Special repair to Bldg P-96 (JCOs Mess) at 501 FSEG, Bldg No P-12/G incl fencing and external electrification work at Young Road, Sewage line near Bldg No P-105, P-106, P-107, P-108, P-109, and P-110 OTM or living of 1/3 GR at Birpur, Provn of Grani

Amount

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete unreinforced in ground floors and pavings n. exc. 15 cm thickness(below or above ground level) complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar (1:6) complete all as specified and directed (using old size bricks).

M&L for brick work (except bricks), straight or curved on plan exceeding 6 mtr mean radius and built in cement mortar 1:6 complete all as specified and directed. NOTE:- Old bricks retrived from demolition shall be reused.

Taking down cement or cement lime plaster on walls of any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work in CM 1:6 and finished surfaces even and smooth without using extra cement complete all as specified and directed by Engr-in-charge

M&L for rendering 15mm thick in cement mortar 1:4 on walls (fair / unfair finished faces of brick/concrete), finished even and smooth without using extra cement complete all as specified. (Water proofing compound where ever ordered shall be added and the same will be measured and paid separately)

M&L 10mm thick ceiling plaster in CM (1:4) on fair faces of concrete surfaces rendering is to be finished even & smooth without using extra cement complete all as specified.

M&L 18-20 mm thick machine cut kota stone slab flooring in step, floor etc over and including 15mm CM 1:6 screed bed laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing, rounding of edges & polishing complete including demolition of stone slab flooring.

M&L for machine cut Kota stone slab 18 to 20mm thick, as on vertical surfaces such as riser of steps, skirting, dado etc. over & including 10mm thick rendering (bedding layer) in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, rounding of edges and polishing complete including demolition of stone slab flooring.

M & L for 25 mm thick Cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in floor base complete all as specified and directed.

M&L for light shade vitrified tiles 10mm thick (square/rectangular) polished area of each tiles n.exc. 0.36 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for light shade vitrified tiles 10 mm thick polished area of each tiles nexc 0.36 sqm in skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including rendering 10 mm thick in cement mortar 1:4 finished rough to fix tiles complete all as specified and directed.

Demolition of stone slabs and tiles of any description and thickness as in floor, apron etc. laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for granite stone 15 to 18 mm thick glazed (table rubbed and polished) fixed as in plateform / floor and the like set in cement mortar 1:4 and pointed with white cement (1:2) using marble dust with admixture of pigment to match and exposed edges rounded/ half rounded with and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for granite stone 15 to 18mm thick glazed (table rubbed and polished) fixed as in vertical surfaces i.e. steps, risers, skirting etc. and the like set in cement mortar 1:4 and pointed with white cement (1:2) using marble dust with admixture of pigment to match shade of stone and exposed edges rounded with and including rendering 15 mm thick in cement mortar 1:4 on wall complete all as specified and directed.

M&L for grinding and polishing edges and rounding off granite, kota stone or marble slab etc to achieve smooth finish complete all as directed.

M&L non skid ceramic coloured tiles joint free tiles (400x400mm) x 7 to 8mm thick or (area of each tile exc. 0.11 Sqm but not exc. 0.18 Sqm) in floor set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L non skid ceramic coloured joint free tiles (400 x 400mm) x 7 to 8mm thick as in vertical surfaces in skirting/dado set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with & including rendering 10mm thick in cement mortar 1:4 finished rough to fix tiles complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350 x 250 x 6 to 7mm/ 450mm x 350 mm x 6-7 mm thick as on vertical surfaces such as skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:4 finished roung to fix tiles complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40mm graded stone aggreate), 75 mm thick as in plinth protection, finishing the surface even & fair without using extra cement the plinth protection shall be laid in alternate bays n exe 2 Sqm, 10mm joints shall be provided, joints shall be filled with bitumen mastic, bitumen mastic comprise of 1 Part of Hot bitumen 85/25 grade and 3 parts of sand all by weight complete all as specified & directed.

