Loading
Loading…
Loading…
Tender ID
Tender Value
₹26.5 Cr
EMD Value
₹26.5 L
Closing Date
23 Mar 2026, 6:00 pmClosed
Executive Engineer, Mahisagar (R&B) Division, Lunawada
Construction of Adarsh Nivashi Shala (Mixed) at Malvan Ta. Kadana Dist. Mahisagar
285333
29 of 2025-26
Open
Civil Works - Buildings
Works
Mahisagar
4 documents required · 4 mandatory
₹18,000
Yes
Executive Engineer, Mahisagar (R & B) Division, Lunawada
₹26.5 L
Yes
11 Mar 2026
11 Mar 2026
11 Mar 2026
23 Mar 2026
11 Mar 2026
No. Figure Amount
1 Excavation for foundation upto 1.50 mt depth including sorting out and 3162.00 Cum 268.92
stacking of useful materials and disposing the excavated stuff within all lead
and lift for hard murrum.
2 Excavation for foundation upto 1.50 mt depth including sorting out and 7416.00 Cum 278.06
stacking of useful materials and disposing the excavated stuff within all lead
and lift for soft rock not requiring blasting.
3 Excavation for foundation from 1.50 mt to 3.00 mt. depth including sorting out 7024.00 Cum 301.85
and stacking of useful materials and disposing the excavated stuff within all
lead and lift for soft rock not requiring blasting.
4 Excavation for foundation from 1.50 mt to 3.00 mt. depth including sorting out 156.00 Cum 325.62
and stacking of useful materials and disposing the excavated stuff within all
lead and lift for Hard rock.
5 Filling in foundation and plinth with sand in layers of 20 cm thickness 981.90 Cum 479.80
including watering, ramming and consolidating etc. complete.
6 Filling available excavated earth (excluding rock) in trenches plinth side of 3636.70 Cum 136.92
foundation etc. in layer not exceeding 20 cm in depth consolidation each
deposited layer by ramming and watering etc. complete.
thickness including watering, ramming and consolidation etc. complete.
8 Carrying out plinth treatment to post construction / existing structure by 4482.00 Sq.m. 66.99
spraying chemical solution for termite control treatment including labour and
material consistent with ISI specifications. Using chlordene and Chiorpufiles
20 EC. As per 6131_paret-II concentration weight one percent is
recommended i.e. one litre 20 EC chemical emulsion with 19 litre give 1%
concentration inclusive of one litre chemical emulsion application at the rate
of 5 litre chemical / Sq.m. of surface is recommended as per I.S.
9 Providing and laying controlled cement concrete M-150 and curing complete 645.00 Cum 4022.72
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Foundations, footings, base of columns & mass
10 Providing and laying controlled cement concrete M-250 and curing complete 1752.00 Cum 4668.22
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Foundations, footings, base of columns & mass
11 Providing and laying controlled cement concrete M-250 and curing complete 134.00 Cum 7750.74
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Columns upto plinth level.
12 Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 1788.60 Cum 3092.22
crushed stone aggregate 40 mm nominal size) and curing complete including
cost of form work in foundation and plinth.
13 Providing and laying controlled cement concrete M-200 and curing complete 162.10 Cum 7717.41
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Columns for Ground floor.
14 Providing and laying controlled cement concrete M-200 and curing complete 159.00 Cum 7758.95
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Columns for First floor.
15 Providing and laying controlled cement concrete M-200 and curing complete 104.00 Cum 7800.49
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Columns for Second floor.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
16 Providing and laying controlled cement concrete M-200 and curing complete 43.00 Cum 7842.03
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Columns for Third floor.
17 Providing and laying controlled cement concrete M-200 and curing complete 13.00 Cum 7883.58
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Columns for Fourth floor.
18 Providing and laying controlled cement concrete M-250 and curing complete 413.00 Cum 6052.93
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in plinth beam.
19 Providing and laying controlled cement concrete M-150 and curing complete 588.70 Cum 4120.80
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Plinth Slab.
20 Providing and laying controlled cement concrete M-200 and curing complete 351.00 Cum 6365.02
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Beam for Ground floor.
21 Providing and laying controlled cement concrete M-200 and curing complete 343.00 Cum 6406.56
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Beam for First floor.
22 Providing and laying controlled cement concrete M-200 and curing complete 133.00 Cum 6448.10
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Beam for Second floor.
23 Providing and laying controlled cement concrete M-200 and curing complete 43.00 Cum 6489.64
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Beams for Third floor.
24 Providing and laying controlled cement concrete M-200 and curing complete 4.00 Cum 6531.19
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Beams for Fourth floor.
25 Providing and laying controlled cement concrete M-200 and curing complete 46.60 Cum 7820.43
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Lintels for Ground floor.
26 Providing and laying controlled cement concrete M-200 and curing complete 48.30 Cum 7861.97
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Lintels for First floor.
27 Providing and laying controlled cement concrete M-200 and curing complete 21.90 Cum 7903.51
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Lintels for Second floor.
28 Providing and laying controlled cement concrete M-200 and curing complete 8.10 Cum 7945.05
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Lintels for Third floor.
29 Providing and laying controlled cement concrete M-200 and curing complete 0.60 Cum 7986.60
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Lintels for Fourth floor.
30 Providing and laying controlled cement concrete M-200 and curing complete 24.90 Cum 8569.85
including the cost of form work and finishing exposed surface with cement
mortar 1:3 (1 cement : 3 sand) but excluding cost of reinforcement for
reinforced concrete work in Chhajjas for Ground floor.
31 Providing and laying controlled cement concrete M-200 and curing complete 28.10 Cum 8611.39
including the cost of form work and finishing exposed surface with cement
mortar 1:3 (1 cement : 3 sand) but excluding cost of reinforcement for
reinforced concrete work in Chhajjas for First floor.
32 Providing and laying controlled cement concrete M-200 and curing complete 10.40 Cum 8652.93
including the cost of form work and finishing exposed surface with cement
mortar 1:3 (1 cement : 3 sand) but excluding cost of reinforcement for
reinforced concrete work in Chhajjas for Second floor.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
33 Providing and laying controlled cement concrete M-200 and curing complete 6.10 Cum 8694.47
including the cost of form work and finishing exposed surface with cement
mortar 1:3 (1 cement : 3 sand) but excluding cost of reinforcement for
reinforced concrete work in Chhajjas for Third floor.
34 Providing and laying controlled cement concrete M-200 and curing complete 0.50 Cum 8736.02
including the cost of form work and finishing exposed surface with cement
mortar 1:3 (1 cement : 3 sand) but excluding cost of reinforcement for
reinforced concrete work in Chhajjas for Fourth floor.
35 Providing and laying controlled cement concrete M-200 and curing complete 640.30 Cum 6418.55
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Slabs for Ground floor.
36 Providing and laying controlled cement concrete M-200 and curing complete 542.00 Cum 6460.09
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Slabs for First floor.
37 Providing and laying controlled cement concrete M-200 and curing complete 231.00 Cum 6501.63
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Slabs for Second floor.
38 Providing and laying controlled cement concrete M-200 and curing complete 62.00 Cum 6543.17
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Slabs for Third floor.
39 Providing and laying controlled cement concrete M-200 and curing complete 5.20 Cum 6584.72
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Slabs for Fourth floor.
40 Providing and laying controlled cement concrete M-200 and curing complete 40.00 Cum 7551.77
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Staircases for Ground floor.
41 Providing and laying controlled cement concrete M-200 and curing complete 40.00 Cum 7593.31
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Staircases for First floor.
42 Providing and laying controlled cement concrete M-200 and curing complete 16.00 Cum 7634.85
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Staircases for Second floor.
43 Providing and laying controlled cement concrete M-200 and curing complete 6.00 Cum 7676.39
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in Staircases for Third floor.
44 Providing and laying controlled cement concrete M-200 and curing complete 153.80 Cum 6361.30
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in RCC Walls for Ground floor.
45 Providing and laying controlled cement concrete M-200 and curing complete 17.20 Cum 7959.94
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in RCC Walls for First floor.
46 Providing and laying controlled cement concrete M-200 and curing complete 31.20 Cum 8001.48
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in RCC Walls for Second floor.
47 Providing and laying controlled cement concrete M-200 and curing complete 29.20 Cum 8043.02
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in RCC Walls for Third floor.
48 Providing and laying controlled cement concrete M-200 and curing complete 23.00 Cum 8084.57
including the cost of form work but excluding cost of reinforcement for
reinforced concrete work in RCC Walls for Fourth floor.
49 Extra for additional height of propping and centering where the height of 155.00 Sq.m. 407.75
propping and centering exceeds 4.0 mt. between supporting floor to ceiling
including temporary brick or stone pillars for supporting as required.
50 Providing I.S.I. Mark T.M.T. bar Fe-500D for R.C.C. work including bending, 737742.00 Kg. 77.92
binding and placing in position complete upto all floor level.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
51 Providing and laying brick work using common burnt clay building 865.00 Cum 4214.33
conventional type bricks having crushing strength not less than 35 Kg./Sq.cm.
in foundation and plinth in cement mortar 1:6 (1 cement : 6 fine sand)
including the cost of all materials and labour charges etc. complete.
52 Providing and laying brick work using common burnt clay building 806.00 Cum 4496.05
conventional type bricks having crushing strength not less than 35 Kg/sq.cm.
in super structure above plinth level upto floor two level in cement mortar 1:6
(1 cement : 6 fine sand) for Ground Floor including the cost of all materials
and labour charges etc. complete.
53 Providing and laying brick work using common burnt clay building 647.00 Cum 4538.16
conventional type bricks having crushing strength not less than 35 Kg/sq.cm.
in super structure above plinth level upto floor two level in cement mortar 1:6
(1 cement : 6 fine sand) for First Floor including the cost of all materials and
labour charges etc. complete.
54 Providing and laying brick work using common burnt clay building 409.00 Cum 4580.28
conventional type bricks having crushing strength not less than 35 Kg/sq.cm.
in super structure above plinth level upto floor two level in cement mortar 1:6
(1 cement : 6 fine sand) for Second Floor including the cost of all materials
and labour charges etc. complete.
55 Providing and laying brick work using common burnt clay building 126.00 Cum 4622.40
conventional type bricks having crushing strength not less than 35 Kg/sq.cm.
in super structure above plinth level upto floor two level in cement mortar 1:6
(1 cement : 6 fine sand) for Third Floor including the cost of all materials and
labour charges etc. complete.
56 Providing and laying brick work using common burnt clay building 14.00 Cum 4664.51
conventional type bricks having crushing strength not less than 35 Kg/sq.cm.
in super structure above plinth level upto floor two level in cement mortar 1:6
(1 cement : 6 fine sand) for Fourth Floor including the cost of all materials and
labour charges etc. complete.
57 Providing and laying half brick work using common burnt clay building 251.00 Sq.m. 629.84
conventional type bricks having crushing strength not less than 35 Kg/Sq.cm
in cement mortar 1:4 (1 cement : 4 coarse sand) in cement mortar in
foundation and plinth including the cost of all materials and labour charges
etc. complete.
58 Providing and laying half brick work using common burnt clay building 845.00 Sq.m. 684.26
conventional type bricks having crushing strength not less than 35 Kg/Sq.cm
in cement mortar 1:4 (1 cement : 4 coarse sand) in cement mortar in super
structure for Ground floor including the cost of all materials and labour
charges etc. complete.
59 Providing and laying half brick work using common burnt clay building 952.00 Sq.m. 690.57
conventional type bricks having crushing strength not less than 35 Kg/Sq.cm
in cement mortar 1:4 (1 cement : 4 coarse sand) in cement mortar in super
structure for First floor including the cost of all materials and labour charges
etc. complete.
60 Providing and laying half brick work using common burnt clay building 452.00 Sq.m. 696.87
conventional type bricks having crushing strength not less than 35 Kg/Sq.cm
in cement mortar 1:4 (1 cement : 4 coarse sand) in cement mortar in super
structure for Second floor including the cost of all materials and labour
charges etc. complete.
61 Providing and laying half brick work using common burnt clay building 156.00 Sq.m. 703.17
conventional type bricks having crushing strength not less than 35 Kg/Sq.cm
in cement mortar 1:4 (1 cement : 4 coarse sand) in cement mortar in super
structure for Third floor including the cost of all materials and labour charges
etc. complete.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
62 Providing and fixing M.S. fabricated Main Door using 38 x 100mm and 25 x 25 6.00 Sq.m. 3016.87
M.S. box section frame work as shown in the detailed design provided by the
Architect office and double shutter specially designed hollow door with
horizontal 25 x 25mm M.S. square pipe bands at equal distance throughout
the height of the frame as per the detailed design provided by the Architect
63 Providing and fixing door having side hung single shutter having factory 79.80 Sq.m. 3382.49
fabricated standard extruded alluminium colour anodized hollow section
(Section 63.50mm x 38mm x 2.50mm thick) for door frame, hollow portion of
door frame shall be filled with non teakwood wood, with factory made 35mm
thick flush door both side pre laminated with 6 lever Mortice lock (Godrej or
equivalent), Door closers (Heavy type of 765 number) Hardwar of Everite
Prabhat or equivalent, SS Aldrop, SS handle size 15cm long, tower bolt size
20 cm etc. as per detail colour & pattern approved by this office including
necessary anodized alluminium fixtures and fastenings for all floors.
64 Providing and fixing door having side hung double shutter having Granite 44.00 Sq.m. 5892.34
stone with flat edge polished for door frame with factory made 35mm thick
flush door solid core both side finished with 1 mm laminate with 6 lever
Mortice lock (Godrej or equivalent), Door closers (Heavy type of 765 number)
Hardwar of Everite Prabhat or equivalent, SS Aldrop, SS handle size 15cm
long, tower bolt size 20 cm etc. as per detail colour & pattern approved by this
office including necessary anodized alluminium fixtures and fastenings for all
65 Providing and fixing door having side hung single shutter having Granite stone 317.00 Sq.m. 6219.58
with flat edge polished for door frame with factory made 35mm thick flush
door solid core both side finished with 1 mm laminate with 6 lever Mortice lock
(Godrej or equivalent), Door closers (Heavy type of 765 number) Hardwar of
Everite Prabhat or equivalent, SS Aldrop, SS handle size 15cm long, tower
bolt size 20 cm etc. as per detail colour & pattern approved by this office
including necessary anodized alluminium fixtures and fastenings for all floors.
66 Providing and fixing FRP frame size 100 x 50 mm and 28 mm thick FRP 305.00 Sq.m. 2377.76
single shutter with depressed panel shutter having extra reinforcement on
sides and edges and in gel coat finish. The core of the shutter and frame is to
be filled up with injected fire extinguishing grade polyurethane foam done in
situ along with embedded wooden pieces for stiffening and also for taking
hinges and fixtures. The whole FRP frame and shutter is to be water proof,
weather proof, termite proof and resistance to mild acid / alkali rates are to be
including S.S. hinges with necessary screws and alluminium fixtures and
fastening.
67 Providing & fixing fix louvers 114mm wide G.I. Sheets having in thickness of 271.20 Sq.m. 2404.81
0.55 mm & weight not less than 490 Gm/meter roll formed to create 84mm
wide louver snap fixed on special shaped G.I. channel. Fix louvers & channels
shall finished with powder coating of 55 micron as per detail drawing and as
directed by Engineer in charge etc. complete.
