REPAIR REPLACEMENT OF INT ELECT WIRING WITH FITTING AND FIXTURES CEILING FAN EXHAUST FAN WALL FAN GEYSERS REFRIGERATORS DESERT COOLERS WATER COOLERS AIR CONDITIONING DEEP FREEZERS ETC AND MAINT OF RESIDENTIAL ACCN OF DAD AT MIL STN DHRANGADHRA

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L PCC 40mm thick 1:2:4 of type B1 using 20mm graded stone aggregate as floor finishing surface even and smooth without using extra cement laid in pannels complete all as specified and directed.

S &F Non - skid Ceramic white tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over 15 mm thick screed bedding in CM 1:6 and pointed in white or coloured cement to match complete all as specified and as directed.

S&F Joint free Glazed ceramic tiles in vertical surface 450X 300X 7/8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendring in CM 1:4 complete all as specified and as directed.

Taking down cement plaster on brick walls incl. raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M & L 15 mm thick cement plaster on fair faces of brick work or concrete surface on wall in CM 1:4 finished fair and even complete all as specified and directed.

M & L 15mm thick cement plaster on fair faces of brick work or concrete surface on wall in CM 1:6 finished fair and even complete all as specified and directed.

M&L two coats of distemper oil emulsion on ceiling including preparation of newly plastered surface and complete all as specified.

Material and labour for preparation of newly plastered/unplastered surface of walls & applying two coats of cement base paint over a coat of white cement primer complete all as specified.

M&L for complete removal of existing treatment, preparation of surface and applying two coat of oil bound distemper on surfaces of walls over a coat of alkali resistant primer over 1 mm thick wall care putty all as specified complete all as specified.

M&L for preparation of old painted or plastered surfaces of walls etc by washing, rubbing down and applying one coat of cement base paint complete all as specified & directed.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified & directed.

M&L in repair for pre-painted hot dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed

Dismantling stone slab and tiles of any description or thickness in floors, aprons etc, laid dry and pointed complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise proviceded for complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc) sheet in roof covering complete all as specified and as directed.

S&F rolled mild steel section as in main and cross beams hip and jack rafters , purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates conforming to Fe-290, Gde E-165 all as specified and directed.

S&F in repairs for 15 mm bore medium grade galvanised steel tubing with all fittings and fixed (connciled) complete to walls and ceiling or laid in floor down complete all as specified and directed.

S&F in repairs for 20 mm bore medium grade galvanised steel tubing with all fittings and fixed complete to walls and ceiling or laid in floor complete all as specified and directed.

Taking down and refixing only old galvanized iron pipe 15mm bore in new or old position with new fittings as in wall and ceiling or laid in floors complete all as specified and directed.

S&F in repairs 15mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm -210 gms )complete all as specified and directed.

S&F in repairs 20mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm -210 gms )complete all as specified and directed.

S&F in repair 15 mm bore dia Stop/angle valves fancy type Chromium plated screwed down , high pressure , with capston head, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 20mm dia tubular Towel Rail 600mm long between flanges of brass chromium plated complete all as specified and directed.

S&F in repair brass Chromium plated shower roses 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair 32mm waste coupling of PTMT (half or full threaded) (minimum weight 40mm-60 gms) fixed in repair complete all as specified and as directed.

S&F in repair 15mm bore fency type CP Brass Bib taps with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed .

S&F in repair 15 mm dia Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair 20 mm dia Gun-metal, globe or gate valves,with iron wheel head, screwed both ends for iron pipe and fixed

S & F in repairs vitreous china hand wash basin white exclusive quality flat back size 550 x 400 mm including brackets, PVC waste pipe and waste coupling fixed complete all as specified and directed.

S&F in repairs 600mm long PVC Connection 15mm size with PTMT nuts complete all as specified and directed.

S&F in repairs 450mm long PVC Connection 15mm size with PTMT nuts complete all as specified and directed.

S&F in repair vitreous china wash down water closet, "Orissa pattern, size, 580x440mm white, with integral foot rest (excluding flushing cistern and flush pipe) but including provision of cement concrete bedding complete all as specified & directed.

S&F in repairs 10 litre capacity PVC valveless, Syphonic action type, fluhing cistern low level,white with inlet ball valve, float and handle complete all as specified and directed.

S&F in repairs 500 liters capacity rotational moulded polyethylene water storage tank (Cylindrical vertical with close top) hoisted and fixed in position including connections incl 20mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball all as specified.

S&F in repair sheet glass 4.00 mm thick ordinary quality and glazing with rubber and aluminium beading in square exc 0.5 sqm in each pane including taking down all as specified

S&F in repair sheet glass 3.00 mm thick ordinary quality and glazing with oil puttyin sqm n exc 0.5 sqm in each pane all as specified

M&L for 20 mm thick Granite (of any type of coloured) tiles maxhine cut in skirting/dado laid over cement screed and jointed with grey cement slurry ,and pointed with grey cement slurry ,and pointed with white cement with adimixture of pigment to match the shade of granite stone including grinding and polishing complete over 15mm thick screed bed in CM 1:6 incl moulding, chamfering of edges complete.