Supply only liquid water proofing compound Dr. Fixit / Fosroc complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm but n. exc. 4.00 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 sqm & n. exc 2 sqm each complete all as specified and directed

S&F for 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

M&L for 35 mm thick flush shutters, solid core construction, with block board core and plywood face, pannels, one face is covered with decorative face veneer with lipping/frame to match including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

M&L 35mm thick 2nd class hard wood factory made Glazed and skelton door shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified.

S&F pre laminated Solid PVC Door Frame of size 50mm x 47mm made out of 5mm one side prelam single piece extruded pvc profile, door profile are to be reinforced with 19x19mm MS square tube EDPM rubber gasket weather seal shall be provided through out the frame. The profile shall be mitred cut at two corners and joint by inserting 2 nos of 150mm long brackets of 15mmx15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed and fixing in opening as per specification & drawing.

S&F powder coated aluminium grill with mesh size 75 mm and aluminium bar 6 mm XPM type including all accessories such as channels for fixing grill screws etc. aluminium section 15 micron thick anodizing complete all as specified and directed.

S&F aluminium anodised windows with side hung shutter and frame made with aluminium section with and including glass (as specified below), Aluminium sections shall be of size as given below: - Frame: 47x44 mm x 1.08 mm thick , Top/ bottom and side style / rails of shutter -44 x 47 mm x 1.08 mm thick Glass: 5 mm thick tinted glass fixed with rubber gasket with aluminium beading. Aluminium fitting such as peg stay , aluminium hinges, aluminium handle 100 mm long, aluminium tower bolt 100 mm long and making good of wall surface with matching to existing surface complete all as specified and directed including taking out old aluminium window with grill.

S&F 150 mm long,aluminium,anodised, barrel tower bolts of extruded section ISI marked complete all as specified and directed.

S&F alluminium anodized handle, fabricated type, ISI marked complete all as specified of size150mm.

M&L mild steel butt hinges, medium weight 100 mm size (including welding to steel chowkhats) ISI marked.

S&F 100 mm size cadmium plated stainless steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

Supply and fix 300 mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F mild steel 300mm long, ordinary rat rail rod pattern spring including roller and roller plate (Helical door spring) for door shutter complete all as specified & directed.

S&F Steel ventilator fixed type with or without glazing bars, dovetailed or welded complete all as specified and directed.

S&F mild steel framed work for such as grills, grating etc with end of bars shouldered and/ or riveted forged into spikes, framed guard bars barred iron door, railings and similar work complete conforming to Fe-290 Gde E 165 complete all as specified & directed.

M&L for 4 mm thick plain sheet glass ordinary quality in windows exceeding 0.5 sqm in each pane with stainlesss steel complete all as specified and directed.

Supply and fix 4 mm thick frosted sheet glass, ordinary quality in aluminium windows exceeding 0.5 sqm in each pane with stainles steel screws complete all as specified and as directed by Engr-in-Charge.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as directed by Engineer- in -Charge.

S&F in repair 20 mm dia stainless steel polished 204 grade drapery rod 1mm thick , decorative, including brackets, decorative finials at both ends complete all as specified and directed.

M&L applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer including preparation of new steel or iron surfaces of any description exc 10 cm width or girth, complete all as specified and directed.

M&L for preparation of new or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for 2-3mm thick wall care putty on wall surfaces finished even and smooth complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying wall putty 2 to 3mm on walls to make the surface smooth and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for preparation plastered surface of ceiling and applying two coats of white wash on ceiling , complete all as directed by Engr-in-Charge

M&L for complete removal of existing treatment of ceiling and applying three coats of white wash on ceiling including preparation of surface complete all as specified and directed.

M&L for newly plastered surface of walls including corners and applying two coats of 100% Premium exterior acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over applying of 1-2 mm thick wall care putty finish wall surface even & smooth complete all as specified and directed.

