SPL REPAIR TO BLDG NO. P-04 and P-5 (SINGLE OFFICER ACCN) OF 625 EME BN AND BLDG NO. T-41 (OR LIVING LINE) OF 898 AT BN ASC AT RAJOURI UNDER GE 862 EWS

Amount

Demolition of cement concrete (unreinforced) including tile and floor finishes in ground floors and paving n exc 15 cm th (below or above ground level) complete all as specified and as directed.

Demolition of Reinforced cement Concrete in Roofs,floors ( other than ground floors) , beams,staircases,landings,chajjas,lintel band and similar suspended works.(reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, internal dia of pipe 150mm, complete all as specifed & directed.

Taking down cement plaster and lime plasterof any thickness on brick/stone or conc surfaces including racking out joints hacking for key to any thickness scrubbing down with water etc.complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified.

Dismantling Plain or corrugated steel sheeting or any other type, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

Dismantling existing PVC water tank exc 250 litres and n.exc 500 ltrs capaicty and removing to store.complete all as specified and as directed.

Dismantling timber scantling over 40 sqcm in section in any position.complete all as specified and as directed.

Taking down chowkhats with shutter (without taking off from shutter) exc 1.5 sqm and n exc 4 sqm each and removing to store and making good to surface disturbed due to taking down complete all as specified and as directed.

Taking down chowkhats with shutter (without taking off from shutter) n exc 1.5 sqm each and removing to store.complete all as specified and as directed.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, hoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories), complete all as specifed.

Taking up or down steel tubing and connections of 15 mm bore including cleaning for refixing and removal to store, complete all as specifed.

Taking up or down steel tubing and connections of 20 mm bore including cleaning for refixing and removal to store, complete all as specifed.

Hacking out old broken glasses (Any thickness, size quality, description) from wooden or steel frames fixed with putty or wooden beads.complete all as specified and as directed.

Brickwork with sub-class ‘B’ bricks (old size), straight or curved on plan exc. 6m in mean radius, built in cement mortar 1:6, complete all as specified.

Filling of bitumastic gola , with 80/25 bitumen and coarse sand mixture , 1:3 by weight in PCC joints of 50 mm deep x 6 mm wide complete all as specified.

RCC (1: 2 :4) type B-1 using 20mm gradded stone aggregate as in beams, deck slabs , chajjas and in shelves and like complete all as specified and as directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified & directed.

Form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beams for rough finished surfaces of concrete, complete all as specified & directed.

Form work to edges of concrete flats, treads, break in floors, window cills, concrete railings openings in concrete walls, floor and roof and exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 5cm but n. exc. 10cm wide for rough finished surfaces of concrete, complete all as specified & directed.

TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, conforming to grade Fe-500, complete all as specified& directed.

All as per Srl item No. 21 above but 5mm dia & over upto & including 10mm dia in stirrups, spacers and binders.

Rolled mild steel work in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary length i.e. within 20mm of the length indicated), conforming to Fe-290 grade -165, complete all as specified & directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/ cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based plain sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, hips, valley gutters fixed with self tapping screws including side and end lap as per manufacturer’s instructions, complete all as specified and directed.

15 mm thick plastering in cement mortar 1:6 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified.

10 mm thick plastering in cement mortar 1:6 on stone masonry surfaces of fair faces of brick surfaces, finished even and smooth without using extra cement, complete all as specified.

10 mm thick plastering in cement mortar 1:6 on stone masonry surfaces or other than fair faces of brick surfaces, finished even and smooth without using extra cement, complete all as specified.

15 mm thick plastering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement but using integral water proofing compound as per manufacturer,s instructions, complete all as specified. Note : Integral water proofing compound shall be measured & paid seprately.

5 mm thick plastering in cement mortar 1:3 on concrete surfaces of ceiling, surface finished even and smooth without using extra cement, complete all as specified.

Supply only water proofing admixture, complete all as specifed.

75 mm thick PCC 1:3:6 type, C-2 (40mm graded aggregate) as in floor laid in alternate panels finished even and fair without using extra cement ,laid in alternate bays complete all as specified and directed.