68 Providing and fixing window having extruded aluminum colour anodized 248.00 Sq.m. 1583.95
section frame main outer size 95mm x 24mm x 1.17mm (@ wt. of
kg/mt), horizontal three track member size 92mm x 31.75mm x 1.30mm (@
wt. of 1.07 Kg/mt), vertical member of size 92mm x 31.75mm x 1.50mm (@
wt. of 1.06 Kg/mt) with sliding shutters of horizontal member size 40mm x
18mm x 1.29mm (@ wt. of 0.456 Kg/mt), vertical member of size 40mm x
18mm x 1.29mm (@ wt. of 0.456 Kg/mt) with 5 mm thick transparent bronze
colour tinted float glass with powder coated alluminium fittings and fixtures
and transparent silicon sealant glass fixing to frame as per details etc.
complete for all floors.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
69 Providing and fixing window having extruded aluminum colour anodized 222.60 Sq.m. 1713.70
section frame main outer size 63.50 x 38.10 x 1.95 mm, @ Wt 1.094 Kg /
Rmt, horizontal two track member size 61.85 mm x 31.75 mm x 1.20mm @
wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x 31.75mm x 1.30 mm
@ wt.of 0.659 Kg/mt with sliding shutters of horizontal member size 40mm x
18mm x 1.29mm @ wt.of 0.456 Kg/mt, vertical member of size 40mm x 18mm
x 1.29mm @ wt.of 0.456Kg/mt, @ Wt. 0.457 Kg/mt with 5 mm thick
transparent bronze colour tinted float glass with powder coated aluminum
fittings and fixtures and transparent silicon sealant glass fixing to frame as per
details etc. complete for window for all floors.
70 Providing and fixing colour anodised Alluminium Section SLIDING window 65.00 Sq.m. 4800.53
(Four Track) using Jindal E Series {30 mm} or equivalent section shutter top &
bottom - 20993, 0.839 Kg./ Rmt. shutter inter lock-20550, 0.994 Kg./Rmt.
shutter side (handle) - 20553, 0.731 Kg./Rmt. frame-bottom with gutter-
21198, 3.197Kg./Rmt. frame top & side - 21204, 1.694 Kg./Rmt. using three
shutter 5 mm thick transparent tinted float glass and one shutter with
Stainless steel wiremesh shutters, rubber gasket, air lock strip and finishing
joints with silicon sealant, with standard extruded colour anodized aluminum
coated fittings and fixture & fastening etc. complete. {Colour as directed by
Engineer in charge except black & Alluminum section shall be Jindal or
equivalent brand and glass of Modiguard, AIS or equivalent brand}
71 Providing and fixing colour anodised Alluminium Section SLIDING window 31.00 Sq.m. 4017.78
(Three Track) using Jindal E Series {30 mm} or equivalent section shutter top
& bottom - 20993, 0.839 Kg./ Rmt. shutter inter lock-20550, 0.994 Kg./Rmt.
shutter side (handle) - 20553, 0.731 Kg./Rmt. frame-bottom with gutter-
20928, 2.032 Kg./Rmt. frame top & side - 20837, 1.197 Kg./Rmt. using two
shutter 5 mm thick transparent tinted float glass and one shutter with
Stainless steel wiremesh shutters, rubber gasket, air lock strip and finishing
joints with silicon sealant, with standard extruded colour anodized aluminum
coated fittings and fixture & fastening etc. complete. {Colour as directed by
Engineer in charge except black & Alluminum section shall be Jindal or
equivalent brand and glass of Modiguard, AIS or equivalent brand}
72 Providing and fixing standard extruded of alluminium section of size 63mm x 351.00 Sq.m. 1175.56
38.10mm x 1.2 mm (@ wt. 0.643 kg/Rmt.) with colour anodized alluminium
frame for ventilation with 5mm thick frosted glass as details etc. complete for
ventilation for all floors.
73 Providing and fixing standard extruded of alluminium section of size 63.50 x 61.00 Sq.m. 1525.00
38.10 x 1.95 mm (@ Wt. 1.094 Kg / Rmt) with colour anodized alluminium
frame with 5 mm thick transparent bronze colour tinted float glass as details
etc. complete for fix window for all floors.
74 Providing and fixing Safety Grills of required pattern for windows / door using 23405.00 Kg. 114.13
16mm dia M.S. polished bars and rectangular CRC pipes of size 50mm x
30mm x 2mm at required spacing as per design and hold fast with coach bolts
including one coat of primer and two coats of matt finished oil painting etc.
75 Providing and laying machine polished, machine cut, free edges, Granite 366.00 Sq.m. 2661.35
stone slab 18 mm (average) thick {single piece not more than 150 cm} for
stair steps and riser as per design including full moulded round front edge in
tread of steps laid on 20 mm thick cement mortar 1:6 (1 cement : 6 coarse
sand) and skirting on 10mm thick cement plaster 1:3 (1 cement : 3 coarse
sand) and jointed with grey cement slurry including rubbing and polishing etc.
76 Providing and laying machine polished, machine cut, free edges, strip flooring 50.00 Sq.m. 2305.83
(75mm strips) for Ramp of Granite stone slab 18 mm thick laid on 20 mm
thick cement mortar 1:6 (1 cement : 6 coarse sand) and jointed with grey
cement slurry including rubbing and polishing etc. complete.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
77 Providing and laying 600 mm x 600 mm SOLUBLE SALT VITRIFIED TILES 879.00 Sq.m. 1401.38
10 mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 (1
cement : 6 coarse sand) on new surface and jointed with color cement slurry
including finished with flush pointing & cleaning the surface etc. complete for
light shade (APPROX. 10% DARK COLOUR TILES FOR PATTERN)
78 Providing and laying SOLUBLE SALT VITRIFIED TILES 10 mm thick, 600 96.00 Sq.m. 1195.02
mm x 600mm in skirting, risers of steps and dedo on 10mm thick cement
plaster 1:3 (1 cement : 3 coarse sand) and jointed with white cement slurry.
79 Providing and laying Granite tread & 600 x 600 x 10 mm thick SOLUBLE 87.00 Sq.m. 2298.76
SALT VITRIFIED TILES risers as per design including full moulded round
front edge in trade of steps laid with nosing and embossed anti-skid strips
with skirting on 10 mm thick cement mortar 1:3 (1 cement : 3 coarse sand)
jointed with grey cement slurry including rubbing and polishing etc. complete
80 Providing and laying 60cm x 60cm machine cut mirror polished blue kota 6595.00 Sq.m. 1189.72
stone slab flooring over 20mm (average) thick base of cement mortar 1:6 (1-
cement : 6 coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid
over and jointed with grey cement slurry mixed with pigment to match the
shade of slab including rubbing and polishing etc. complete. (A) 25mm thick.
81 Providing and laying 300 x 300 mm MATT FINISHED Ceramic tiles in flooring 45.00 Sq.m. 1005.52
treads of steps and landings laid over 20 mm. (average) thick base of cement
mortar 1:6 (1 cement : 6 coarse sand) and jointed with grey cement slurry with
flush pointing in white cement etc complete. Color & shade of which shall be
as approved by this office.
82 Providing and laying machine cut mirror polished blue kota stone slab 25mm 295.00 Sq.m. 1347.89
thick in risers of steps, skirting, dedo and pillars laid on 10mm thick cement
mortar 1:3 (1 cement : 3 coarse sand) and jointed with gray cement slurry
mixed with pigment to match the shade of slab including rubbing and
polishing etc. complete.
83 Providing and laying rough chiseled dressed stone flooring over 20mm thick 320.00 Sq.m. 576.79
base of cement mortar 1:5 (1-Cement : 5 coarse sand) or L.M. 1:1.5 (1 Lime
putty : 1.5 coarse sand) including pointing with cement mortar 1:2 (1 cement :
2 stone dust) etc. complete. (A) 25mm thick
84 Providing and laying 60cm x 60cm Anti skid Ceramic tiles 6mm thick of 376.00 Sq.m. 1005.52
approved brand in flooring treads of steps and landing laid on a bed of 12 mm
thick cement mortar 1:3 (1 cement : 3 coarse sand) finishing with flush
pointing in white cement. Pattern, Colour, Shade & pattern approved by
Architect or Engineer in charge.
85 Providing and laying 30cm x 30cm Anti skid Ceramic tiles 6mm thick of 703.00 Sq.m. 1005.52
approved brand in flooring treads of steps and landing laid on a bed of 12 mm
thick cement mortar 1:3 (1 cement : 3 coarse sand) finishing with flush
pointing in white cement. Pattern, Colour, Shade & pattern approved by
Architect or Engineer in charge.
86 Providing and laying glazed tiles of the size 30 cm x 45cm and 8 mm thick of 3413.00 Sq.m. 1488.24
approved brand in skirting, risers of steps and dedo on 10 mm. thick cement
plaster 1:3 (1 cement : 3 coarse sand) & pointing in white cement and jointed
with white cement slurry.
87 Providing and fixing precast Rubber Dye / steel dye inter locking concrete 3718.00 Sq.m. 706.77
block 60mm thick with grade of concrete M-300 pneumatic compressed /
vibrated mechanically and as per approved design confirming to IS 15658 :
2006 including 35 mm sand layer for levelling and filling the joint with sand in
proper line and level as per guidlines of IRC : SP 63-2018 etc. complete.
88 Providing and fixing precast concrete kerb stone of grey cement based 1964.00 Rmt. 388.99
concrete block 30 cm length, 30 cm height and 15 cm thick of M-250 grade
concrete as per approved design and including excavation for fixing in proper
line and level, filling the joints with C.M. 1:3 (1 cement : 3 fine sand) etc.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
89 Providing and laying water proofing treatment with china mosaic tiles flooring 3889.00 Sq.m. 1077.01
over avg 40 mm C.C. 1:2:4 {1 Cement : 2 sand : 4 Kapachi / Grit 6 to 12 mm
size} bedding for maintaining slope for plain and curve surface & 12 mm to
mm of broken piece of ceramic / glazed tiles (one for more color as directed)
to be laid over cement mortar bedding of C.M. 1:3 (1 cement : 3 sand)
containing one Kg of water proofing materials per bag of O.P.C. at plain or /
and slops and to be tempered to bring mortar ceramic up to surface with
using white cement and colour pigment including rounding of junctions and
extending them up to 15 cm along the wall and curing with bends any patterns
or design as per drawing and cleaning by using oxalic acid etc. complete.
90 Providing and fixing mirror polished machine polished Granite stone slab 1427.00 Sq.m. 4108.68
18mm (average) thick for Doors / Windows sill & jams cladding as per design
including half round moulded both edges fixed on 12mm thick cement plaster
1:3 (1 cement : 3 coarse sand) jointed with grey cement slurry including
rubbing and polishing etc. complete with necessary G.I. fastening for long
side in top. Colour and finish as directed.
91 Providing 20 mm thick double coat mala cement plaster on interior brick / 7367.00 Sq.m. 283.95
concrete work for plastering comprising of base coat of 12 mm thick cement
plaster in cement mortar 1:4 (1 cement : 4 coarse sand) in rough finishing and
8 mm thick top coat of cement mortar 1:2 (1 cement : 2 coarse sand) finished
with trowel including scaffolding, curing for Ground floor etc. complete.
92 Providing 20 mm thick double coat mala cement plaster on interior brick / 7551.00 Sq.m. 311.18
concrete work for plastering comprising of base coat of 12 mm thick cement
plaster in cement mortar 1:4 (1 cement : 4 coarse sand) in rough finishing and
8 mm thick top coat of cement mortar 1:2 (1 cement : 2 coarse sand) finished
with trowel including scaffolding, curing for First floor etc. complete.
93 Providing 20 mm thick double coat mala cement plaster on interior brick / 4055.00 Sq.m. 338.41
concrete work for plastering comprising of base coat of 12 mm thick cement
plaster in cement mortar 1:4 (1 cement : 4 coarse sand) in rough finishing and
8 mm thick top coat of cement mortar 1:2 (1 cement : 2 coarse sand) finished
with trowel including scaffolding, curing for Second floor etc. complete.
94 Providing 20 mm thick double coat mala cement plaster on interior brick / 1058.00 Sq.m. 365.64
concrete work for plastering comprising of base coat of 12 mm thick cement
plaster in cement mortar 1:4 (1 cement : 4 coarse sand) in rough finishing and
8 mm thick top coat of cement mortar 1:2 (1 cement : 2 coarse sand) finished
with trowel including scaffolding, curing for Third floor etc. complete.
95 Providing 20 mm thick double coat mala cement plaster on interior brick / 80.00 Sq.m. 392.87
concrete work for plastering comprising of base coat of 12 mm thick cement
plaster in cement mortar 1:4 (1 cement : 4 coarse sand) in rough finishing and
8 mm thick top coat of cement mortar 1:2 (1 cement : 2 coarse sand) finished
with trowel including scaffolding, curing for Fourth floor etc. complete.
96 Providing 20 mm thick double coat mala cement plaster on interior brick / 16.00 Sq.m. 420.10
concrete work for plastering comprising of base coat of 12 mm thick cement
plaster in cement mortar 1:4 (1 cement : 4 coarse sand) in rough finishing and
8 mm thick top coat of cement mortar 1:2 (1 cement : 2 coarse sand) finished
with trowel including scaffolding, curing for Fifth floor etc. complete.
97 Providing 10 mm thick cement plaster in single coat for plastering on Ceiling & 4175.00 Sq.m. 173.23
soffits of stairs upto floor two level and finished even and smooth in cement
mortar 1:3 (1 cement : 3 sand) etc. complete for Ground floor.
98 Providing 10 mm thick cement plaster in single coat for plastering on Ceiling & 3696.00 Sq.m. 195.11
soffits of stairs upto floor two level and finished even and smooth in cement
mortar 1:3 (1 cement : 3 sand) etc. complete for First floor.
99 Providing 10 mm thick cement plaster in single coat for plastering on Ceiling & 1573.00 Sq.m. 217.00
soffits of stairs upto floor two level and finished even and smooth in cement
mortar 1:3 (1 cement : 3 sand) etc. complete for Second floor.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
100 Providing 10 mm thick cement plaster in single coat for plastering on Ceiling & 554.00 Sq.m. 238.89
soffits of stairs upto floor two level and finished even and smooth in cement
mortar 1:3 (1 cement : 3 sand) etc. complete for Third floor.
101 Providing 10 mm thick cement plaster in single coat for plastering on Ceiling & 210.00 Sq.m. 260.77
soffits of stairs upto floor two level and finished even and smooth in cement
mortar 1:3 (1 cement : 3 sand) etc. complete for Fourth floor.
102 Providing & fixing Chicken mesh jali with square of 12.50 x 12.50mm of 25 1417.00 Sq.m. 92.92
gauge at junction the brick masonary and reinforcement cement concrete
member including fixing materials, scaffolding, labour etc. complete as
directed by the Engineer-in-charge.
103 Providing 12mm wide groove / notch in plaster including finishing the same 4740.00 Rmt. 15.15
etc. complete for all heights.
104 Applying water proofing treatment to sunk portion by applying acrylic polymer 716.00 Sq.m. 98.98
base water guard material applied with brush after cleaning of dirt, dust and
other foreign material.
105 Providing 20 mm thick waterproof cement plaster for sunk in single coat on 1136.00 Sq.m. 357.24
brick / concrete walls for interior plastering finished even and smooth in
cement mortar 1:3 (1 cement : 3 sand) and mixing water proofing materials of
approved brand and manufacture in C.M. in proportion recommended by the
manufacture and finished with a floating coat of neat cement slurry for all
106 Providing and filling screened of burnt coat cinder including and consolidation 150.00 Cum 621.46
etc. complete.
107 Applying two coats of acrylic lappy - putty & two coats of primer of approved 29785.00 Sq.m. 40.59
brand and manufacture on new wall surface to give an even shade including
thoroughly brushing the surface free from mortar dropping and other foreign
matter and sand papered smooth for all floors.
108 Wall painting (three coats) with plastic emulsion paint of approved brand and 19291.00 Sq.m. 88.42
manufacture on undecorated wall surfaces to give an even shade including
thoroughly brushing the surface free from mortar droppings and other foreign
matter and sand papered smooth for all floors.
109 Wall painting (three coats) with plastic emulsion paint of approved brand and 10092.00 Sq.m. 97.11
manufacture on ceiling and sloping roofs to give an even shade including
thoroughly brushing the surface free from mortar droppings and other foreign
matter and sand papered smooth for all floors.
110 Providing and applying two coats of acrylic lappy (putty) and two coats of 402.00 Sq.m. 293.09
primer & Wall painting (three coats) with plastic emulsion paint of approved
brand and manufacture on wall surfaces to give an even brushing the surface
free from mortar droppings and other foreign matter and sand papered
111 Providing 20mm thick sand faced Gutka finished cement plaster on walls upto 14847.00 Sq.m. 402.25
all heights above ground level consisting of 12 mm thick backing coat of C.M.