M&L for complete removal of existing treatment of walls including corners and applying two coats of 100% Premium exterior acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over applying of 1-2 mm thick wall care putty finish wall surface even & smooth all as specified and directed.

Dismantling of walls/ceiling boards (fibre, pulp, insulation, etc) or insulation boards/ slabs / blankets, any thickness including cover fillets etc, complete all as specified and directed.

Providing & fixing false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, all complete at all heights as per direction of Engineer-in-Charge.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-410-W (Gde-E-250) quality A complete all as specified and directed.

Taking up or down steel tubing with connections and removed from site of size 15 mm bore GI tubing.

Taking up or down steel tubing with connections and removed from site of size 20 mm bore GI tubing.

M&L cutting chases, pinning in, making good to facing where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth in Brick/ RCC complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Fixing only 15 mm bore steel water tubing galvanised 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. laid in trenches complete all as specified and directed:- (Note:- Excavation and earth work shall be measured and paid separately under respective item of schedule 'A')

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Fixing only 20 mm bore steel water tubing galvanised 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. laid in trenches complete all as specified and directed:- (Note:- Excavation and earth work shall be measured and paid separately under respective item of schedule 'A')

S&F in repair vitreous china wash hand basin with brackets, white, size 550 x 400 mm including CP brass 32mm waste fitting with long screwed shank and fly-nut, 32 mm PVC waste pipe including cutting for and pinning in ends of brackets complete all as specified.,

S&F pillar tap 15 mm dia cast copper alloy, chromium plated, swan neck, with left/right hard operating knob, Make:- Jaquar model No. 5357N or equivalent in Cera or parryware.

S&F in repairs vitreous china water closet Padestal pattern (white) with 'P' or 'S' trap including flush pipe, seat cover with chromium plated hinge divice, fixing in floor with brass screws and necessary connection complete all as specified.

S&F in repaies vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest fixed with cement joint and providing lime concrete bedding and connecting to flusing cistern including 'P' or 'S' trap of CI complete all as specified and directed.

Supply only plastic water closet sheet covers white closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Dismantling and taking down existing flushing cistern of any capacity and type from its position and removing from site complete all as specified and as directed by Engr-in-Charge.

S&F 32 mm dia waste fittings, brass chromium plated suitable for sink, WHB, etc with long screwed shanks and flynuts, flange embedded in cement complete all as specified and directed.

S&F 32 mm bore PTMT waste pipe suitable for wash hand basin/ sink etc not less than 610mm in length complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts, of 450 mm length complete all as specified and directed..

S & F 15 mm bore bib taps, chromium plated cast copper alloy long body, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F Health Faucet with 1 mtr metalic expandable tube & hook complete all as specified and directed. Make : Jaguar model No. ALDCHR 565 or equivalent in parryware / hindware.

S&F CP Jet spray for (L- Band) with 1.0 m long cp tube and hook with fitting complete all as specified.

S&F PTMT Grating 150 mm square size with or without hole complete all as specified and directed.

S&F in repairs 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified.

S&F in repair 75 mm dia PVC (SWR) multi floor trap, with CP grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/ wall with PVC clamp and holder bats complete all as specified.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches/ wall with PVC clamp and holder bats complete all as specified.

S & F PVC (SWR) bends, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 110 mm dia pipe complete all as specified and directed.

S & F PVC (SWR) bends, reducer any radius with rubber ring joints, fixed to wall / floor / in trenches complete all as specified and directed for 75 mm dia pipe complete all as specified and directed.

S&F in repair Angle cock, brass chromium plated, fancy type, with wall cap with round headed knob, suitable for 15mm bore iron pipe (2 in 1) complete all as specified. Make:- Jaquar cat No FON-40053/ Hindware cat No F 160017/ Prayag Cat No 9410.

Dismantling plain or corrugated steel shetting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section in any position in unframed work complete all as specified and directed.