75 mm thick PCC 1:3:6 type, C-2 (40mm graded aggregate) as in plinth protection, surface finished even and fair, complete all as specified.

PCC 1:2:4 type B-1 using (20 mm graded crushed stone aggregate) as in bed blocks, bed blocks of hold fasts, coping, PCC cill etc, complete all as specified and as directed.

Plain cement concrete type B-1, 1:2:4, (using 20 mm graded stone aggregate) for embedding hold fasts as directed including necessary form work as required complete all as specified and directed.

COLOURED Glazed ceramic tiles in vertical surface ( 600x300x7mm / 450x300x7 mm thick ) set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over 10mm thick screed bed in CM 1:3 complete all as specified and as directed.

Coloured Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over 10mm thick screed bed in CM 1:4 complete all as specified and as directed.

Vetrified ceramic tiles in light shade 600x600x7-10 mm thick as in floor set and jointed in neat cement slurry and pointing in white or coloured cement to match the colour of tiles over 10mm thick screed bed in IN 1:4 complete all as specified and as directed.

Machine cut kota stone in slab flooring 18-20 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of slab including grinding, rubbing ,polishing to mirror finish complete over 20mm thick screed bed in cement mortar 1:3 including dismantaling of old any type ,complete all as specified and as directed

Description as per srl item no. 47 above but as in riser to steps, skirting ,dado,window cills fixed over 10mm thick cement mortar 1:3, complete all as specified and as directed.

Granite 18-20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade, complete all as specified and as directed.

Chequered cement concrete tiles, machine pressed, factory made of size 30cmx30cm, 25mm thick, with grey cement and no pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified.

Steel windows with side hung shutters including box type hinges with steel handle 100mm long, made of Z section and steel peg stay, complete with glazing bars, dovetailed or welded cpmplete all as specified and as directed.

Steel windows with side hung shutters including box type hinges with steel handle 100mm long, made of Z section and steel peg stay, complete without glazing bars, dovetailed or welded cpmplete all as specified and as directed.

Pressed steel frames of size 125mmx60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate., complete all as specified. Note : PCC for filling of hollow portion shall be measured and paid for separately.

S & F for power coated of any colour (Thickness or powder coating not less than 50 micron) aluminium anodized three track sliding window with two or more shutter with 4 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle lock, etc including 65 x 39.5x 1.5 mm section for complete frame and rubber beading and glazing clips etc., complete as specified and directed by Engr-in-Charge. Note : Unit rate quoted shall be deemed to include for cost of glass/ss wiremesh rubber beading, glazing clips, neoprene packing, fittings such as handles, butt hinges, tower bolts etc

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows,ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottomand sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.

2nd class soft wood (kail), plain framed , panelled shutters (any numbers of panels), 35mm thick, with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied & fitted to chowkats, complete all as specified.

2nd class soft wood (kail), glazed and skeleton shutters, 30mm thick, open rebated and prepared to receive glass or gauge etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in clause 8.24 (a) of SSR Part-I for door shutters, complete all as specified.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement from stiles and plained colour PVC sheet to be fitted with MS frame welded/sealed to the styles & rails with suitable PVC sheet beading, and jointing together with solvent cement, supplied & fitted in the frame at site as per specification & drawings shown in SSR Part-II, complete as specified.

S & F for aluminium powder coated of any colour door with one or more shutters aluminium section weighing 0.55 kg/m including 5 mm thick plain/ coloured/ frosted sheet glass or ACP sheet and stainless steel wiremesh and connected items such as necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, pegstays 150mm long , hinges type B-21 100mm long , suitable handle, alum tower bolt including mortice lock, aluminium hydraulically door closer and brass door stopper, complete all as specified and directed. .(Note :- Minimum thickness of powder coating not less than 50 micron).

