Providing and Fixing fabrication shed with plinth and alteration of existing GI Sheet with Toilet Block at Bardoli Divisional Store under Bardoli Division.

Name of work :- Providing and Fixing fabrication shed with plinth and alteration of existing

GI Sheet with Toilet Block at Bardoli Divisional Store under Bardoli Division

m Description Qty. Unit Rate Amount

Boring holes 3.5 m deep in ordinary soil (for cast in situ

piles) and getting out the soil and disposal of the surplus

excavated soil as directed within a lead of 50 Meter for

following diameter of pipes.(iii) 300 mm

Excavation for foundation upto 1.5 m depth including

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(B)

Dense or Hard soil

Excavation for foundation for depth from 1.5 m to 3.0 m

including sorting out and stacking of useful materials

and disposing off the excavated stuff upto

Meter lead.(B) Dense or Hard soil

Filling available excavated earth (excluding rock) in

trenches. plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each

disposited layer by ramming and watering.

Providing, laying, spreading and compacting graded stone

aggregate to wet mix macadam specification including

premixing the Material with water at OMC in mechanical mix

5 plant carriage of mixed Material by tipper to site, laying in 115.00 CMT 1327.00

uniform layers with paver in sub- base / base course on well

prepared surface and compacting with vibratory roller to

achieve the desired density.

Filling in plinth with sand under floors including

6 watering ramming, consolidating and dressing 40.00 CMT 477.03

complete (more than 10 ton)

Filling in foundation and plinth with murrum or selected soil

7 in layers of 20cm. thickness including watering, ramming 290.00 CMT 298.79

and consolidating etc. complete. (upto 10 ton)

Providing and laying cement concrete 1:3:6 (1- Cement : 3-

Coarse sand : 6- Graded brick bat aggregate 40mm normal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth (upto 10 ton)

Providing and laying controlled cement concrete M.200 and

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (A)

Foundations, footings, Base of columns and Mass concrete

Finishing concrete surface with machine Power Trowel and

making line for anti skid.

Expansion joint Cutting and filling with asphalt in concrete

11 by machine saw upto 80 mm height and upto 10 mm thick. 285.00 RMT 35.00

m Description Qty. Unit Rate Amount

Providing and laying controlled cement concrete M-200

exposed work with curing and finishing smooth etc.

complete including the cost of formwork but excluding the

cost of reinforcement for R.C.C work in (B) COLUMNS: (ii)

Having cross-sectional area more than 0.18 Sq.M

Providing and laying controlled cement concrete M.200

exposed work with curing etc. complete including the cost of

13 formwork but excluding the cost of reinforcement fo R.C.C. 29.00 CMT 7589.70

work in (A) BEAMS :(iii) Having cross-sectional area

more than 0.08 Sq.M and upto 0.12 Sq.M

Providing TMT Bar FE 500/500D reinforcement for R.C.C.

14 work including bending, binding and placing in position 6250.00 KG 76.52

complete upto floor two level

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. In foundation

and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)

(C) Fly Ash Bricks

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

plastering upto floor two level and finished even and smooth

in (i) Cement mortar 1:3 (1-cement:3-sand)

Providing and fixing of Ridge flashing for roof panel shall be

made out of 0.5 mm thick pre coated GI sheet . The

Precoated sheet shall be of minimum 240 mpa steel grade

confirming to IS 14246:1995 and shall have zinc coating of

minimum 120 gsm as per IS:277:1992 , 5-7 microns epoxy

primer on both side of the sheet and polyester top coat 15-

18 micron. The PPGI Sheet shall have plastic protective

17 guard film of minimum 25 microns to avoid scratches 1270.00 SMT 858.80

during transportation. The ridge shall be fixed to the steel

members by pop rivet or self drilling/self stitching fastners

@ maximum 450 mm c/c along length of capping/flashing

etc complete . (Note - for payment the measurement of

area shall be that of actual net area of sheet fixed.)