M&L Pre-painted galvanlume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strangth of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F structural steel work as in roof trusses (framed), trussed, purlins crane gantries, rails & fastenings & heavy brackets framimg (Beam, tee, angle, channel or flat section) including distance pieces, cleats etc. Structural steel conforming to Fe-410W, Grade-E 250, Quality 'A' .

S&F fibre glass reinforced translucent corrugated sheeting 2 mm thick with two corrugations side lap with coach screw and washer in roof, wall etc complete all as specified and directed.

Dismantling fencing wire mesh, any type and removing from site complete all as specified and directed.

Supply only MS chain link fencing 3mm dia, GI plain wire, 50x50mm mesh or type weight n.exc 4 kg per square meter complete all as specified and directed.

Fixing only chain link fencing, including line wire any mesh, size & type to any type of standard rail, straining bolt etc, including provision of binding wire.

S&F MS round bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for securing wiremesh etc in fencing including drilling holes complete all as specified and directed.

S&F mild steel screw bolts 11 to 15 mm dia (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 5 cm but n exc 10 cm long.

M&L for cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar (1:3) or PCC 1:2:4 type B-1, depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exc. half brick but not exc. one brick complete all as specified and directed.

S&F mild steel work as in bends, scraps, hold fasts and similar articles conforming to Fe- 290 gde E-165 complete all as specified and directed.

S&F 35mm thick 2nd class hard wood factory made, plain framed panelled shutters (two or more pannels) with lock rail and panels of 9mm thick BWP commercial ply kiln seasoned and chemically pressure treated complete all as specified and directed.The size of rails and stiles as per IS-1003(Pt I).

S&F Factory made solid panel PVC door shutter 30 mm thick (style) both side prelam consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of both side prelam plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.complete all as specified.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or weldedcomplete all as specified & directed.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified & directed.

M&L for Ist class hardwood beads, straight (nexc 9 sqcm in section) for fixing galvanised MS wire cloth, renewed, including mitres etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S&F alluminium anodized barrel tower bolt extruded section 200mm length of bolt, ISI marked complete all as specified.

S&F alluminium anodized barrel tower bolt extruded section 100mm length of bolt, ISI marked complete all as specified.

S&F 250 mm long MS sliding door bolts ISI marked bolt type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed all as specified and directed.

S&F extruded aluminium alloy handles, cast type, anodised 100 mm size complete all as specified and directed.

M&L for coloured joint free non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06sqm but not exceeding 0.11 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed 15mm thick in CM 1:6 complete all as specified and directed .

S&F 15mm dia stop valve cast copper alloy , screwed down high pressure with cluch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F in repair CP brass shower rose , 100mm size suitable for 15mm dia pipe complete all as specified and directed.

S&F 08 ltr dual capacity PVC low level flushing cistern including PVC syphon and float vlave with PVC long bend for out let, fixing with WC complete all as specified and directed by Engr-in-Charge.

Dismantling water tank capacity exc. 250 ltr but n.exc. 500 ltr capacity complete all as specified in SSR Part I and as directed

S&F rotational moulded polyethylene 500 Ltrs Capacity water storage tanks three layered, (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball valve PTMT, with polythelene float and fly nut including 20mm dia GI medium grade over flow pipe , approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.

S&F in repairs Sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding un cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495x420x178mm bowl size 410x330x160mm complete all as specified.

S&F PVC (SWR) junction single, (Single T) equal or unequland, 110mm bore with access door complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or unequland, 75mm bore with access door complete all as specified and directed.

S & F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed.

S & F 75 mm dia PVC (SWR) vent cowl complete all as specified and directed.

M&L for applying three coats of white wash on walls including preparation of newly plastered surface or un-plastered surface complete all as specified and directed.

M&L preparing surfaces plastered or un-plastered old surfaces of walls and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for preparing plastered or un-plastered old surfaces of walls and applying one coat of white wash on wall complete all as specified and directed.

M&L for newly plastered surfaces of wall including corners and applying two coats of distemper oil emulsion over applying of 1-2 mm thick wall care putty over a primer coat complete all as specified and directed.