S & F for aluminium powder coated of any colour window and ventilator with one or more shutters fixed / side hung type without sash bar , aluminium section weighing 0.55 kg/m including 5mm thick plain/ coloured/ frosted sheet glass, stainless steel wiremesh and connected items such as necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, pegstays 150mm long, hinges type B-21 100mm long , suitable handle, alum tower bolt complete all as specified and directed.(Note :- Minimum thickness of powder coating not less than 50 micron).

M & L in repair door bottom sealing strip guard with double sided insulation for doors, which are equally able to keep wind, dust and sound or poluted air out side of door (i.e. Anti Lizard strip) fixed to aluminium or pannel door all as specified and directed

Extruded aluminium alloy handle, fabricated type, anodised, 125 mm long (ISI marked), complete all as specified.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

Sheet glass 4.00 mm thick ordinary quality and glazing with oil putty or wooden beads in squares exc. 0.5 Sqm in each pane, complete all as specified.

Mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or beading etc, complete all as specified.

Butt hinges, medium weight, cold rolled, mild steel 100 mm long (ISI marked), complete all as specified.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 150mm long (ISI marked), complete all as specified.

Extruded aluminium alloy handle, fabricated type, anodised, 150mm long (ISI marked), complete all as specified.

Extruded aluminium alloy handle, fabricated type, anodised, 125 mm long (ISI marked), complete all as specified.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm, complete all as specifed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or excluded sections and fixing bolts and sliding bolts of excluded sections or cast aluminum alloy and fixed, 300mm long, complete all as specified.

S&F in repair for Curtain Rod of stainless steel 20 mm dia fancy type complete and hanging hooks/brackets / end caps of length 1.5 mtr to 1.8 mtr complete all as specified and directed.

S&F in repair stainless steel T and L type brackets with finials complete all as specified and directed.

S&F in repair aluminium anodized grills 6.3 mm dia decorative type with 75 mm mesh complete all as specified and directed.

Providing & fixing of 4mm thick designer ceiling board in ceiling fixed with screw as per manufactures instructions, laid on hot dipped galvanized iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick galvanized steel sheet & of size 24x32x300mm and spaced at 12mm centres securely fixed to the structural soffits by approved hangers at 1200mm maximum centres. Hangers of GI wire 4mm dia to be fixed by approved rowl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200 long cross tee with (double stitching) to be inter locked between main runners at 600mm centre to from 1200x600mm modules cross tee longer than 600mm modules to be formed by fitting 600mm long cross tee, tee perimeter wall angle shall be of 0.45mm thick galvanized steel of size 19x19mm and 300mm long of white colour all as per instruction complete all as specified & directed.

GI water tubing, medium grade, 15mm bore with all fittings, fixed complete to walls and ceilings or laid in floors, complete all as specified.

GI water tubing, medium grade, 20 mm bore with all fittings, fixed complete to walls and ceilings or laid in floors, complete all as specified.

S & F in repairs for 15 mm dia Fancy type Chromium plated Angle valves, cast copper alloy screwed down high pressure, with crutch or butterfl y handle, screwed both ends for iron pipe or for unions and fixed complete all as specified.

S&F in repair CP Bib tap cast copper alloy with crutch or butterfly handle, chromium plated fancy type screwed for iron pipe, suitable for 15 mm bore complete all as specified.

S&F in repair Gun-metal, globe or gate valves of 15 mm dia, with iron wheel head, screwed both ends for iron pipe, complete all as specified.

S&F in repair Gun-metal, globe or gate valves of 20 mm dia, with iron wheel head, screwed both ends for iron pipe, complete all as specified.

S & F in repairBall brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule for bore of pipe 20mm, complete all as specified.

S&F in repair Stop valve cp cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm dia pipe, complete all as specified and as directed.

S&F in repair WC Orissa pattern white with integral foot rest 580x 440 mm including, PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified.

S&F in repair for vitreous china water closet pedestal pattern in one piece type of dimention 73cm X 36cm X 74cm including seat cover and gaset, floor mounted 'P'or 's' trap,flushing kit' CP jet with PVC pipe of superior quality and all necessary fixing arrangements complete all as specified and as directed.

S&F in repair PVC low level flushing cistern 10 ltrs capacity white with inlet ball value, float valve and handle incl brackets, PVC flush pipe complete all as specified and as directed.

