Jal Jeevan Mission (JJM)-JJM 2022-23 Pavaratty Regional Water Supply Scheme - Phase III

Amount

Supply, Erection, Testing and Commissioning of One No. 1250 KVA, 11 KV/3.3KV Transformers & Providing gantry crane

OD249396/2023-2024:Supply of all materials and providing 11KV Double pole structure using 2nos. 175x85mm. ISMB joist of 9.5M height, 100x50mm. GI chanel cross arms, 1set 3 pole of 400A, 11KV gang operated AB switch with operating handles of required length,1 set of 9.6KV,6KA Lightning Arrestors, 1 sets (3 nos) of 11KV, D.O fuses, Pin insulators, Disc insulators and inter connections of the above items using 8mm dia copper wire with proper copper sockets , including all associated civil works and painting of all structurers with two coats of zinchromate primer and aluminium paint etc. and earthing using 5 nos of 3m GI earthing pipes and inter connection complete as per standard construction practices approved by Kerala Electrical Inspectorate and relevant standards

OD249398/2023-2024:Supply of all materials and providing substation yard fencing using 50 x 50 x 6mm angle iron frame work of size 1500x2500mm

OD249399/2023-2024:Supply of all materials and providing 2000mm wide 2500mm height weld mesh gate made out of 50 x 50 x 6mm Angles

OD249400/2023-2024:Supply,erection, testing and commissioning of , 1250 KVA, 11KV/3.3KV. 3phase, 50Hz,Dyn 11,. ANAN cooled , Indoor type copper wound distribution transformers, with HV and LV side cable end box arrangements, on load tap changer with AVR with 17 tap positions having 5% to -15% variations in1.25% steps with RTCC panel etc. complete with all fittings as per IS 1180 L2 and Kerala Electrical Inspectorate norms and conforming to IS1180 ( Part 1 ). Armoured multi core 2.5 Sqmm copper control cables shall be used for all external & internal interconnections . The cost of control cables both internal and external shall be included in the cost of Transformer." Including automatic OLTC unit

OD249401/2023-2024:Supply, erection, testing and commissioning of 11KV, 630A, 350MVA, 26.3KA,3sec totally enclosed, single bus bar, floor mounting in metal clad, indoor extensible type flush mounted horizontal isolation and draw out type 3 Panel vacuum circuit breakers fitted with manual/motor operated spring charge mechanism with 230V AC motor and motor control switch, shunt trip coil of 24 volt DC auxiliary contact 6NO+6NC, Mechanical ON/OFF indicator, Mechanical operation counter, Anti pumping feature, Automatic safety shutters and push button etc, three panel system (1 no. VCB as incomer and 1 Nos. VCB and 1 No LBS as outgoings ) suitable for installation in 3 phase , 3wire, 50Hz. AC,11kv, effectively earthed supply system,comprising of motorised and spring assisted, with all protective relays as per standard etc. along with metering panel consisting of resin cast 11KV/110V , PT ,150VA Class 0.2S and * /5A , Class 0.2S ,15VA resin cast current transformers(3Nos) in each bus for KSEB metering and provision for fixing TOD Meter with sealing arrangement and with controlling fuses for both side and Dual core CT , LED panel lamps , panel heaters etc complete as approved by Kerala Electrical Inspectorate and relevant standards. Armoured multi core 2.5 Sqmm copper control cables shall be used for all external & internal interconnections. The cost of control cables both internal and external shall be included in the cost of HT panel, 11KV Switchgear (Indoor)

OD249402/2023-2024:Supply,erection, and commissioning of Static TOD meter- Supply,erection, and commissioning of Static unidirectional TOD meter , -/5A , 11KV/110V, 3 phase 4 wire, Class 0.2S , with data downloading facility as per KSEBL standards