1:3 (1 cement : 3 sand) and 8 mm thick finishing coat of C.M. 1:1 (1 cement :
1 sand) including making grooves 6mm wide and 8mm deep as approved etc.
complete as directed by Engineer-in-charge.
112 Finishing wall with weather proof exterior emulsion paint on wall surface (two 15282.00 Sq.m. 120.26
coats) to give an required shape even shade after thoroughly brushing the
surface to remove all dirt, dust and remains of loose powdered materials etc.
complete for all floors.
113 Providing and fixing 90 cm high Stainless steel railing made from anti 46.00 Rmt. 2110.90
corrosive 304 grade S.S. pipe of 50 mm dia. (16 gauge) as hand rail with S.S.
304 grade baluster of 38 mm dia. (16 gauge) as a vertical support fixed in
RCC slab at 1.2m c/c including three horizontal S.S. pipes of 25 mm dia. (16
gauge) at equal distance fixed by 18.75 mm dia (16 gauge) S.S. pipe with
baluster including accessories as per detailed drawing as directed etc.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
114 Providing and fixing 120 cm high Stainless steel railing made from anti 242.00 Rmt. 3391.58
corrosive 304 grade S.S. pipe of 50 mm dia. (16 gauge) as hand rail with S.S.
304 grade baluster of 38 mm dia. (16 gauge) as a vertical support fixed in
RCC slab at 1.2m c/c including three horizontal S.S. pipes of 25 mm dia. (16
gauge) at equal distance fixed by 18.75 mm dia (16 gauge) S.S. pipe with
baluster including accessories as per detailed drawing as directed etc.
115 Providing and fixing Railing made by 50 x 100mm x 3mm thick pipe for top 870.00 Kg. 131.30
and 50 x 50 x 3mm, 30cm long for supports @ 50cm C/C as per design and
hold fasting with coach bolts including one coat of primer and two coats of
matt finished oil painting etc. complete.
116 Providing and fixing Railing made by 45cm high railing two row 50 x 50mm x 7360.00 Kg. 164.63
3mm thick pipe for top and 50 x 50 x 3mm, 45cm long for supports @ 50cm
C/C as per design and hold fasting with coach bolts including one coat of
primer and two coats of matt finished oil painting etc. complete.
117 Providing, laying and jointing in true line and level I.S.I. mark 15mm dia. 1060.00 Rmt. 72.65
U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in
charge. Pipe shall be fixed on the wall with held of clamp at every two meter
c/c shall be concealed or open as directed including necessary fitting etc.
including testing of pipe and joints and fixing the same with adhesive solvent
including cost of all materials.
118 Providing, laying and jointing in true line and level I.S.I. mark 25mm dia. 1480.00 Rmt. 91.84
U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in
charge. Pipe shall be fixed on the wall with held of clamp at every two meter
c/c shall be concealed or open as directed including necessary fitting etc.
including testing of pipe and joints and fixing the same with adhesive solvent
including cost of all materials.
119 Providing, laying and jointing in true line and level I.S.I. mark 40mm dia. 1186.00 Rmt. 148.12
U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in
charge. Pipe shall be fixed on the wall with held of clamp at every two meter
c/c shall be concealed or open as directed including necessary fitting etc.
including testing of pipe and joints and fixing the same with adhesive solvent
including cost of all materials.
120 Providing, laying and jointing in true line and level I.S.I. mark 50mm dia. 936.00 Rmt. 195.67
U.P.V.C (Sch-40) for cold water including fitting as approved by Engineer in
charge. Pipe shall be fixed on the wall with held of clamp at every two meter
c/c shall be concealed or open as directed including necessary fitting etc.
including testing of pipe and joints and fixing the same with adhesive solvent
including cost of all materials.
121 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 845.00 Rmt. 170.36
C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal
for potable water of following dia. nominal bore tube fittings and clamps
including making good the wall, ceiling and floor etc. complete. (A) 15mm dia.
122 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 1005.00 Rmt. 253.82
C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal
for potable water of following dia. nominal bore tube fittings and clamps
including making good the wall, ceiling and floor etc. complete. (C) 25mm dia.
123 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 420.00 Rmt. 447.72
C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal
for potable water of following dia. nominal bore tube fittings and clamps
including making good the wall, ceiling and floor etc. complete. (E) 40mm dia.
124 Providing and fixing concealed center point to wall ceiling & floor I.S.I. mark 110.00 Rmt. 660.58
C.P.V.C. (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal
for potable water of following dia. nominal bore tube fittings and clamps
including making good the wall, ceiling and floor etc. complete. (E) 50mm dia.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
125 Providing and fixing to wall, ceiling and floor galvanized mild steel tubes 360.00 Rmt. 608.35
(medium grade) of the following nominal bore, tube fittings and clamps
including making good the wall, ceiling and floor (F) 40mm dia.
126 Providing and fixing to wall, ceiling and floor galvanized mild steel tubes 320.00 Rmt. 401.95
(medium grade) of the following nominal bore, tube fittings and clamps
including making good the wall, ceiling and floor (C) 25mm dia.
127 Providing and fixing to wall, ceiling and floor galvanized mild steel tubes 620.00 Rmt. 252.49
(medium grade) of the following nominal bore, tube fittings and clamps
including making good the wall, ceiling and floor (A) 15mm dia.
128 Providing and fixing Heavy Handle valve of approved brand & following 150.00 No. 1284.72
internal dia. of brass including fixing in pipe lines etc. complete (C) 25 mm dia.
129 Providing and fixing Heavy Handle valve of approved brand & following 56.00 No. 1633.17
internal dia. of brass including fixing in pipe lines etc. complete (E) 40 mm dia.
130 Providing and fixing Butterfly valves of IS 13095 with ISI mark PN 1.0 of 29.00 No. 2363.40
approved brand & following internal dia. of brass including fixing in pipe lines
etc. complete (A) 50 mm dia.
131 Providing and fixing to wall, ceiling and floor 10.0 Kg.F/cm2 working pressure 990.00 Rmt. 280.23
polythene pipes of the following outside dia. low density, complete with
special flange compression type fittings, wall clips etc. including making good
the wall, ceiling and floor. (F) 75mm dia.
132 Providing, laying and jointing in true line and level I.S.I. mark 110mm dia. 2000.00 Rmt. 876.90
U.P.V.C. pipe (Type B) confirming to IS 13592-1992 with one end plain and
other end socketed with rubbering & fitting conforming to ISI 14735-1999 of
approved make for drainage system pipe line, pipe shall be jointed with each
other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of
the size 110 mm diameter x 149 mm length x 145 mm height at every
mm center to center or shall be concealed in walls as directed including
necessary fittings such as bends, shoes etc. including testing of pipes and
joints and jointed with adhesive solvent cement including cost of all materials.
133 Providing, laying and jointing in true line and level I.S.I. mark 160mm dia. 1995.00 Rmt. 834.38
U.P.V.C. pipe (Type B) confirming to IS 13592-1992 with one end plain and
other end socketed with rubbering & fitting conforming to ISI 14735-1999 of
approved make for drainage system pipe line, pipe shall be jointed with each
other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of
the size 160 mm diameter x 210 mm length x 196 mm height at every
mm center to center or shall be concealed in walls as directed including
necessary fittings such as bends, shoes etc. including testing of pipes and
joints and jointed with adhesive solvent cement including cost of all materials.
134 Providing and fixing M.S. clamp made from 40mm x 6mm thick M.S. flat as 2120.00 No. 157.56
per design given by Engineer in charge for fixing the C.I. / G.I. / P.V.C. pipe
on wall of duct to stay away from wall etc. complete.
135 Providing and fixing PVC cowl vent of following dia. etc. complete as directed 46.00 No. 126.25
(A) 110mm dia.
136 Providing and fixing PVC cowl vent of following dia. etc. complete as directed 46.00 No. 151.50
(B) 150mm dia.
137 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 390.00 No. 586.27
diameter with jali of the following nominal diameter of self cleaning design
with C.I. screwed down or hinged grating including the cost of cutting and
making good the walls.
138 Providing and fixing C.P. bib cock 15mm dia. heavy duty with cap. 288.00 No. 653.08
139 Providing and fixing C.P. push type bib cock 15mm dia. heavy duty with cap. 72.00 No. 655.36
140 Providing and fixing ball cock of approved quality as directed. (B) Abonite (ii) 12.00 No. 102.91
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
141 Providing and fixing wash basin with single hole for pillar tap with C.I. or M.S. 72.00 No. 2560.35
brackets painted white / fixing in platform including cutting holes and making
good the same including C.P. brass waste and waste pipes and bottle trap &
C.P. pillar cock, 15mm heavy duty swan neck (A) Vitreous china (ii) Flat Back
washbasin 550 mm x 400mm size. (i) in colour. (approved or equivalent brand
142 Providing and fixing S.S. Sink Glossy ASIS 304 grade and 1 mm thick with 26.00 No. 3569.34
over all size 610 x 460mm and bowl size 560 x 410 x 200 mm with single hole
for pillar tap fixing in sandwitch platform including cutting holes and making
good the same, necessary fixtures, connections and waste pipes with C.P.
pillar cock 15mm heavy duty swan neck etc. complete.
143 Provision and fixing water closet squatting Orissa type W.C. pan size 580mm 30.00 No. 1429.15
integral and 100mm P or S trap and including 25mm dia. C.P. brass flush
valve and G.I. inlet connection etc. complete. (A) Vitreous china long pattern
white or color. (Approved or equivalent brand and model)
144 Providing and fixing wash down water closet (European type W.C. pan) with 80.00 No. 3107.77
integral P and trap and PVC flushing cistern, complete with fitting such as
lead valve siphon 15 mm nominal dia. size brass ball valve with polythene
float, C.P. brass handle unions and couplings for connection with inlet outlet
and over flow pipes, 40 mm dia. flush bend including cutting holes in walls
and making good the same connecting the flush bend with cistern and closet
etc. complete including plastic sheet cover including jointing trap with pipe in
C.M. 1:1 (A) Vitreous china in white or colour.
145 Providing and fixing special Needs Range EWC of approved make and model 6.00 No. 65300.54
of size 710 x 370 x 810mm with approved model of S trap, P trap Cistern soft
close seat cover, Twin flush fittings, Wash basin 510 x 400mm. Spatula lever
basin mixer, wall mounted grab bar 600mm long, wall mounted hinged rail
750 x 750 (approved or equivalent brand) as directed by Architect office.
146 Providing and fixing Health Fauset heavy duty with hook with fitting etc. 100.00 No. 822.41
147 Providing and fixing Urinal of approved quality including connection with trap 12.00 No. 1074.86
and with integral longitudinal flush pipe. (A) Squatting plate pattern white
earthenware 550mm x 300mm.
148 Providing and laying Granite slab 18 mm thick in cupboard shelves fixing on 11.00 Sq.m. 2459.35
wall fix and jointed with gray cement slurry including rubbing, polishing, labour
charges, finishing the edges etc. complete as directed.
149 Providing and fixing both side mirror polished granite stone slab 18 mm 13.00 Sq.m. 2202.81
(average) thick of approved quality including full moulded round front edge
fixed in wall for partition and jointed with grey cement slurry including rubbing
and polishing etc. complete.
150 Providing and fixing C.P. angle stop cock 15mm heavy duty with cap etc. 196.00 No. 659.92
151 Providing, erecting and fixing five layer Syntex pure or equivalent 122000.00 Litre 12.12
antimicrobial with active silver technology antifungal, antibacterial, 100% UV
stabilized food grade plastic with FDA approval, multi ribbed design PVC (ISI)
mark water tank of required capacity each with all necessary fittings &
connection etc. complete on terrace.
152 Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass 176.00 No. 859.41
mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden plug
with C.P. brass screws and washers.
153 Providing and fixing C.P. brass towel rail complete with C.P. brass brackets 88.00 No. 616.42
fixed to wooden plugs with C.P. brass scews (B) 600mm x 20mm size.
154 Providing and fixing S.W. Gully trap with C.I. grating brick masonry chamber 67.00 No. 1246.92
and water tight C.I. cover with frame of 300 x 300 mm size (inside) with
standard weight (i) square mouth traps (B) 150 mm x 100 mm size P or R
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
155 Constructing brick masonry chamber for underground C.I. Inspection chamber 26.00 No. 2932.93
and bends with bricks having crushing strength not less than 35 Kg/cm2 in
C.M. 1:5 C.I. cover with frame (light duty) 455mm x 610mm internal
dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of
cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix (1-
cement : 2 coarse sand : 4 graded stone aggregate 20mm size) foundation
concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished
smooth with a floating coat of neat cement on walls and bed concrete etc.
complete. (i) Inside dimensions 455mmx 610mm and 450mm deep for single
pipe line.
156 Constructing brick masonry chamber for underground C.I. Inspection chamber 20.00 No. 3660.76
and bends with bricks having crushing strength not less than 35Kg/Cm2 in
C.M. 1:5 C.I. cover with frame (light duty) 455mm x 610mm internal
dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of
cover 23 Kg.) and Wt. of frame 15Kg.) (R.C.C. top slab with 1:2:4 mix (1-
cement : 2 coarse sand : 4 graded stone aggregate 20mm size) foundation
concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished
smooth with a floating coat of neat cement on walls and bed concrete etc.
complete. (ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe
line with one or two inlets.
157 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1 cement : 2 coarse 18.00 No. 11042.74
sand : 4 graded stone aggregate 20mm nominal size) foundation concrete
1:3:6 mix (1 cement : 3 coarse sand : 6 brick bats 40 + 50mm size) inside
plastering 15mm thick with cement mortar 1:5 (1 cement : 5 coarse sand)
finished with a floating coat of neat cement and making channels in cement
concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 stone aggregate 20mm
nominal size) finished smooth complete including curing and testing (i) Inside
size 900mm x 1200mm and 1.5 M. deep including C.I. cover with frame size
560mm diameter total weight of cover and frame to be not less than 128 kgs.
(Wt. of cover 64 Kg. and Wt. of frame 64 Kg.) (A) With 230mm thick walls of
brick masonry using brick having crushing strength not less than
Kg./Sq.cm. in cement mortar 1:5 (1- cement: 5 coarse sand) (1) A type depth
0.90 metre for 150mm diameter sewer.
158 Constructing manhole with R.C.C. top slab in 1:2:4 mix (1 cement : 2 coarse 2.00 No. 19349.63
sand : 4 graded stone aggregate 20 mm. nominal size, foundation concrete
1:3:6 mix (1 cement : 3 coarse sand : 6 brick bats 40 + 50 mm. size) inside
plastering 15mm. thick with cement mortar 1:5 (1 cement : 5 coarse sand)
finished with a floating coat of neat cement and making channels in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 20mm nominal
size) finished smooth complete including curing and testing. (i) Inside size
900mm x 1200 mm. and 1.5 m. deep including C.I. cover with frame size
560mm total weight of cover and frame to be not less than 128 kgs. (Wt. of
cover 64 kgs. and Wt. of frame 64 kgs.) (A) with 230 mm thick walls of brick
masonary using bricks having crushing strength not less then 35 kg/sq.cm in
cement mortar 1:5 (1 cement : 5 coarse sand) (2) B type depth 1.50 meter for
150 mm diameter sewer
159 Constructing manhole with R.C.C. top slab in 1:2:4 mix (1 cement : 2 coarse 1.00 No. 23470.48
sand : 4 graded stone aggregate 20 mm. nominal size, foundation concrete
1:3:6 mix (1 cement : 3 coarse sand : 6 brick bats 40 + 50 mm. size) inside
plastering 15mm. thick with cement mortar 1:5 (1 cement : 5 coarse sand)
finished with a floating coat of neat cement and making channels in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 20mm nominal
size) finished smooth complete including curing and testing. (i) Inside size
900mm x 1200 mm. and 1.5 m. deep including C.I. cover with frame size
560mm total weight of cover and frame to be not less than 128 kgs. (Wt. of
cover 64 kgs. and Wt. of frame 64 kgs.) (A) with 230 mm thick walls of brick
masonary using bricks having crushing strength not less then 35 kg/sq.cm in
cement mortar 1:5 (1 cement : 5 coarse sand) (3) C type depth 2.25 meter for
150 mm diameter sewer.
