 upper floor with Rated

Speed of 1.0 m/sec., (strecher lift)

(C) With General PLUS ADDITIONAL SPECIAL

FEATURES attached herewith. Prem. Cat.

INVERTOR STABILIZER

Supplying and erecting of 1850VA Sine wave Digital

Inverter systems.

Supplying and erecting of 12V/150AH Tubular battery

for 1 hrs battery backup.

88 Supplying and erecting of 1KVA Stabilizer. 0 10,225.64 Ea. -

Supplying and erecting approved make online Un-

interruptible Power Supply system comprising flat cum-

boost charger, static Inverter & sealed maintenance free

SMF batteries. The charger having operating capacity for