JJM Rearrangement and Upgradation of Bacteriology lab in QCDL PaJJM Modernization of QCDL Palakkad for obtaining NABL Accreditation for Bacteriological Lab General Civil Work

Amount

QCDL Palakkad

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

OD180552/2024-2025:Providing and fixing stainless steel platform for table /stand /slab and cupboard with rectangular /L-Type sections, made of 1.60 mm thick stainless steel ,joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with carbon steel galvanised dash fastener of required dia and size ( to be paid for separately)

15.3:Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.12.1:Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

15.57:Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge

5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

11.41.2:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

8.2.2.1:Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shadeArea of slab upto 0.50 sqm

8.3.2:Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

50.6.2.2:Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.46.1:Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

11.36:Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

10.5.2:Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6 mm for diagonal braces and central cross piece

21.13:Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete

9.63.3:Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete:150x10 mm

OD95503/2024-2025:Supply and fixing SS cabinet handles

OD95504/2024-2025:Supply and fixing slip in auto close hinges

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.2:Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.2:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

9.70.2:Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:100x58x1.90 mm

21.16.3:Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-Charge.Polyester powder coated minimum thickness 50 micron aluminium

OD133975/2024-2025:Supply installation of 1.5 TON Inverter Split AC of a reputed manufacturer including cost of AC & incidental charges of all fitting, installation cost etc.

OD133993/2024-2025:Shifting of AC and providing extra fittings and accessories such as stabilizer, Copper earthing, etc. The cost includes that of installation charges and required wiring arrangements etc complete as per the direction of engineer in charge

13.52.1:Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

17.11.2:Providing and fixing white vitreous china laboratory sink with C.I brackets, C.P. brass chain with rubber plug 40 mm C.P brass waste and 40 mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required:Size 600x450x200 mm

18.50.1:Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

17.7.11:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:Stainless Steel AISI - 304 (18/8) Wash basin 530 x 345 mm with single 15mm C.P. brass pillar tap

OD95507/2024-2025: Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and watering pipe of 2.7metre long etc.(but without charcoal/ coke and salt) as required.

OD95508/2024-2025:Supply and fixing following size/modules,PVC box along with modular base and cover plate for modular switches in recess etc.as required.Modular PVC box with cover plate for 8 module Data derived from DSR E&M 2016 1.27

OD95509/2024-2025:Supply and fixing following size/modules,PVC box along with modular base and cover plate for modular switches in recess etc.as required.Modular PVC box with cover plate for 12 module Data derived from DSR E&M 2016 1.27

OD95510/2024-2025: Supplying and fixing following rating, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63A 2 pole Isolator

OD95511/2024-2025:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required.63 Amp TP&N.

OD95512/2024-2025:Supplying and fixing following modular switch/ socket on the existing modular plate& switch box including connections but excluding modular plate etc. as required.3 pin 15/16 A socket outlet

OD95513/2024-2025:Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 32 A, one way modular switch

OD95514/2024-2025:Supply and fixing following size/modules,PVC box along with modular base and cover plate for modular switches in recess etc.as required.Modular PVC box with cover plate for 6 module Data derived from DSR E&M 2016 1.27

OD95515/2024-2025:Supply and fixing following size/modules,PVC box along with modular base and cover plate for modular switches in recess etc.as required.Modular PVC box with cover plate for 4 module Data derived from DSR E&M 2016 1.27

OD95516/2024-2025: Supplying and wiring with 6.00 sq mm PVC insulated standard single core copper wires in the existing surface/recess conduits as required including giving necessary connections.

OD95517/2024-2025:Supplying and wiring with 1.00 /1.5 sq mm PVC insulated standard single core copper wires in the existing surface/recess conduits as required including giving necessary connections.

OD95518/2024-2025:Supplying and wiring with 4.00 sq mm PVC insulated standard 4 core copper cable in the existing surface/recess conduits as required including giving necessary connections.

OD95519/2024-2025:Supplying and wiring with 2.5.00 sq mm PVC insulated standard single core copper wires in the existing surface/recess conduits as required including giving necessary connections.

OD95520/2024-2025: Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

OD95521/2024-2025:Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps RCCB 2 pole 30 ma

OD95522/2024-2025:Supplying and fixing of following ways surface/ recess mounting vertical type, 415V, TPN MCB distribution board of sheet steel, dust protected duly powder painted, inclusive of 200A, tinned copper bus bar, common neutral link, earth bar , din bar for mounting MCBs (but without MCBs and incomer) as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

OD95523/2024-2025: Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps RCCB 4 pole 30 ma.

OD95524/2024-2025: Supply and drawing bare earthing conductors of the following sizes along with wiring /cables and giving connection as required.3.15 mm copper conductor (10 SWG)

OD95525/2024-2025: Supply of superior quality copper earth socket for the following sizes of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

OD95526/2024-2025: Supplying and fixing of Earth bench Terminal strip

OD95527/2024-2025: Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connection etc. as required.

OD95528/2024-2025: Supplying and fixing LED tube(20W). including wire , holder.

OD95529/2024-2025: Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

OD95530/2024-2025: Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

OD95531/2024-2025: Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

OD95532/2024-2025: Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm.

OD95533/2024-2025: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A, one way modular switch

OD95534/2024-2025: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet

OD95535/2024-2025: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A, one way modular switch

OD95536/2024-2025: Supplying and fixing 20 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top along with 20 A "C" curve, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

OD95538/2024-2025:300/305 mm sweep Light Duty Exhaust fan in metal frame working on 230 V A/C -

OD95539/2024-2025: Suppply and fixing 1 no metal box with 1 no white front plate on 1 nos 20/25A modular type DP switch with indicator and 25A shuttered socket,earthing make good the damages color washing etc. as required on recess the power plug(ROHS)

OD95540/2024-2025:Submission of Application for getting power/load enhancement from KSEB as per the direction of Departmental officers including the cost of Application form to be remitted to KSEB (excluding the Statutory fees to be paid to KSEB which will paid by KWA directly to KSEB on getting the demand note)

OD95541/2024-2025:Engaging Coolie for various activites for work

OD170464/2024-2025:Supplying and fixing charges for all plumbing works

UNNIKANNAN V (BID ID -2092737)

Bidder Name

UNNIKANNAN V

UNNI L J