M&L for preparation of old plastered/unplastered surfaces of walls including by brooming down or steel wire brushing, scraping down, smoke soot, moulds, moss, afforescent salt and treading oil greasy spot. and finally clean with sand paper and applying two coat of cement base paint on external wall surfaces all as specified and directed.

M&L for complete removal of existing treatment from wall upto plaster surface by electric sand paper grinder, washing, rubbing down, and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oill, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper and applying two coat of cement base paint on external wall surfaces complete all as specified and directed.

M&L for 75mm thick cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of floor for laying floor finish complete all as specified and directed.

M & L factory made prepolished rubber moulded chequred cement concrete tile 30 cm x 30 cm x 20 to 22 mm thick with 3 mm spacer bar, set, jointed and pointed in neat cement slurry as in floor with grey cement and filling joints with colour pigment over and including 20 mm thick screed bed in cement mortar 1:6 including dismantling of old tiles complete.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep in soft/loose of soil for foundation, etc. or for shafts, wells, cesspits, manholes, pierholes, cable etc. and getting out complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete as in sub base floor complete all as specified and directed.

S&F mild steel TMT bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia as specified .

M&L for precast PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in coping, benching etc including necessary weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Returning, filling in soil including spreading, leveling watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed

M&L for 65 mm thick vibromatic reinforced precast cement concrete 1:1:2 (using 20mm graded stone aggregate) with 2mm thick mild steel CR sheet around painted with 2 coats of bituminous paint , as in man hole cover slabs finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work, 100 mm long handle of 12mm dia round bar counter sunk by 25mm welded to reinforcement complete all as specified and directed by Engr-in-charge (Note : CA No and date will be engraved on covers. Reinforcement shall be measured and paid saperately. Curing will carried out with ponding method)

S&F mild steel TMT bar 06 to 08 mm dia, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia as specified .

S&F Joist channel, angle or tee sections fixed independently without connecting plate etc. (cut to ordinory length i.e. within 20 mm of the length indicated) conforming to Fe-410-W (Gde- E- 250) quality B complete all as specified and directed.

M&L for concrete bed in PCC 1:3:6 type C-2 ( using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

M&L for Reinforced concrete pipes, class NP3 150 mm bore, laid & jointed in cement mortar complete with collars complete all as specified & directed.

Sucking out sewage water through sewage tanker from the man hole/septic tank/soakage well in different location and disposing off out of MD land as directed by Engr-in-Charge. Notes. For cleaning of sewage system:- (a) Contractor's representative shall attend office of Engr-in-Charge on all working days at 0900 hrs to collect the complaints pertaining to blockage of traps, cleaning of sewage lines, manholes, septic tank and soak wells . In case contractor's representative fails to report Rs 450/- per day will be deducted from the contractor payment for the absent period. (b) complaint slips shall be deposited to the JE concerned after completion of job duly singed by the users. payment shall be made on the basis of complaint slips and site verification by JE/ Engr-in-Charge. (c) Contractor shall provide printed complaint register/ slip as per format given by Engr-in-Charge before commencement of work. (d) The work in foul conditions such as cleaning of soakwell, septic tanks, manholes etc shall be carried out with mechanical means where work with mechanical means is not practicable and work shall be executed manually with the permission of Engr-in-Charge.

Provn of 50 users septic tanks including excavation and earthwork in any type of soil , PCC foundation, brick work, RCC cover slab, precast RCC man hole cover with angle iron frame vent shaft and sludge chambers complete all as shown on TD drawing, specified and directed.

M&L for construction of soakage well, internal dia 2.4M dia & depth 3.0M including excavation and earthwork in any type of soil ,brick work etc,complete all as shown on TD drawing, specified and directed.

M&L for marble stone (makrana white) 30 cm x 30 cm 15 to 18mm thick (table rubbed and polished) fixed as in floor, pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of slab including grinding, rubbing and polishing to mirror finish and exposed edges rounded with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 complete all as specified and directed.