Supply and fixing in repairs SS Jet spray with flexible pipe 15mm dia not less than 1.50 mtr long complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified

Taking down chokhats or frames (without taking off shutters from the frame) exc 1.5 sqm and n.exc 4.00 sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and directed.

Taking down chokhats or frames (without taking off shutters from the frame) n.exc 1.50 sqm including cutting holes and making good reqd shape for hold fast block for new frame complete all as specified directed.

M&L 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides compete all as specified and directed by Engr-in-Charge.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified and directed.

M&L for preparation of new or previously steel surfaces of any description, over 10 cm width or girth, not otherwise described and evenly applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparing new wood & wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed.

M&L preparing old wood & wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

S&F for Pressed steel frames for doors (125X60mm) with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified directed

S&F standard aluminium section powder coated any colour as approved for Door/ window/ventilator frames/three track shutters sliding/ partitions etc including jointing cleat and rubber eading/linning, Pivot ,locking aragement and all hardware etc and fixed in position with stainless steel screws all as specified and as directed.

S&F for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. M S frame shall be covered with heat moulded plain coloured PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain coloured PVC sheet for top rail, lock rail and bottom rail; panelling of plain coloured PVC sheet to be fitted in the MS frame welded /sealed to the stiles & rails with 5mm x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm on exposed side of shutter. Note- Door shall be fabricated by authorized dealer of M/S Rajshree Indore using PVC sheet manufactured by M/S Rajshree Indore.

S&F for Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification and drawings including all fixtures shown on drawings. Make for materials : Rajshree Doors or equivalent as approved by GE. Note:-(i) Frames shall be fabricated by authorized dealer of M/S Rajshree Indore using PVC sheet manufactured by M/S Rajshree Indore. (ii) Provision of tie rod in shape of internal MS tube or round bar etc of any size adequate to keep the chowkhat in true position shall be provided before covering the frame with PVC sheet at workshop. For the purpose of measurement & payment length of chowkhat without tie rod shall be measured.

S&F 100 mm Butt hinges, medium weight, cold rolled mild steel, fixed to steel frames with and including welding etc complete all as specified.

S&F 200mm aluminium anodised barrel tower bolts of extruded section all as specified.

S&F 150mm aluminium anodised barrel tower bolts of extruded section all as specified.

S&F 300mm aluminium anodised sliding door bolt of extruded section all as specified

S& F 150 mm extruded aluminum alloy handles, fabricated type anodised.

S&F in Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring 150 mm long complte all as specified

Taking down carefully unserviceable copper/aluminium point wiring (Light, fan, socket or power) complete including unserviceable fittings and fixtures such as switches, ceiling roses, pendents, regulators, sockets, lamp holders, brackets, except ceiling fittings, bulk head fittings, tube light fittings etc. and making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for point wiring with PVC insulated, sheathed FRLS cable 1100 Volts grade, ISI marked multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) for phase, neutral & earth, single core drawn in and including medium grade PVC casing and capping double lock type 32mm in size, fire resistant, ISI marked including its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including pressed steel sunken concealed terminal box with 3mm thick industrial laminated sheet cover for mounting switches, sockets and fan regulators etc. complete all as specified and directed for the following :-

(a) One light/fan point controlled by one switch

(b) One light point controlled by two, 2- way switches.

(c) One 3 pin, 5 Amps, socket outlet on the same board controlled by another switch.

(d) One multi pin 5 Amps, socket outlet on Independent board.

(e) One bell/ buzzer point controlled by one push buttons independent

All as per srl item No. 60 here-in-before but for 6/16 Amp independent socket outlet using 2.5 sqmm single core wire (for phase, nuetral and earth) complete all as specified.

M&L for concealed type point wiring PVC insulated, sheathed FRLS cable 1100 Volts grade, ISI marked multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) for phase, neutral & earth, single core drawn in and including medium grade PVC conduit concealed type 20/25 mm in size, fire resistant, ISI marked including its fittings and fixtures such as tees, bends, elbows, junction boxes, etc. including pressed modular steel sunken concealed terminal box with modular white cover plate with frame for 2/4/6/8 modules for housing modular switches/sockets/fan regulators and making good the disturbed surfaces complete all as specified and directed by Engr-in-charge for the following :

(a) One modular light/fan point controlled by one switch

(b) One modular light point controlled by two, 2- way switches.

(c) One modular 3 pin, 5 Amps, socket outlet on the same board, controlled by another switch.

(d) One modular multi pin socket outlet, 5 Amps, on Independent board.

(e) One modular bell/buzzer point controlled by one push buttons independent.

All as per srl item No. 62 here-in-before but for 6/16 Amp independent socket outlet using 2.5 sqmm single core wire (for phase, nuetral and earth) complete all as specified.

S&F, in replacement, switch piano, flush button, single pole, one way, 5 Amps complete all as specified and directed

S&F, in replacement socket outlet, 3 pin, 5 Amps, flush type complete all as specified and directed

S&F, in replacement, switch piano, flush button, single pole, one way 15 Amps complete all as specified.

S&F, in replacement, socket outlet, 2 in 1, 3 pin, 6/16 Amps flush type complete all as specified and directed

S&F, in replacement, switch flush type 5 Amps, single pole, two ways complete all as specified and directed

S&F, in replacement, bell, A.C. 230 Volts, single pole, Ding doll, complete all as specified and directed.