OD249403/2023-2024:Supply, erection, testing and commissioning of 3.3KV, 630 A, 26KA, VCB panel totally enclosed, single bus bar, floor mounting in metal clad, indoor extensible type flush mounted horizontal isolation and draw out type panel board comprising of 1No 3.3KV 630A,26KA Vacuum Circuit Breaker as incomer, 3nos. 3.3KV 630A ,26KA Vacuum Circuit breakers as outgoing The incomer switchgears, & outgoing switch gears should be of draw out type trip free VCBs .The outgoing VCBs shall be provided with Instantaneous IDMT relay with Microprocessor based 3O/C +1EFR relay and Incomer shall be provided with Instantaneous IDMT relay with Microprocessor based 3O/C +1EFR and REF relay through the neutral CT provided, suitable UV and shunt releases for probable integration to control wiring including PLC unit and its auxiliary systems for remote monitoring and operation and provision for future up gradation to SCADA, suitable for installation in 3 phase , 3wire, 50Hz. AC, 3.3kv, effectively earthed supply system, comprising of motorized and spring assisted, independent, trip free closing mechanism and all metering equipment, MC 61A high set numerical protective relays, . resin cast, 3.3 KV /110V/230V PT with control fuse for incomer dual core CT for ammeter and protections, LED panel indicators, digital multi-function meters, with minimum features to read KWh,V, A, Hz, PF, THD % in all the outgoing feeders and incomers including suitable CT/PT and protection arrangements, panel, heaters with timer/RTD based automatic operation, suitable SMF battery and battery charger arrangements etc.. Complete as approved by Kerala Electrical Inspectorate and relevant standards. Armoured multi core 2.5 Sqmm copper control cables shall be used for all external & internal interconnections. The cost of control cables both internal and external shall be included in the cost of 3.3KV panel, 3.3KV Switch gear

OD249404/2023-2024:Neutral Grounding Resistor, Design,engineering, supply erection,testing and commissioning of indoor type 3.3KV stainless steel make neutral grounding resistor in sheet steel enclosure with IP 23 degree protection with siutable neutral CT for REF protection. The cubicle shall be fabricated out of 3mm sheet steel and painted with anti –rust primer coating followed by two coats of paint of approved shade, as per standards. The resistance shall be of Kerala Electrical Inspectorate and relevant standards. Armoured 2.5 Sqmm copper control cable shall be used for all external interconnections. The cost of control cables both internal and external shall be included in the cost of NGR

OD249405/2023-2024:Supply, erection, testing and commissioning of , 63 KVA, 11KV/433V. 3phase, 50Hz,Dyn 11,. Resin cast , Indoor type copper wound distribution transformers, with HV and LV side cable end box arrangements complete with all fittings as per IS 1180 L2 and Kerala Electrical Inspectorate norms and conforming to IS1180 ( Part 1 ). Armoured multi core 2.5 Sqmm copper control cables shall be used for all external & internal interconnections . The cost of control cables both internal and external shall be included in the cost of Transformer.

OD249406/2023-2024:Supply ,installation,testing and commissioning of MSB panel board for 63KVA Transformer with incomer-1no 125A microprocessor based mccb with 3 O/C and E/F release and stand by earth fault relay as and outgoing 100A 4p MCCB-1 nos, 63A 4p MCCB -4nos, EFR,neutral ct, indications,MFM with RS485 1 nos, voltmeter, 1 nos ammeter with suitable current transformer, suitable busbar and control wiring etc

OD249407/2023-2024:HT Power Cables - Supply & laying 11KV stranded compact circular aluminium conductor, conductors screened with extruded semi conducting compound XLPE insulated, insulation screened with extruded semi conducting compound in combination with copper tape (0.3 kA for 1 sec.), cores laid up, inner sheath of PVC tape, galvanized steel flat strip armoured, and overall PVC sheathed cable of the following sizes in the existing cable trench conforming to IS: 7098 part II 1985 with latest amendments. 3C x 300 Sqm

OD249408/2023-2024:HT Cable Terminations - Supplying and making outdoor cable end termination with heat shrinkable jointing kit, including lugs and other jointing materials, for following sizes, XLPE aluminium conductor cable of 11 KV grade as required. 3C x 300 Sqmm

OD249409/2023-2024:HT Cable Terminations - Supplying and making indoor cable end termination with heat shrinkable jointing kit, including lugs and other jointing materials, for following sizes, XLPE aluminium conductor cable of 11 KV grade as required. 3C x 300 Sqmm