M&L for prepolished makrana white marble of size 30cm x 30cm x 15-18 mm machine cut bedded jointed and pointed with grey cement slurry as in skirting/ dado including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for grinding and polishing to achieve mirror finish on existing terrazzo/ stone flooring, dado, skirting etc. by machine or by hand with 120 to 150 grit size earbutandom stone cleaning and washing the surfaces rubbed hard with felt and slightly moistened exilic acid powder @ 5 Gram per sqm complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.50 cum, getting out , returning, filling in & ramming earth or borken rubble mixed with earth around, in layers not exceeding 25 cm, watering & removing surplus soil to a distance n exc 50 m & making good surface.

M & L for plain cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed.

S & F steel work in tubular truss, poles including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 quality-A all as specified and directed

M&L for vitrified ceramic tiles (double charge) of 10 mm thick (square or rectangular) polished area of each tiles not exceeding 0.36 sqm in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 floor finished complete all as specified and directed.

M&L for vitrified ceramic tiles (double charge) of 10 mm thick (square or rectangular) polished area of each tiles not exceeding 0.36 sqm in verticle surface, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 10 mm thick in cement mortar 1:4 complete all as specified and directed.

S&F toilet paper holder box type, CP fixed to wall with chromium plated brass screws and rawl plugs complete all as specified and directed.

S&F Brass chromium plated wall mixer (3 in 1) complete all as specified and directed. Make: Jaguar Model No CON 281KN, HSH 1929 & OHS 1989/ Marc ES547A & ES 531 (Telephone shower)/Pearl ARI 016, HS 470 SHP 525, SHA 512.

S&F 15 mm dia brass chromium plated bib taps, short body, wall flange, fancy type, with round headed knob screwed down to GI pipes or for brass ferule or to GI socket complete all as specified and directed.

S&F Angle valve 15mm dia cast copper alloy chromium plated with wall flange suitable for 15mm dia GI pipe.

S&F 2 way Angle valve 15mm dia cast copper alloy chromium plated with wall flange suitable for 15mm dia GI pipe.

S & F soap dish, brass, 100x100x60mm chromium plated,fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed.

S&F corner Shelves of PTMT in set of three 300 mm size fixed with and including chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and directed.

S&F CP steel grating 100 mm dia with steel frame and hinge with or without hole complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safecustody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified.

M & L for point wiring complete with PVC insulated and unsheathed, Flame retardant low smoke ( FRLS ) 1100 volt grade electric cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core in and including rigid PVC surface conduit not less than 19 mm dia, clip, complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including MS Box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly complete all as specified including lugs required for One light/fan point controlled by one switch , complete all as specified and directed.

One light point point controlled by one-one way switch.

One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board.

All as per Item No 157 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete all as specified and directed.

S&F switch piano flush type single pole, 5 Amps, one way all as per specified & directed.

S&F switch piano flush type single pole, 16 Amps, one way all as per specified & directed.

S&F socket outlet 6 Amps, 5 pin, 2 in 1 complete all as specified and directed.

S&F socket outlet multipurpose 5 and 15 Amps, 5 pin, 2 in 1 complete all as specified & directed.

S&F ceiling rose surface bakelite 3 terminals of size 65x25mm. complete all as specified & directed.

S&F in replacement surface/Pendent mounting 1x20/22 W LED tube light fitting's Epoxy powder coated white extruded aluminium channel housing, Milky white, special polycarbonate diffuser, white coloured ABS end caps, better lumens and longer lamp life, high efficiency and lower power consumption, extra ordinary long life LED's, with & including 1 Nos 20/22 watt LED tube, complete and connected to ceiling rose with required length of two core flexible copper conductor cable (23/0.0076), fixed on walls/ceiling complete all as specified and directed.

S&F in replacement LED light fitting 1x10 watt bulk head LED type luminaries and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified & directed.