160 Providing and laying (to level or slopes) and jointing reinforced concrete light 440.00 Rmt. 678.02
duty non pressure pipes I.S. Class NP-2 of the following internal diameter with
collars and butt ends prepared for collar joints including testing of joints
complete. (D) 300mm dia.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
161 Providing and fixing C.I. manhole cover 0.60m x 0.45m size having weight not 41.00 No. 958.17
less than 35 Kgs.
162 Providing throating or plaster drip and moulding to R.C.C. Chhajja or groove 1068.00 Rmt. 43.05
to plaster.
163 Providing cement vata (10cm x 10cm size) quarter round in cement mortar 1:1 580.00 Rmt. 24.28
including neat cement finishing watering etc. complete.
164 Providing and fixing in position 300 mm high, 300 mm wide English / Gujarati 400.00 Each 707.00
letters made from 1.0 mm thick stainless sheet as directed by Engineer-in-
charge with all necessary tools & plants etc. complete.
165 Providing and fixing in position 150 mm high, English letters made from 1.0 450.00 Each 404.00
mm thick stainless steel sheet as directed by Engineer in charge with all
necessary tools & plants etc. complete.
166 Constructing sand witch platform of 18mm thick Polished Black Granite at top 198.10 Sq.m. 3511.77
and 25mm thick Kota stone slab using cement mortar 1:3 for sand witch and
fitting at bottom & edges with water proof rigid adhesives including making
necessary grooves in walls with Vertical Kota stone 30mm x 2 No. sandwitch
thick every 60 cm center to center or as required including all labour material
of approved quality including full moulded round front edge fixed in wall for
partition and jointed with grey cement slurry including rubbing and polishing
etc. complete for all floors.
167 Constructing sand witch platform of 25mm thick Kota stone slab using cement 46.00 Sq.m. 2245.23
mortar 1:3 for sand witch and fitting at bottom & edges with water proof rigid
adhesives including making necessary grooves in walls with Vertical Kota
stone 30mm x 2 No. sandwitch thick every 60 cm center to center or as
required including all labour material of approved quality including full
moulded round front edge fixed in wall for partition and jointed with grey
cement slurry including rubbing and polishing etc. complete for all floors.
168 Providing, laying & fixing 50mm thick expansion joint by hydro cell semi rigid 323.00 Sq.m. 1491.03
UV resistance with high performance laminated closed cell polythene foam
joint filler in sheet foam as directed etc. completed.
169 Providing and filling the expansion joint by polymer confirm to BS 4254-1983 987.00 Rmt. 515.39
as per required shade and manufactured specification by making groove of
50mm x 12.5mm lather by cutting or by repairing groove and removing mortar
drop or any other foreign material including applying primer and filling
required size (over size of joint PU foam) as directed etc. complete.
170 Providing and fixing 25 cm Wide & 3mm thick exterior composite panel on 155.00 Sq.m. 1054.34
existing expansion joint horizontally & vertically with all material, hardware,
accessories & fittings etc. completed.
171 Providing and fixing copper strip and holdfasts for to cover expansion joint 134.00 Rmt. 8952.64
copper sheet of 1.25mm thick and of 1250mm width with the U shape in the
middle, Copper strip shall have holdfast of 3 mm diameter copper rod fixed to
the plate soldered on strip at intervals of about 30cm etc. complete.
172 Providing and fixing One Row 50 mm dia. stainless steel railing made from 169.00 Rmt. 1310.98
anticorrosive 304 grade as hand rail fixed in railing with necessary support
including accessories as per detailed drawing as directed etc. complete.
173 SIGNAGES ON DOOR : 254.00 No. 656.50
Providing, fabricating and fixing 304 grade stainless steel 1.5mm thick
brushed steel finish plate fixed on a door using S.S studs and with punched
(laser cut) lettering carried out on S.S plate of required size and text as
directed by engineer etc. complete. Size 12" x 6"
174 Providing and fixing writing board 4 x 6 ft. size with glass board dull finished 21.00 No. 4646.00
green sheet with 100 x 25mm teak wood frame of 25mm thickness with french
polish etc. complete.
175 Providing and fixing stainless steel / Alluminum pipe approved pattern and 98.00 Rmt. 202.00
size for windows curtain including fixing in line and level as directed by
Engineer in charge.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
176 Providing and fixing Decorative stainless steel brackets approved pattern and 120.00 No. 757.50
size for windows curtain including fixing in line and level as directed by
Engineer in charge.
177 Providing and laying Kota stone slab 25mm thick in cupboard shelves resting 447.00 Sq.m. 707.00
on wall fix and jointed with white cement slurry including rubbing, polishing,
labour charges, finishing etc. complete as directed.
178 Providing and fixing steel cupboard having frame of 40 mm x 40 mm x 5 mm 409.00 Sq.m. 3149.18
M.S. angle double door shutter of CRS plate of 18 gauge (1.219 mm
thickness) with 30 mm x 3 mm x 3mm angle framing at top and bottom edge
of shutter 10 mm x 10 mm square M.S. bars 2 Nos. vertical and 40 mm x
mm M.S. flat at one edge of each shutter and for lock along with one coat of
red oxide and two coats of spray oil painting of approved brand and colour
shed and locking arrangement etc. complete as directed by Engineer-in-
179 Providing and fixing coloured self adhesive PU - Tactile tiles, ground surface 120.00 Sq.m. 4586.41
indicators of Polyurethane of size 300 mm x 300 mm for guiding / warning to
the visually visitors in the centre / side of the pedestrian / approach pathway
as per specification and guidelines complete in all respect to the entire
satisfaction of in charge.
180 Providing and fixing acrylic multilingual Braille (raised dots) DIRECTIONAL 32.00 No. 1696.80
SIGNBOARDS of size 225 x 150mm designed as per accessibility standards
and having 3.5mm thick acrylic base plate with Upper Case San Serif words
made of white acrylic non glare cut out letters of height 15mm raised not less
than 0.8mm above base plate and the equivalent word written in Hindi with
Devanagari non glare acrylic letters of height 15mm raised not less than
0.8mm above base plate and having a non-glare acrylic cut arrow pointing in
the required direction. Each signboard to be fixed as per manufacturers
specifications on the wall at the approved location and at a height of 1200mm
from FFL complete as per design / specifications and guidelines as per the
entire satisfaction of the Engineer-in-charge.
181 Providing & fixing tactile layout plan of size 900mm x 600 mm as approved 1.00 No. 33027.00
design, made of 3.0 mm thick acrylic non glare base plate and non glare cut
out symbols with braille on which individual facility points, like inquiry,
reception, rest rooms, medical room / first aid, cafeteria or breakout area,
lounge meeting room, conference room etc. present the respective floors with
pictograph wherever needed all in tactile raised by minimum of 1.0 mm to
mm in various colours to make it legible for senior, partial vision impaired etc.
all the facility names should be braille, along with English or Hindi. Entire
block of tactile sign should be mounted on wall for easy reading. The map to
be installed at specified locations and installed at a height of 800 mm from
ground level complete in all respect as per hormonized guideline &
satisfaction of engineer in charge.
182 Providing and fixing of acrylic, non-glare, tactile audio pictorial building layout 4.00 No. 43480.50
as per the approved size, design and make, having 3mm thick acrylic non
glare base plate of the approved colour and non-glare acrylic cut out symbols
raised 3mm above base plate and Grade 2 / Grade 1 Braille to be integral with
the sign face and be raised 0.5mm above base plate. The map to be installed
at the specified location as per accessibility standards, shall be oriented to the
position of the viewer and to be installed at a height of 800 mm from the
finished ground/ floor level and using the necessary hardware specified by the
manufacturer and to be installed up to the height of 800 mm from the finished
ground/ floor level and using the necessary hardware specified by the
manufacturer and to be installed complete as per design / specifications and
guidelines as per the entire satisfaction of the Engineer-in-charge.
183 Providing and fixing Braile Indicator of size 170 mm x 35 mm for hand rails of 222.00 Sq.m. 819.11
the approved design and make have braile dots raised 0.5 mm above base
plate to be installed at specification as per direction of Engineer in charge.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
184 Providing and fixing conspectus tape 50 mm width on of treads in staircase 500.00 Sq.m. 1247.35
including cutting pasting etc. as per harmonised guidelines complete in all
respect to the entire satisfaction of Engineer in charge.
185 Providing and fixing 15 mm thick 300 mm x 300 mm Tactile Warning Tiles 110.00 Sq.m. 1205.94
(Attention Tiles i.e. Tactile Warning Surface Indicator {TWSI}) of Johnsan
Endura Tac Button Yellow Plus or equivalent make in flooring laid on 20 mm
thick cement mortar 1:6 (1 cement : 6 coarse sand) on new surface and
jointed with cement slurry including finished with flush pointing & cleaning the
surface for all floors as per detailed drawing etc. complete as directed by
Architect or Engineer in charge. These tiles shall be Anti Skid, Chemical
Resistant, Fade Proof, Frost - Heat & Weather Proof, High Flexural Strength,
Highly Durable, Stain Resistance. All Tactile Warning Tiles meet the specific
size and dimension standards as required by ISO/FDIS
186 Steel work, welded in built up sections framed work including cutting, hoisting, 129.00 Qtl. 9655.60
fixing in position and applying a priming coat of red lead paint. (D) In trusses
and trussed purlins, upto 25 M. span and 15 M. ovarall height.
187 Providing corrugated PPGL sheets 0.62mm thick / 1.5mm thick transparent 994.00 Sq.m. 929.20
acrylic sheet (70% / 30%) roofing fixed with galvanised iron 'J' or 'L' hooks,
bolt and nuts 8mm dia. with bitumen and G.I. limpet washer filled with white
lead complete including ridges, gutters etc. excluding the cost of purlins,
rafters and trusses. (1) 0.60mm thick sheet.
188 Providing and fixing hard drawn steel wire fabric 75mm x 25mm mesh of 354.00 Sq.m. 484.80
weight not less than 7.75 Kg. per Sq.m. to windows grill etc. including fixing
with M.S. flats and welding including painting two coats with red lead paint.
189 Providing and fixing CUPBOARD shutters using 19 mm thick waterproof (ISI 129.00 Sq.m. 2364.41
710) and 1 mm thick laminate inside & 20 mm x 2 mm T.W. facing batten and
T.W. frame having a size 7 cm x 4 cm using necessary fixtures, fastening,
nails, fevicol, ball catch, magnet and inner side of cupboard oil painting two
coats with primer coat etc. complete as per detailed drawing.
190 Providing and fixing drawer type kitchen basket cup board using T.W. Frame 46.00 Sq.m. 14449.06
having size 5 cm x 3.2 cm and using 19 mm thick water proofing plywood ISI
710, 1 mm thick laminate inside, SS Telescopic 550 mm SSF channel
{Hattich or equivalent brand} brass, SS fixtures and fastening handles as
approved quality including using necessary screws, fevicol, T.W. batten facing
20 mm x 6 mm patti for plywood including fixing SS {304} basket of 17" x 20"
{3 square, Evershine or equivalent brand} (1) For Plain multi purpose 100mm
(2) Plain Multi purpose 150 mm (3) Cup soucesser 100mm (4) Partition
mm (5) Partition 150 mm, (6) Cutlery 100mm (7) Plate 150 mm (8) Thali
mm (9) Vegetable Plain 150 mm (10) Bottle Basket 150 mm (11) Pull out
mm including fixing SS Telescopic channel as per approved quality and given
detailed drawing.
191 Providing and fixing 50 x 100 mm x 3 mm thick pipe for frame & 30 mm dia. 3 4605.00 Kg. 100.19
mm thick M.S. pipes @ 15 cm C/C in M.S. frame as per design and hold
fasting with coach bolts including one coat of primer and two coats of matt
finished oil painting etc. complete.
192 Providing and fixing Balcony (Invisible) Grill with following specifications 220.00 Sq.m. 1363.50
Grill Design: Antique
Size: Bolts gapping - 50mm, Material Grade: 2.00 mm thickness aluminum
alloy T6061
Stainless Steel 304 Bolts with Nylon washer Material: Stainless Steel
Wire Diameter : 2.50mm
316l Marine Grade - Grater Corrosion Resistance 2.50mm, Tensile Strength :-
3920 Newton - 4900 Newton 400kg-500kg
Coating :- Copolymer nylon, teflon, nano technology nylon
193 Providing and laying controlled cement concrete M-200 for R.C.C. work and 32.60 Cum 5914.56
curing complete including the cost of form work but excluding cost of
reinforcement for reinforced concrete work in Sills on Ground floor.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
194 Providing & casting in situ ordinary cement concrete M-150 mix and providing 1884.00 Cum 3917.21
necessary pin headers including shuttering, scaffolding, laying, vibrating,
curing and finishing complete without V-Grooves. (A) Height from 0.0 M. to
195 Providing and fixing Name plate of mirror polished granite stone by engraving 4.50 Sq.m. 5050.00
and painting letter with golden colour and fixing with decorative patta pattern
as directed by engineer in charge.
196 Providing and fixing M.S. gates / Grill of required pattern to brick walls / 20858.00 Kg. 166.65
Columns prepared with M.S. flats 50 x 6mm and 50 x 50 x 3 mm Square
pipes, at required spacings with necessary hold fasts as per detailed drawing
and fixing brick walls / coping / columns etc. complete including painting two
coat & applying primer coat. (A) Ornamental Grill
197 Constructing cattle trap made from ISMC 100 border and G.I. pipe 50 mm dia. 10.00 Sq.m. 3816.79
HEAVY DUTY at 12 cm spcaing by welding and for support 2 Nos I.S.M.C.100
x 75 x 6 section fixing in prepard chamber as per drawing by necessary
arrangement etc. complete.
198 Providing and fixing RAZOR Coil with blade 16mm, Clips per Spiral-5, Hot 440.00 Rmt. 611.05
Dipped Galvanized 200 GSM, Tape thickness 0.50 MM, GI Spring Core Wire
2.60mm thick {avg weight 9.50 Kg /6 mt} and 5 Rows of galvanised steel
barbed wire weighing 9.38 Kg. per 100 Metre in M.S.angle posts 45 mm. x
mm. x 6 mm. and oil painting 3 coats fixed at 3.0 mt. C/C strained and fixed to
posts with G.I. staples including fixing posts in compound wall.
199 Providing and laying controlled cement concrete M-200 and curing complete 69.50 Cum 4225.84
including the cost of formwork and excluding reinforcement for reinforced
concrete work in (A) Foundations, footings and Mass concrete.
200 Providing and fixing mild steel door with 40 x 40 x 6 mm angle for frame and 1360.00 Kg. 64.14
for shutter frame 30 x 30 x 3 angle for windows frame of angle 35 x 35 x 5 &
for shutter windows 25 x 25 x 3 mm size angle and 18 gauge sheet for panels
& 10 mm dia bars at 10 cm c/c for grill and 40 x 6 mm flats on edge of
shutter & 20 x 6 mm binding patti including one coat of primer and two coats
of oil painting etc. complete as per detail / as directed by Engineer in charge.
201 Providing and laying white glazed tiles 6 mm. thick in flooring treads of steps 168.00 Sq.m. 890.26
and landings laid on a bed of 12 mm. thick cement mortar 1:3 (1 cement :
coarse sand) finished with flush pointing in white cement.
202 Providing and laying white glazed tiles 6 mm. thick in skirting, risers of steps 420.00 Sq.m. 993.83
and dedo on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand)
pointing in white cement and jointed with white cement slurry.
203 Distempering (three coats) with oil bound distemper of approved brand & 516.00 Sq.m. 104.22
manufacturer & of required shade on wall surfaces to give an even shade,
over & including a primary coat with alkali resistance primer of approved
brand after thoroughly brushing the surface free from mortar dropping & other
foreign matter & also including preparing the surface even & smooth.
204 Supplying cutting, bending, binding and placing in position T.M.T. bar 7.07 M.T. 78279.04
confirming to Fe-500D grade as per plan and design and as per ISS
including cost of steel and binding wire for reservoirs only including lift upto
mt. height./ depth below G.I. for all diameters.