OD249410/2023-2024:HT Power Cables - From 11KV Panel to 63KVA Transformer- Supply & laying 11KV stranded compact circular aluminium conductor, conductors screened with extruded semi conducting compound XLPE insulated, insulation screened with extruded semi conducting compound in combination with copper tape (0.3 kA for 1 sec.), cores laid up, inner sheath of PVC tape, galvanized steel flat strip armoured, and overall PVC sheathed cable of the following sizes in the existing cable trench conforming to IS: 7098 part II 1985 with latest amendments. 3C x 150 Sqm

OD249411/2023-2024:HT Cable Terminations - Supplying and making indoor cable end termination with heat shrinkable jointing kit, including lugs and other jointing materials, for following sizes, XLPE aluminium conductor cable of 11 KV grade as required. 3C x 150 Sqmm

OD249412/2023-2024:Supply and providing plate earthing as per IS 3043 with 1200x1200x12 mm GI/CI earth plate, 50 mm GI watering pipe fixed to the earth plate with 25 x 3mm GI clamps, GI funnel with weld mesh, filling required quantity of charcoal including construction of inspection chamber with a bed concrete of 1:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar 1:6, plastering the surface of brick masonry and the exposed surface of PCC bed with cement mortar 1:4, 12 mm thick, (the finished inside dimension shall be 450 x 450 x 450 mm) but excluding test joint, earth continuity conductor to the plate, and covering at the top.

OD249413/2023-2024:Supply of all materials and providing end termination of the following size/suitable size PVC/XLPE insulated, sheathed armoured Aluminium conductor cable for giving power connections to HT Breaker, Transformers, Panel boards etc. complete as per standards.3 core 240 Sq.mm.3.3kv,XLPE AL Cable(Indoor)

OD249414/2023-2024:Supply and laying,testing and commissioning of fallowing size/suitable size XLPE insulated PVC sheathed Armoured Alluminium conductor cable(3.3kv grade) clamped on wall/ceiling with clamps partly laid in trench and partly in cable tray,3core 240sq.mm,3.3kv grade XLPE Alluminium UG cable laying from transformer LV side to 3.3kv pannel (incomming side)

OD249416/2023-2024:Conveyance and Testing Charges -Testing the metering equipments including To and Fro conveyance for testing the metering equipments (CT/PT unit and meter) at TMR testing Lab of KSEBL

OD249417/2023-2024:Supply,erection, testing and commissioning of 8 way vertical MCB distribution board comprising to the following. 63A 4 pole MCB 1 No. as incomer with 63A 100mA ELCB and 20A TP MCB-2Nos. & 20A SP MCB- 6 Nos each. as outgoings, With tinned copper busbars/cables, interconnection, housed in a suitable metal enclosure as per KEI standards fixed in open system

OD249418/2023-2024:Supply,erection, testing and commissioning of MCB distribution board comprising to the following. 40A TPN 4 pole MCB 1 No. as incomer with 40A 30mA ELCB, 18 nos 6 AMPS SP MCB as outgoings, With tinned copper busbars/cables, interconnection, housed in a suitable metal enclosure as per KEI standards fixed in open system

OD249419/2023-2024:Supply, laying, testing and commissioning of the following size PVC/XLPE insulated, sheathed armoured Aluminium conductor cable (1100 volts grade) clamped on wall/ceiling with clamps and saddle clips partly laid in cable tray/partly laid in trench 3.5 core 50Sq.mm. AYFY Cable

OD249420/2023-2024:Supply, laying, testing and commissioning of the following size PVC/XLPE insulated, sheathed armoured Aluminium conductor cable (1100 volts grade) clamped on wall/ceiling with clamps and saddle clips partly laid in cable tray/partly laid in trench. 4 core 16 Sq.mm.PVC AL. Cable

OD249421/2023-2024:Supply of all materials and providing end termination of the following size PVC/XLPE insulated, sheathed armoured Aluminium conductor cable ( 1100 volts grade ) for giving power connections to Panel boards etc. complete as per standards. 3.5 core 50Sq.mm. AYFY Cable

OD252229/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5C x 25 Sqmm

OD252230/2023-2024:Supply & laying of one number 3.5C x 35 Sqmm PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground /Cable Tray

OD249422/2023-2024:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required - 4C x 16 Sqmm

OD249423/2023-2024:PIPE EARTHING WITH 2.5M PIPE -Supply and providing pipe earthing as per IS 3043 with 2.5 m long 40 mm dia B class GI pipe, GI funnel with weld mesh, filling required quantity of charcoal & salt including construction of inspection chamber with a bed concrete of 1:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar 1:6, plastering the surface of brick masonry and the exposed surface of PCC bed with cement mortar 1:4, 12 mm thick, (the finished inside dimension shall be 300 x 300 x 300 mm) but excluding test joint, earth continuity conductor to the plate, and covering at the top.