Supply and fix in replacement LED Mirror Light, 2 feet, 10 Watt, 230V, surface mounted decorative mirror optic type with engineered plastic body and including tube rod and connected accessories including provision of flexible copper wire from ceiling rose to light fitting terminal complete all as specified and directed.

Supply & fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc

S&F in replacement metal clad single pole and neutral enclosure with 2 pin and earth plug and socket complete with and including one single pole MCB 20 Amp 240Volt complete.

S&F in replacement sheet metal enclosures 240 volt 8 way with suitable rated bus bar for Single door IP-43DB's complete all as specified and directed .

S&F MCB single pole 240 volt 10 KA 5 to 40 Amp, conforming to relevant IS complete all as specified & directed.

S&F MCB SPN 240 Volt 10 KA 40 Amp conforming to IS complete all as specified.

M&L in replacement sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with Two runs of 4 Sqmm as current carrying conductor and one run of 4 Sqmm as earth conductor PVC insulated FRLS cable with multi stranded copper conductor of nominal cross section area as under and drawing into and including concealed PVC non metallic rigid conduit medium grade complete all as specified. Note:- Two runs of wire and one run of earth wire shall be measured as one meter only for payment purpose.

Taking down carefully exhaust/Ceiling fans, dismantling blades and removing exhaust fan and blades to strore,for painting of exhaust fans with synthetic enamel paint by one coat of spray painting with (matching to existing color) and with glossy finish including preparation of surfaces by removing old paint, proper cleaning , filling cavities with filler, and writing fan No./MES No. etc with black paint etc and rehanging in original position and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

M&L for rewinding of Ceiling Fan by removing old/burnt/UNSV winding, ball bearing , brass bush and replaced with new winding, ball bearing of existing size, brass bush and after repair, apply painting with synthetic enamel paint by one coat of spray painting with (white) and with glossy finish including preparation of surfaces by removing old paint, proper cleaning , filling cavities with filler, complete all as specified and directed.

M&L for rewinding Exhaust Fan by removing old/burnt/UNSV winding, ball bearing , brass bush and replaced with new winding, ball bearing of existing size, brass bush and after repair, apply painting with synthetic enamel paint by one coat of spray painting with (white) and with glossy finish including preparation of surfaces by removing old paint, proper cleaning , filling cavities with filler, complete all as specified and directed.

M&L for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 m below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 20 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch all as shown in electrical plate No 3 of SSR Part-I 2009 including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded stone aggregate), 50mm thick precast RCC (1:2:4) type B-1 using 20mm graded stone aggregate cover slab (reinforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia), with 40x40x6mm MS angle iron frame including necessary earth work and testing on completion, complete all as specified and as directed.

Supplying fixing jointing testing in replacement LT under armoured electric power cable 10 sqmm 4 core XLPE insulated, Screned PVC bedded galavanised steel strip or wire armoured conforming to IS 7098 (Part-I) 1985 ISI marked with aluminium multi stranded heavy duty 1100V laid in trenches / under floor, roads path or fixed on walls / on poles in heavy duty etc. as specified and directed of following size including lugs / thimbles / Glands including connecting testing & commissioning all bare conductor duly insulated 1.1 kv grade heat shrinkable sleeve at both ends complete all as directed by E-in-Charge.

Supplying fixing jointing testing in replacement LT under armoured electric power cable 35 sqmm 3.5 core XLPE insulated, Screned PVC bedded galavanised steel strip or wire armoured conforming to IS 7098 (Part-I) 1985 ISI marked with aluminium multi stranded heavy duty 1100V laid in trenches / under floor, roads path or fixed on walls / on poles in heavy duty etc. as specified and directed of following size including lugs / thimbles / Glands including connecting testing & commissioning all bare conductor duly insulated 1.1 kv grade heat shrinkable sleeve at both ends complete all as directed by E-in-Charge.

M&L for sand cushioning and covering of UG cable using crushed metal sand in trenches for cable protection complete all as specified and directed.