S&F, in replacement, bell push, flush type 5 Amps complete all as specified and directed.

S&F, in replacement, ceiling fan step type regulator, AC 230 Volts complete all as specified and directed.

S&F, in replacement, ceiling rose, 3 terminal , any shade, of PVC/Polycarbonate, isolated body complete all as specified and directed

S&F, in replacement, lamp holder, PVC/Polycarbonate, with back plate suitable for batten fittings complete all as specified and directed

S&F , in replacement, modular switch 1 way 10A, 1 module complete all as specified and directed.

S&F , in replacement, modular socket 10 Amps, 3 pin, 2 module complete all as specified and directed.

S&F, in replacement modular switch 1 way 20A, 1 module complete all as specified and directed.

S&F, in replacement, modular socket 20A, 2/3 pin combined, 2 module complete all as specified and directed.

S&F , modular switch 2 way 10A, 1 module complete all as specified and directed.

S&F, in replacement, modular bell push 6 Amps, 1 module complete all as specified and directed.

S&F, in replacement, modular fan regulator, step type, sutabule for 1200/ 1400mm sweep, 1/2 module complete all as specified and directed.

S&F, in replacement, sheet metal enclosures, single pole & neutral with a two pin & earth plug and socket with one single pole MCB of 20 Amps, 10 KA, 240 volts complete all as specified and directed.

S&F, in replacement, sheet metal distribution board, SPN, 12 way 240 Volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar complete all as specified and directed.

S&F, in replacement, sheet metal distribution board, SPN, 8 way 240 Volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar complete all as specified and directed.

S&F, in replacement, sheet metal distribution board, SPN, 4 way 240 Volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar complete all as specified and directed.

S&F, in replacement, sheet metal distribution board, 3 phase with neutral (TPN), 4 way 415 Volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs with 200A tinned copper bus bar complete all as specified and directed

Supply and fix MCB SP 6-32A, 10 kA, C series, 230 Volts complete all as specified and directed

Supply and fix MCB SPN 32A, 10 kA, C series, 230 Volts complete all as specified and directed

Supply and fix MCB SPN 40-63A, 10 kA, C series, 230 Volts complete all as specified and directed

Supply and fix MCB TPN 40-63A, 10 kA, C series, 415 Volts complete all as specified and directed

S&F, in replacement, sub-main wiring with 3 single core (for phase, neutral & earth), 4 Sqmm PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper multi stranded conductor drawn in and including PVC casing and caping of 32mm size and earth wire drawn should be connected to main switch/DB and testing on completion complete all as specified and directed. Note: 3 runs of main conductor and one run of PVC casing and caping shall be measured as one unit length.

S&F, in replacement, sub-main wiring with 3 single core (for phase, neutral & earth), 4 Sqmm PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper multi stranded conductor drawn in and including PVC conduit concealed of 25mm size and earth wire drawn should be connected to main switch/DB and testing on completion complete all as specified and directed. Note: 3 runs of main conductor and one run of PVC conduit concealed shall be measured as one unit length.

S&F, in replacement, sub-main wiring with 5 single core (for 3 x phase, neutral & earth), 4 Sqmm PVC insulated, unsheathed, 1100 Volts grade, FRLS, copper multi stranded conductor drawn in and including PVC casing and caping of 32mm size and earth wire drawn should be connected to main switch/DB and testing on completion complete all as specified and directed. Note: 5 runs of main conductor and one run of PVC casing and caping shall be measured as one unit length.

S&F LED Adore Lamp 9W, B22 base 6500K CDL type complete all as directed by Engr-In-charge. Make: Havells/Crompton/Bajaj

M&L for checking electrical points such as light points, fittings & fixtures, MCBs, MCB DBs, check electric supply, locating & rectification of defects including carrying out minor repairs, fixing screws ,tightening of loose wires, applying PVC insulation tape, fixing fuse wire any type renewal of small pieces of wire upto 1.00 mtr length and similar work complete all as directed at site complete all as specified and directed. Note :- 1. The contractor's electricians & helpers should be receive the complaints Job cards from complaints cell on 0930 Hrs dailly basis and to attend the complaints with necessary tools. The complaints shall be attended and completed within same day.

S&F in replacement distribution board VTPN, 4 way, 415 volts, factory made powder coated, double door with neutral and earth link, including 3 pole MCCB 100 Amps rating, 16KA breaking capacity for incoming supply and including suitable number of MCB SP for out going supply complete all as specified and directed.

S&F in replacement surface/recess mounted decorative type LED 12 watts ceiling panel light of size 6" x 6" environmental friendly, new generation, aesthetically designed, ultra modern luminaire with high brightness SMD LEDs as light source complete all as specified and directed by Engr-in-charge.

S&F in replacement surface/recess mounted decorative type LED 7 watts ceiling round light environmental friendly, new generation, aesthetically designed, ultra modern luminaire with high brightness SMD LEDs as light source complete all as specified and directed by Engr-in-charge.