Providing and fixing of Ridge flashing for roof panel shall be

made out of 0.5 mm thick pre coated GI sheet. The

Precoated sheet shall be of minimum 240 mpa steel grade

confirming to IS 14246:1995 and shall have zinc coating of

minimum 120 gsm as per IS:277:1992 , 5-7 microns epoxy

primer on both side of the sheet and polyester top coat 15-

18 18 micron. The PPGI Sheet shall have plastic protective 121.00 RMT 515.28

guard film of minimum 25 microns to avoid scratches during

transportation. The ridge shall be fixed to the steel

members by pop rivet or self drilling/self stitching fastners

@ maximum 450 mm c/c along length of capping/flashing

Steel work, welded in built up sections framed work

including cutting, hoisting, fixing in position and applying a

priming coat of red lead paint. (A)In beams and joists,

channels angles Tees, flats, with connecting plates or angle

cleats as in main and cross beams. Hip and jack rafters,

purlins conneted to common rafters and the like

m Description Qty. Unit Rate Amount

Providing laying and jointing in true line and level 50mm

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings

make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent

20 as approved by Engineer In Charge. Pipe shall be fixed on 15.00 RMT 193.73

the wall with the help of clamp at every two metre C/C or

shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings

make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent

21 as approved by Engineer In Charge. Pipe shall be fixed on 25.00 RMT 146.65

the wall with the help of clamp at every two metre C/C or

shall be concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

22 be fixed on the wall with the help of clamp at every two 20.00 RMT 90.93

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost of

Providing laying and jointing in true line and level 15mm

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

23 be fixed on the wall with the help of clamp at every two 25.00 RMT 71.93

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost of

Providing and fixing Gun metal check or non-return fullway

wheel valve.(C) 25mm dia.

Providing and fixing Gun metal check or non-return fullway

wheel valve.(E) 40mm dia.

Providing and fixing Two way BIB cock with wall flange of

genuine Jaquar ompany brand, in with model no FUS-

26 CHR29041, water tap brand or approved ISI brand quality, 6.00 NO 2300.00

fixing in pieline and testing the same… etc., complete., as

directed by EIC

Providing and fixing brass screw down stop tap.(A)

Providing and fixing chromium plated brass half trun

28 flush cock of approved quality including fixing in pipe 2.00 NO 261.16

line etc. complete.(ii) 25mm dia.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

29 Dia. Low densidy, complete with special falnge compression 10.00 RMT 190.12

type fittings, wall clipsetc. including making good the wall

ceiling and floor. (E) 50mm

m Description Qty. Unit Rate Amount

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure polythene pipes of the following outside

30 Dia. Low densidy, complete with special falnge compression 15.00 RMT 277.46

type fittings, wall clipsetc. including making good the wall

ceiling and floor. (F) 75mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

31 Dia. Low densidy, complete with special falnge compression 25.00 RMT 335.69

type fittings, wall clipsetc. including making good the wall

ceiling and floor. (G)110 mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

32 Dia. Low densidy, complete with special falnge compression 15.00 RMT 510.17

type fittings, wall clipsetc. including making good the wall

ceiling and floor.160 mm

Providing and fixing PVC SWR Nahni trap IS 14735 for drain

- 75 mm diameter with jali of the following nominal

33 diameter of self cleansing design with C.I scread down or 2.00 NO 580.47

hinged grating including the cost of cutting and making

good the walls.

Constructing brick masonry chamber for underground C.I.

Inspection chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions

total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top

34 slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded 2.00 NO 2903.89

stone aggregate 20mm size) foundation concrete 1:5:10

inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and

bed concrete etc. complete.(i) Inside dimensions 455mmx

610mm and 450mm deep for pipe lines with three or more

Providing and fixing C.I. Manhole cover with frame 0.60 M.

x 0.45M. size having weight not less than 35Kg.

Providing and fixing S.W. gully trap with C.I. grating brick

masonry chamber and water tight C.I. cover with frame of

300mm x 300mm size (inside) with standard weight.(i)

Square mouth traps.(B) 150mm x 100mm size P or R type

Providing and fixing washbasin with single hole for pillar tap

with C.I. or M.S. brackets painted white including sutting

37 holes and making good the same but excluding fittings.(A) 2.00 NO 3265.89

Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm

size. (i) In white colour.

