SPECIAL REPAIR TO OTM BLDG NO P-209 (C COY OR LIVING) AND BLDG NO

Amount

Taking down chowkats or frame with shutters ( without taking off shutters from the frame) n.exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 sqm each complete all as specified and directed.

S&F 2nd hard wood factory made 35mm thick glazed, and skeleton shutters open rebated & prepared to receive, glass, gauge etc. divided into squares with plain chamfered or rounded mitred and rebated any numbers and size of members of shutters as specifed in SSR Part I, Section 8, clause 8.24(a); supplied and fitted to chowkahts complete all as specified and directed.

S&F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F mild steel angle iron work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe290 (Gde-E-165)

S&F Stainless steel butt hinges medium weight 100mm long complete all as specified and directed.

M&L for 150mm long extructed aluminium handle fabricated type complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section 150 mm size complete all as specified and directed.

S&F aluminium alloy anodised sliding door bolt with hasp and stapple ( bolt type) and fixing clips of sheet cast or extruded section with fixing bolts and sliding bolt of extruded section 300mm length & dia not less than 12mm with & including 6 Nos of bolts complete all as specified and directed.

S&F factory made solid PVC door, cup board shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded both side prelaminated PVC 'C' channel having a prelaminated PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & b PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail, lock rail & bottom rail panelling of both side prelaminated PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specification & diagram/product drawing shown on ser page No 156 of SSR Part II complete all as specified and directed & directed

S&F solid PVC door, cup board frame size 50mmx47mm made out of 5mm prelaminated PVC sheet reinforced with MS square tube all as per specification and as per drawing shown on ser page No 150 of SSR Part II (for item 884) complete all as specified and directed and directed

S&F Stainless steel wire cloth 0.36mm normal dia of wire and average width of aparture 1.40mm and fixed with tinned tacks or Stainless steel wire stapples complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M & L for providing cement concrete type C-1 1:3:6 using 20mm graded stone aggregrate in lintles up to 1.50m clear span, cills, steps, seismic and other bands, plinth courses, string courses,lacing courses, parapets and railings upto 60cm in height, copings,kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering, slightly rounded or chamfered angles and throating as directed including form work complete all as specified.

Hacking out old broken glass (any thicknesss, size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

Taking down steel windows and ventilators with frame (without taking off shutters) complete area not exc 1.5 sqm and removing from site of work all as directed by Engineer-in-Charge.

S&F steel windows with side hung shutters glazed or gauged including projection type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welding complete as specified and directed.

S & F mild steel bars conforming to Fe 290 Gde E-165 as in guard bars or similar works including welding etc complete all as specified.

S & F Sheet glass ordinary quality and glazing with oil putty in square n exe 0.5 sq m in each pane (Thickness in 3.00mm) complete all as specified and directed.

S&F 3mm thick frosted glass panes and glazing with oil putty & pins/spring pins complete in squares n.exc 0.50 sqm each panes complete all as specified and directed.

S & F aluminium anodised ventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass including necessary channel frame work, including rubber gasket and frame with wire mesh of aluminium,and deco grill ,aluminium beading complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamal paint over a coat of red oxide primer complete all as specified.

Preparation of new or previously untreated wooden surfaces of any description, not otherwise, described, over 10cm width or girth and applying two coats of synthetic enamal paint over a coat of pink primer complete all as specified.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for non skid ceramic (colored) tile, 7 to 8 mm thick as in floor area of each tile exceeding 0.11 Sqm but n exceeding 0 .18 Sqm , set and jointed in neat cement slurry and pointed in white or colored cement to match incl and over screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed.

M&L for Glazed ceramic coloured tiles of size 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match 15mm thick backing coat CM 1:4 complete all as specified and directed.

Dismantling asbestos cement (corrugated or semi corrugated, etc)sheets in roof covering complete all as specified.