S&F in replacement wall mounted decorative type 3/5 watts LED scenerio spot light environmental friendly, new generation, aesthetically designed, ultra modern luminaire with high brightness SMD LEDs as light source complete all as specified and directed by Engr-in-charge.

S&F, in replacement, LED light fitting, batten type, housed in extruded from powder coated aluminium, 20 watt for soft diffuser lighting with and including lamp prewired and connecting to ceiling rose with 3 core flexible round white cable complete all as specified and directed.

S&F in replacement wall mounted fancy bracket designed decorative glass type LED light with holder B22 new generation, aesthetically designed, ultra modern luminaire with warm white 9/10Watts LED bulb complete all as specified and directed by Engr-in-charge.

S&F, in replacement, LED light fitting, batten type, housed in extruded from powder coated aluminium, 10 watt for soft diffuser lighting with and including lamp and connecting to ceiling rose with 3 core flexible round white cable complete all as specified and directed.

S & F in replacement Box type decorative double side connection LED light fitting, 1 x 20 Watt, 230 V,C surfacce mounting white powder coated CRCA sheet steel housing with crescent light opening in a perforated metallic frame complete with 20 W LED tube rod (double side connection) with all accessories prewired and connecting to ceiling rose with 3 core flexible round white cable complete all as specified and directed. Make: Bajaj / Havell / wipro/ crompton.

S&F in replacement LED flat panel of size 2' x 2', 36 Watts, environmental friendly, new generation, aesthetically designed, ultra modern recess mounting luminaire with high brightness of white/warm white in colour, SMD LEDs as light source, suitable for Armstrong/Grid ceiling complete all as specified and directed by Engr-in-charge.

Supply and fixing in replacement LED energy efficient street light fitting 30 watt LED pressure die cast aluminium housing in heat resistant glass covered with IP-65 protection with fixing accessories complete.

Supply and fixing in replacement LED bulk head with glass light fitting 10 watt with IP-65 protection with fixing accessories complete all as specified and directed.

Taking down of exhaust fan PVC type 150/200/250/300mm sweep for repair, removing existing burnt motor and replacement of motor/fan blade etc., refixing, testing complete all as specified and directed. Note : Where ever required the fan motor/fan blade shall be measured and paid separately under respective item of this schedule as "Supply only".

S&F exhaust fan, 150 mm sweep, 1200 rpm, PVC body, AC single phase, 230 volts, 50 Hz with louvers including connecting up with ceiling rose complete all as specified and as directed.

Taking down/Disconnecting carefully water storage type water heater of 10 ltr cap of any make, disconnecting electric connection and dismantling for repair by taking out the syphon assembly of thermostat, heating element and cleaning, de-scaling the inner tank by chemical compound including soldering, brazing if required, Re-assembling and re-fixing the geyser after cleaning & servicing at existing position/location complete all as specified and directed. Note:- (i) Heating element, thermostat, air release valve, safty valve, indicating lamp and syphone assembly shall be measured and paid under relevant items as "Supply Only". (ii) The rate quoted are deemed to include cost of soldering/brazing work if required at site.

Supply only heating element of 1.5 KW with circular or triangular base suitable for existing entry of geysers of any make complete all as specified and directed.

Supply only thermostat assembly for existing geysers make, tempetrature setting up to 85 degree centigrade, ISI marked complete all as specified and directed.

Supply only indicating lamp suitable for existing entry of geyser complete all as specified and directed.

S&F, in repair, inlet/outlet (cold& hot) pipe of 15mm bore 450mm long, PVC connection, heavy duty, high density suitable for temperature upto 100 degree complete all as specified and directed.

S&F, in repairs, water lifting submerssible pump (ISI Marked) suitable to operate on 230V AC supply of desert cooler and connecting electically, complete all as specified and directed.

S&F, in repair, fan motor heavy duty, copper wire type (ISI Marked), 1/2 HP, 230 volt single phase suitable for existing desert coolers of Op Work Shelters with fixing clamps, complete all as specified and directed

S&F, in repair, fan motor blade, 230 volt single phase suitable for existing desert coolers with fixing clamps, nuts, bolts, washers etc. complete all as specified and directed

S&F in repair, PVC distributer and PVC elbows suitable for water distribution assembly of desert coolers complete all as specified and directed.

S&F, in repair, grass pads, existing type for cooling air, superior quality, suitable size (big size) for Op shelter desert cooler complete all as specified and directed

S&F, in repair, PVC flexible pipe 12mm dia suitable for submersible pump of desert cooler complete all as specified and directed.

S&F, in repair, PVC insulated, sheathed cable 3 core, 1.5 Sqmm, multistandard copper conductors minimum length 2 mtr for Desert Cooler, water coolers/ refrigerators as main cord with 5A, 3 pin top complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth Lead 4 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I connected to earth test point using earth wire of 4mm as earth lead all as specified and testing on completion including provision of earth lead protected by 15 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note : Rate quoted by tenderers shall be deemed to include for following provisions:-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to DB upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 15 mm bore light grade 7.5m.

Taking down of ceiling fan 1200/1400 mm sweep from existing position/hook, dismantling blades deposite to store and removing fan cleaning, servicing or re-fixing on same position after complete all as specified and directed.

