WBPWD/PW(R)/SE/SHC/NIT NO 07 OF 2026-2027(Sl no-01)

Dismantling of Flexible Pavements Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 metres, stacking serviceable and unserviceable materials separately (Reference to MoRT&H's specification clause 202) By Mechanical Means Bituminous course

Sand Filling in Foundation Trenches with good local sand free from earth not exceeding 150 mm compacted thickness including inundating each layer by profuse water and porking and rammimg layer by layer. Quality of sand is to be approved by the Engineer-in-charge.(Reference to MORT&H's specification 304). with Medium Sand

1B Granular Sub-Base with Graded Material By Mix in Place Method Construction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401 1B(iii) Rate per cum for grading-III Material

1B Granular Sub-Base with Graded Material By Mix in Place Method Construction of granular sub-base by providing graded materials such as natural sand/crushed gravel/crushed stone/combination depending upon the required grading , spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator and compacting with vibratory roller to achieve at least 98% of the maximum dry density for the material determined as per IS:2720 (Part 8), complete as per clause 401 desired density, complete as per clause 401 1B(V) Rate per cum for grading-V Material

Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate conforming to the grading of table 400- 13 revised vide table 2 of IRC : 109 (2015) to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density .The thickness of a single compacted layer shall not be less than 75 mm.(Reference to MoRT&H's specification 406. Using Pakur Variety Stone Aggregates.

Bituminous Macadam Providing and laying bituminous macadam with 100-120 TPH hot mix plant using crushed aggregates of specified grading premixed with approved bituminous binder @ 3.3% (min) for Grading -1 and 3.4% (min) for Grading -2 by weight of total mix, transported to site, laid over a previously prepared base with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction (Reference to MORT&H's specification clause 504). 3(ii) for Grading II (19 mm nominal maximum aggregate size) Layer Thickness 50-75mm (Payment will be made on the basis of finished compacted volume)

Filling Pot-holes and Patch Repairs with open-Graded Premix surfacing, 20mm. (Contd…) Removal of all failed material in the pavement courses and if necessary below the pavement until the root causes of the failure is removed, the trimming of completed excavation to provide firm vertical faces; specified for the pavement layer; application of tack coat conforming to cl. 503 of MORT&H's specification ,on to the sides and base of excavation prior to placing hot bituminous material as per clause 510 and the compaction,trimming and finishing of the surfaces of all patches to form a smooth continuous surface, level with the surrounding road as per the requirement of clause 3004.2 of MORT&H's specification.

Prime Coat Providing and applying primer coat with cationic bitumen emulsion SS1 grade conforming to IS:8887 on prepared porous granular surface including clearing of road surface and spraying primer using mechanical means (Reference to MORT&H's specification clause 502). i) On WMM/WBM surface @ 0.85kg /sqm. Using Cationic SS-1

Tack Coat Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). i) On bituminous surface @ 0.25kg /sqm Using Cationic RS

Tack Coat Providing and applying tack coat with Cationic bitumen emulsion (RS1) complying with IS:8887 using emulsion pressure distributor on the prepared bituminous/granular /cement concrete pavement surface cleaned with mechanical broom and high pressure air jet (Reference to MORT&H's specification clause 503). ii) On Granular surface treated with primer @ 0.275 /sqm. Using Cationic RS On bituminous surface