M&L for brick well burnt Class ‘B’ as cover to U/G cable laid dry flat over the cable with width equal to length of the cable and abutting each other with gap between adjacent slab not exceeding 10mm over under ground cable for cable protection in trenches all as specified and directed by Engineer-in-Charge.

Cutting existing road/hardstand of any type by using crow bar chisel uprto a depth of 30 cm for laying GI pipe including making good the surface by returning filling watering ramming in layers 150 mm thick PCC 1:2:4 over 200 mm thick hard core of broken bricks/stones over returning filling watering ramming in layers not exceeding 25 cm thick complete all as specified and directed by Engineer-in-Charge.

M&L for GI tubing medium grade (ISI marked) with all fitting/acessories for protection of cable on pole/wall and under road crossing including clamps, nut bolt etc all as specified and directed of size 40mm dia complete all as specified and directed.

Supply, transporting, erection and fixing steel tubular pole, 9 metres long, type 410 SP-31, complete with MS base plate 6 mm thick, plug at top cap, finial taper plug, bolts, nuts, washers etc including painting two coats of aluminium paint over one coat of red oxide primer including 3 nos band/straps with red post office box colour (300mm wide each) synthetic enamelled paint at a distance 300mm from plinth block and marking pole nos with black synthetic enamelled paint including tarring one coat on steel surface embedded in concrete complete all as specified and directed. NOTE:- Excavation, Earthwork and PCC work shall be measured and paid seperately

Supply and Fixing street light bracket made out of 40 mm dia GI pipe light grade bend to shape welding etc and fixing on wall with 40x6 mm flat iron MS clamps including necessary nuts, bolts and washers etc complete all as specified and as directed.

S&F junction box made of glass fibre reinforced and transparent poly carbonate of size 126x228x111, KV PC 8104 with IP 65 protection including MCB SP, 6 Amps 1 No and suitable size clamps fixing for pole/in pcc foundation etc,including taking down the old one,all as specified and as directed.

Supply and fixing LED flood light 100 watt 230 Volt AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp complete all as specified and directed.

S&F Step type,electronic fan regulator, 120 watt, 240 volts socket type fixed on the phenolic laminated sheet complete all as specified & directed.

S&F in replacment sheet metal enclosures 415 volt TPN 4 way with suitable rated bus bar, double door IP-43 DB's With MCB 4 pole 415 Volt, adjustable type 63 Amp complete all as specified and directed by Engr-in-charge

S&F in replacment sheet metal enclosures SPN 240 volt with suitable rated bus bar for double door 12 way IP-43 DB's suitable for one MCB SPN as incoming and 10 MCB SP as out going, mounting flush on wall/concealed complete all as specified and directed by Engr-in-charge.

S&F lamp holder polycarbonate insulated body with back plate with complete all as specified.

S&F in replacement surface mounted LED downlighter 12 W with durable housing with aluminium heat sink with diffuser with removal driver complete making good disturbed surfaces of wall to match existing colour all as specified and directed by Engr-in-charge.

Taking down existing ceiling fan any sweep and re-hanging ceiling fan including painting of ceiling fans complete in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc complete all as specified & directed.

Taking down existing exhaust fan any sweep and re-fix exhaust fan including painting of exhaust fans complete in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc complete all as specified & directed.

M&L in replacement sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with Two runs of 6 Sqmm as current carrying conductor and one run of 6 Sqmm as earth conductor PVC insulated FRLS cable with multi stranded copper conductor of nominal cross section area as under and drawing into and including concealed PVC non metallic rigid conduit medium grade complete all as specified. Note:- Two runs of wire and one run of earth wire shall be measured as one meter only for payment purpose.

Supply and fixing in replacement single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240 volts

VERDHMAN ASSOCIATES

M/s Anil Kumar

PAWAN KUMAR

M/S C S AITHANI

M/s Pradeep Kumar

M/S JAI PRAKASH GOEL

SARASWATI CONSTRUCTION CO