Angle Cock with PVC pipe connection upto WHB

Providing & fixing pillar taps of approved quality(Jaquar cat

no 5309) with capstan head screw down high screws,

shanks & back nuts. (ii) 15mm dia.

Hose pipe for pillar cock

m Description Qty. Unit Rate Amount

Providing, fixing,testing & commissioning of White

Vitereous China Floor mounting / Wall Mounted type

European Water Closet / Orissapan with C.P. bolts, nuts,

C.I. chair (painted with two coat of enamel paint over

41 a coat of primer) or other hanging arrangement, built 2.00 NO 6941.30

in concealed low volume compatiable cistern with C.P.

bolts, nuts supporting arrangements, bakelite

/polypropylene seat & cover with C.P. hinges & rubber

buffers, complete with all accesories. Including cutting &

making good the walls & floor whereever required. W.C.

pan with ISI marked white solid plastic seat and lid

42 Jet spray heavy duty with S.S. Braided hose 100 cm long 2.00 NO 305.93

43 Concealed cock 15 mm Heavy duty with cap 2.00 NO 486.44

Concealed Flush Valve with all connecting pipes for WC

Providing and fixing white vitreous china flat back half

stall urinal of size 580x380x350 mm with white PVC

automatic flushing cistern, with fittings, standard size C.P.

brass flush pipe, spreaders with unions and clamps (all in

45 C.P. brass) with waste fitting as per IS : 2556, C.I. 2.00 NO 10128.00

trap with outlet grating and other couplings in

C.P. brass,including painting of fittings and cutting and

making good the walls and floors wherever required : Single

half stall urinal with 5 litre P.V.C. automatic

flushing cistern

Providing and fixing in position cowel went to pipes.(C)

Providing and fixing 600mm x 450mm bevelled edge mirrror

of superior glass mounted on 6mm thick A.C. sheet or

plywood sheet and fixing to wooden pluge with C.P. brass

screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P.

48 brass brackets fixed to wooden plugs with C.P. brass scews. 2.00 NO 610.32

(B) 600mm x 20mm size.

Providing and fixing Toilet paper holder (A) C.P brass

Providing and fixing PTMT soap dish holder having length of

138mm, breadth 102mm, height of 75mm with concealed

fitting arrangements.

Providing erecting and fixing double coated ISI water tank

51 of required capacity each with all necessary fittings and 2000.00 Lit 3.91

connection etc. complete on terrace

52 PVC 4kg 90 mm dia rain water pipe 120.00 RMT 125.00

Miscellaneous expense for unforseen work which shall be

53 paid as per SOR Rate. Rate for Non SOR item shall be paid 1.00 JOB 25000.00

at approved rate analysed by EE Civil & DE Civil.

Total Amount (Excluding GST)

Total Amount (Excluding GST)

m Description Qty. Unit Rate Amount

"All royalties, toll tax, local tax, development charges, and any other taxes etc., in respect of this contract and also

any statutory variation in future towards above mentioned taxes & any other taxes if levied in future by statutory

authority applicable to the this contract shall be payable by the con-tractor and DGVCL will not entertain any claim

whatsoever in this respect.

The Contractor has to pay 1% Labour Welfare Cess of estimated cost to the concern Government Department.

The contractor shall produce the receipt of payment of 1% welfare cess from the respective govt. department before

submission of final bill, otherwise final bill for the works will not be finalized.

The proof of payment made by the contractor to the appropriate department shall be submitted to DGVCL, failing

which appropriate amount shall be withheld on getting information/instruction from the concerned department.

I /We agree to carry out the above work at

Add (+)________% above . Rs.

Less (-) _________% below Rs.

Total cost of work. Rs.

(Total cost of work Rs. ______________________________

Signature of Tendered CEO & SE (O&M)

Seal of company DGVCL,Circle Office Surat-R