S&F in repair Hand shower ( health faucet ) with 8mm dia 1.2 meter long flexible braided chromium plated tube with wall hook.complete all as specified and as directed.

S & F in PVC waste pipe900mm long , 15 mm size suitable for Wash hand basins and urinals including connecting all as specified and as directed.

PVC connections 15mm size with PTMT nuts of length 600 mm, complete all as specified.

Cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), dia of outlet 75mm, complete all as specified.

Sail-glazed stoneware drain pipes 150 mm laid in trenches and jointed as specified complete all asspecified & directed.

S&F in repair PVC (SWR) pipes, 110mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified & directed.

S&F in repair PVC (SWR) pipes, 75mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified & directed.

110 mm bore PVC (SWR) bends any radius, fixed in repair complete all as specified.

75 mm bore PVC (SWR) bends any radius, fixed in repair complete all as specified.

Brass chromium plated shower rose of 125mm size with or without swivel joints, fixed in repair complete all as specified.

Towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges, fixed in repair ,complete all as specified.

Vitreous China, wash hand basin, flat back white of size 550mmx400mm with pedestal to match including brackets, including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs, complete all as specified.

Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap, bore of trap 32mm, fixed in repairs, complete all as specified.

Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanksand fly-nuts, flange endbedded in red lead cementand other end fixed, fixed in repairs, complete all as specified.

Stainless steel sink with drainage board made of stainless steel 1mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever cast iron bracket, connecting union etc. and overall size 915x460mm with bowl size 410x330x160mm, . fixed in repair complete all as specified.

15 mm bore centre hole Brass CP mixer for mixing hot & cold water screwed down for iron pipe, fixed in repair complete all as specified.

Wall mixer with shower for mixing hot & cold water, 15mm bore, fancy type, brass chromium plated, , screwed for iron pipe, fixed in repairs, complete all as specified and directed.

Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms), dia of discharge pipe 32mm, chain and plug, porcelain stopper, fixed in repair, complete all as specified & directed.

S&F in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) , complete all as specified.

S&F CP soap dish 100 x 100 x 60 mm with and including rowel plugs and s s screws complete all as specified.

S&F in reapir C P toilet paper holder fixed to wallwith brass CP screw complete all as specified.

S&F in reapir C P towel ring 20 mm with brass CP screw complete all as specified.

Six peg set with 4 mm thick base plate stain less steel fixed with and including rowel plugs and stainless steel screws. complete all as specified.

Glass corner shelf with chromium plated guard rails fiexed with and including stain less steel screws and rowel plugs. Fixed in repair complete all as specified.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed in repair, complete all as specified.

S & F bathroom cabinet of hard thermosetting plastic of size 600x450mm, fitted with superior quality distortion free 4mm thick mirror complete as specified and directed by Engr - in - Charge.

S & F in repair assembled ready to use rectangular stainless steel (Grade 304) kitchen plate rack with 3-4 shelves, enclosed four sides by SS plain sheet, 0.6mm square support pipes, dedicated holes for spoon, pegs etc over all size 600mmx750mmx250mm of standard pattern complete all as specified.

Rotationally moulded polyethylene water storage tank (cylindrical vertical with closed top) hoisted & fixed in position of capacity 500 ltrs, complete all as specified.

preparation of new plastered wall surface including cornices etc and applying two coats of exterior emulsion all weather proof paint of Apex Ultima of ASIAN or equivalent make of any approved two or more colour pattern as specifed by Engr - in - Charge over and including a coat of primer all as directed and as approved..

Preparation of new plastered surfaces of wall and applying two coats of oil emulsion distemper over one coat of alkali-resistant priming paint including 1 mm thick wall care putty, complete all as specified.

Preparation of new plastered surfaces of celling and applying two coats of oil emulsion distemper over one coat of alkali-resistant priming paint including 1 mm thick wall care putty, complete all as specified.

Preparation of new plastered surfaces of wall and applying two coats of exterior all weather coat paint of apex over and including a coat of primer, complete all as specified.

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and efflorescent salts, trading oil, greasy spots etc.and applying two coats of oil emulsion distemper over one coat of alkali-resistant priming paint, complete all as specified.

Preparation of old decorated plastered or unplastered surfaces of walls by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and efflorescent salts, trading oil, greasy spots etc. and applying one coat of exterior all weather coat paint of apex , complete all as specified.

Prepration of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified.

Prepration of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified.

Complete removal of existing water proofing treatment over RCC roof, projections of any thickness, non approachable/ non accessible, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with wire brush including removing debris from the site and depositing in low lying area where directed and providing following :- (a) Rendering 10mm thick in cement mortar 1:4 on concrete roof surfaces and finish the surface even and smooth without using extra cement including mixing water proofing compound @ 2% by weight of cement. (b) Apply a coat of bituminous primer confirming to IS-3384@ 0.4 ltr/Sqm on newly plastered surface after curing as per IS-456 and dried. (c) After the primed surface has dried, apply a coat of hot blown bitumen(85/25 penetration) confirming to IS-702 @ 1.2 Kg/Sqm of the surface.

(d) Provide polymeric water proofing membrane ISI marked laid with overlaps, bonded with hot blown bitumen, and laid by torch application method, end overlaps shall not be less than 150mm and side lap 75mm. Polymeric water proofing membrane should be five layered with centre core as 90 micron high molecular high density polyethylene film, min weight 3 Kg per sqm & minimum 3mm thick reinforced with polyster non wove fabric, APP membrane shall laid acorss the slop from lowest line of sloping roof towards ridge. (e) Over the APP membrane, apply a coat of semi hot blown 85/25 penetration grade bitumen confirming to IS-702 @ 1.20 Kg/ sqm and blinded with fine sand in dry condition @ 0.50 Kg / Sqm dusted over the bitumen coat Note : (i) Care shall be taken to avoid wrinkle and air gaps while sticking membrane to the bitumen applied surface. (ii) Ponding test shall be conducted for 72 hrs as directed.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5m in depth in any type of soil and getting out, complete all as specified and as directed.

Excavation in trenches not exc. 1.5m wide and not exc. 1.5m deep in soft / loose soil for laying of underground cable, foundation of poles & stays etc., and getting out, complete all as specified and as directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specifed.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified.

Sand cushioning to underground cables complete all as specified in clause 19.75 of SSR Part-I laid before and after laying of cable, complete all as specified.

Sub class ‘B brick, old size, brick covering laid dry, flat, transversally along the length of cable on sand cushioning, with width equal to the length of the brick, complete all as specified and directed.

Concrete bed to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid in cement concret 1:4:8 (Nominal mix) type D-2 using 40mm graded stone aggregate, and tested, complete all as specified & directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc complete all as specified and as directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

Taking down U/S aluminium point wiring (light, fan, socket or power ) complete including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials for taking credit (credit for above items should be made as per conditions seperately) and making good the disturbed complete all as specified and directed .

Point wiring for one light point/fan point /Exhaust fan point controlled by one switch with 1.5 sqmm PVC insulated FRLS unsheathed copper conductor two single core multi strand flexible cable and 1.5 sqmm PVC insulated FRLS unsheathed copper conductor single core cable (green color) as earth lead and including PVC conduit along with modular sunken boxes of reqd size with modular white cover plate with frame including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified. Note:- The rates are inclusive of cutting / chassis in wall & suitable PCC works including making good to disturbed surfaces.

Description all as per srl item No.130 above but for socket outlet 6 Amps on independent board complete all as specified and directed.

Description all as per srl item No. 130 above but for socket outlet 6 Amps 2/3 pin controled by one switch on same board complete all as specified and directed.

Description all as per Serial item No 130 above but for one 3 pin 15 Amp socket outlet independent with 2.5 sqmm PVC insulated FRLS multistranded copper cable with 2.5 sqmm single core multistranded FRLS copper cable as earthling lead complete all as specified and directed.

Modular switch piano, single pole, one way 10 Amp, 1 module, 240 volts complete all as specified and directed.

Modular switch piano, single pole, one way 6 Amp, 1 module, 240 volts complete all as specified and directed.

Socket modular socket outlet 2 in 1, 3 Pin 10 Amp 2 module complete all as specified & directed.

Socket modular socket outlet 2 in 1, 3 Pin 6 Amp 2 module complete all as specified & directed.

Modular switch single pole, one way 16 Amp, 1 module, 240 volts complete all as specified and directed.

Modular bell push 6A, 1 module, 240 volts complete all as specified and directed.

Modular switch single pole, one way 20 Amp, 1 module, 240 volts complete all as specified and directed.

Modular socket out let 2 in 1, multipurpose 6 & 16 Amp 2 module complete all as specified & directed.

Modular fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically complete all as specified and directed.

Ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body of size 60x50mm. complete all as specified and directed.

Bell ding dong by one push botton complete all as specified and directed.

LED Tube light fitting, 1x 20 watts. Decorative ultra slim linear LED lighting fixture with co extruded polycarbonate body, environmental friendly, energy efficient ready to use pack complete rewired, Premium 20 W LED batten, connecting electrically to ceiling rose to fitting using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core, including removing old/unsv, all as required at site or directed.

Lamp holder, insulated body, with back plate for batten fittings, in replacement complete all as specified.

LED lamp 9/12 W , B22 CDL suitable for lamp holder complete all as specified.

S & F in replacement LED light fitting 1 X 13.5 watt bulkhead luminaris including Led light driver holder connecting up with three core flexible copper conductor cable sutiable size complete all as specified.

Taking down fan, sealing cable, dismantlied blades and removing fan and blades to store and refixing ceiling fan and connecting up including provision of cable from ceilling rose, painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filing cavities with filler, one coat after cleaning all dust etc complete all as specified and directed.

Repair of exhaust fan motor with copper winding of sweep 300 mm complete including replacement of plastic blade with louvers shutter, complete all as specified and directed.

S & F in replacement Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification .(Note-MCBs will be measured separately.)

MCB, single pole, 6 to 32 Amp, with rupturing capacity 10 KA, 240 Volt, including removal of old unsv ,complete all as specified.

MCB, SPN, 6 to 40 Amp, with rupturing capacity 10 KA, 240 Volt, including removal of old unsv ,complete all as specified.

Supply and fixing LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including removing old/unsv, all as required at site or directed.

Bracket of GI pipe 40mm dia medium grade of length 1.20m and fixed with clamps made out of 50x6mm with nuts and bolts, complete all as specifed & directed.

GI water tubing, medium grade, with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc., in old existing or new routes, laid in trenches or under roads, bore of pipe 40 mm, complete all as specified & directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable sizecomplete all as specifed & directed.

S & F in replacement LED light fitting 1 X 9W /1 X 10 W bulk head luminairies including LED light driver holder etc complete with all acessories and including connecting up with three core flexible copper conductor cable of suitable size complete all as specifed & directed.

S & F in replacement High efficacy 2'x2' recess LED flat panel light 36W LED edge-lit luminaire suitable for armstrong/grid ceiling complete for low ceiling applications complete with all accessories pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specifed & directed.

Replacement of service cable of size 10 Sqmm 2 core 1100 volts grade heavy duty cable PVC insulated stranded alumn conductor, served with an inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm suspension wire or drawn in and including medium grade non metallic rigid PVC conduit as per site requirement, flat or circular all as required or directed.

XLPE insulated, armoured, heavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 16 Sqmm 2.0 core laid in trenches or passing through pipes/ducts or fixed to walls/poles including taking out old unvs cable complete all as specified. (Earth work, brick protection and sand cushioning shall be measured and paid for separately).

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC M-15, type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 27 of tender doucments.

M/s Parvesh Gupta (BID ID -3415495)

BAKSHI DEVI DASS AND SONS (BID ID -3415304)

M/s Anil Engineers & Builders (BID ID -3415657)

M/S IMRAN MAJID (BID ID -3400751)