205 Providing and cast in situ C.C. in grade M-25 proportions of ingredients as per
mix design by weigh batching using granite, quartizite, trap metal of size
mm to 20 mm and or 6 mm to 12 mm including scaffolding, centering, form
work, needle vibrated consolidation. Up to 6.00 mts. depth or height.
(A) For Raft footing 10.70 Cum 6772.05
(B) Brass brace 5.40 Cum 8430.47
(C) Columns 7.60 Cum 9286.95
6.00 to 9.00 mt. height
(A) Brass brace 2.70 Cum 8637.52
(B) Columns 2.90 Cum 9494.00
(C) Slab with immediate finish for inspection 2.10 Cum 8364.82
9.00 to 12.00 mt. height
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
(A) Columns 2.20 Cum 9701.05
(B) Bottom ring Beam of container 5.10 Cum 8844.57
(C) Bottom dome of container 7.40 Cum 8571.87
12.00m to top of Tank
(A) Vertical wall (above 150mm and upto 200mm excluding chambers) 16.00 Cum 8910.22
(B) Roof dome 3.70 Cum 8778.92
(C) Top ring beam of roof dome 1.30 Cum 9051.62
206 Providing cement plaster 20 mm thick in C.M. 1:2 using water proofing 193.00 Sq.m. 204.02
compound of approved quality including finishing etc. complete.
207 Providing & fixing C.I. Cowl type ventilator with air filter & jali etc. complete all 60.00 Kg. 61.61
208 Providing 50 cm wide M.S. ladder fabricated from M.S. Flats 10 mm x 75 mm 20.00 Rmt. 2979.50
with 20 mm dia steel bar steps, in double rows @ 30 cm C/C. The include
stays of 10mm x 50 mm flats fixed at 3 meter C/C with welding anchoring and
3 coats of anti corrosive paints.
209 Providing M.S. railing made of three horizontal rows - top rail of L 50 x 50 x 6, 1101.00 Kg. 70.70
central rail of 50 x 6 thick flat and toe plate of 100 x 6th flat and vertical posts
of L 50 x 50 x 6 mm -1m high supported on RCC pedestal of 150 mm x
mm and placed not exceeding 2m C/C. including two coats of enamel painting
etc. complete as per drawing specified.
210 Providing and fixing flanged steel cylinder reinforced concrete or CIDF class A 60.00 Rmt. 3139.08
pipe vertically for RCC reservoir including providing clamps at every three
meter including jointing material such as nuts bolts rubber packing hydraulic
testing and necessary 100 mm dia. for cap above 70 Cum
211 Manufacture, supply and delivery of 80 mm to 700 mm dia. cast iron plain 300.00 Kg. 58.58
ended specials complete as per IS: 5531-1977 (Part- I to III) or its latest
revision if any, suitable for use with A.C. pressure pipes manufactured as per
IS: 1592-1989 or its latest. (A) C.I. Specials 100 mm dia.
212 Providing, supplying, lowering laying and jointing in position ISI mark CI D/F 3.00 No. 4357.14
Sluice valves, butterfly valves & reflux valves of following class and diameter
including all taxes, insurance, transportation, freight charges, octroi,
inspection charges, lo Sluice valves with ISI mark only PN 1 with hand wheel /
cap operated. (B) 100 mm dia. pipe - Inlet pipe, Outlet pipe & Over Flowpipe.
213 Construction of valves chambers in brick or bela stone masonry, locally 3.00 No. 5331.79
available in C.M. 1:6. Foundation concrete 150 mm thick in C.C. 1:4:8 of black
trap metal size 25 mm to 40 mm thick, inside cement plaster in C.M. 1:3 and
cement pointing outside in C.M. 1:3 and top cover of precast RCC slab
mm thick / with key hole in two parts, each with handles or MS bar etc.
complete as given size) Upto 1 Mt. depth from G L to pipe invert level
including complete civil works but excluding cost of excavation and refilling,
with cast in situ RCC slab in one single piece with fixing of CI - MH frame and
cover (excluding cost of CI - MH frame and cover) with 23 mm thick brick
masonry wall in C.M. 1:6 Size of chamber 0.60 m x 0.60 m and 1.0 mt. deep.
214 Providing and fixing depth gauge painted on TW plank 25 mm / MS plate 4 1.00 No. 5575.20
mm thick with float, level indicator sliding wire on standard pullies including
necessary arrangement to prevent the swinging etc. complete with calibration
upto 5 mt. height.
215 Providing and fixing copper lightening arrestor including copper strip and 20.00 Kg. 886.78
earthing plate etc. complete (including cost of excavation for earthing plate
etc. rate per kgs of copper). 1200 High lighting.
216 Painting, letters with enamelled paint for "Capacity of tank" the size of letters 50.00 No. 34.34
will be 45 cm height and 50 mm width.
217 Providing and supplying C. I. Manhole frame & cover. 50.00 Kg. 61.61
218 Providing and laying cement concrete 1:2:4 laid in one layer finished with 42.00 Sq.m. 297.31
floating coat of neat cement. 40 mm thick
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
219 Providing and cast in situ C.C. in grade M-25 proportions of ingredients as per Cum
mix design by weigh batching using granite, quartizite, trap metal of size
mm to 20 mm and or 6 mm to 12 mm including scaffolding, centering, form
work, needle vibrated consolidation.
(A) RCC coping 0.40 Cum 4432.89
(B) Lintel 0.20 Cum 4432.89
(C) Stair room roof slab 0.90 Cum 4432.89
220 White washing with lime on wall surface (three coats) to give an even shade 34.00 Sq.m. 18.55
including thoroughly booming the surface to remove all dirt, dust; mortar
drops and other foreign matter.
221 Providing and fixing 1 mm thick MS sheet door shutters with frame and 1.90 Sq.m. 3916.47
diagonal braces of 40 x 40 x 6 mm with handles, stoppers and locking
arrangement etc including applying a primer coat of red oxide paint etc
222 Clearing and grubbing road land including uprooting rank vegetation grass 1.11 Hect. 34889.38
bushes, shrubs, sapling and trees girth up to 300 mm removal of stumps of
trees cut earlier and disposal of unserviceable materials (C) By mechanical
means in area of light jungle.
223 Earthwork in cutting in all sorts of soil and soft murrum including conveying 1166.00 Cum 134.13
and spreading the stuff, embankment as and where directed within
meters from the end of the cutting with all required lead and lift.
224 Earthwork in cutting including preparing the slope, camber and stacking or 9324.00 Cum 260.57
utilising the cutting stuff in bank as directed upto 200 meters from the end of
cutting with all lead and lift. (ii) Hard murrum.
225 Earthwork in cutting including preparing the slope, camber and stacking or 11655.00 Cum 317.35
utilising the cutting stuff in bank as directed upto 200 meters from the end of
cutting with all lead and lift. (ii) Soft rock not requiring blasting.
226 Earthwork in cutting including preparing the slope, camber and stacking or 1166.00 Cum 673.13
utilising the cutting stuff in bank as directed upto 200 meters from the end of
cutting with all lead and lift. (iii) Hard rock.
227 Rolling & watering of earthwork in layers with vibratory roller including filling in 1540.00 Cum 22.96
depressions which occurs during the process.
228 Conveying and utilising the stuff in bank from end of cutting with all required 12351.00 Cum 99.97
lead and lift.
229 Box cutting the road surface to proper slop and camber for making a base of 756.00 Cum 109.41
road work including removing the excavated stuff and depositing on the road
side slope as directed for all lead and lift.
230 Providing and laying W.B.M. of B.T.M.C. metal of size 45 mm to 63 mm size 528.00 Cum 2143.22
including 20% grit {Stone screening} & stone dust as filler including
spreading, watering & consolidation by vibratory roller 80KN to 100KN static
231 Providing and laying controlled cement concrete M-250 for C.C. Road / 756.00 Cum 6021.62
wearing coat with polyester fiber (12mm) with triangular of equivalent cross
section with specific gravity 1.35 to 1.40 (as a secondary reinforcement) in
concrete of any grade at the rate of 125 gms per 50 kg of cement
consumption and curing including cost of formwork, compaction and finishing
of cement concrete road by trimix vacuum dewatering process on cement
concrete road surface by using vacuum dewatering pump, surface floater,
surface vibrator including channelling and making grooves and rough finish to
surface by providing expansion joints, construction joints and filling of joints
with asphalt filler as directed by Engineer in charge and as per specification.
232 Excavation for foundation upto 1.50 mt depth including sorting out and 221.00 Cum 122.94
stacking of useful materials and disposing the excavated stuff within all lead
and lift for loose or soft soil.
233 Painting lines, dashes, arrows, letters, etc. on roads, air fields and like in two 571.00 Cum 129.29
coats with road marking paint Brushing including cleaning the surface of all
dirt, dust and other foreign matter. (I) Over 10 c.m. in width
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
234 Lawn Grass :- Filling the area upto the depth of 23 cm. with good quality of 1505.00 Cum 211.71
field fertile soil, breaking the clods leveling the area, free from stone, grass
roots etc. and farm yard manure at the rate of 5 cu.mt. per 100 sq.mt. mixing
the same with layer of soil, leveling rolling, pre- planting, watering etc. and
planting the lawn grass of approved variety at 10 x 10 cm. distance etc.
complete as per detail specification and maintenance for 3 months.
235 Plantation of trees in soil including digging 45 x 45 x 45cm size pits, preparing 400.00 No. 25.25
soil, providing and mixing organic fertiliser, watering, planting and filling the
pits as per direction including etc. complete.
236 Providing Tree Plants having minimum 1.00 mt height and healthy growth of 400.00 No. 15.15
various kinds as like Peltoform, Gulmahore, Karanj, Ambla, Rain tree, Cherry,
Cryjeliya, Spethodiya, Paras Pipala, Garmalo, Neem, Borsalli, Kadam, Buch,
Champo, Asopalav etc. as per instruction by engineer in charge.
237 Maintenance of planted tree upto Two years including watering, digging pits, 400.00 No. 277.75
trimming applying fertilizer, insecticide, pesticide and pesticides and replacing
plants if necessary etc. complete for raising of plants weeding or soil working
also including maintaining Water supply lines and drip lines of Plantation
(Water and Electricity supply by Deptt.)
238 Providing and fixing TREE GUARD 2.00 mt. long & of 600mm dia. square 400.00 No. 967.58
mesh of 2” x 2” and M.S. flat of 25mm x 5 mm vertical support and three rings
of 20 x 3 mm flat, fixing on site in C.C. 1:4:8 and including oil painting two
coats with red lead priming coat.
239 Providing, erecting and fixing double coated I.S.I. Mark P.V.C. water tank of 2000.00 Litre 3.95
required capacity each with all necessary fittings and connection etc.
complete on terrace as directed.
240 Providing and erecting open well type horizontal monoblock pumpset with C.I. 2.00 No. 6817.50
body having following specification (I) 1 H.P. single phase open well motor
pumpset suitable for 145 ltr / min (ii) suitable for 32 dia. delivery pipe with
control panel & 10 m.
241 Providing and fixing Drip Irrigation system of approved brand for plantation No.
including fixing with water supply line and plantations per drawing and
requirement.
Screen filter 7000 Ltr per Hr 2.00 No. 1464.50
Presure guage 1" dia (0 - 7 Kg/cm2) 2.00 No. 313.10
Bypass assembaly Gun metel 2.00 No. 1818.00
32 mm control valve Gun metal 2.00 No. 323.20
16 mm lateral HDPE pipe 2.5 kg including fitting and Micro Tibe / Dripper etc. 1000.00 Rmt. 8.89
1.2 mm Micro tube 400.00 No. 1.82
Dripper 4 LPH / 8 LPH 400.00 No. 1.82
242 Drilling of 200 / 215 mm dia. bore well in over burden rocky or loose 150.00 Mtr. 418.14
collapsible / boulder strata & lowering of 175 / 200 mm dia. UPVC / PVC /
ERW casing pipe above 12 meters and upto 40 meters depth by DTH rig etc.
243 Supply of clay balls having size of 15mm to 25 mm made from sticky clay on 20.00 Cum 758.51
244 Supply of ERW blank pipe of approved quality at site of work confirming to IS: 50.00 Rmt. 2431.07
4270/2001 200mm internal dia. for housing 6 mm thick
245 Supply of ERW slotted pipe of approved quality at site of work confirming to 30.00 Rmt. 2626.00
IS: 4270/2001 200mm internal dia for housing 6 mm thick
246 Jointing ERW pipes blank or slotted by solding including cost of jointing with 80.00 Rmt. 25.25
materials and champlas sets.
247 Supply of gravel having size 4mm to 6 mm as directed on site. 25.00 Cum 2049.29
248 Providing and fixing E.R.W. bail plug reducer steel bent plates, welding rod, 1.00 L.S. 5454.00
supporting clamps etc. as per requirement 0.60 mt. long and 200mm dia.
249 Heavy duty clamp made from 4" x 1.5" iron strip suitable for column pipe 1.5" 1.00 No. 212.10
to 2" length. (B) 50mm (2") dia pipe.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
250 Supplying & erecting G.l. bend for pipe connections suitable for (D) 50 mm 1.00 No. 135.34
251 Supplying & erecting C.I. swing, check type non- return (Reflux) Valve ISI 1.00 No. 1201.90
marked suitable for following size (C) 50 mm dia.
252 Charges for development of bore by giving air with compressor for 1.00 L.S. 22427.05
requirement as per site situation {600 CFM / 150 PSI upto the any depth,
minimum 6 hours}
253 Supplying submersible pump set for bore of 150 mm. dia.or more having 3 2.00 No. 39693.00
phase motor capacity 10 H.P. and having [B] 20 stage 210 to 160 LPM
discharge at 148 to 173 mtr head for 50 mm dia delivery pipe. Cat III
254 Supplying & erecting approved make 3 phase motor control cubical panel 1.00 No. 14594.50
(Star - Delta) made from16 G. CRCA sheet duly painted with epoxy power
painted inside and outside with hinged doors and locking arrangement,
consisting of suitable size of ON- OFF isolator (AC - 3/23 duty) main fuses,
single phasing preventor cum water level. Guard (Complete unit), Toggle
switch to bypass single phase preventer cum WLG, indicating lamps for R- Y-
B phases, over load relay, Automatic water level controller, Ammeter &
Crimped, Panel to be erected on angle iron frame grouted on wall as directed.
Star Delta & main contactor, overload relay, thermal / Electronic Star delta
cutoff timer, start - stop push buttons. The isolator overload relay & contactors
of L&T, Siemens or Cuttler Hamer make only. Panel to be erected on angle
iron frame ground on wall. (b) S/D up to 10 H.P.
255 Lowering of submersible motor pump set complete with required. Nos. and 1.00 Job 3535.00
size of casing pipes erected by means of proper chain pulley block & pipe
wrenches after checking of threads of each pipe with coupling to take the load
of the pump set and pipe assembly filled up with water. (C) Above 120 mtr.
256 Providing and erecting ISI marked PVC insulated PVC Shethed Flat flexible 300.00 Rmt. 153.52
Submersible copper cable approved make of following size. (d) 3 Core x 4 Sq.
257 Supplying ISI Marked (Embossed) following size of Heavy duty "C" Class G.I. 100.00 Rmt. 418.14
pipe & erecting as directed by Engineer-in-charge with necessary plumbing as
desired. (D) 50 mm dia. (Jindal, Asian, Tata make or equivalent make only)
258 Supplying and erecting with leak proof materials, M.S. Heavy duty ISI marked 30.00 No. 107.06
coupling having threads of 8 TPI/11 TPI suitable for 'C' class pipe to take load
of pump and pipe assembly of following size and TPI (C) 50 mm (2") dia. pipe
259 Add cost of leak proof complete welding surrounding pipe and coupling for 30.00 No. 70.70
use as column pipe for following size (A) 50mm
260 Cutting the heavy duty pipe and threading one end of pipe with 8 TPI / 11 TPI 30.00 No. 81.81
as per requirement and including to and fro charges. (B) 50mm (2") dia pipe.
