Construction of 50mtr Span Bridge over Naked Khad at RD 0/285 on Kuru to Ghallour road km-0/000 to 2/550

Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drain and Parapets etcetra in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiseling /wedging out rocks (Where blasting is prohibited) as per drawings and M.O.R.D. technical specification section 300 and 1600 and as per direction of the Engineer- In – Charge including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto any lead and lift including dressing of sides, bottom and back filling in trenches with excavated suitable approved material to the original surface in layer not executing 150 mm (one hundred fifty millimetre) compacted thickness including shoring and strutting and pumping and bailing out water (surface and sub soil water ) upto any depth any quantam of water including cleaning of slush which may arise out during dewatering complete as per direction of Engineer-in-Charge. Including carriage of materials within all leads, lifts and other incidentals. The rates is including Royality, Malkana, Octroi, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete Grade M-10 (M-Ten) nominal mix 1:3:6 (One cement isto three sand isto six graded crushed stone aggregate 20mm (Twenty millimeter) nominal size), in or under open foundation for all type of structures and in drains, pipe culverts and the like etcetera complete including pumping or bailing out water, dewatering (surface/sub soil water)including removal of slush which may arise at time of laying under water for all heights/depths and any quantum of water, including cost of form work and curing complete for 14 (fourteen) days and as per drawing and MORD Technical specification section 800, 900 & 1200 and as per entire satisfaction and directions of Engineer-in-charge, including carriage of materials within all leads, lifts and other incidentals. The rates is including Royality, Malkana, Octroi, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN (eighty to one hundred kilonewton) weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 and 400.12 and M.O.R.D.Technical Specification Section 400 and as per direction of Engineer-in-charger including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rates is including Royality, Malkana, Octroi, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and laying factory made 80mm thick chamfered edge Cement Concerete Paver Block of NTC/ PRIME Crete / NITCO/GICO make in footpath parks lawns, drive ways or light traffic parking etc, of required strength M-40 thickness & size & shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick required compacted bed of coarse sand, compacting and proper embedding/laying of inter locking paver blocks into the fine sand bedding layer roughvibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in all leads lifts and technical specifications as per the direction by the Engineer-in-Charge and other incidentals. The rates are inclusive of octroi, royality, Malkana, toll tax, sale tax or other taxes imposed by the Government, but including GST.

Providing and laying mechanically mixed and vibrated plain cement concrete in all type of structure as per drawing and MORD technical specification section 800, 900 ,1200 and 1600 for nominal mix 1: 4: 8 (one cement isto four sand isto eight graded crushed/broken stone aggregate 40mm (forty millimetre) nominal size and curing complete including pumping or bailing out water, dewatering, removal of slush as required at site which may arise at the time of laying concrete complete for all heights/depths including the cost of form work in retaining walls, breast walls and in pavements etcetera as per the direction of Engineer-in-Charge including carriage of materials, within all leads, lifts and other incidentals. The rates is including Royality, Malkana, Octroi, toll tax, sale tax, GST or any other taxes imposed by the Government.

Construction of un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M-25 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, admixtures as approved, curing of concrete slabs for 14 days using curing compound ( where specified) and water finishing lines and grade as per drawing and Technical Specification clause 1501

Providing and Laying of cold applied thermoplastic compound road marking paint 2.5mm (two decimal five millimetre) thick with refletorising glass beads at the rate 250 gram (two hundred fifty) gram per square metre area, thickness of 2.5mm (two decimal five millimetre) is exclusive of surface applied glass beads as per specificaiton and with strips of 0.10 (Zero decimal one) metre width in centre lines or edge lines of the road as per the directions of Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and Fixing 1200x900mm (One thousand two hundred into Nine Hundred) size Direction and place identification retro-reflective sign board as per IRC made of1.5mm (one decimal five millimetre) thick sheeting and supported on 40mm (fourty millimetre) dia Pipe painted with red lead primer as per approved drawing and technical specification clause clause vide clause 1701.2.3 and and as per direction of Engineer-in- Charge including carriage of materials and equipment with all mode of transportation and as per direction of Engineer- in- Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board 600 mm (six hundred millmetre) circular board as per IRC:67 made of 1.5 mm (one point five millimeter) thick MS Sheet duly stove enameled paint in white colour in front and gray colour on back with red reflective border of 65mm (sixty five millimeter) width and required letters and figures with reflective tape engineering grade of required shade and colour supported and welded on 47mmx47mm (Forty seven millimeter into forty seven millimeter) of 12 SWG sheet square tube firmly fixed to the ground by mean of properly designed foundations with M-15 (M-fifteen) grade cement concrete 450x450x600 mm, (four hundred fifty into four hundred fifty into six hundred millimeter) 600mm (six hundred millimeter) below ground level as per drawing and MORD technical specification section 1700 including painting angle iron post with primer and two coats of epoxy paint and as per direction of Engineer-In-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including Royality, Malkana, Octroi, toll tax, GST or any other taxes imposed by the Government

Providing and Fixing Glow stud of size 100x20 mm (one hunded in to twenty milimetre)made of heavy duty body shall be moulded ASA (Acrylic styrene Acrylretrite) or HIP (High impect polystyrene) or ASB having electronically welded micro-prismatic lens wih abrasion resistant coating as aproved by Engineer-in-Charge. The glow stud shall suported a load of 13635 kg. tsted in accordanc wih ASTM D4280. The slope of retro-reflective surface sall be 35(+/-5) degree to base. the reflective panels on both side with at least 12 cm (Tewelve centimetre) of refelective area up each side. The Luminance intensisty should be as per the specification and shall be tasted as per described in ASTM I: 809 as reccommended in BS: 873 part 4:1973. The stud shall be fixed to the Road surface usein the adhesive conforming to IS(Indian Standred) as per procedure reccommonded by the manufacturer complete and as per direction of Engineer-in- Charge including carriage of materials and equipment with all mode of transportation and as per direction of Engineer- in- Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, GST or other taxes imposed by the Government.