S & F prepainted galvalume aluminium zinc coating GI base corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.(Note : Corrugation colour and shape of sheet shall be approved by GE)

S & F prepainted galvalume aluminium zinc coating GI base plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge, fixed with self tapping screws including neoprene and EPDM washers complete all as specified and directed.

Dismantling wall and ceiling boards any thickness including cover fillets complete all as specified and directed.

M&L for 6mm thick AC plain building boards fixed as in ceiling complete all as specified and directed.

S&F mild steel rolled sections as in framing for fixing boards in ceiling and the like fixed with angle cleats and connecting plates of grade Fe-410-S complete all as specified and directed.

Demolition of cement concrete unreinforced of Concrete of any description and in any position not otherwise specifically provided for where directed.

Removing of existing un-serviceable water proofing treatment , taking down cement plaster etc, of any description and claening of top surfaces of cement concrete flushing out junction of parapet walls and washing down with water complete all as specified and directed.

M&L for water proofing treatment to non accessible RCC roofs by providing 10mm thick screed in CM 1:3 mixed with & including water proofing compound @ 3% by weight of cement & applying one coat of bituminous primer @ 0.30 kg/sqm & laying APP based polymer modified membrane with polyster non woven reinforced of weight not less than 3 kg/sqm 3mm thick with polythene finished sealing with side over laps of 75mm & 100mm laps at the ends of membrane by torch application method & applying two coats of aluminium paint as per the makes approved by the Engr-in-Charge.

M&L PCC 1:2:4 type B0using 12.5mm graded stone aggregate as in, levelling coarse complete all as speificed and directed

Demolition of Brick work or stone/boulder masonry, build in cement mortar or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

Taking down cement or lime plaster of any description from stone or brick walls etc including raking out joints, hacking for key scrubbing down with water and disposing off the rubbish complete all as specified and directed.

M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in CM (1:4) finished even and fair without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on any faces of brick work in CM1:6, finished even and fair complete all as specified and directed..

M & L for 5mm thick rendering on cement concrete as in ceiling with cement mortar 1:3 complete all as specified and directed.

Supply only Integral waterproofing compound.

M&L for preparation of new surfaces of ceiling plastered/AC sheet and applying three coat of white wash complete all as specified

M&L for preparation of old plastered and un-plasterd surfaces on ceiling applying one coat of white wash complete all as specified

M&L for preparation of new plastered surfaces on walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for prepartion of new plastered surfaces on walls and applying two coats of cement based paint over one coat of primer on walls complete all as specified and directed by the Engr-in-Charge

M&L Preparation of old or previously treated steel surfaces of any description not other wise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed by EIC.

M&L for complete removal of existing treatment and applying two coats of cement based paint over one coat of Primer on walls all as specified and directed by the Engr-in-Charge

M&L complete removal of existing treatement and applying two coats of oil bound distemper over a coat of primer, an old plastered or un-plastered surfaces on walls complete all as specified and directed by Engr-in-Charge

M & L applying 2 mm thick wall care putty on wall for smoothing of surface complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials where directed complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-1 using 20mm graded stone aggregate 75mm thick as in plinth protection including necessary form work and finishing surface even and smooth w/o using extra cement including bitumen joints complete all as specified and directed.

M&L for 25mm thick Cement concrete type B-0), 1:2:4 (12.5mm graded aggregate) including necessary form work as in flooring, surface finished rough complete all as specified.

Taking up or down 15 mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

All as per item no 55 above but 20mm dia.

S&F 15mm bore tubes, `medium grade', galvanised, with all fittings and fixed complete concealed in walls and ceilings or laid in floors complete all as specified and directed.

S&F 20mm bore tubes, `medium grade', galvanised, with all fittings and fixed complete concealed in walls and ceilings or laid in floors complete all as specified and directed.

Demolition of old RCC water tank exc 500ltr capacity but n. exc 1000ltr capacity and removing rubbish off the premises from site out side of MD land complete all as specified and directed.

S&F 1000 ltr Rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I 1000 litres capacity complete all as specified and directed.

S&F Ball brass valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, 20mm bore, fixed in repair complete all as specified and directed.

S&F in repair Stop valves cast copper alloy Chromium plated fancy type long sank concealed type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed (15mm bore dia of pipe).

S&F in repair Bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed (15mm bore dia of pipe).

S&F pillar taps cast copper alloy with capstain heads chromium plated screwed down high pressure with or without lettered Hot and cold with lond screwed shanks and fly nuts screwed for iron pipe and fixed (15mm bore of pipe).

S&F 10 litre capacity PVC flushing cistern, valve less symphonic type low level or high level with inlet, ball valve float chains pull and brackets complete with flush pipe 32mm dia complete all as specified and directed.

S&F PVC connection 600mm long of dia 15mm complete all as specified and directed.

S &F vitreous china wash basins flat backsize 630 x 450mm including cutting for and pinning in ends of brackets or errecting stand white 32mm dia polyethylene fush pipe, PVC connections 15mm size with PTMT nuts of length 600 mm, 32mm dia PVC waste pipe for wash basins with inlet and outlet screwd for pipe or connections including necessary packing, union and cap and fixed etc including brackets compete all as specified.Fixed in repair

S & F Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union. Fixed in repairs

S&F in repair tubular towel rail 20mm dia D type and 60cm long including brackets fancy type brass chromium plated complete all as specified and directed.

S&F grating PTMT square of size 150mm complete all as specified and directed.

S & F Viterous China urinals, bowl type (back or corner wall type), of size 465 x 355 x 265mm white complete including providing and fixing plugs, bedding urinal agianst wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe. Fixed in repair

S &F vitreous china water closet Squatting Orissa patern white size 580 x 440mm with integral foot rest with P or S trap including , flushing cistern low or high level, 32mm dia polyethylene flush pipe etc compete all as specified.(excluding cost of flush tank) including provn of lime concrete bedding fixed in repairs

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc.,including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories)

M&L SGSW Gully trap squre or round mounted type 'P' 150mm x100mm complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketd, in any length with rubber ring joints laid in floor or fixed on wall all asspecifed and directed.

S&F 75 mm bore PVC (SWR) pipessoil waste and rain water drainage pipe (6 kgf/sqcm) single socketd, in any length with rubber ring joints laid in floor or fixed on wall all asspecifed and directed.

S&F PVC (SWR) 75 mm dia bend any radius with oval access door

S&F PVC (SWR) 110mm 75 mm dia reducers complete all as specified and directed.

S&F PVC (SWR) vent cowl size 110 mm dia complete all as specified and directed.

S&F PVC (SWR) 110 mm dia bends any radius with oval access door complete all as specified and directed.

S&F in repairs 20 mm dia stainless steel curtain rod incl brackets complete all as specified and directed.

M&L for grinding kota stone floor/skirting with suitable grit size Carborandum stones, and polishing including removal of black spots or any other faded spots on existing kota stone terrazzo surfaces complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F aluminium powder coated framed windows, any pattern, fixed/side hung/sliding Three track using powder coated aluminium sections or approved make, with or without sash bars, suitable for 5 mm thick glazing and stainless steel alloy wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm wire guaze, including necessary rubber packing, joining cleats, glazing clips, aluminium snap beading, handles, locking arrangements, frame of window should be of 1.5 mm thick section & shutter sec like handle/interlocking /top/bottom should be of 1.2 mm thick etc , complete all as specified and as directed Note :Rates include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle etc complete all as specified and directed.

M&L for grill medium grade of mesh size 75mmx75mm with 6mm square anodised aluminium bars fixed with suitable aluminum frame of size 37x19x2mm and all as secified.

M&L for Light shade Vitrified Ceramic tiles 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick Screed bed in CM 1:6 complete all as specified and directed.

All as per item No 87 above but on Vertical Surfaces with incl 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.18 Sqm but n. exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick screed bed CM 1:6 complete all as specified and directed..

All as per item No 89 above but in verticle surfaces with 10mm thick backing coat in CM 1:4 complete all as specified and directed.

S&F 4mm thick coloured textured designer ceiling board (Everest) of size 595X595 mm fixing with screws/clips including Tee grid suspension system of size 600 mm x600 mm type-1 made out of roll framed hot dipped galvanised steel zinc coated of not less than 120 gm/sqm ,main runner shall be 0.3 mm thick of section 24 mmX33 mm cross runner 0.3 mm thickof section 24 mmx25 mm,wall angle shall be 0.63 mm thick of section 24 mmx24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod ,system exposed portion shall be pre painted polyster coated in off white/white in colour complete with material,fixing, jointing etc complete all as specified and directed.

Dismantling of PVC water tanks or any description and at any position and removing to store / removing from site etc 500 ltrs and n.exc 1000 ltrs capacity.

Supply & fix 15mm dia brass CP mixer for WHB mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed

S&F in repairs Bath room cabinet (with locking plastic shelves ) 350 x 450 mm (Mirror cab) complete all as specified and directed.

S &F Wash down water closet (Pdestal pattern) white with P or S trap including plastic water closet seat & cover mild steel chromium plated or aluminised hinging device , flushing cistern low or high level, 32mm dia polyethylene flush pipe etc complete all as specified.(excluding cost of flush tank) Fixed in repairs

S&F Soap dish, vitreous China white, approximate size 160x 160x90 mm complete all as specified and directed.

S&F brass toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S & F Chromium plated shower roses with or without swivel joints, any size, including fix in to steel pipe or union complete all as specified and directed.

M&L for Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

M&L for Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40 gms) complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, plane with grating including jointing with solvent cement (Diameter of outlet 75mm).

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

Point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable 1.5 sqmm (Phase - Red/Yellow/Blue, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators complete for the following :-

One light point controlled by one switch.

One fan point controlled by one switch.

One socket outlet 6 amp controlled by one switch on the same board with other switches.

One socket outlet 6 amp controlled by one switch on indepdendent board.

One bell point controlled by one bell push.

Point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for one 16 amp socket outlet controlled by one switch on independent board complete.

S&F switch piano flush button single pole one way 6 amp complete.

S&F switch piano flush button single pole one way 16 amp complete.

S&F socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete.

S&F socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete.

S&F hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity including connecting up complete.

S&F ceiling rose 6 amp, 3 plates polycarbonate body complete.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLSH multistranded copper conductor cable (Phase - Red, Neutral - Black, Earth - Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories of following nominal sizes:-

2x4 sqmm + 1x4 sqmm earth continuity conductor in 20 mm dia conduit.

2x6 sqmm + 1x6 sqmm earth continuity conductor in 20 mm dia conduit..

S&F LED batten (1.2 m) made of Aluminium housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 100+ lumens per watt and total power consumption not less than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 complete. Make : Philips cat ref no. ENDURALED BATTEN " BN 108C LED 20S PSU CDL WH " or Havells Lumiline plus GE lighting as approved.

S&F LED fixture 8 watt including connection all as per Philips LED LINEA cat ref no. BN 550 WLED 6 - 6500 or eqivalent in Wipro or Havells as approved.

S&F LED bulkhead fitting 9 watt IP 66 & IK 09 with pressure diecast aluminum housing & polycarbonate diffuser duly prewired for connection with flexible multi stranded copper conductor cable as required all as per Philips cat ref no. WT202W LED6S CW PSU S1 PC or equivalent in Wipro or Bajaj or Havells as approved.

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

S&F MCB distribution board SPN, 240 volts, 8 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

S&F MCB distribution board ETPN, 415 volts, 4 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

S&F MCBs as per load requirement 'C' series of breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of following ratings:-

Single pole 6 to 16 amp. Make - Legrand DX3 cat ref no. 408587 to 408592 or equivalent in Schneider or Hager as approved.

Double pole 32 amp. Make - Legrand DX3 cat ref no. 408636 or equivalent in Schneider or Hager as approved.

Four pole 63 amp. Make-Legrand cat ref no. 408702 or equivalent in Schneider or Hager as approved.

Taking down carefully aluminium or copper submain wiring with PVC surface conduit or casing caping and making good disturbed surfaces complete.

Taking down MCB distribution boards with incoming and outgoing controls any make, any capacity after disconnecting complete.

Supply & fix exhaust fans AC single Phase 230/240 V of size 150/250 mm sweep with louver complete all as specified and directed.

Taking down carefully electric meters, any type upto 40 amps capacity after disconnecting and depositing in MES store yard complete.

S&F galvanized unwelded pressed steel terminal boxes concealed in wall of thickness 1.2 mm covered with phenolic laminated white sheet cover 3 mm thick in renewal of wooden meter boards of size 250mm x 300mm x 60mm deep for fixing energy meters complete

S&F fully transparent meter box suitable for energy meter made of polycarbonate/ high grade engineering plastic to permit clear view of display and can be sealed in such way that the entire meter is accessible only after breaking the seal complete.

Taking down Ceiling Fan of any make, type and sweep by disconnecting Electric Connection and keeping in safe castody for repair.

Dismantling of ceiling fan from existing location any sweep of any make, cleaning throughly, servicing of fan motor & parts fitted there in, oiling, greasing to bush / bearings, replacement of unserviceable parts required, applying two coat of white synthetic enamel paint over one coat of primer on fan blades and body, re- assembling, testing and hanging at site as directed.

S&F LED 20W streetlight made up of pressure die cast housing with prismatic polycarbonate diffuser and individual LED's with secondary optics and IP65 protection complete with fixing arrangement and connections as directed as per Bajaj cat Ref no. BCLST 20 W LED I code 169829 or equivalent in Philips or Wipro as approved.

S&F modular switch one way 6 amp 1 module all as per Legrand Mylinc cat ref no. 675501 or equivalent in Schneider Zencelo or MK Blenze as approved.

S&F modular switch one way 16 amp 1 module all as per Legrand Mylinc cat ref no. 675511 or equivalent in Schneider Zencelo or MK Blenze as approved.

S&F modular bell push, 6 amp, 1 module all as per Legrand Mylinc cat ref no. 675504 or equivalent in Schneider Zencelo or MK Blenze as approved.

S&F modular socket 6/16 - 2/3 pin combined 2 module all as per Legrand Mylinc cat ref no. 675555 or equivalent in Schneider Zencelo or MK Blenze as approved.

S&F modular socket 6 amp 2/3 pin combined 2 module all as per Legrand Mylinc cat ref no. 675552 or equivalent in Schneider Zencelo or MK Blenze as approved.

S&F bell multi music type, AC, 240 volts complete. Make- Anchor or SSK or Havells Reo as approved.

S&F modular hum free electronic step fan regulator, 100 watt 2 module all as per Legrand cat ref no. 675530 or equivalent in Schneider Zencelo or MK Blenze as approved.

M&L for LED Wall Washer rounded corners and white color, throw of the light in both the directions IP 44, aluminium body with 7 watt White led lamp and base including connection and fixing on wall as directed. Make Phili[ps, Model No: 34153 or equivalent in Havells or Wipro as approved.

S&F Power unit for AC or geyser 3.5 KW 4 module including sunken modular GI metal boxes not less than 1.2 mm thick and white modular mounting plates with frame all as per Legrand Mylinc cat ref no. 675558, 689009, 675564 & 675584 or eqivalent in Schneider Zencelo or MK Blenze as approved.

Hanging only ceiling fan and connecting up including provision of cable ceiling rose or connector to fans as directed.

M/S PRASHANT BENIWAL

Vardaini Industries