261 Geological ground water investigation charges. 1.00 Job 14428.86
262 Water sample chemical analysis charges 1.00 Job 606.00
263 Providing and construction of Junction chambers of size 0.35 x 0.35 x 0.60 40.00 No. 1502.88
mt. with foundation concrete in C.M. 1:2:4 10 cm thick, half brick masonary
wall in C.M. 1:4, 50 mm thick flooring in C.C. 1:2:4 inside plaster 15 mm thick
in C.M. 1:4 including connecting of rainwater pipe as per detailed drawing and
as directed by Engineer in charge.
264 Providing and constructing filter chamber of size 2.06 x 1.21 x 1.20 mt. with 3.00 No. 12694.69
Foundation Concrete in C.M. 1:2:4 12.5 cm thick, 23 cm thick brick masonary
in C.M. 1:6, Half brick masonary partition wall in C.M. 1:4, inside plaster
mm thick in C.M. 1:4 and cover slab 10 cm thick in C.M. 1:2:4 with necessary
reinforcement and filling 30 cm with 25 to 40 mm size Kapachi and coarse
sand for 90 cm as directed including connection rainwater pipes as per
detailed as directed by Engineer in charge including cost of labour and
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
Electrical Items
265 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 1709.00 Pt 485.81
(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi
strand copper wires up to 10 mtr length, in below type of pipe erected with 6A
Modular type switch / bell push & accessories and earth continuity of following
type, erected on PVC / Metallic / Wooden box, single mounting base frame
covered with textured / metallic / white front plate modules erected on / in wall
/ ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.
Connector as directed.(f) with medium class Rigid PVC pipe and accessories
erected concealed in wall / ceiling complete. Cat. III
(f) with medium class Rigid PVC pipe and accessories erected concealed in 36.00 Pt 242.91
wall/ceiling complete Cat. III (Half Point for Bathroom and WC)
266 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both 466.00 Pt 674.68
are of ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper
wires up to 10 mtr length, in below type of pipe erected with 6A Modular type
switch and hum free EME step type electronic fan regulator mounted and
accessories with earth continuity of following type erected on PVC / Metallic /
Wooden box, single mounting base frame covered with textured / metallic /
white front plate modules erected on / in wall / ceiling as per pipe erected.
with necessary ceiling rose / H.D.Connector as directed. (f) with medium class
Rigid PVC pipe and accessories erected concealed in wall/ceiling complete
267 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both 171.00 Pt 510.05
are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper
wires up to 10 mtr length, in below type of pipe erected complete with
Modular type switch & 5 pin Plug erected on PVC / Metallic / Wooden box
covered with appropriate front plate modules erected on / in wall / ceiling as
per pipe erected with following type of accessories. [I] For 6A Plug and 6 a
switch with 2-1.5 sq.mm Cu. Wire from nearby switch board/mcb db board (f)
with medium class Rigid PVC pipe and accessories erected concealed in
wall/ceiling complete Cat. III
[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db 23.00 Pt 745.38
board. (f) with medium class Rigid PVC pipe and accessories erected
concealed in wall/ceiling complete Cat. III
268 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin 1040.00 Pt 257.55
socket erected on PVC / Metallic / Wooden box, single mounting base frame
covered with textured / metallic / white front plate modules erected on / in wall
/ ceiling with following type accessories Cat. III
269 Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire 86.00 Pt 603.98
of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade FRLS PVC
insulated multi strand copper wires erected in below type of pipe with 6A
Modular type switches and following type of accessories erected on PVC /
Metallic / Wooden box, single mounting base frame covered with textured /
metallic / white front plate modules erected on / in wall / ceiling as per pipe
erected with necessary batten/angle holder or ceiling rose or H.D. Connector
as directed.(f) with medium class Rigid PVC pipe and accessories erected
concealed in wall/ceiling complete Cat. III
270 Providing following type of Modular Type Accessories mounted with PVC / 168.00 Ea 151.50
metallic / Wooden box, single mounting base frame covered with textured /
metallic / white front plate, modules erected with necessary connections as
per site situation directed by Engineer In charge.(1) One No. SP 6 Amp.Cat.
(2) One No 5 pin plug Cat. III 168.00 Ea 151.50
(3) Two Pin/RJ-11 Telephone Socket [A] For One Gang Cat. III 100.00 Ea 160.59
(4) TV Co-axial Socket outlet Cat. III 15.00 Ea 160.59
(5) Electronic hum Free steps EME Fan regulator Cat. III 24.00 Ea 398.95
(7) Blank Plate Single Cat. III 1207.00 Ea 25.25
(8) Computer RJ-45 socket Cat. III 71.00 Ea 160.59
(9) 16 Amp. SP one way switch Cat. III 216.00 Ea 180.79
(10) 6/16Amp. Universal socket Cat. III 243.00 Ea 199.98
(14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch Cat. III 27.00 Ea 410.06
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
(21) Foot Light as per colour requirement with concealed box, modular 33.00 Ea 494.90
accessories, acrylic glass cover with suitable LED watt with all accessories as
per following module (b) Four modules Cat-III
271 Providing & erecting following type of Modular Type Accessories with 142.00 Ea 36.36
necessary connection as desired by Engineer In charge (5) LAN cable
connector with ferule
272 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following 5052.00 Mtr. 24.24
size complete to be erected on/in wall or ceiling erected with necessary PVC
fittings & Junction boxes fixed with adhesive solution & Clamps with following
dia of pipes, in approved manner as directed (a) 20 mm
(b) 25 mm 1203.00 Mtr. 33.33
(c) 32 mm 460.00 Mtr. 54.54
273 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 15161.00 Mtr. 82.82
marked stranded Copper conductor wire in following type of pipe to be
erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper
conductor FRLS PVC insulated stranded wire of green colour for earth
continuity of following size (A) With medium class Rigid PVC pipe and
accessories (b) 2 wire 2.5 sq. mm
274 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 5598.00 Mtr. 112.11
marked stranded Copper conductor wire in following type of pipe to be
erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC
insulated stranded wire of green colour for earth continuity of following size
(A) with medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm
(b) 2 wire 6 sq. mm 535.00 Mtr. 147.46
(h) 4 wire 6 sq. mm 837.00 Mtr. 260.58
(i) 4 wire 10 sq. mm 460.00 Mtr. 425.21
275 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi 103.00 Mtr. 37.37
stranded, annealed copper conductor with heat resistant PVC insulated
conforms to IS 694, IEC - 227 erected in existing pipe of following size
(Specifically for control panel, relays, power switchgears, motor starters &
control wiring) with required size of copper lugs, nuts and bolts if required. (d)
One wire 4.00 sq. mm
(e) One wire 6.00 sq. mm 196.00 Mtr. 56.56
(f) One wire 10.00 sq. mm 106.00 Mtr. 91.91
(h) One wire 25.00 sq. mm 44.00 Mtr. 236.34
(i) One wire 35.00 sq. mm 40.00 Mtr. 300.98
(k) One wire 70.00 sq. mm 8.00 Mtr. 669.63
(l) One wire 95.00 sq. mm 4.00 Mtr. 919.10
276 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv 680.00 Mtr. 22.22
grade ISI marked copper wires of following size to be erected as directed. (c)
1.00 Sq.mm 2 core round/ flat PVC sheathed
(e) 1.50 Sq.mm 3 core round PVC sheathed 584.00 Mtr. 46.46
277 Providing & erecting approved make following size of TV Co-axial flexible 350.00 Mtr. 62.62
cable comprising inner conductor of solid bare copper insulated with Foam PE
& Secondary conductor made of poly - Aluminium film bonded Al. Braids @
suitable coverage overall sheathed with black PVC insulation. (e) RG-11
278 Supplying & erecting approved make Telephone Cable electrolytic copper 2500.00 Mtr. 20.20
conductor PE insulation twisted in two pairs & wrapped with FRLS PVC tape
& sheathed with FRLS PVC or HFFR outer Jacket suitable for telephone
wiring & confirming to C-DOT erected in existing pipe of following size of
conductors & nos.of pairs with necessary connections. [A] Conductor Size
mm (a) Unarmoured (2) Two Pairs
(5) Ten Pairs 320.00 Mtr. 65.65
(6) Twenty Pairs 140.00 Mtr. 127.26
279 Supplying & erecting approved make LAN cable of following size in existing 2485.00 Mtr. 47.47
pipe as per direction [C] CAT -
280 Providing & erecting main Distribution (MDF) indoor type, back mounted 12.00 Ea 994.85
frame as per DoT standard approved with krone strips (a) Suitable for 10 pair.
(b) Suitable for 20 pair 2.00 Ea 1368.55
(c) Suitable for 50 pair 3.00 Ea 1747.30
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
281 Providing & erecting 6 core fibre optic SM 9/125um double sheath, CSTA, 300.00 Rmt 60.60
Unitube, Outdoor cable (per m)
282 Providing & erecting Switch board for Computer or electric apparatus 100.00 Ea 1133.22
consisting of following modular type accessories mounted with PVC / Metallic
concealed/open box with single mounting base frame covered with textured /
metallic / white front plate, modules erected with necessary connections as
1 no. 6A/16A universal plug-switch combined.
3 nos. 6A Switch
3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III
283 Bakelite adopter for Holder to be erected. 1089.00 Ea 9.09
284 Decorative call bell Ting-tong box type 250 volts complete erected 23.00 Ea 71.71
285 Providing & erecting insulated socket 3P+N+E with Plug 32A rating which is 4.00 Ea 2190.69
comprised of Four pole MCB slot and insulated socket IP40 cat-III
286 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 1089.00 Ea 373.70
0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall
be made of thick sheet steel conforming to IS: 513/CRCA/ aluminium die cast
powder coated and high U.V. & corrosion resistance with diffuser with
company mark/name 160V to 270V, Power Factor more than 0.95, THD <
15%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt, LED LED
driver efficiency > 85% (fitting required LM-79 & LM-80 Certificates) (NOTE:
Below description have shown ranges of Wattage capacity of LED fittings.
shown) (A) Tube Light with integral driver (iv) 22-24 Watts, Surge - 2KV, IP-
20, conventional 4 feet Cat-lll
287 Supplying and erecting led lamps with following wattage capacity of 220 to 264.00 Ea 188.87
240 voltage, minimum 15000 burning hours life, 500 V in built-surge
protection, Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp
holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser suitable
LAMP holder (iii) 10 to 15 watts Cat-lll
288 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 252.00 Ea 758.51
0.5 Watt assembled on single MCPCB, with housing used as a heat sink
shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium
pressure die cast powder coated and high U.V. & corrosion resistance with
diffuser housed in aluminium casted body with company mark/name 160V to
270V,Power Factor more than 0.95, THD < 15%, CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt, LED driver efficiency > 85% (fitting
required LM-79 & LM-80 Certificates) (NOTE: Below description have shown
any wattage capacity between the ranges shown) (A) Square/ Circular shaped
Surface/Recessed Mount Downlight with provision for spring loaded mounting
clips complete. IP20 (iv) 22-24 watts, Surge-2 KV Cat-lll
(B) LED Panel Light with provision for Plane front frame with translucent cover 6.00 Ea 724.17
fixed to housing complete. IP20 (v) 24 watts, 12" x 12", Surge-2 KV Cat-lll
289 Supplying and erecting LED street light / Flood light fittings with High power 11.00 Ea 3345.12
White LEDs wattage of 3 Watt and above assembled on single MCPCB,
efficiency more than 130 lm/w and corrosion free High pressure die cast
aluminum housing with smooth finish powder coated and heat sink extruded
aluminium with diffuser and Polycarbonate optics/ lenses, with toughened
glass with company mark/name engraved or embossed 160 to 270 V, Power
Factor more than 0.95, THD < 10%, CCT 3000 K to 5700K, Uniformity ratio
>0.45, Luminaire efficacy> 100 lumens/watt. LED driver efficiency > 85%.
(fittings required LM-79 & LM-80 certificates) (NOTE: Below description have
shown ranges of Wattage capacity of LED fittings. The Engineer incharge
(IP-65), Surge protection -4KV integral and Light must have 440VAC line
supply with over-voltage protection. (i) above 36 to 48 watts Cat-lll
(ii) above 48 to 60 Watts Cat-lll 95.00 Ea 4997.48
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot and 2.00 Ea 4819.72
spun aluminum canopy fixed with opal polycarbonate, pipe arrangement for
vertical mounting driver and accessories wired upto terminal block.IP 65 (ii)
32-40W Cat-lll
290 Providing and erecting Approved make Four pole moulded case circuit 28.00 Ea 6173.12
breaker having breaking capacity ICU of 25 KA. at 415 V,having normal
current rating up to 25 A to 100A. with Fixed thermal & magnetic release
suitable to work on A.C. supply 50 c/s. with all internal connections, spreader
tinned copper & complete erected in existing 16 G.M.S. housing. ICS=100%
of ICU only Cat III
291 Providing and erecting approved make Four pole moulded case circuit 20.00 Ea 8055.76
breaker having breaking capacity ICU of 35 KA. at 415 V. having normal
current rating 125A. with Fixed thermal & magnetic release suitable to work
on A.C.supply 50 c/s. with all internal connections, spreader tinned copper &
complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only Cat III
292 Providing and erecting approved make Four pole moulded case circuit 5.00 Ea 16221.61
breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal
current rating 200A.with variable Thermal & magnetic release suitable to work
on A.C.supply 50 c/s. with all internal connections, spreader tinned copper &
complete erected in existing 16 G.M.S.housing ICS=100% of ICU only Cat III
293 Providing and erecting Approved make Four pole moulded case circuit 6.00 Ea 20946.39
breaker having breaking capacity ICU of 35 KA. and above at 415 V having
normal current rating 250A. with variable thermal & magnetic release suitable
to work on A.C. supply 50 c/s. with all internal connections, spreader tinned
copper & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU
only Cat III
294 Providing and erecting Approved make Earth fault Relay suitable to mount 10.00 Ea 4687.41
with inter connection suitable to following size of moulded case circuit breaker
having CT ratio & MCCB rating as following along with shunt trip 220V AC.
with all internal connections & complete erected in existing M.S.housing. (1)
15 A -100 A, CT Ratio 1/100
(2) 125 A -200 A, CT Ratio 1/200 5.00 Ea 4983.34
(3) 250 A -400 A, CT Ratio 1/400 3.00 Ea 5415.62
295 Providing and erecting following additional parts for panel mounting MCCBs 59.00 Ea 873.65
(A) Extended operating rotary handle with pad lock with three position
trip,off,on suitable for 25A to 250 A panel mounting cat-III
296 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 6.30 Rn. 1961.42
Copper Busbars with four equal Nos. of electrolyte bus having current density Mtr.
not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly
wrapped with colour insulating tape for phase sequence of following current
carrying capacity, erected with necessary bus bar supports /insulators, main
cable socket to each bar, erected in existing cubical panel with necessary
connections.(A) Suitable for 100 Amp. Capacity
(B) Suitable for 200 Amp. capacity 2.40 Rn. 3202.71
(C) Suitable for 300 Amp. capacity 1.20 Rn. 4909.61
297 Providing and erecting Miniature circuit breaker single pole 0.5A to 2A system 105.00 Ea. 270.68
and having breaking capacity 10 KA to be erected in existing box. confirming
to IS 8828/1996 with ISI Mark Cat III
298 Providing and erecting Miniature circuit breaker single pole 6A to 25A suitable 920.00 Ea. 112.11
to operate on 240 V A.C. system and having breaking capacity 10 KA to be
erected in existing box confirming to IS 8828/1996 with ISI Mark Cat III
299 Providing & erecting 240 V MCB double pole switch for motor & inductive load 77.00 Ea. 330.27
(C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing
box having following capacity (B) 40 Amp. Cat III
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
300 Providing & erecting 240 V MCB double pole switch for lighting Load (B 57.00 Ea. 278.76
Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box
having following capacity (A) 6 to 32 Amp.Cat III
301 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) 11.00 Ea. 578.73
having 10KA breaking capacity & confirms to IS :8828 in existing box having
following capacity (A) 6 to 32 Amp.Cat III
(B) 40 Amp. Cat III 95.00 Ea. 638.32
302 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C 18.00 Ea. 668.62
Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box
having following capacity (b) 40 Amp.Cat III
(c) 63 Amp..Cat III 82.00 Ea. 737.30
303 Sheets steel powder coated enclosure suitable for incorporating One/Two 13.00 Ea. 176.75
304 Providing and erecting Sheet Steel powder coated MCB distribution board - 4.00 Ea. 1492.78
flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,
Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house
appropriate nos. of MCBs. (The DBs should be used of same company of
MCB to be used) suitable for (A) single phase incoming and horizontal single
phase outgoing (b) sheet steel double door (IP-43) (iii) 12 way
(v) 16 way 12.00 Ea. 1680.64
(B) three phase incoming and single phase horizontal type outgoing per 35.00 Ea. 2339.16
phase isolation type (PPI) (b) sheet steel double door (i) 4 way
(ii) 6 way 18.00 Ea. 2913.85
305 Providing and erecting Approved make RCCBs conforming to IS: 12640 and 3.00 Ea. 1969.50
having sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and
suitable for operation on single phase 240 V, 50Hz. having characteristic of
quick action & tripping with all advance feature & do not incorporate any
electronic component. for following Max. rating erected as directed (i)
Amps. DP Cat III
(ii) 40 Amps. DP Cat III 184.00 Ea. 2235.13
306 Providing and erecting metallic vitrified danger notice board as per language 21.00 Ea. 69.69
suggested by engineer incharge for MEDIUM VOLTAGE installation to be
erected as per IS-2551.