De-assembling (opening) of the ceiling fan, 1200mm/1400mm sweep for repair, removing existing burnt winding, rewinding as per existing winding the same gauge and weight with super enameled copper winding wire of appropriate gauge, slot insulation, heat varnishing, greasing and re-assembling including replacement of split pin and flexible twisted copper cable of 23/0.0076 gauge, testing complete all as specified and directed. Note:- (i) Contractor shall collect the Ceiling fan for repair from Store Yard/site of AGE E/M and fix the repaired fan on the location given by Engineer-in-charge. (ii) Where ever required the Ball bearing, bush and capacitor shall be measured and paid separately under respective item of this schedule as "Supply only".

Supply only capacitor of 2.5 Mfd suitable for 1200/1400 mm sweep ceiling fan.

Supply only ball bearing suitable for 1200mm/1400mm sweep ceiling fan.

Supply only gun metal bush suitable for 1200/1400mm sweep ceiling fan of appropriate make.

S & F, in repair, capacitor of 2.5 Mfd suitable for 1200 mm/1400mm sweep ceiling fan.

S&F, in repair, PVC canopy set (Upper & Lower) suitable for ceiling fans complete all as specified and directed.

S & F in repair, ceiling fan down round metal rod/pipe of lenghts of one feet suitable for 1200 mm/1400mm sweep ceiling fan.

S&F, in repair, MS hanging clamp with rubber bush, bolts, nuts & washer with split pin suitable for ceiling fan complete all as specified and directed.

M & L Painting of ceiling fans complete, in situ/in store with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning/removing existing paint and all dust etc.

S&F in repair, PCB circuit complete for BLDC fan as per fan manufacturer make complete all as specified and as directed by Engr-in-Charge

Taking down exhaust fan metal body of size 200/230/250/300/380/450 mm sweep from existing position, cleaning, servicing and re-fixing on same position complete all as specified and directed by Engr-in-charge.

De-assembling (Opening) of exhaust fan 200/230/250/300 mm sweep for repair, removing existing burnt winding, rewinding as per existing winding gauge & weight with super enameled copper winding wire of approprite gauge, slot insulation heat varnishing, greasing, re-assembling, refixing, testing complete all as specified and directed. Note:- (i) Contractor shall collect the exhaust fan for repair from Store/Site Yard of AGE E/M and Refix repaired fan on the location given by Engineer-in-charge. (ii) Where ever required the Ball bearing, bush and capacitor shall be measured and paid separately under respective item of this schedule as "Supply only".

De-assembling (Opening) of exhaust fan 380/ 450 mm sweep for repair, removing existing burnt winding, rewinding as per existing winding gauge & weight with super enameled copper winding wire of approprite gauge, slot insulation heat varnishing, greasing, re-assembling, refixing, testing complete all as specified and directed. Note:- (i) Contractor shall collect the exhaust fan for repair from Store/Site Yard of AGE E/M and Refix repaired fan on the location given by Engineer-in-charge. (ii) Where ever required the Ball bearing, bush and capacitor shall be measured and paid separately under respective item of this schedule as "Supply only".

Supply only capacitor of 4.0 Mfd suitable for exhaust fan.

Supply only ball bearing suitable for 200/230/250/300mm sweep exhaust fan complete.

Supply only ball bearing suitable for 380/450 mm sweep exhaust fan complete.

Supply only gun metal bush suitable for 200/230/250/300mm sweep exhaust fan complete.

Supply only gun metal bush suitable for 380/450mm sweep exhaust fan complete.

M&L for preparation of surfaces of exhaust fan of size 200/230/250/300/380/ 450mm including blade, frame/louver and apply one coat of synthetic enamel paint with spraying after taking down in respective items all as specified and directed by Engg-in-change.

Taking down of exhaust fan PVC type 200/250/300mm sweep for repair, removing existing burnt motor and replacement of motor/fan blade etc., refixing, testing complete all as specified and directed. Note : Where ever required the fan motor/fan blade shall be measured and paid separately under respective item of this schedule as "Supply only".

Supply only PVC exhaust fan motor suitable for 200/250/300mm sweep complete all as specified and as directed.

Supply only PVC exhaust fan blade suitable for 200/250/300mm sweep complete all as specified and as directed.

S&F exhaust fan, 200 mm sweep, 1200 rpm, PVC body, AC single phase, 230 volts, 50 Hz with louvers including connecting up with ceiling rose complete all as specified and as directed.

S&F exhaust fan, 250 mm sweep, 1200 rpm, PVC body, AC single phase, 230 volts, 50 Hz with louvers including connecting up with ceiling rose complete all as specified and as directed.

S&F exhaust fan, 300 mm sweep, 1200 rpm, PVC body, AC single phase, 230 volts, 50 Hz with louvers including connecting up with ceiling rose complete all as specified and as directed.

S&F, Polycarbonate single phase meter box for outdoor type IP-66 with arrangement of fixing in meter box energy meter with front open for punching of recharge token complete all as specified and directed.

S&F, Polycarbonate three phase meter box for outdoor type IP-66 with arrangement of fixing in meter box energy meter with front open for punching of recharge token complete all as specified and directed.