OD249424/2023-2024:Supply,laying and termination of the following sizes of copper strip/wires for earthing of substation, transformers, HT panel boards, LT panel boards, equipments and inter connection of earth pits etc. 25x6mm copper strips.

OD249425/2023-2024:Supply,laying and termination of the following sizes of copperstrip/wires for earthing of substation,transformers, HT panelboards, LTpanel boards, equipments and inter connection of earth pits etc. 32x6mm GI strips.

OD249426/2023-2024:Supply,laying and termination of the following sizes of GI Strip for earthing of substation, transformers, HT panel boards, LT panel boards, equipments and inter connection of earth pits etc. 50x6mm GI strips.

OD249427/2023-2024:ON-OFF Push button station with Emergency Off button in suitable weather proof enclosure and fixing near the motor including supply laying and termination of control cable.

OD249428/2023-2024:Supply and fixing of 6mm thick chequered plate with required M.S. angle/plate supports over the masonry cable trench at substation and electrical control room. Angle and plate should be painted one coat of primer and two coats of enamel paint as required.

OD249429/2023-2024:Supply and fixing of M.S. angle cable tray for clamping the various sizes of cables in trenches, through walls,& trusses etc. as per KEI standards

OD249430/2023-2024:Supplying, fixing, testing and commissioning of Lead acid cell battery 24V, 200AH capacity at 10hrs rate of discharge assembled with plante positive and pasted negative plates with inter cell, inter raw, interior connectiors etc. stand and cell insulators, sealed floats, nuts, bolt, washersetc with electrolyte of specific gravity 1.190 and accessories such as voltmeter, Thermometer, Hydrometer, spaners etc with teak wood stand with 3 coats of antiacid paint to accomodate battery.

OD249431/2023-2024:Supplying, fixing, testing and commissioning of automatic twin battery charger with distribution board with all instruments and protective devices etc. complete as per standards.

OD249432/2023-2024:Supply and providing the following safety items approved by Kerala Electrical Inspectorate and relevant standards.

OD251454/2023-2024:Transportation charges of Transformers, 11KV Panels, 3.3KV Panels ,MSBs and SSBs from the manufacturers site to the pump house taking all precautions.

OD249433/2023-2024:Amount for preparation of drawing and fees towards Electrical Inspectorate,obtaining necessary approval from Electrical Inspectorate etc and for misc items

OD249434/2023-2024:Supply, delivery and fixing of 7 T or suitable capacity electrically and manually working on single girder with over head travelling trolley and clear lift as per site conditions for lifting the chemicals, chlorine , pumps etc. and fitting as required, supplied with one set of crane slings with GI D shackle and clamps etc. complete as per the instruction of engineer in charge

Supply erection testing and commissioning of VT Pumpsets

OD249435/2023-2024:Supply, erection, testing and commissioning of VT Pumpsets having a minimum discharge of 198.61 lps against a total head of 97m. The rates suggested above include for supply, erection, commissioning and maintenance for two years of pump sets of different duty conditions with motor ,starter etc. The speed specified is 1500 rpm and overall efficiency of 70%. The rates include the following items: 1. Cost of VT pump. 2. Cost of motor 3Phase, 3.3KV,4P, Squirrel cage Induction Motor with motor protection sensors and relay. 3. Cost of panel board having suitable VCBs of adequate capacity with necessary protections with interlocking facility to run 2 motors at a time –(VCBs can also be integrated with the Soft starter panels in suitable metal enclosure with necessary bus bar inter links and mechanical interlocks). 4. Cost of 3.3 KV Soft starter with motor protection relay and bypass contactor. 5. 3.3KV grade Aluminium cable from panel board to starter and from starter to motor (total length of 10 m) 6. Capacitor- Capacitor 3.3KV in metal enclosure suitable for 390HP, 3.3KV,1500RPM motor so as to maintain the power factor above 0.95. 7. Suction pipes for a total length of 10 m. 8. Foot valve suitable for the pump. 9. Non return valve and Sluice valve. 10. Pipe connection works for suction side and that at delivery side up to valves including fixing of Non return valve and Sluice valve. 11. Suitable earthing of motors to the main earth bus as per IS standard and CEA regulations. 12. Erection charges of all equipments including foundation cost of cement sand and metal. 13. Trial running and commissioning. 14. Maintenance during a period of two years. 15. Inspection of pump/motor/starter/panel board for pump sets .