307 Providing & erecting Medium Voltage Danger Notice Board sticker as per 21.00 Ea. 26.26
language suggested by engineer incharge of standard size as per IS-2551
308 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 12.00 Kg. 794.87
309 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. 12.00 Ea. 368.65
dia. galvanised iron pipe with coupling and buch buried in specially prepared
earth pit complete with necessary 8 SWG earth wire.
310 For using salt and charcoal / coke as required for pipe type earthing. 12.00 Ea. 171.70
311 Supplying & erecting earth pit of minimum bore dia.150mm size approved 19.00 Ea. 4591.46
make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-
1987 made of corrosion free hot dipped G.I. Pipes having Outer pipe dia of
50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-
250 Micron galvanising, connection terminal dia of 12mm with constant ohmic
value surrounded by highly conductive compound with high charge dissipation
suitable for following type of applications with chamber and heavy duty cover.
(A) (approved make OEM has to submit test certificate including value of
earth resistance of installation duly stamped and signed by agency and officer
Incharge has to ensure the value of earthing resistane mentioned in test
Certificate) & having back filling compound of (B) Inner chemical (CCM
Compound) - Resistivity :- 0.2 ohm / meter testing as per IEC 62561-2017,
Voltage drop :- < 1 volt at no load & dry form, Sulphar content:- <2% (C) Back
fill Compound :- Earthing compound should be capable to retain moisture for
long time necessary test report must be submitted by Agency.
(a) For Electrical Installation up to 440V in normal soil
Length of pipe - 1 Mtr
Back filling compound - 1 Nos Bag of 15 Kg.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
312 Providing & erecting weather proof, dust & vermin proof, floor mounted front 19.10 Sq. 16323.62
operated outdoor type double door cubical panel board necessary IP-54 and Mtr.
above protection as per approval from engineer incharge made from 14 SWG
thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet
for internal partitions with necessary accesories, supporting angles/ flats
channel including cutting, bending, drilling, welding, riveting with internal
partitions & cable alley as per requirements & instruction of engineer-in-
charge with erection of supplied switch gears, BUSBARS, suitable size of
inter connecting PVC copper wire / copper-aluminium strips, rubber
grommets, rib, bakelite control fuses/MCB for measuring instruments, earth
bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of
hinged doors, handles with locking arrangement and rubber gasket,heavy
duty end terminal connection, danger notice board, necessary ventilation,
earthing strip complete.
The Panel shall be painted with epoxy powder coating. (The rates excludes
the cost of switchgears, bus bars, inter connecting mains & Copper
Aluminium strips, meters, fuses etc. The dimension shall be measured
excluding base beams) The panel shall be supplied with following approved
manufacturers with following size. (B) The standard companies switch gear
shall be used and only manufacturers at CPRI approved factory (i) with
350mm depth
313 Supplying & erecting XLPE(IS:7098) (I)-88 ISI unarmoured Aluminium cable 100.00 Mtr 71.71
1.1 KV.grade to be erected as directed of following size. (C) 2 core 6 Sq. mm
314 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand 203.00 Mtr 220.18
Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or
in existing trench / pipe of following size of cables (B) 3 1/2 core 35 Sq.mm
(16 Sq.mm 1/2 core)
(C) 3 1/2 core 50 Sq.mm ( 25 Sq.mm 1/2 core) 564.00 Mtr 284.82
(D) 3 1/2 core 70 Sq. mm (35 Sq.mm 1/2 core) 286.00 Mtr 378.75
(F) 3 1/2 core 120 Sq. mm (70 Sq. mm 1/2 core) 86.00 Mtr 540.35
(G) 3 1/2 core 150 Sq.mm (70 Sq.mm 1/2 core) 270.00 Mtr 731.24
315 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand / 803.00 Mtr 126.25
Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary
clamps or in existing trench / pipe of following size of cables (B) 4 core
(C) 4 core 10 Sq. mm 340.00 Mtr 140.39
316 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand 305.00 Mtr 190.89
Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or
in existing trench / pipe of following size of cables (B) 4 core 25 Sq.mm
317 Making trench in soft soil of suitable width of 90 cm deep for laying cable or 1170.00 Mtr 55.55
locating the fault all over the run and back filling the same and making the
surface as normal ground.
318 Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below 49.00 Mtr 226.24
ground across the road crossing or on floor with necessary material in an
approved manner and making the ground as per original. (F) 100 mm dia.
319 Providing & laying approved make Double walled corrugated pipes (DWC) of 1430.00 Mtr 62.62
polyethylene (conforming to IS 14930 II) with necessary connecting
accessories of same material at required depth in existing trench for laying of
cable below ground / road surface for enclosing cable (A) 50 mm outer dia.
(B) 63mm outer dia 370.00 Mtr 73.73
(C) 90 mm outer dia 389.00 Mtr 95.95
320 Providing and fixing heavy duty flange type brass cable gland with rubber ring 100.00 Ea 38.38
for PVC insulated armoured cable complete with out going tails, insulating
tape etc for following size of cables.(B) 2 to 4 core 6 Sq.mm
(C) 2 to 4 core 10 Sq. mm 40.00 Ea 38.38
321 Providing and fixing heavy duty flange type brass double compression type 6.00 Ea 66.66
cable gland with rubber ring for PVC insulated armoured cable complete with
out going tails, insulating tape etc for following size of cables.(A) 3 & 1/2 /
core 25 Sq. mm
(B) 3 & 1/2 core 35/50 Sq. mm 28.00 Ea 75.75
(C) 3 & 1/2 core 70 Sq. mm 6.00 Ea 103.02
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
(E) 3 & 1/2 core 120 Sq. mm 8.00 Ea 140.39
(F) 3 & 1/2 core 150 Sq. mm 8.00 Ea 190.89
322 Solder less crimping type Aluminium lugs conforming to IS suitable for cable 384.00 Ea 6.06
of following size evenly crimped with high pressure tool & connected to
switchgear terminals with brass / cadmium plated nut bolts in an approved
manner. (A) 1.5/ 2.5/4/6 Sq.mm
323 Providing & erecting Approved make Ceiling Fan with double ball bearing with 7.00 Ea 1982.63
Condenser 230 volt A.C.50 Hz. 900 mm sweep complete having 3 Aluminium
blades, canopy erected complete. [Make shall be approved by Engineer in
324 Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with 483.00 Ea 1948.29
double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm
sweep complete having 3 blades with aluminium blades with canopy & 30 cm.
down rod erected with earthing. (Make shall be approved by Engineer in
325 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe 490.00 Mtr 108.07
down rod erected duly painted for fan complete with proper insulation without
leakage and earthing.
326 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the 709.00 Ea 108.07
RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S.
box / Heavy Duty PVC box complete erected concealed in Ceiling with
necessary finishing.
327 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan 709.00 Ea 18.18
328 Supplying & erecting approved make low noise decorative exhaust fan having 106.00 Ea 1703.87
square frame ABS body with inbuilt lowers & square frame.200mm with
1350RPM Cat.II
329 Supplying & erecting single phase approved make industrial exhaust fan 40.00 Ea 2054.34
suitable for medium duty ring mounted low noise operation suitable for
medium duty having following dia size and maximum speed in RPM [A]
mm dia 900 RPM Cat.II
330 Supplying and erecting approved make Octagonal pole made from HR sheet 69.00 Ea 6874.06
steel. The pole should be made as per IS and shall be coated with hot dip
galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed
with integral Junction box consist of terminal plate of min 6mm Hylam sheet,
standard profile 35mm x 7.5mm Din-Rail for MCB Mounting, stud type
terminal and arrangement for cable termination to be erected with suitable
foundation (Included) as per details given by manufacturer considering site
requirement.(C) 5 Mtr. Long 70 mm top x 130 mm bottom dia, 3 mm thickness
with 200mm x 200mm x 12mm base plate, 4-M16 Bolts and 600mm long with
necessary G.I. J bolts. Approx Pole weight 46 kg
331 Supplying & erecting approved make SMC press moulded composite FRP 6.00 Ea 898.90
loop-in, loop-out approx. 2mm thick box complete with Bakelite connector strip
5way (3P+N+E), DIN rail for mounting mob & hinged doors as per
requirement having locking arrangements with mounting clamp with nuts,
bolts & washers suitable for erection on pole with cable clamps& earth bolt of
following size of box. (A) 300mm x 200mm x 100mm [deep]
(C) 150mm x 125mm x 100mm [deep] 2.00 Ea 476.72
332 Providing and erecting street light pole bracket comprising main B Class GI 45.00 Ea 614.08
pipe of 4.2 cm/require outside dia. complete with suitable B Class G.I sleeve
tubing of approx. 45cms.length and suitable for 76.5 mm / 80mm. / require
size pole top having sufficient fasteners for fixing the brackets and having
spread of 1 mtr. length with suitable rise as per site condition & suitable
welded stiffener reducer and nipple with check nut complete painted with one
coat of Red oxide / PU base primer and two coats of Aluminium / PU paint.
paint with following nos of arms.[A] Single Arm bracket 1 Mtr
[B] Double Arm Bracket 1 Mtr 26.00 Ea 829.21
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
333 Supplying and erecting B class Galvanized iron pipe having smooth finished 11.00 Mtr 215.13
bore of the pipe on both ends erected nuts and bolts along the pole / wall
shaping the pipe as per site requirement. Pipe dia as following.(B) 32 mm dia
334 Supplying & erecting IP 55 grade following size section pillar fabricated from 2.00 Ea 16691.26
joint less M.S. Sheet with angle iron legs made from jointless M.S. Angle with
cable clamps to be buried in ground to have appropriate erection to work
uniform until erected with cement concrete foundation and 45 cm high bricks
work finishing with plaster etc. hinged double door internally supported on
both side, with internal and outside looking arrangement with look and keys in
duplicate 35 x 35 x 5 mm M.S. Angle of Two Nos. one is welded and other
with nut and bolt for erecting Bakelite sheet. Painting the Section Pillar inside
and out side with three tank powder coated paint. section pillar roof should be
without joint with water leakage proof & tested as per IP 55 test & followed by
IS 2147 of 1962 (A) 150 x 90 x 75 cm section pillar fabricated from 14 Gauge
MS Sheet with angle iron legs 95 cm long made from 40 x 40 x 6 mm thick
335 Supplying and erecting HYLAM sheet on existing angle iron frame.for 2.00 Sq. 771.64
following thickness (B) 4mm Mtr.
336 Supplying & erecting approved make Digital time switch having lithium cell 6 5.00 Ea 3168.37
years operative and operate battery backup 1 channel day clock with
memory programme, suitable to operate on 240V + 5%, 16A with, floating
contacts Minimum switching setup time 1 minimum & LCD display. Also
comprised permanent ON/OFF switching. Programming switches & housed in
fire proof thermoplastic enclosure & transparent cover erected as required
with necessary connection erected as directed.
337 Supplying & erecting power contactor, AC3 duty for time switch complete 1.00 Ea 1883.65
erected as per direction Cat III (B) 2 pole 250V 32 Amp.
(D) 4 pole 440V 40 Amp. 4.00 Ea 2782.55
338 SITC of Digital / PCM / TDM EPABX System having SMT design, system with 3.00 Ea 77077.14
flexible universal slots. Inbuilt Auto attendant facility, Minimum 15 Nos.
conference, Analog extension line, Calling GSM, E&M line, PRI / EI & VOIP
program me through Analog telephone digital key from Ethernet, public
address cord, shall have unrestricted simultaneous dialing facility, QSIG
protocol on PRI, 95 / STD / ISD / Local-Locking, Class of Service, Quick Dial-
Single Digit dialing of any two external number, Once only ring device,
Chairman / Secretary - Do not disturb Facility, Power Down Mode, Hot Line,
Hot Outward Dialing, Day Night Mode, Auto Call Back, Barge-in, Call Pick Up
& Call Transfer, Call transfer while Ringing with Voice Guide System, (DISA),
Caller ID (CLI), CLI Base ECF, CLI Base routing Internet Ready Port, External
Music Port, Call Budgeting, Call Most Calculation (ASMDR), DID Direct
Inverse Dialing, External Music Input, Fax Homing, Global Directory Printing
with following capacities [[Approved by Competent Authority i.e. not Below the
rank of Executive Engineer] [C] No of Extension 48, No of Junctions 9, 8 Port IP
Resource in-built, 4 Port Web base Video Conferencing, No. of
expandable ports : 128, Operators Console - 01 Compatible : ISDN
339 Providing and erecting Digital key phone (12-16 direct key) [Approved by 3.00 Ea 3955.16
Competent Authority i.e. not Below the rank of Executive Engineer]
340 Supplying & erecting push button type telephone instrument having speaker 36.00 Ea 898.90
phone Caller ID & speaker phone with one touch memory (min.6 nos.) &
memories with display system Single line [Approved by Competent Authority
i.e. not Below the rank of Executive Engineer]
341 Supplying microphones stands with sturdy mechanism, treble free movement 1.00 Ea 445.41
& positioning of microphones, free from rust with superior quality of chrome
plating with following size. [Approved by Competent Authority i.e. not Below
the rank of Executive Engineer] (c) Fixed height 91 cms. & extendable up to
62 cms. with round base of dia. 23 cms.