S&F, seal for single phase or three phase electrical energy meter of suitable size with locking arrangement complete all as specified and directed

Taking down/Disconnecting carefully water storage type water heater of 25/50 ltr cap of any make, disconnecting electric connection and dismantling for repair by taking out the syphon assembly of thermostat, heating element and cleaning, de-scaling the inner tank by chemical compound including soldering, brazing if required, Re-assembling and re-fixing the geyser after cleaning & servicing at existing position/location complete all as specified and directed. Note:- (i) Heating element, thermostat, air release valve, safty valve, indicating lamp and syphone assembly shall be measured and paid under relevant items as "Supply Only". (ii) The rate quoted are deemed to include cost of soldering/brazing work if required at site.

Supply only heating element of 1.5 KW with circular or triangular base suitable for existing entry of geysers of any make complete all as specified and directed.

Supply only heating element of 2.0 KW with circular or triangular base suitable for existing entry of geysers of any make complete all as specified and directed.

Supply only thermostat assembly for existing geysers make, tempetrature setting up to 85 degree centigrade, ISI marked complete all as specified and directed.

Supply only indicating lamp suitable for existing entry of geyser complete all as specified and directed.

S&F, in repair, inlet/outlet (cold& hot) pipe of 15mm bore 400mm long, PVC connection, high density suitable for temperature upto 100 degree complete all as specified and directed.

S&F, in repair, inlet/outlet (hot & cold) pipe of 15mm bore 600mm long, PVC connection, high density suitable for temperature upto 100 degree complete all as specified and directed.

S&F, in repair, water storage type copper inner tank of 25 ltr capacity as per existing tank complete all as specified and directed.

S&F, in repair, water storage type copper inner tank of 50 ltr capacity as per existing tank complete all as specified and directed.

S&F, in repair, water storage type steel body outer tank of 25 ltr capacity as per existing tank complete all as specified and directed.

S&F, in repair, water storage type steel body outer tank of 50 ltr capacity as per existing tank complete all as specified and directed.

S&F, in repair, semi circular bottom cover plate of 25/50 ltr capacity geyser duly painted of appropriate make complete all as specified and directed.

S&F, in repair, Geyser syphon assembly (flange) made out of copper/steel as existing including heat resistance and leak proof gasket suitble for 25/50 ltrs capacity geyser all as specified and directed.

S&F, in repair, safty relief valve, as per existing of 25/50 ltr capacity geyser complete all as specified and directed.

S&F, in repair, glass wool superior quality around the water container as heat resistance upto full capacity complete all as specified and directed.

Taking down and Refixing up carefully 1.5 ton window or 1.5/2 ton split type AC after checking of electric wiring and parts , cleaning of unit, lubrication of motor, capillary, filter & servicing at existing position/location complete all as specified and directed. Note:- (i) Compressor, capacitor, starting relay, overload protection shall be separetely measured and paid. (ii) The rate quoted are deemed to include cost of soldering/brazing work if required at site.

S&F, in repair, Indoor unit AC Swing motor blades (replaced with original company of same make as per existing), suitable for working on single phase, 50 HZ AC , 1.5/2 Ton split type AC with electric connection, testing complete all as specified and directed.

S&F, in repair, Indoor unit AC blower fan motor (replaced with original company of same make as per existing), suitable for working on single phase, 50 Hz AC supply, 1.5/2 Ton type split AC with electric connection, testing complete all as specified and directed.

S&F, in repair, Indoor unit AC blower fan bush (replaced with original company of same make as per existing), suitable for working on single phase, 50 Hz AC supply in split type AC with electric connection, testing complete all as specified and directed.

S&F, in repair, Indoor unit AC Cooling condenser (replaced with original/as per existing), suitable for working on single phase, 50 Hz AC supply, 1.5/2 Ton split type AC with electric connection, testing complete all as specified and directed.

S&F, in repair, Indoor unit AC Display unit (replaced with original/as per existing), suitable for working on single phase, 50 HZ AC supply 1.5/2 Ton split type AC with electric connection, testing complete all as specified and directed.

S&F, in repair, Remote with PCB Circuit of 1.5/2 Ton capacity split ACs (replaced with as per existing), suitable for working on single phase, 50 HZ AC supply in split type AC with electric connection, testing complete all as specified and directed.

S&F, in repair, Outdoor unit AC Fan motor blade of suitable size (replaced with original/as per existing), suitable for working on single phase, 50 HZ AC supply, 1.5/2 Ton capacity type split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, Outdoor unit AC copper coils of suitable size (replaced with original/as per existing), suitable for working on single phase, 50 HZ AC supply , 1.5/2 Ton capacity type split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, Outdoor unit AC insulation tubing/cover as per existing tubing tickness of 6 feet lenght For 1/4" & 1/2" size of copper coils(replaced with original/as per existing), suitable for working on single phase, 50 HZ AC supply, 1.5/2 Ton capacity type split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, Outdoor unit condenser fan motor of suitable size (replaced with original company of same make/as per existing), suitable for working on single phase, 50 HZ AC supply 1.5/2 Ton capacity type split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, Outdoor unit AC heat condenser coil of suitable size (replaced with original company of same make/as per existing), suitable for working on single phase, 50 HZ AC supply, 1.5/2 Ton capacity type split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, sealed unit compressor (replaced with original company, new compressor of same make as per existing) suitable for Operation on single phase, 50 HZ AC supply for 1.5 ton split type AC including making necessary refrigerent pipe connection, electric connection, checking of leakage and testing complete all as specified and directed.

S&F, in repair, Outdoor unit AC Compressor capacitor of suitable capacity (replaced with original company of same make/as per existing), suitable for working on single phase, 50 HZ AC supply 1.5/2ton split type AC with electric connection, testing complete all as specified and directed.

M&L, in repair, Outdoor unit AC Gas valves of suitable size (replaced with original company of same make/as per existing),For 1.5/2 Ton split type AC with all conecting accessories, testing complete all as specified and directed.

S&F, in repair, Outdoor unit AC power relay contactors of suitable capacity (replaced with original company of same make/as per existing), suitable for working on single phase, 50 HZ AC supply, 1.5/2 Ton split type AC with electric connection, testing complete all as specified and directed.

M&L for refrigerent charging with R 22/R 134/R 410 for window AC of capacity 1.5 Ton and making necessary copper tubing connection for refrigerent line, soldering, brassing of leakage point complete all as specified and directed.

M&L for refrigerent charging with R 22/R 134/R 410 for split type AC of capacity 1.5 & 2 Ton and making necessary copper tubing connection for refrigerent line, soldering, brassing of leakage point complete all as specified and directed.

S&F, in repair, sealed unit compressor (replaced with original company, new compressor of same make as per existing) suitable for Operation on single phase, 50 HZ AC supply for 2 ton split type AC including making necessary refrigerent pipe connection, electric connection, checking of leakage and testing complete all as specified and directed.

S&F,in repair, Running capacitor of 36 MFD capacity for 1.5/2 ton split type AC suitable operation on 230 Volt, 50 Hz complete all as specified and directed.

S&F,in repair, Running capacitor of 45 MFD capacity for 1.5 Ton window/split type AC suitable operation on 230 Volt, 50 Hz complete all as specified and directed.

S&F,in repair, Running capacitor of 60 MFD capacity for window/split type AC suitable operation on 230 Volt, 50 Hz complete all as specified and directed.

S&F, in repair, Heavy duty ODU (outdoor unit) Stand/installation bracket kit with brackets, fasteners, nuts and washer for 1.5/2 ton split type AC complete all as specified and directed.

M&L, in repair, starting relay of window/Split type A/C, 1.5 to 2 Ton capacity including making necessary electric connections complete all as specified and directed.

M&L, in repair, Thermostate switch suitable for window/Split type A/C, 1.5 to 2 Ton capacity including making necessary electric connections complete all as specified and directed.

S&F, in replacement, indoor unit sealed complete set for split type AC of 1.5 TR (replaced with original company of same make as per existing), suitable for working on single phase, 50 Hz AC supply with electric connection, testing complete all as specified and directed.

S&F, in replacement, outdoor unit sealed complete set for split type AC of 1.5 TR (replaced with original company of same make as per existing), suitable for working on single phase, 50 Hz AC supply with electric connection, testing complete all as specified and directed.

M&L, in repair, Sensors for all model type AC.s, including making necessary electric connections complete all as specified and directed.

S&F, in repair, overload protector for split type AC of 1.5/2 Ton capacity complete all as specified and directed.

M&L, in repair, copper piping of 1/2" & 1/4" size , wiring between Indoor & Outdoor for 1.5/2 ton split type AC including all necessary connecting accesssories complete all as specified and directed.

S&F, in repair, indoor unit DC motor (replaced with original company of same make/as per existing), of suitable for working on single phase, 50 HZ AC supply, 1.5/2 Ton capacity inverter type Split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, DC indoor circuit (replaced with original company of same make/as per existing), of suitable for working on single phase, 50 HZ AC supply, 1.5/2 Ton capacity inverter type Split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, inverter outdoor unit circuit (replaced with original company of same make/as per existing), Of suitable for working on single phase, 50 HZ AC supply, 1.5/2 Ton capacity inverter type Split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, inverter outdoor unit DC compressor (replaced with original company of same make/as per existing), Of suitable for working on single phase, 50 HZ AC supply, 1.5/2 Ton capacity INVERTER Type Split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, inverter outdoor unit sensor (replaced with original company of same make/as per existing), Of suitable for working on single phase, 50 HZ AC supply, 1.5/2 Ton capacity INVERTER Type Split ACs with electric connection, testing complete all as specified and directed.

S&F, in repair, sealed unit compressor (replaced with original company new compressor of same make as per existing ) suitable for working on single phase 50 Hz AC supply in refrigerator 1/8 HP (165 to 210 Ltrs) capacity including making connection and brazing of necessary refrigerent pipe, electric connections and testing for leakproof complete all as specified and directed.

S&F, in repair, sealed unit compressor (replaced with original company new compressor of same make as per existing ) suitable for working on single phase 50 Hz AC supply in refrigerator 1/6 HP (265 to 310 Ltrs) capacity including making connection and brazing of necessary refrigerent pipe, electric connections and testing for leakproof complete all as specified and directed.

S&F, in repair,Evaporator of 165/180L Capacity (replaced with original company new compressor of same make as per existing ) suitable for working on single phase 50 Hz AC supply in refrigerator 1/8 & 1/6 HP (180 to 310 Ltrs) capacity including making connection and brazing of necessary refrigerent pipe, electric connections and testing for leakproof complete all as specified and directed.

S&F, in repair, sealed unit compressor (replaced with original company new compressor of same make as per existing) suitable for working on single phase 50 Hz AC supply in deep freezer 200 Ltrs capacity including making connection and brazing of necessary refrigerent pipe, electric connections and testing for leakproof complete all as specified and directed.

S&F, in repair, sealed unit compressor (replaced with original company new compressor of same make as per existing) suitable for working on single phase 50 Hz AC supply in deep freezer 310/320 Ltrs capacity including making connection and brazing of necessary refrigerent pipe, electric connections and testing for leakproof complete all as specified and directed.

M&L, in repair, starting relay of Refrigerator 1/8 to 1/6 HP capacity including making necessary electric connections complete all as specified and directed.

S&F, in repair, overload protector of Refrigerator and Deep freezer 165 Ltr to 320 Ltr complete all as specified and directed.

S&F, in repair, Deep freezer condenser (replaced with original company new compressor of same make as per existing) suitable for working on single phase 50 Hz AC supply in deep freezer 200/310/320 Ltrs capacity including making connection and brazing of necessary refrigerent pipe, electric connections and testing for leakproof complete all as specified and directed.

S&F, in repair, Deep freezer condenser fan motor (replaced with original company new compressor of same make as per existing) suitable for working on single phase 50 Hz AC supply in deep freezer 200/310/320 Ltrs capacity including making connection, electric connections and testing complete all as specified and directed.

S&F, in repair, Deep freezer cooling fan of 35x35x10mm (replaced with original company new compressor of same make as per existing) suitable for working on single phase 50 Hz AC supply in deep freezer 200/310/320 Ltrs capacity including making connection, electric connections and testing complete all as specified and directed.

M&L for refrigerent charging with R-134a for Deep Freezer of capacity 200 Ltr to 320 Ltr and making necessary copper tubing connection for refrigerent line, soldering, brassing of leakage point complete all as specified and directed.

M&L for refrigerent charging with R-600a for Refrigerator of capacity 165 Ltr to 320 Ltr and making necessary copper tubing connection for refrigerent line, soldering, brassing of leakage point complete all as specified and directed.

S&F, in repair, sealed unit compressor (replaced with original company new compressor of same make as per existing ) suitable for working on single phase 50 Hz AC supply in water cooler of 40/80 Ltrs capacity including making connection and brazing of necessary refrigerent pipe, electric connections and testing for leakproof complete all as specified and directed.

M&L, in repair, starting relay of water coolers 40/80 Ltr capacity including making necessary electric connections complete all as specified and directed.

S&F, in repair, overload protector of water cooler up to 120/150 Ltr complete all as specified and directed.

M&L for refrigerent charging with R-22/R-134 for Water Cooler of capacity 40/80 Ltr and making necessary copper tubing connection for refrigerent line, soldering, brassing of leakage point complete all as specified and directed.

M&L, in repair, Thermostate suitable for water cooler up to 120 ltrs capacity including making necessary electric connections complete all as specified and directed.

M&L, in repair, Thermostate suitable for Refrigerator & deef freezer up to 320 ltrs capacity including making necessary electric connections complete all as specified and directed.

S&F, in repair, Running capacitor, 230 Volts, SP, 4.0 MFD complete all as specified and directed.

S&F, in repair, Running capacitor, 230 Volts, SP, 6.3 MFD complete all as specified and directed.

S&F, in repairs, water lifting submerssible pump (ISI Marked) suitable to operate on 230V AC supply of desert cooler and connecting electically, complete all as specified and directed.

S&F, in repair, fan motor (ISI Marked), 1/6 HP, 230 volt single phase of existing desert cooler with fixing clamps, complete all as specified and directed

S&F, in repair, fan motor blade, 230 volt single phase suitable for existing desert coolers with fixing clamps, nuts, bolts, washers etc. complete all as specified and directed

S&F, in repair, water storage tank of minimum size 0.8m x 0.8m x 0.2 (L x W x H), steel body, fabricated out of CRCA sheet of 0.6mm thick duly painted with two coats of synthetic enamel paint suitable for existing desert cooler complete all as specified and directed

S&F in repair, PVC distributer and PVC elbows suitable for water distribution assembly of desert coolers complete all as specified and directed.

S&F, in repair, grass pads, superior quality, size 60x45 cm (approximate), complete all as specified and directed

S&F, in repair, PVC flexible pipe 12mm dia suitable for submersible pump of desert cooler complete all as specified and directed.

S&F, in repair, PVC insulated, sheathed cable 3 core, 1.5 Sqmm, multistandard copper conductors minimum length 2 mtr for Desert Cooler, water coolers/ refrigerators as main cord with 5A, 3 pin top complete all as specified and directed.

Badri Electricals (BID ID -3391809)

ALBA AC AND REF SERVICES (BID ID -3386470)

Abhishek Enterprises (BID ID -3390809)