Construction of pumphouse, operators room, toilet.

2.31:Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

5.33.1:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work upto plinth level

5.33.2:Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.All work above plinth level upto floor V level

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.7:Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.2:Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.83.2:Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour.Two coats

13.71:Lettering with black Japan pint of approved brand and manufacture

10.26.1:Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.M.S. tube

9.117.1:Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 48x40 mm

9.124.1:Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mm x 1 mm, painted with primer, all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (Push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5 mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rails of sixe 100mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100 mm x 8 mm complete as per manufacturer's specifications and direction of Engineer -in-charge.Non decorative finish

10.6.1:Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

50.9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

50.9.3.1:Providing and fixing paneled or paneled and glazed shutters for doors, windows and clerestory windows, 30 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding paneling which will be paid for separately, all complete as per direction 0f Engineer in- charge. using Anjili/ Jack wood

11.37:Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

17.1.1:Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

17.7.1:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Construction of valve chamber1 - 700mm DI pipe-1904m

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Interconnection of Work- Cost of Materials

100.98.125:Supply of DI K9 Pipe Conforming to IS 8329/2000, 700mm Dia.

OD249436/2023-2024:Supply of butterfly Valve 700mm Conforming to IS 14846 - 2000.

18.68.2:Providing and laying D.I specials of class K - 12 suitable for push - on jointing as per IS : 9523 :Above 600 mm dia

100.37.22.1:In situ fabrication of M.S. pipes of size 700mm (I.D.) using 10mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete.

100.37.22.2:Fabricating M.S. flanges of diameter 700mm using 16mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 10mm thick M.S. plates.

100.37.22.3:Cutting 700mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 10mm thick M.S. plates.

100.37.22.4:Welding 700mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 10mm thick M.S. plates.

100.37.22.5:Grinding cut and weld edges of 700mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 10mm thick M.S. plates.

OD249437/2023-2024:Fabricating and Supplying 700mm dia MS Tee, with flange by cutting, chamfering and three runs welding using 10 mm thick MS pipe to provide a smooth flow of water without resistance to the water flow including all cost of electrodes, hire charges of gas, cutting equipments, welding set, tools and labour charges etc. but excluding cost of pipe and fabricating MS flanges of dia 700mm using 16 mm thick MS plate including cost and conveyance charges of MS plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc. complete : For pipes fabricated with 10mm thick MS Plates: Tee - 2 m

OD249438/2023-2024:Fabricating and Supplying 700mm dia MS D/F 90°Bend with flange by cutting,chamfering and three runs welding using 10 mm thick MS pipe to provide a smooth flow of water without resistance to the water flow including all cost of electrodes, hire charges of gas, cutting equipments, welding set, tools and labour charges etc. but excluding cost of pipe and fabricating MS flanges of dia 700mm using 16 mm thick MS plate including cost and conveyance charges of MS plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc. complete : For pipes fabricated with 10mm thick MS Plates: 700 x 90° Bend - 1.20 m

OD249439/2023-2024:Fabricating and Supplying 700mm dia MS D/F 45°Bend with flange by cutting,chamfering and three runs welding using 10 mm thick MS pipe to provide a smooth flow of water without resistance to the water flow including all cost of electrodes, hire charges of gas, cutting equipments, welding set, tools and labour charges etc. but excluding cost of pipe and fabricating MS flanges of dia 700mm using 16 mm thick MS plate including cost and conveyance charges of MS plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc. complete : For pipes fabricated with 10mm thick MS Plates: 700 x 45° Bend - 1.20 m

Interconnection of Work- Working Charges

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Bidder Name

Electric Project Consultants