342 Supplying & testing wireless microphone system for 92.5 MHz FM operation 2.00 Ea 1884.66
with effective range 200 feet with microphone having facility for frequency
adjustment & receiver with LED indicator Telescopic antenna with battery
cells. [Approved by Competent Authority i.e. not below the rank of Executive
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
343 SITC of Gooseneck microphone 1.00 Ea 12046.27
Unidirectional condenser microphone
Flexible stem
Phantom powered by amplifier
On/off sliding switch with priority contact
Supplied with fixed 2 m (78 in) cable and lockable DIN connector [Approved
by Competent Authority i.e. not Below the rank of Executive Engineer]
344 SITC of Dynamic microphone, 6.3mm jack Unidirectional dynamic 1.00 Ea 2887.59
microphone
Handheld or stand-mounted use with clip (supplied)
Rugged construction
Modern non-reflective dark Grey finish [Approved by Competent Authority i.e.
not Below the rank of Executive Engineer]
345 SITC of Music source, USB/SD/Tuner MP3 playback from SD card and USB 1.00 Ea 60294.98
FM tuner with RDS, presets and digital control
Simultaneous operation of SD/USB-player and FM tuner
Separate outputs for digital source and FM tuner [Approved by Competent
Authority i.e. not Below the rank of Executive Engineer]
346 SITC of PLENA 180W ALL-IN-ONE AMPLIFIER [Approved by Competent 2.00 Ea 29391.00
Authority i.e. not Below the rank of Executive Engineer]
347 SITC of PLENA 360W ALL-IN-ONE AMPLIFIER [Approved by Competent 2.00 Ea 67230.65
Authority i.e. not Below the rank of Executive Engineer]
348 SITC of Cabinet loudspeaker, 15W, black High-fidelity music and speech 15.00 Ea 9380.88
reproduction
Compact yet robust ABS enclosure
Supplied with adjustable mounting bracket
Complies with international installation and safety regulations [Approved by
Competent Authority i.e. not Below the rank of Executive Engineer]
349 SITC of Cabinet loudspeaker, 30W, black 7.00 Ea 13399.67
High-fidelity music and speech reproduction
Compact yet robust ABS enclosure
Supplied with adjustable mounting bracket
Complies with international installation and safety regulations [Approved by
Competent Authority i.e. not Below the rank of Executive Engineer]
350 SITC of Horn loudspeaker, 20W High efficiency drivers 10.00 Ea 9841.44
Wide opening angle
Excellent speech reproduction
Simple power setting
Water- and dust protected to IP
Versatile mounting bracket
Complies with international installation and safety regulations [Approved by
Competent Authority i.e. not Below the rank of Executive Engineer]
351 SITC of Horn loudspeaker, 30W High efficiency drivers 2.00 Ea 10306.04
Wide opening angle
Excellent speech reproduction
Simple power setting
Water- and dust protected to IP
Versatile mounting bracket
Complies with international installation and safety regulations [Approved by
Competent Authority i.e. not Below the rank of Executive Engineer]
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
352 SITC of 3LCD Lamp based projector having wxga (1280 x 800) or better 4.00 Ea 33895.60
resolution with minimum white brightness of 3800 lumens and color
brightness of 3800 lumens. The projector should have minimum 1HDMI,1VGA
input. Having contrast ratio of 15000:1 or more. the projector should have
auto vertical key stone correction of +/- 30 degree and Manual Horizontal of +/-
30 degree. the projector should have optical lens, throw ratio 1.30-1.56:1.
Zoom Factor of 1.2. Lens focus Manual having focal length 16.9mm to
20.28mm. projector should have features like AV mute slide, quick corner and
split function and should support wireless functionality with inbuilt wifi or wifi
dongle. [Approved by Competent Authority i.e. not Below the rank of
Executive Engineer]
353 SITC of universal Projector mounting kit, with necessary grouting, fasteners 4.00 Ea 6848.81
etc. with adjustable height and suitable for all types of projectors. [Approved
by Competent Authority i.e. not Below the rank of Executive Engineer]
354 SITC of 120 inch Self Lock MW (8 x 6) Instalock Slow Retraction Screen, 4.00 Ea 5334.82
Aspect Ratio-4:3 [Approved by Competent Authority i.e. not Below the rank of
Executive Engineer]
355 SITC of LIU 12 PORT Rack Mount - Loaded (LC) SM [Approved by 1.00 Ea 6901.33
Competent Authority i.e. not Below the rank of Executive Engineer]
356 SITC of PATCH CORD LC-LC SM DUPLEX LENGTH- 3m [Approved by 1.00 Ea 1901.83
Competent Authority i.e. not Below the rank of Executive Engineer]
357 SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded 5.00 Ea 4400.57
[Approved by Competent Authority i.e. not Below the rank of Executive
358 SITC of CAT6 UTP 24AWG PATCH CORD:1M,Plug 30U' Snag less 96.00 Ea 156.55
[Approved by Competent Authority i.e. not Below the rank of Executive
359 SITC of 24 x 10/100/1000BASE-T PoE ports 5.00 Ea 31996.80
4 x Gigabit RJ45/SFP Combo ports
Advanced L2 switching and security features
L2+ Static Routing
Optional “standard mode” or “surveillance mode” management user interface
193 W PoE budget [Approved by Competent Authority i.e. not Below the rank
of Executive Engineer]
360 Providing and erecting Inverter based approved make split air-conditioning 4.00 Ea 47879.05
unit consisting of condensing unit with variable speed fan motor, inverter type
hermetically sealed rotary compressor with accessories etc. duly connected
separately erected evaporating unit and blower motor with its accessories by
means of extra supplied proper insulated copper tubing,drain PVC pipes
suitable for (cost includes Eco Friendly green gas charging and 15A plug top
& Remote Control & MS Stand) with necessary core cutting. (2) For ISEER
Range (KWH/KWH) (4.0 to 4.49) (b) for 1.5 ton capacity
(C) for 1.7 to 2 ton capacity 6.00 Ea 63765.34
361 Supplying and erecting insulated pair of soft copper tubing open or concealed 50.00 Rmt 965.56
including power and control cable, necessary PVC drain pipes for Split AC
machine up to 4 TR capacity
362 Providing & erecting water cooler having storage capacity 150 Ltr. & cooling 16.00 Ea 55893.40
capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The outlet temp. of the
water should drop by 15˚C within a hour, The water cooler should be
comprising of hermetically sealed compressor, fan motor, condensing unit,
water tank surrounded by evaporating, coil, thermostats, relay etc.complete
with necessary inlet & outlet connection. The body of water cooler will be
made from Stainless Steel.
363 Supplying & erecting 5 stage single reverse osmosis water purification system 16.00 Ea 29187.99
with M.S. powder coated frame, prefilter housing with 'O' ring presediment
filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi,
mention with 40 psi inline type post carbon filter auto low & high pressure
switches with following size of storage tank & LPH capacity & erected as
directed [C] 50 Ltr / Hr with 150 psi 2 nos booster pump
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
364 Providing & Erecting Deep Freezers effective and economical Solutions for 4.00 Ea 41770.57
safe storage of perishable foods.The range of hard - top deep freezers
Technical Specification
Gross Capacity 400 ltr., Temp. Range -18°C to -22°C, Power Supply
230Volts, Single phase, 50 Hz, Refrigerant R134A, No of lids 2,Inner Cabinet
Pre-painted GP Steel, Puf Thickness 60*60,Over all No of Baskets
01,Wheels/Legs Heavy Duty Castors.
365 Supply and Erecting of Static Stabilizer suitable for following capacity of A.C 4.00 Ea 3030.00
Machine the Stabilizer Must have Minimum Technical Specification are Input
working Single Phase Voltage Range Up to 150V-280V.50Hz, Output Voltage
Range Up to 200V-240V, 50Hz, Autoreset Facility, LED Display for Indicating
Voltage, Spike / Surge Protection,Time Delay Facility, Proper Wall Mount
Facility with Required Accessries & on site 3 year replacement / repairing
(1) For 1.5Ton Thermal Overload Protection 12 Amp.
(2) For 2 Ton Thermal Overload Protection 15 Amp. 6.00 Ea 4029.90
366 Supplying and erecting approved make online Un-interruptible Power Supply 2.00 Ea 130103.15
system comprising flat cum-boost charger with IGBT base rectifier & Inverter
& sealed maintenance free SMF batteries. The charger having operating
capacity for input 160-270V AC & inverter having output 230V,50 Hz Ac with
0.8 load power factor with battery, over/under voltage output with over load &
short circuit protection equipment. The system housed in CRC sheet duly
powder coated paint with following power backup.with MS painted batteries
stand, 10% Overload capacity for momentary load.(D) 5 KVA with 1Hr Backup
367 Supplying, installing, testing & commissioning of SOLAR WATER heating 4.00 Ea 102530.15
system as per prevailing IS code comprising of Solar flat locket collector,
stainless steel hot water storage isolated tank with S.S. heat exchanger,
absorber made of copper sheet & copper tube of following capacity in liter /
day (LPD) with "B" size aluminium box collector with appropriate capacity
electrical backup arrangement (Excluding inlet & outlet pipe lines) (D)
Capacity of 500 LPD
(E) Capacity of 1000 LPD 6.00 Ea 189956.76
368 Supplying and erecting approved make panel mounting type Digital Voltmeter 11.00 Ea 1275.63
having 3 digits LED display, 0 to 750 AC Volts range erected on existing
panel board with all connection, wiring etc .with manufacturers calibration
certificate.
369 Supplying and erecting approved make panel mounting type Digital Ammeter 11.00 Ea 1558.43
having 3 digits LED display, external CT operated, calibrated for 0 to
Amps suitable to operate on 500 Volt AC, erected on existing panel board
with all connection, wiring etc. with manufacturers calibration certificate.
Supply 500 V on existing panel board with necessary connections.
371 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 33.00 Ea 274.72
ratio 15 VA burden erected in existing CRCA box duly secured with insulating
materials connected to the meter
372 Supplying and erecting approved make suitable panel indicator LED type 63.00 Ea 43.43
lamp, lens cover, complete erected with necessary connections.
373 Providing & erecting open well horizontal mono block pump set with cast iron 8.00 Ea 18746.61
body, complete for three phase submersible motor having [D] For 5 HP
phase open well horizontal mono block pump set suitable for 1350 LPM to
310 LPM @ 10 to 42 Mtr head suitable for 50/65 mm dia delivery pipe Cat.II
374 Supplying & erecting approved make motor control cubical panel (Direct - on - 8.00 Ea 7722.46
line) made from 16 G. CRCA sheet duly epoxy powder painted inside and
outside with hinged doors and locking, arrangement consisting of suitable size
of ON- OFF isolator (AC - 3/23duty) main fuses, single phasing preventer,
indicating lamps for R- Y - B phases, overload relay, Automatic water level
wires duly socket crimped, main contactor & overload relay, start - stop push
buttons, to be erected on angle iron frame grouted on wall as directed. The
isolator, overload relay & contactors will be of L & T, Siemens or BCH make
only. (A) DOL up to 5.0 H.P.
(B) DOL for 7.5 H.P. 2.00 Ea 8710.24
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
375 S.I.T.C. submersible pump set suitable for bore of 150 mm. dia. or more 2.00 Ea 35590.38
having three phase motor capacity not more than 7.5 H.P. with following
capacity. Lifting and Lowering taken extra.(A) (12 stage) 280 to 240 LPM
discharge at 90 to 104 mtrs. head respectively suitable for 50mm dia. delivery
pipe. Cat.III
376 Lowering of submersible motor pump set at the depth of following ,complete 2.00 Per 2568.43
with required. Nos. and size of casing pipes erected by means of proper chain Job
pulley block & pipe wrenches after checking of threads of each pipe with
coupling to take the load of the pump set and pipe assembly filled up with
water (B) Above 60 mtrs. and Up to 120 mtrs.
(D) For Open well Horizontal submersible pump set for sump well (i) 1 HP to 5 8.00 Per 856.48
377 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible 240.00 Mtr. 146.45
Submersible copper cable approved make of following size. (C) 3 Core x
(D) 3 Core x 6 Sq.mm. 280.00 Mtr. 172.71
378 Supplying of following size of STANDARD UPVC column pipe with coupler 220.00 Mtr. 297.95
and wire lock [D] 50 mm dia.
379 Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) 2.00 Per 1489.75
long, pump guard set, starter pipe Rubber ring for submersible pump & UPVC Set
column pipe as directed by Engineer - in - charge with necessary plumbing as
desired. [D] 50 mm dia.
380 Supply, Installation, Testing & Commissioning of following size of Grid Tied
Solar Power Plant with Solar Panels (ALMM approved): Frame Material :
Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High
Transmission Low-Iron Tempered Glass (AR Coated), High efficency and
positive power tolerance Pmax: 0/+5, Module Efficiency should be approx.
19.5%-22%, Normal operating temperature 45'C, Junction Box with
Waterproof IP67 & MC4 Compatible and Enclosed with Bypass diodes, 100%
Electroluminescence test to ensure error free Modules, Thep. temp. co-
efficient of the PV module shall equal or better than -0.45% degree C. Solar
PV modules of minimum fill factor 75% to be used. Unit Production:- More
than 4.5 Unit /kw /day (Actual) (1 Year Avg) with 10 year product warranty and
25 year Linear Power Warranty includes all mechanical and electrical
parameters of the Solar panel. Modules must be complied to the DCR
(Domestic content requirements).
The Ration of AC to DC is 5:6 for the Installation capacity which are given in
AC KW. Solar Inverter: MPPT Range: MPPT Range: 80-1000 V, Max
efficiency: 97.5% - 98.9%, O/p Frequency : 50/60Hz, Operating Altitude (m) ≤
4000, O/p Power Factor: ~1, O/P THDi: < 3%, Operating Tempreture Range: -
25~60°C, Integrated protection of Inverter are Anti-islanding Protection, Input
Reverse Polarity Protection, Insulation Resistor Detection, Ground fault
protection, Residual Current Monitoring Unit, Output Over Current Protection,
Output Short Circuit Protection, Output Over Voltage Protection, PV array
string fault Protection. Protection Degree: IP65, User Interface LCD & APP,
Datalogger & Communication: GPRS / Wi-Fi.
Module Mounting Structure : The mounting (Rectangular pipe / square pipe /
circular pipe) with requisite cross bars, nuts and bolts, etc. shall be Hot deep
galvanized with minimum 80 micron coating. The rectangular / square /
circular hollow pipe section used for the structure should have a minimum
thickness of 2.0 mm. other than above, the material thickness should be
minimum 2.5 mm. A certificate of a structural engineer certifying the strength
and stability of the mounting structure to with stand the weight and wind
speed of 150 km/hour throughout the life span of 25 years of the system, shall
be submitted by the vendors. Hot Dipped Galvanized steel coils suitable
arrangement for base plate for foundation, solar panel mounting, the structure
should be suitable for carry the load of solar panel,wiring, sprinkler system
etc. with necessary foundation work/wall mount, J bolt, anchor fastner etc. the
nut bolt used for installtion of stucture should be (SS 304) quality.
It. Rates in Total
Description of Item Qty. Unit
No. Figure Amount
The ground clearance of the bottom most edge of solar panel shall not be less
than 300 mm to 1200 mm or as per site’s technical / feasibility requirement.
a. Column –The minimum section (thickness) should be 60mm x 40mm
b. Rafter - The minimum section (thickness) should be 60mm x 40mm
c. Purlin - The minimum section (thickness) should be 40mm x 40mm Balance
of System with necessary Swichgears (Suitable size and protection of ACDB
& DCDB), inter connecting wiring, earthing system as per the CEIG drawing
approval, lightining arrester system as per the CEIG drawing approval, all
liasoning work with various Govt. department like state nodal agency,
DISCOM & CEIG is included in agency scope.
(Excluding All charges namely GEDA Application fees, Solar connectivity
charges, Meter connectivity charges, Meter testing charges and system
stability / strenthning charges)
(E) Grid Tied Solar Power System: 51 - 100 kW (3 - phase) 200.00 Per 40658.56
Total Rs.
i.e. Rs. Twenty Six Crore Fourty Six lacs Fifty Five thousand Nine hundred Eighty Three and Fifty Two paisa only.
I/We am/are willing to carry out the work @ ______________ % above/below percent (Should be written
in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.
Estimated amount put to tender Estimated amount put to tender
Deduct………% below Add………% Above
Net Rs. ___________________________ Total Rs. ________________________
In words ____________________ In words ____________________
1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-
Charge for which no extra payment shall be made.
2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.
3. GST and Income tax TDS will be deducted at a source while making payments of bills.
4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017
Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change
as per actual mix design the cost of difference of cement consumption have been deducted from the rate of original
item at the rate of input rate mentioned in all the tender.
5. The Contractor will have to submit the all required mix design at his own cost before execution as directed
and to be approved from the Engineer in charge.
Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and found order.
Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer
Lunawada (R & B) Sub Division, Mahisagar (R & B) Division, Mahisagar (R & B) Division,
Lunawada Lunawada Lunawada
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
E Tender Notice - Adarsh Nivashi Shala at Malvan.pdf
SBD Book - Adarsh Nivashi Shala at Malvan.pdf
BOQ - Adarsh Nivashi Shala at Malvan Ta. Kadana.pdf
Specification Index.pdf
Technical Specifications.pdf
Electrical - Adarsh Nivashi Shala at Malvan Ta. Kadana.pdf
Drawings.pdf
GRs.pdf
PQ - Adarsh Nivashi Shala at Malvan Ta. Kadana.pdf
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .